Modeling and Optimization of Solar Collector Design for the Improvement of Solar-Air Source Heat Pump Building Heating System

To enhance system stability,solar collectors have been integrated with air-source heat pumps.This integration facilitates the concurrent utilization of solar and air as energy sources for the system,leading to an improvement in the system’s heat generation coefficient,overall efficiency,and stability.In this study,we focus on a residential building located in Lhasa as the target for heating purposes.Initially,we simulate and analyze a solar-air source heat pump combined heating system.Subsequently,while ensuring the system meets user requirements,we examine the influence of solar collector installation angles and collector area on the performance of the solar-air source heat pump dual heating system.Through this analysis,we determine the optimal installation angle and collector area to optimize system performance.

Research on Operation Optimization of Heating System Based on Electric Storage Coupled Solar Energy and Air Source Heat Pump

For heating systems based on electricity storage coupled with solar energy and an air source heat pump(ECSA),choosing the appropriate combination of heat sources according to local conditions is the key to improving economic efficiency.In this paper,four cities in three climatic regions in China were selected,namely Nanjing in the hot summer and cold winter region,Tianjin in the cold region,Shenyang and Harbin in the severe cold winter region.The levelized cost of heat(LCOH)was used as the economic evaluation index,and the energy consumption and emissions of different pollutants were analyzed.TRNSYS software was used to simulate and analyze the system performance.The Hooke-Jeeves optimization algorithm and GenOpt software were used to optimize the system parameters.The results showed that ECSA systemhad an excellent operation effect in cold region and hot summer and cold winter region.Compared with ECS system,the systemenergy consumption,and the emission of different pollutants of ECSA system can be reduced by a maximum of 1.37 times.In cold region,the initial investment in an air source heat pump is higher due to the lower ambient temperature,resulting in an increase in the LOCH value of ECSA system.After the LOCH value of ECSA system in each region was optimized,the heating cost of the system was reduced,but also resulted in an increase in energy consumption and the emission of different pollutant gases.

Development and Experimental Study of Air Source Heat Pump Water Heater

The principle and development prospect of air source heat pump water heat were introduced,as well as the designation of condenser (storage water tank),experimental study on installations was also carried out.The results showed that air source heat pump water heater was superior to conventional system.Under the operation of cooling and heating,heat pump comprehensive utilization equipment could improve heating performance,reduce energy consumption,and recycle condensing heat to provide hot water.

Operating performance of novel reverse-cycle defrosting method based on thermal energy storage for air source heat pump

To solve the fundamental problem of insufficient heat available during defrosting while ensuring the efficient and safe system operation for air-source heat pumps (ASHPs). A novel reverse-cycle defrosting (NRCD) method based on thermal energy storage to eliminate frost off the outdoor coil surface was developed. Comparative experiments using both the stand reverse cycle defrosting (SRCD) method and the NRCD method were carried out on an experimental ASHP unit with a nominal 2.5 kW heating capacity. The results indicate that during defrosting operation, using the NRCD method improves discharge and suction pressures by 0.24 MPa and 0.19 MPa, respectively, shortens defrosting duration by 60%, and reduces the defrosting energy consumption by 48.1% in the experimental environment, compared with those by the use of SRCD method. Therefore, using the NRCD method can shorten the defrosting duration, improve the indoor thermal comfort, and reduce the defrosting energy consumption in defrosting.

Operation Performance of Air Source Heat Pump System for Space Heating in Tianjin

An air source heat pump system (ASHPS) used in an office building is set up and studied experimentally. Its operating performance in winter is evaluated based on test data and a comparative discussion is given on the effect of climate conditions and heating load ratio on the operation behavior. Then heating capacity variation caused by evaporator frosting is analyzed as well. Finally, the defrosting parameters and the technical feasibility are studied for a constant heating demand. The experimental results indicate that both the outlet water temperature drop and the system COP should be taken into account when setting defrosting parameters, and ASHPS is a viable technology for space heating and hot-water production in winter in Tianjin, which can maintain the room temperature above 19 ℃ when the outdoor temperature is -2 ℃.

Refrigerant Control Strategies for Residential Air-Conditioning and Heat-Pump System

This paper simulated the optimal refrigerant charge inventory of a refrigeration system in air-conditioning operation and heat-pump operation respectively,and studied the refrigerant control strategies in this system.The void fraction in two-phase fluid region was calculated by Harms model.And based on distributed parameter model and Harms model,the refrigerant charge inventory in condenser and evaporator were calculated and analyzed in air-conditioning conditions and heat-pump conditions,respectively.The calculating results of different refrigerant mass between refrigeration and heating conditions indicate that the optimal refrigerant charge inventory in heat-pump conditions is lower than that in air-conditioning conditions.To avoid the decrease of COP due to the surplus refrigerant in heating conditions,we introduced the liquid reservoir control method and associate capillary control method.Both of them could increase the heating capacity of the air-source heat pump.The difference of optimal refrigerant charge inventory in air-conditioning and heat-pump system can be controlled by the liquid reservoir or the associate capillary.

Performance and Optimization of Air Source Heat Pump Water Heater with Cyclic Heating

A new type of microchannel condenser applied in the air source heat pump water heater(ASHPWH)with cyclic heating was proposed in this study.The operating performance of the ASHPWH was frst tested.Then,the structure of the microchannel condenser was optimized with the implement of vortex generators.Finally,a numerical model of the ASHPWH was established and the optimized microchannel condenser was studied.The experimental results showed that the average coefficient of performance(COP)of the 1HP(735 W)ASHPWH reached 3.48.In addition,the optimized microchannel condenser could be matched with a 3 HP(2430W)ASHPWH with an average heating capacity of 10.30 kW,and achieving an average COP of 4.24,14.6%higher than the limit value in the national standard.

太阳能-空气源热泵牧草干燥系统制热性能研究

以太阳能-空气源热泵牧草干燥系统为研究对象,通过系统不同工作模式的温升、恒温制热试验及带载试验,分析了温升速率、单位温升能耗、COP及除湿效率。研究结果表明:联合制热模式与太阳能单独制热相比,单位温升耗电量降低了86.2%,温升速率提高了99~112倍。联合制热模式与热泵单独制热试验相比,在温升过程中温升速率降低了7.7%~17.6%,单位温升耗电量降低8.0%;在恒温制热过程中,前者COP比后者提高了6.5%~11.1%,耗电量降低了5.8%~10.7%;在升温制热过程中前者COP比后者提高了6.0%~10.4%,耗电量降低了6.6%~11.1%。联合干燥模式比热泵单独干燥模式的SMER值高19.8%~36.2%。

光伏光热联合双源热泵系统运行模式研究(1):最佳切换模式验证

讨论了光伏光热联合双源热泵系统制热运行的最佳切换模式。利用TRNSYS软件建立了仿真模型,对双源(水源、空气源)热泵系统性能系数(COP_(s))进行了计算,提出以某时刻空气源热泵模式或水源热泵模式运行COP_(s)较大者优先运行作为COP_(s)切换模式。通过前期实验结果验证了模拟结果的正确性,并与常规的集热水箱温度切换模式进行了对比实验,验证了COP_(s)切换模式的有效性。结果表明,该实验系统以COP_(s)最佳切换模式运行时发电量和发电效率较集热水箱温度切换模式分别提高了5.35%和1.73%,耗电量降低了17.03%,COP_(s)提高了4.91%。

光伏光热联合双源热泵系统运行模式研究(2):供暖季系统仿真研究

使用TRNSYS软件建立了光伏光热-双源热泵(PV/T-DSHP)系统的仿真模型。选取夏热冬冷地区某一近零能耗居住建筑作为研究对象,模拟研究了供暖季PV/T-DSHP系统在COP_(s)切换模式下的运行特性和能耗。结果表明:平均光电效率为15.08%,平均光热效率为33.05%;水源热泵运行模式下供暖季平均COP为4.55,空气源热泵运行模式下供暖季平均COP为3.19,PV/T-DSHP系统的平均COP_(s)为2.98;供暖季系统自满足率为61%。

基于ANFIS的太阳能-空气源热泵供暖系统温度控制研究

针对太阳能-空气源热泵供暖系统运行环境复杂多变,模糊控制器的设计高度依赖人工经验的问题,提出一种基于自适应神经模糊推理系统(ANFIS)改进的模糊控制方法。该方法利用ANFIS在复杂系统建模中的优势,结合供暖系统温度响应特性和实际运行数据,建立联合供暖系统变工况ANFIS模型,生成与系统性能适配的模糊规则库并传递给模糊控制器执行。Matlab/Simulink仿真对比试验表明,与单一的模糊控制相比,该方法的控制精度提高了17.65%,调节时间缩短了36.4%,具有更高的控制精度和响应速度。

严寒地区空气源热泵耦合电磁能系统模拟运行研究

目的 为了促进空气源热泵耦合电磁能供热系统在严寒地区住宅建筑中的应用,研究该系统的运行性能和稳定性。方法 以沈阳地区某住宅建筑为例,应用Trnsys软件建立了空气源热泵耦合电磁能供热系统仿真模型,并用实测值对模型进行了验证;深入探讨空气源热泵耦合电磁能供热系统在供热期的运行特点,并与空气源热泵和电磁能供热系统分别进行比较。结果 空气源热泵耦合电磁能供热系统模型可靠,相对误差可以控制在15%以内;在供热期,室内平均温度可保持在17.97~21.84℃;空气源热泵耦合电磁能供热系统比电磁能供热系统的COP提高了59.17%,空气源热泵耦合电磁能供热系统CO_(2)减排量比空气源热泵和电磁能供热系统分别提高1.47%和59.50%。结论 空气源热泵耦合电磁能供热系统运行和COP变化更为稳定,系统环境效益更佳,室内热舒适性更高。

超低温空气源热泵与太阳能供热系统在寒冷地区的优化应用

为了加强对环境的保护,推动可持续发展社会的建设,超低温空气源热泵联合太阳能供热系统被研发出来。该联合系统的应用极大地缓解了当前能源紧张的问题,同时对降低环境污染、提高能源利用率、降低供暖成本也有着积极的作用。基于此,围绕超低温空气热源泵与太阳能供热系统展开论述,对当前超低温空气源热泵与太阳能联合供热系统结构进行分析,剖析其中所存在的问题,同时针对问题提出超低温空气源热泵与太阳能供热系统的优化方案,将其应用于北方寒冷地区的一建筑当中,并对应用效果进行分析。

一种考虑光伏发电与峰谷电价的空气源热泵最优装机容量计算方法

针对目前光伏发电及峰谷电价的用电形式下,空气源热泵耦合电锅炉供热系统经济性装机容量选择困难的有关问题,提出一种综合考虑光伏发电与峰谷电价影响的设备装机容量计算方法,使用空气源热泵最优不保证天数(OGD)作为选型参考值,通过TRNSYS建立系统模型开发新模块使其具有自动寻优能力。在使用测试数据验证模型准确性后,基于该模型计算5座代表性城市OGD推荐值。结果表明:OGD值受建筑负荷大小与光伏装机容量双重影响。采用OGD均值作为推荐值时,单一建筑OGD与均值分别对应的费用年值最大误差为8.17%,可保证计算准确性;5类气候分区内各城市费用年值变化规律基本一致,OGD值随气候变暖各气候分区间平均下降46.83%;其中北京市最大OGD值仅为5,说明在寒冷B区城市此类系统添加光伏发电后,可不设置辅助热源。

太阳能光热光电技术在高校宿舍的对比研究

针对夏热冬冷地区某高校宿舍用能特征,基于太阳能的两种利用方式分别设计了太阳能光热供能系统和太阳能光电供能系统。利用TRNSYS仿真软件模拟两种供能系统的运行特性,对比了两种系统的组件性能、经济性及减排量。结果表明:除假期时间外,太阳能集热单元的集热效率保持在40%左右,年太阳能保证率可达58%;并网光伏发电单元全年发电量为311 394 kW·h,发电量自用率达到70.5%。太阳能光电供能系统的年能耗费用较光热供能系统节省11万元,费用年值减少4.9万元,年碳排放量降低166 t。对光伏安装面积进行优化后可知,光伏安装面积每增加52 m^(2),光伏供能系统费用年值减少2111元。研究结果可为高校宿舍建筑选择适宜的太阳能利用形式提供参考和依据。

补气增焓准二级压缩空气源热泵理论最佳除霜量研究

为解决能源浪费的问题,通过引入相关结霜模型进行理论分析,结合实验数据得出“理论最佳除霜量”的半经验公式。为验证该公式有效性,针对某厂家的补气增焓准二级压缩空气源热泵进行不同工况下:空气相对湿度65%、70%、80%,对应的空气干球温度-4~4℃的温度区间的实验测试。通过测试不同状态下的实际除霜量与“理论最佳除霜量”的半经验公式计算的理论除霜量进行比较,发现两者相对误差较小,保持在±10%以内,该公式对霜层后期的预测值较为准确,可作为设计补气增焓准二级压缩能够空气源热泵融霜时间控制的基准。

具有防融霜装置的蒸发器结霜特性及性能仿真研究

以具有防融霜装置的蒸发器为研究对象,建立基于理想最小防融霜补热量和结霜量无量纲关联式的空气源热泵动态模型,并依据实验数据验证其精确性,通过数值模拟分析不同环境参数对具有防融霜装置的蒸发器性能的影响。结果表明:后置式与跨越式系统蒸发器换热系数要高于前置式与传统电辅热系统,霜层厚度更小,分布更均匀;当相对湿度一定时,蒸发器换热系数随温度升高而增大;当空气温度不变时,换热系数随相对湿度的下降而减小,霜层更均匀;温度对蒸发器换热系数的影响比相对湿度更大。

太阳能空气源热泵耦合相变蓄热器供热系统模拟研究

目的为提高可再生能源利用率,研究太阳能空气源热泵耦合相变蓄热器供热系统实际性能,建立适合夏热冬冷地区民用住宅的节能供热系统。方法利用TRNSYS软件建立太阳能空气源热泵耦合相变蓄热器供热系统模型,并与太阳能空气源热泵供热系统进行对比分析,对两个系统从制热量、耗电量、能效比以及室内人体热舒适度四个方面进行模拟分析,使用PMV-PPD评价方法对两个系统的室内热舒适度进行评价。结果耦合相变蓄热器的供热系统耗电量低于无相变供热系统,节能率提高了13.29%;耦合相变蓄热器的供热系统平均能效比为3.5,太阳能空气源热泵供热系统的平均能效比为3.32,提高了5.14%;耦合供热系统可以为人体提供I级室内热环境水平的热舒适度,无相变供热系统只能为人体提供II级。结论太阳能空气源热泵耦合相变蓄热器供热系统节能性更好,系统能效更高,提高了可再生能源利用率,并且耦合供热系统在热舒适性方面优于无相变供热系统。

考虑空气源热泵负荷聚合参与的需求响应

基于“电网-聚合商-负荷”三级架构,提出空气源热泵负荷聚合参与需求响应的控制策略。供暖运营商作为热泵负荷的聚合商,在保证用户热舒适度的基础上,利用建筑本身的蓄能能力,结合分时电价最小化供热成本,并对负荷可调节潜力进行评估。当电网调度部门下发调控指令后,考虑用户舒适度和电网调节需求,基于多目标遗传算法分配各负荷调节量,在满足调控目标的同时可改善调控带来的聚合功率振荡、反弹负荷大等问题。最后,仿真验证所提策略的有效性。

基于正交试验法的太阳能复合热水系统优化

为降低生活热水能耗,实现空气源热泵辅助太阳能供热水系统的高效节能运行,选取济南市某高校学生宿舍空气源热泵辅助太阳能供热水系统作为研究对象,利用瞬时系统模拟软件搭建了系统仿真模型,并采用无交互作用的正交试验法,分别以全年系统性能系数和太阳能保证率为优化目标,优化了太阳能集热器面积、集热器倾角、热泵制热功率及水箱容积,并分析其结果的经济性和节能性。结果表明:当以系统性能系数为优化目标时,最优组合中集热器面积为390 m^(2)、集热器倾角为42°、热泵制热功率为50 kW、水箱容积为23.94 m3,而动态费用年值为7.38万元,较天然气系统年节省标煤为17.12 tce;当以太阳能保证率为优化目标时,最优组合中集热器面积为342 m^(2)、集热器倾角为44°、热泵制热功率为35.5 kW、水箱容积为20.58 m3,而动态费用年值为6.56万元,较天然气系统年节省标煤为16.63 tce。