Influence of abrasive hardness on erosion wear of abrasive air jets

To make clear the influence of abrasive hardness on the erosion effect,the erosion experiments of abrasive air jet with the same impact energy were carried out.The influence of abrasive hardness on the erosion effect is clarified by comparing the different erosion depths.The main conclusions are as follows.Under the same mass flow rate and mesh number,the abrasive with a higher density needs greater pressure irrespective of hardness.After erosion damage,the abrasive size exhibits a Weibull distribution.The shape parameterβand Weibull distribution function of four types of abrasives are derived by the least squares method;moreover,βis found to have a quadratic relation with abrasive hardness.The results of the erosion experiments show that abrasive hardness and erosion depth are quadratically related.By calculating the increase in surface energy after abrasive erosion crushing,it is found that abrasive hardness has a quadratic relation with surface energy and that the increases in erosion depth and surface energy consumption are basically identical.In conclusion,the effect is a soft abrasive impact when the ratio of abrasive hardness(Ha)to the material hardness(Hm)is<2.6,and it is a hard abrasive impact when Ha/Hm>3.

A novel approach of jet polishing for interior surface of small-grooved components using three developed setups

It is a challenge to polish the interior surface of an additively manufactured component with complex structures and groove sizes less than 1 mm.Traditional polishing methods are disabled to polish the component,meanwhile keeping the structure intact.To overcome this challenge,small-grooved components made of aluminum alloy with sizes less than 1 mm were fabricated by a custom-made printer.A novel approach to multi-phase jet(MPJ)polishing is proposed,utilizing a self-developed polisher that incorporates solid,liquid,and gas phases.In contrast,abrasive air jet(AAJ)polishing is recommended,employing a customized polisher that combines solid and gas phases.After jet polishing,surface roughness(Sa)on the interior surface of grooves decreases from pristine 8.596μm to 0.701μm and 0.336μm via AAJ polishing and MPJ polishing,respectively,and Sa reduces 92%and 96%,correspondingly.Furthermore,a formula defining the relationship between linear energy density and unit defect volume has been developed.The optimized parameters in additive manufacturing are that linear energy density varies from 0.135 J mm^(-1)to 0.22 J mm^(-1).The unit area defect volume achieved via the optimized parameters decreases to 1/12 of that achieved via non-optimized ones.Computational fluid dynamics simulation results reveal that material is removed by shear stress,and the alumina abrasives experience multiple collisions with the defects on the heat pipe groove,resulting in uniform material removal.This is in good agreement with the experimental results.The novel proposed setups,approach,and findings provide new insights into manufacturing complex-structured components,polishing the small-grooved structure,and keeping it unbroken.

The influence of four dual-cure resin cements and surface treatment selection to bond strength of fiber post

In this study, we evaluate the influence of post surface pre-treatments on the bond strength of four different cements to glass fiber posts. Eighty extracted human maxillary central incisors and canines were endodontically treated and standardized post spaces were prepared. Four post pre-treatments were tested： （i） no pre-treatment （NS, control）, （ii） sandblasting （SA）, （iii） silanization （SI） and （iv） sandblasting followed by silanization （SS）. Per pre-treatment, four dual-cure resin cements were used for luting posts： DMG LUXACORE Smartmix Dual, Multilink Automix, RelyX Unicem and Panavia F2.0. All the specimens were subjected to micro push-out test. Two-way analysis of variance and Tukey post hoc tests were performed （α=0.05） to analyze the data. Bond strength was significantly affected by the type of resin cement, and bond strengths of RelyX Unicem and Panavia F2.0 to the fiber posts were significantly higher than the other cement groups. Sandblasting significantly increased the bond strength of DMG group to the fiber posts.