Humid air turbine cycle(HAT)has potential of electrical efficiencies comparable to combined cycle,with lower investment cost and NO_(x) emission.The typical heat exchanger network of HAT consists of intercooler(if the...Humid air turbine cycle(HAT)has potential of electrical efficiencies comparable to combined cycle,with lower investment cost and NO_(x) emission.The typical heat exchanger network of HAT consists of intercooler(if there is),aftercooler,recuperator,economizer and humidifier,which brings higher efficiency but makes the system more complex.To simplify HAT layout,a novel humidifier concept is proposed by integrating the aftercooler into traditional counter-current humidifier.Based on this concept,a one-dimensional model including pressure drop and exergy calculation is established to distinguish the thermodynamic and hydrodynamic characteristics,and then the structural parameters,such as the number of rows and columns,tube diameter,pitch and type for a micro HAT are identified.The results show that the aftercool-humidifier plays the same role as original aftercooler and humidifier,and can match the in-tube air,out-tube air and water stream well with lower volume.In the case of micro HAT cycle,the volume of heat and mass transfer area can be reduced by 47%compared with traditional design.The major thermal resistance occurred in the convection heat transfer process inside the tube;however,using enhanced tube cannot effectively improve the compactness of device.展开更多
The 300 MW steam turbine installed in Waigaoqiao Power Plant with combined HPIP cylinders of double casing structure is a product of the Shanghai Turbine Works utilizing licensed technology. It has a large heat storag...The 300 MW steam turbine installed in Waigaoqiao Power Plant with combined HPIP cylinders of double casing structure is a product of the Shanghai Turbine Works utilizing licensed technology. It has a large heat storage capacity and good thermal insulation, so the metal temperature of first stage of HP cylinder (FSMTI) may reach 400-450℃ after shut down and it takes 7-8 days to cool to 150℃ by natural cooling, Now with a forced cooling system the cooling time may be reduced to 40 hours, so that the turbine may be opened for repair work in about 5-6 days. The cooling system for #2 unit and test procedure are briefly described below.展开更多
This paper implemented cooling configuration design on certain gas turbine HP rotor using parameterized method.It is convenient for complicated gas turbine blade modeling using parameters and also benefit for the geom...This paper implemented cooling configuration design on certain gas turbine HP rotor using parameterized method.It is convenient for complicated gas turbine blade modeling using parameters and also benefit for the geometry modify in later period.Parameterized modeling is the foundation of air cooling turbine blade design method engineering application.Mesh quality can be awarded when generated complicated cooling configuration blade grids,and also the increase of calculation error can arise by many mesh blocks.Film cooling and serpentine passage can effectively enhance the cooling effectiveness and protect blade.展开更多
This paper studied a certain blade with ten radial cooling holes which employed conjugate heat transfer method. The cooling air entered the cooling channel from the bottom of the blade and went out from the top, it wa...This paper studied a certain blade with ten radial cooling holes which employed conjugate heat transfer method. The cooling air entered the cooling channel from the bottom of the blade and went out from the top, it was not ejected into the main flow. This paper used different numerical conditions including different turbulence models,turbulence intensities,thermal conduction coefficients and the influence on fluid property via temperature variation. The temperature distribution and pressure distribution of the blade were compared with experimental data. The results show that the numerical results using different turbulence models are almost identical to experimental data even little deviation occurs at shock wave location. The trends of temperature distribution under different numerical conditions are coincident to experimental data,especially Reynolds stress turbulence model. It can be concluded that anisotropic turbulence models can simulate the transition from laminar to turbulence,and the influence of turbulence intensity on laminar region and transition region is more than that on developed turbulent region.展开更多
Compressors play an important role in day-to-day operation in most oil and gas platforms,especially in the case for maintaining gas pressure in transportation pipe.Its complex problem to detect the sensors health and ...Compressors play an important role in day-to-day operation in most oil and gas platforms,especially in the case for maintaining gas pressure in transportation pipe.Its complex problem to detect the sensors health and abnormality as the sensor reading would reflect the various states of the compressor.In ideal situation,sensor readings offer vast amounts of information on compressor health and could possibly indicate early fault of machines.Furthermore,due to harsh site and process operating conditions,sensors are often found to have drifted or failed,and there is no standard methodology to predict abnormality apart from applying emerging industrial smart sensor technologies.In this paper,we investigate a minimalist approach for detecting abnormality of compressor's shaft's RPM sensor.As the sensors in the compressor are correlated,we first use the outputs of other sensors to predict the shaft's RPM using regression-based models(neural networks and multiple linear regression).Second,we calculate the histogram of residuals by taking the difference between the predicted sensor value and the actual sensor value plus the abnormality in terms of bias/miscalibration and noise.The histogram of residuals can be used for sensor abnormality monitoring.In general,sensor states can be monitored by observing the shifting of the mean in the histogram of residuals.The sensor readings contaminated with noise can be seen by a shifted mean whose value is between the normal condition mean and the biased condition mean.This method is compact and would be relevant to monitor irregularity of the sensors.展开更多
基金financial support by National Science and Technology Major Project(2017-I-0009-0010)to this research work。
文摘Humid air turbine cycle(HAT)has potential of electrical efficiencies comparable to combined cycle,with lower investment cost and NO_(x) emission.The typical heat exchanger network of HAT consists of intercooler(if there is),aftercooler,recuperator,economizer and humidifier,which brings higher efficiency but makes the system more complex.To simplify HAT layout,a novel humidifier concept is proposed by integrating the aftercooler into traditional counter-current humidifier.Based on this concept,a one-dimensional model including pressure drop and exergy calculation is established to distinguish the thermodynamic and hydrodynamic characteristics,and then the structural parameters,such as the number of rows and columns,tube diameter,pitch and type for a micro HAT are identified.The results show that the aftercool-humidifier plays the same role as original aftercooler and humidifier,and can match the in-tube air,out-tube air and water stream well with lower volume.In the case of micro HAT cycle,the volume of heat and mass transfer area can be reduced by 47%compared with traditional design.The major thermal resistance occurred in the convection heat transfer process inside the tube;however,using enhanced tube cannot effectively improve the compactness of device.
文摘The 300 MW steam turbine installed in Waigaoqiao Power Plant with combined HPIP cylinders of double casing structure is a product of the Shanghai Turbine Works utilizing licensed technology. It has a large heat storage capacity and good thermal insulation, so the metal temperature of first stage of HP cylinder (FSMTI) may reach 400-450℃ after shut down and it takes 7-8 days to cool to 150℃ by natural cooling, Now with a forced cooling system the cooling time may be reduced to 40 hours, so that the turbine may be opened for repair work in about 5-6 days. The cooling system for #2 unit and test procedure are briefly described below.
基金Sponsored by the National Natural Science Foundation of China(Grant No. 50476028)
文摘This paper implemented cooling configuration design on certain gas turbine HP rotor using parameterized method.It is convenient for complicated gas turbine blade modeling using parameters and also benefit for the geometry modify in later period.Parameterized modeling is the foundation of air cooling turbine blade design method engineering application.Mesh quality can be awarded when generated complicated cooling configuration blade grids,and also the increase of calculation error can arise by many mesh blocks.Film cooling and serpentine passage can effectively enhance the cooling effectiveness and protect blade.
基金Sponsored by the National Natural Science Foundation of China( Grant No. 50576017)
文摘This paper studied a certain blade with ten radial cooling holes which employed conjugate heat transfer method. The cooling air entered the cooling channel from the bottom of the blade and went out from the top, it was not ejected into the main flow. This paper used different numerical conditions including different turbulence models,turbulence intensities,thermal conduction coefficients and the influence on fluid property via temperature variation. The temperature distribution and pressure distribution of the blade were compared with experimental data. The results show that the numerical results using different turbulence models are almost identical to experimental data even little deviation occurs at shock wave location. The trends of temperature distribution under different numerical conditions are coincident to experimental data,especially Reynolds stress turbulence model. It can be concluded that anisotropic turbulence models can simulate the transition from laminar to turbulence,and the influence of turbulence intensity on laminar region and transition region is more than that on developed turbulent region.
文摘Compressors play an important role in day-to-day operation in most oil and gas platforms,especially in the case for maintaining gas pressure in transportation pipe.Its complex problem to detect the sensors health and abnormality as the sensor reading would reflect the various states of the compressor.In ideal situation,sensor readings offer vast amounts of information on compressor health and could possibly indicate early fault of machines.Furthermore,due to harsh site and process operating conditions,sensors are often found to have drifted or failed,and there is no standard methodology to predict abnormality apart from applying emerging industrial smart sensor technologies.In this paper,we investigate a minimalist approach for detecting abnormality of compressor's shaft's RPM sensor.As the sensors in the compressor are correlated,we first use the outputs of other sensors to predict the shaft's RPM using regression-based models(neural networks and multiple linear regression).Second,we calculate the histogram of residuals by taking the difference between the predicted sensor value and the actual sensor value plus the abnormality in terms of bias/miscalibration and noise.The histogram of residuals can be used for sensor abnormality monitoring.In general,sensor states can be monitored by observing the shifting of the mean in the histogram of residuals.The sensor readings contaminated with noise can be seen by a shifted mean whose value is between the normal condition mean and the biased condition mean.This method is compact and would be relevant to monitor irregularity of the sensors.