Determination of cut-off time of accelerated aging test under temperature stress for LED lamps

To acquire a rational minimum cut-off time and the precision of lifetime prediction with respect to cut-off time for the accelerated aging test of LED lamps, fifth-order moving average error estimation is adopted in this paper. Eighteen LED lamps from the same batch are selected for two accelerated aging tests, with 10 samples at 80 ℃ and eight samples at 85 ℃. First, the accelerated lifetime of each lamp is acquired by exponential fitting of the lumen maintenances of the lamp for a certain cut-offtime With the acquired lifetimes of all lamps, the two-parameter Weibull distribution of the failure probability is obtained, and the medium lifetime is calculated. Then, the precision of the medium lifetime prediction for different cut-off times is obtained by moving average error estimation. It is shown that there exists a minimum cut-off time for the accelerated aging test, which can be determined by the variation of the moving average error versus the cut-offtime. When the cut-off time is less than this value, the lifetime estimation is irrational. For a given cut-off time, the precision of lifetime prediction can be computed by average error evaluation, and the error of lifetime estimation decreases gradually as the cut-off time- increases. The minimum cut-off time and medium lifetime of LED lamps are both sensitive to thermal stress. The minimum cut-off time is 1104 h with the lifetime esti- mation error of 1.15% for the test at 80 ~C, and 936 h with the lifetime estimation error of 1.24% for the test at 85 ℃. With the lifetime estimation error of about 0.46%, the median lifetimes are 7310 h and 4598 h for the tests at 80 ℃ and 85℃, respectively.

Property changes of anchor grout calcined ginger nuts admixed with fly ash and quartz sand after accelerated ageing tests

Calcined ginger nuts admixed by fly ash and quartz sand (CGN-(F+S)) has been validated to be basically compatible to earthen sites as an anchor grout. Accelerated ageing tests including water stability test, temperature and humidity cycling test, soundness test and alkali resistance test are conducted with the objective to further research the property changes of CGN-(F+S) grout. Density, surface hardness, water penetration capacity, water permeability capacity, soluble salt, scanning electron microscopy (SEM) images and energy dispersive spectrometry (EDS) spectrum of these samples have been tested after accelerated ageing tests. The results show that densities of samples decrease, surface hardness, water penetration capacity and water permeability capacity of samples increase generally. Besides, soluble salt analysis, SEM and EDS results well corroborate the changes. Based on the results it can be concluded that property changes are most serious after temperature and humidity cycling test, followed by water stability, soundness and alkali resistance test in sequence. But in general, CGN-(F+S) still has good durability.

Natural Ageing Tests to Study In-service Different Facade Solutions--ETICS and Premixed One-Coat Rendered Walls

In situ testing provides accurate characterization of existing degradation mechanisms of materials and building systems which helps reducing the subjectivity of visual inspections especially when ageing under natural ageing conditions is carried out over significant periods of time. In this work, data collected from field experimental campaigns over 10 years after construction using several premixed one-coat rendered walls and over 4 and 6 years after construction in the case of ETICS （external thermal insulation composite systems） are presented and discussed. The influence of hydrophobic agents on the performance of both types of facades in terms of surface condition and water penetration was assessed by visual inspections, Karsten test and capillary tests. Additionally, adhesion tests and subsequent evaluation of porosity were also carried out for premixed one-coat mortars. The results obtained have shown that ageing of the rendering solutions, especially after 5 or 6 years in-service, results from the loss of resistance to liquid water penetration, especially at the surface. Yet, additional mechanisms such as leaching of hydrophobic agents and photochemical degradation are thought to be involved, too. Moreover, the results obtained using the Karsten test proved to be the most reliable method to determine the loss of water penetration resistance and predict the ageing of facade solutions. The information collected and the correlations established can help developing solutions to prevent early ageing and implement appropriate maintenance plans to delay their effect.

A Study of Estimating the Safe Storage Life, Self-accelerating Decomposition Temperature and Critical Temperature of Thermal Explosion of Double-base Propellant Using Isothermal and Non-isothermal Decomposition Behaviours

A method of estimating the safe storage life （τ）, self-accelerating decomposition temperature （TsADT） and critical temperature of thermal explosion （Tb） of double-base propellant using isothermal and non-isothermal decomposition behaviours is presented. For double-base propellant composed of 56±1wt% of nitrocellulose （NC）, 27±0.5wt% of nitroglycerine （NG）, 8.15±0.15wt% of dinitrotoluene （DNT）, 2.5±0.1wt% of methyl centralite, 5.0±0.15wt% of catalyst and 1.0±0.1wt% of other, the values of r of 49.4 years at 40℃, of TSAOT of 151.35℃ and of Tb of 163.01℃ were obtained.

Microstructure Evolution of T91 Heat-Resistant Steels after Long-Time Aging

To investigate the evolution of microstructure damage degree and the precipitated phases of heat-resistant metal in power plant under high temperature and stress environment, the high- temperature aging tests were conducted to investigate the aging behavior of T91 steel at different temperatures and stress. The optical microscopy, scanning electron microscopy, and transmis- sion electron microscopy were used to investigate the structure and precipitated phases, the results showed that the orientation characteristics of tempered martensite was dispersed, and the grain size is obviously increased. The density of dislocation decreased with increasing temperature and stress. The important strengthen- ing phase of M23C6 （M=Fe, Cr） was coarsened by the diffusion of main alloying elements Cr, while the smaller size MX （M=Nb,V; X=C, N） phase distributed in the grain is relatively stable in the aging.

Online aging study of a high rate MRPC

With the constant increase of accelerator luminosity, the rate requirements of MRPC detectors have become very important, and the aging characteristics of the detector have to be studied meticulously. An online aging test system has been set up in our lab, and in this paper the setupof the system is described and the performance stability of a high-rate MRPC studied over a long running time under a high luminosity environment. The high rate MRPC was irradiated by X-rays for 36 days and the accumulated charge density reached 0.1 C/cm2. No obvious performance degradation was observed for the detector.

Effect of temperature and moisture on the luminescence properties of silicone filled with YAG phosphor

In order to determine the environmental effects on the luminescence properties of a phosphor layer for high-power light emitting diodes, a high humidity and temperature test （85℃/85%RH） and a thermal aging test （85℃） were performed on silicone/YAG phosphor composites. The luminescence properties of silicone/phosphor composites are monitored by a fluorescence spectrometer. The results show that high temperature could result in an increase in conversion efficiency of composites during the early aging stage and red shift of YAG phosphor; and high humidity could result in a significant decrease in conversion efficiency of composites while having a small influence upon the optimal excitation wavelength of the YAG phosphor.

Ageing of GaN HEMT devices： which degradation indicators？

A following of diverse degradation indicators during the ageing in operational conditions of A1- GaN/GaN HEMTs （high electron mobility transistors） is proposed. Measurements of pulsed I-V, Schottky barrier height, RF output power and gate current versus output power during the early phase of the ageing test （2000 h on a 6000 h total） are presented. These preliminary results give insight on some of the principal degradation indicators that are interesting to follow during an ageing test close to operational conditions on such components.