Evaluation of the Oxidation Reactivity and Behavior of Exhaust Soot Particles from Diesel Engines with Different Emission Levels

The aim of this study was to investigate the oxidation reactivity and behavior of exhaust particulate matter(PM)from diesel engines.PM samples from two diesel engines(1K,CY4102)with different emission levels were collected by a thermophoretic system and a quartz filter.The oxidation reactivity,oxidation behaviors,and physicochemical properties of the PM samples were analyzed using thermogravimetric analysis(TGA),high-resolution transmission electron microscopy(HRTEM),Fourier-transform infrared spectrometry(FTIR),and Raman spectroscopy.The results showed that there was a great difference in the oxidation reactivity of soot particles emitted by the two different diesel engines.A qualitative analysis of the factors influencing oxidation reactivity showed that the nanostructure,degree of graphitization,and relative concentration of aliphatic C—H functional groups were the most important factors,whereas no significant correlation was found between the primary particle size and activation energy of the diesel soot.Based on the oxidation behavior analysis,the diesel soot particles exhibited both internal and surface oxidation modes during the oxidation process.Surface oxidation was dominant during the initial stage,and as oxidation progressed,the mode gradually changed to internal oxidation.Internal oxidation mode of soot particles from the 1K engine was significantly higher than that of CY4102.

Performance, Combustion and Emission Characteristics of Oxygenated Diesel in DI Engines: A Critical Review

The transition from non-renewable to renewable energy sources is a significant challenge of our time. In the fuel industry, oxygenated additives such as butanol are transforming conventional fuels into renewable biofuels. This technology has been utilized in reciprocating engines for decades. This paper reviews the viability of using an n-butanol blend as a short-term replacement for diesel by analyzing its physical and chemical properties, combustion, performance, and emission characteristics in compression ignition (CI) engines under various conditions, including variable load, speed, acceleration, and both stationary and transient cycles. N-Butanol exhibits higher viscosity, better lubricity, higher heating value, improved blend stability, enhanced cold-flow properties, and higher density. These factors influence spray formation, injection timing, atomization, and combustion characteristics. Its higher oxygen content improves the diffusion combustion stage and efficiency. Adding 5% and 10% n-butanol to diesel increases pressure and apparent heat release rate, slightly reduces temperature, and improves thermal efficiency, with mixed effects on CO and THC emissions and a notable decrease in particulate matter emissions. Fuel consumption increases, while the impact on NOx emissions varies. A 10% butanol blend is considered optimal for enhancing performance and reducing particulate emissions without significantly affecting NOx emissions. Blending up to 40% butanol with diesel does not require engine modifications or ECU recalibrations in engines calibrated for pure diesel. Due to its advantageous properties and performance, n-butanol is recommended as a superior alcohol-diesel blend than ethanol for short-term diesel replacement.

Comparative Study of Exhaust Emissions from Diesel and Syngas Powered 3.5 kW Compression Ignition Engine with and without Load

Despite diesel engines being highly efficient, with low fuel consumption and reduced carbon dioxide emissions, they emit relatively high levels of particulate matter and oxides of nitrogen (NOx) due to high exhaust gas temperatures. Engine emissions show the quality and completeness of combustion. This paper aims to present the results of a study comparing exhaust emissions from a diesel and syngas powered engine. Syngas was produced from co-firing coal and biomass in a gasifier then cleaned, cooled and applied as an alternative fuel in an engine operated from 0 - 100% load. Exhaust-emissions were monitored at this load conditions. The exhaust-temperature was measured using thermocouples and the emission gases were analyzed using Testo 350. The emissions were lower and decreased as the engine load increased, except for sulphur dioxide and NOx. The study shows that levels of carbon monoxide, were higher in a range of 46.5 - 80.2%, while carbon dioxide was 3.3 - 18% higher compared to those from diesel. Hydrocarbon emissions were 480 and 1250 ppm for diesel and syngas respectively. The study reveals that the engine operates optimally at higher loads since hydrocarbons and oxides of carbon are low due to complete combustion at higher temperatures. Exhaust gas temperature was higher in the syngas fuel and increased as the engine load increased in the range of 455.83 - 480.03˚C which influenced the formation of NOx. NOx from diesel was found to be higher, ranging from 32.5 - 40.5%, compared to those from syngas with an engine load of 75%. The study observed that relative to diesel, the emissions of sulfur dioxide at 50% engine load were lower in a range of 23.7 - 57.1%. Emissions of hydrocarbons depended on the degree of substitution of diesel and engine load. The study therefore shows that, relative to diesel, emissions decreased when syngas was used with upgraded syngas from Prosporis juliflora presenting as the best alternative followed by Hyphanae compressa, and lastly rice husk. For optimal performance of the syngas fuelled engine, the study reports that the engine should be operated at engine loads above 50% with strategies on NOx emissions considered.

Analysis of the Emissions and Performance of a Diesel Engine Using Pumpkin Seed Oil Methyl Ester with Different Injection Pressures

Biodiesel fuel is a potential alternative energy source for diesel engines due to its physiochemical characteristics relatively similar to those of traditional diesel fuel.In this study,the performance,emission,and combustion features of a mono cylinder DI diesel engine are assessed using 20%Pumpkin seed methyl ester(PSOME20)and considering varying injection pressures(200,220,240,and 260 bar).The considered Pumpkin seed oil is converted into pumpkin biodiesel by transesterification and then used as fuel.The findings demonstrate that the Brake Thermal Efficiency(BTE)of PSOME20 can be raised by 1.68%,and the carbon monoxide(CO),hydrocarbon(HC),and smoke emanations can be lowered,while oxides of nitrogen(NOx)emissions are increased at an injection pressure(IP)of 240 bar compared to the standard IP of 200 bar.The cylinder pressure and the Heat Release Rate(HRR)become higher at 240 bar,whereas the ignition delay is shortened with respect to PSOME20 at a normal IP of 200 bar.

Influence of Urea Uneven Injection on the Performances of a Diesel Engine

The influence of heterogeneous flow injection of urea at different velocities and temperatures on NO x conversion efficiency,ammonia storage and ammonia leakage is investigated experimentally.A diesel engine employing a selective catalytic reduction(SCR)technology is considered.It is found that for a fixed injection velocity,the degree of ammonia leakage changes depending on the temperature.The higher the temperature,the faster the catalytic reduction reaction and the smaller the degree of ammonia leakage.The temperature has a great influence on the catalytic reduction reaction rate.At an injection velocity of 10000/h,the average reaction rate at 420℃ is 12 times higher than that at 180℃.The injection velocity has a weak influence on the reaction rate.When the injection velocity changes from 10000/h to 40000/h at the same temperature,the average reaction rate does not change appreciably.However,increasing the space velocity can accelerate the leakage of ammonia,thereby miti-gating the benefits associated with the NO_(x) conversion.

A Strategy to Control the Turbocharger Energy of a Diesel Engine at Different Altitudes

Power deterioration is a major problem for diesel engines operating at high altitudes.This problem stems from the limited availability of turbocharger energy,which is not enough to increase the boost pressure to the required level.In this study,a control strategy is introduced in order to achieve engine power recovery at different altitudes.It is shown that as the altitude increases from 0 to 4500 m,the required boost pressure ratio increases from 2.4 to 4.3.The needed turbocharger energy should be increased accordingly by 240%,and the TCC(turbine characterization coefficient)should be adjusted within wide ranges.A 12%decrease in the TCC can lead to a rise of the intake air pressure,which can compensate the pressure decrease due to a 1000 m altitude increase.The fluctuation range of boost pressure was within 14.5 kPa for variations in altitude from 0 to 4500 m.

Investigating the Effects of Eichhornia Crassipes Biodiesel and Liquefied Petroleum Gas on the Performance and Emissions of a Dual-Fuel Engine

This study considers the effect of Eichhornia Crassipes Biodiesel(ECB)blends on the performances,combustion,and emission characteristics of a direct injection compression ignition engine operated in a dual-fuel mode(DFM)and equipped with an Exhaust gas recirculation technique(EGR).In particular,a single-cylinder,four-stroke,water-cooled diesel engine was utilized and four modes of fuel operation were considered:mode I,the engine operated with an ordinary diesel fuel;mode II,the engine operated with the addition of 2.4 L/min of lique-fied petroleum gas(LPG)and 20%EGR;mode III,20%ECB with 2.4 L/min LPG and 20%EGR;mode IV,40%ECB with 2.4 L/min LPG and 20%EGR.The operation conditions were constant engine speed(1500 rpm),var-iation of load(25%,50%,75%,and 100%),full load,with a compression ratio of 18,and a time injection of 23°BTDC(Before top died center).With regard to engine emissions,carbon dioxide(CO_(2)),carbon monoxide(CO),hydrocarbons(UHC),and nitrogen oxide(NOX)were measured using a gas analyzer.The smoke opacity was measured using an OPABOX smoke meter.By comparing the results related to the different modes with mode I at full load,the BTE(Brake thermal efficiency)increased by 20.17%,11.45%,and 12.66%with modes II,III,and IV,respectively.In comparison to the results for mode II,the BTE decreased due to the combustion of ECB blends by 7.26%and 6.24%for mode III and mode IV,respectively,at full load.In comparison to mode II,the Brake specific energy consumption(BSEC)increased with the ECB substitution.With ECB blends,there is a noticeable decrease in the CO,CO_(2),and UHC emissions at a partial load.Furthermore,the 20%ECB has no effect on CO emissions at full load.For modes II and IV,the CO_(2)increased by 33.33%and 19%,respectively,while the UHC emissions were reduced by 14.49%for mode III and 26.08%for mode IV.The smoke of mode III was lower by 7.21%,but for mode IV,it was higher by 12.37%.In addition,with mode III and mode IV,the NOx emissions increased by 30.50%and 18.80%,respectively.

Test Research on the Knock of a Common-Rail Diesel Engine Fueled with Diesel-Methanol Dual-Fuel

Experiments were conducted on a diesel-methanol dual-fuel(DMDF)engine modified by a six-cylinder,turbocharged,inter-cooled diesel engine.According to the number of diesel injection,the experiments are divided to two parts:the single injectionmode and double injectionmode.The results show that,at the double injectionmode,themaximumof pressure rise rate is small and the engine runs smoothly,however,knock still occurswhen the cocombustion ratio(CCR)is big enough.Under knock status,the power density of the block vibration concentrating at some special frequencies rises dramatically,and the special frequency of single injection mode(about 4.1 kHz)is lower than that of double injection mode(7–9 kHz).The cylinder pressure oscillations of knock status are very different fromthe non-knock status.Under knock status,cylinder pressure oscillations become more concentrated and fiercer at some special frequencies,and the same as the block vibration.The special frequency of single injection mode(3–6 kHz)is lower than that of double injection mode(above 9 kHz).

Experiment Study on the Exhaust-Gas Heat Exchanger for Small and Medium-Sized Marine Diesel Engine

This paper aims to design a special exchanger to recover the exhaust gas heat of marine diesel engines used in small and medium-sized fishing vessels,which can then be used to heat water up to 55°C–85°C for membrane desalination devices to produce fresh water.A new exhaust-gas heat exchanger of fins and tube,with a reinforced heat transfer tube section,unequal spacing fins,a mixing zone between the fin groups and four routes tube bundle,was designed.Numerical simulations were also used to provide reference information for structural design.Experiments were carried out for exhaust gas waste heat recovery from a marine diesel engine in an engine test bench utilizing the heat exchanger.The experimental results show that the difference between heat absorption by water and heat reduction of exhaust gas is less than 6.5%.After the water flow rate was adjusted,the exhaust gas waste heat recovery efficiency was higher than 70%,and the exhaust-gas heat exchanger’s outlet water temperature was 55°C–85°C at different engine loads.This means that the heat recovery from the exhaust gas of a marine diesel engine meets the requirement to drive a membrane desalination device to produce fresh water for fishers working in small and medium-sized fishing vessels.

Effect of Palm Oil Biodiesel Blends on Engine Emission and Performance Characteristics in an Internal Combustion Engine

Increasing global environmental issues and depleting fossil fuel reserves has necessitated the need for alternative and sustainable fuel. In this paper, the effects of biodiesel and its blend on engine emission and performance characteristics in an internal combustion engine were analyzed. Biodiesel derived from the transesterification of raw palm oil was blended with diesel fuel at different proportions designated as PO5 (5% Biodiesel and 95% Diesel), PO10 (10% Biodiesel and 90% Diesel), PO15 (15% Biodiesel and 85% Diesel), PO20 (20% Biodiesel and 80% Diesel), PO50 (50% Biodiesel and 50% Diesel), PO85 (85% Biodiesel and 15% Diesel), and PO100 (100% Biodiesel). A Lombardini 2-cylinder, four-stroke direct injection diesel engine with a compression ratio of 22.8 was developed using Ricardo Wave software in which diesel, palm oil biodiesel blends and pure biodiesel are used in the model, and the obtained results were analysed and presented. The simulation was done under varying engine speeds of 1200 rpm to 3200 rpm at full load condition. Biodiesel and its blends are more environment-friendly and non-toxic when compared to diesel fuel;it also improves the mechanical efficiency of the engines, and above all can also lead to a reduction in poverty among rural dwellers. The obtained results showed that brake specific fuel consumption and brake thermal efficiency increased with palm oil biodiesel blends as compared to diesel fuel which might be a result of biodiesel’s lower heating value, and the increase in thermal energy may be a result of the oxygenation of the biodiesel blend as compared to pure diesel. In terms of brake torque, palm oil biodiesel blends were lesser than diesel fuel. The CO, HC, and NOx emissions of palm oil biodiesel blends decreased significantly compared to that of pure diesel. From this study, palm oil biodiesel emits lesser emissions than diesel fuel and its performance characteristics are similar to diesel fuel. Therefore, palm oil biodiesel can be used without any modifications directly in a diesel engine. In addition, it can also be used as blends as an alternative and sustainable fuel, decreasing air pollution, and increasing environmental sustainability.

Investigation of Mechanical Stresses for Cylinder Head of High Power Diesel Engine

Aim To ivestigate the influence on the cylinder head's stress distribution and value caused by its structure's changes.Methods Three types of cylinder heads of high power diesel engines were analysed with finite element method using I-DEAS Master series software.The actual condition of the cylinder head was simulated with different kinds of elements.Tempera- ture method was used to exert the predeformation of the bolts to the finite element model,so the pretightening force was discribed accurately Results Stress distribution regularities of the cylinder head under different working conditions were taken On the basis,the analysing results ofthreeof design schemes were compared and the optimum structure was taken Conclusion Transition condition between the head plate and the standing board ,shape of the head plate and the jobbing sheet,etc will affect the cylinder head's bearing condition

Study of Diesel Engine Management System

Aim To study the diesel engine management spstem (DEMS). The DEMS can consider many engine parameters and so it can acquire the optimum system performance. Methods On the basis of analyzing the characteristics of diesel engine electronic system, the real-time, multi-tasks system design methods were used for the heavy duty vehicular diesel engine electronic control system . The hardware and software of DEMS were developed. Results and Conalusion By the test on dieSel engine bed, the system was verified and the foundation of the fully developed DEMS was laid.

Math Imitation of the Texture of Particle Cluster Emitted from Diesel Engine

Aim The particle texture from diesel engine was imitated by use of computer. Methods The theory of fractal geometry and the diffusion limited aggregation model were used to simulate the micron texture. Results The fractal dimensions of granule distribution and corpuscle superficial area are quite conformed with those of measurement. Conclusion The texture parameters of engine particle cluster can be obtained precisely by use of fractal theory.

CAD System for Cylinder Head Used in High-Speed and Heavy-Power Diesel Engine

A CAD system for the cylinder head is developed. As an integrated system, it can be used in 3 D modeling, 2 D drawing and finite element structural analysis and optimization. The key problems in system designing are introduced. Design flow, system structure and how to solve the key problems are focused on. All of those would form the base for more research on how to use the modern CAD technology to design complex engine parts. And it is also a good example of using the modern CAD technology.

Speed Disturbance in the Diesel Engine Electronic Control System

In order to sample the speed signal of electronic diesel engine in real time and make the engine work reliable, the diesel engine control system's speed acquisition was studied and the problem of speed disturbance was solved. The control system was based on the 8?bit electronic control unit(ECU) system and the assembly language was used to design the software for controlling the engine fuel quantity and the turbocharger of the variable geometry turbine for the heavy duty diesel engine. By changing the timing method for speed acquisition, the problem of speed disturbance was solved and the reliability of the ECU was improved.

Excavator Energy-saving Efficiency Based on Diesel Engine Cylinder Deactivation Technology

The hydraulic excavator energy-saving research mainly embodies the following three measures： to improve the performance of diesel engine and hydraulic component, to improve the hydraulic system, and to improve the power matching of diesel-hydraulic system-actuator. Although the above measures have certain energy-saving effect, but because the hydraulic excavator load changes frequently and fluctuates dramatically, so the diesel engine often works in high-speed and light load condition, and the fuel consumption is higher. Therefore, in order to improve the economy of diesel engine in light load, and reduce the fuel consumption of hydraulic excavator, energy management concept is proposed based on diesel engine cylinder deactivation technology. By comparing the universal characteristic under diesel normal and deactivated cylinder condition, the mechanism that fuel consumption can be reduced significantly by adopting cylinder deactivation technology under part of loads condition can be clarified. The simulation models for hydraulic system and diesel engine are established by using AMESim software, and fuel combustion consumption by using cylinder-deactivation-technology is studied through digital simulation approach. In this way, the zone of cylinder deactivation is specified. The testing system for the excavator with this technology is set up based on simulated results, and the results show that the diesel engine can still work at high efficiency with part of loads after adopting this technology; fuel consumption is dropped down to 11% and 13% under economic and heavy-load mode respectively under the condition of driving requirements. The research provides references to the energy-saving study of the hydraulic excavators.

Diesel Engine Valve Clearance Fault Diagnosis Based on Features Extraction Techniques and FastICA-SVM

Numerous vibration-based techniques are rarely used in diesel engines fault diagnosis in a direct way, due to the surface vibration signals of diesel engines with the complex non-stationary and nonlinear time-varying fea- tures. To investigate the fault diagnosis of diesel engines, fractal correlation dimension, wavelet energy and entropy as features reflecting the diesel engine fault fractal and energy characteristics are extracted from the decomposed signals through analyzing vibration acceleration signals derived from the cylinder head in seven different states of valve train. An intelligent fault detector FastICA-SVM is applied for diesel engine fault diagnosis and classification. The results demonstrate that FastlCA-SVM achieves higher classification accuracy and makes better general- ization performance in small samples recognition. Besides, the fractal correlation dimension and wavelet energy and entropy as the special features of diesel engine vibration signal are considered as input vectors of classifier FastlCA- SVM and could produce the excellent classification results. The proposed methodology improves the accuracy of fea- ture extraction and the fault diagnosis of diesel engines.

Combination of biodiesel-ethanol-diesel fuel blend and SCR catalyst assembly to reduce emissions from a heavy-duty diesel engine

In this study, the efforts to reduce NOx and particulate matter （PM） emissions from a diesel engine using both ethanol-selective catalytic reduction （SCR） of NOx over an Ag/Al2O3 catalyst and a biodiesel-ethanol-diesel fuel blend （BE-diesel） on an engine bench test are discussed. Compared with diesel fuel, use of BE-diesel increased PM emissions by 14% due to the increase in the soluble organic fraction （SOF） of PM, but it greatly reduced the Bosch smoke number by 60%-80% according to the results from 13-mode test of European Stationary Cycle （ESC） test. The SCR catalyst was effective in NOx reduction by ethanol, and the NOx conversion was approximately 73%. Total hydrocarbons （THC） and CO emissions increased significantly during the SCR of NOx process. Two diesel oxidation catalyst （DOC） assemblies were used after Ag/Al2O3 converter to remove CO and HC. Different oxidation catalyst showed opposite effect on PM emission. The PM composition analysis revealed that the net effect of oxidation catalyst on total PM was an integrative effect on SOF reduction and sulfate formation of PM. The engine bench test results indicated that the combination of BE-diesel and a SCR catalyst assembly could provide benefits for NOx and PM emissions control even without using diesel particle filters （DPFs）.

Engineering property test of kaolin clay contaminated by diesel oil

Engineering property of kaolin clay contaminated by diesel oil was studied through a series of laboratory experiments.Oil contents(mass fraction) of 4%,8%,12%,16% and 20% were selected to represent different contamination degrees,and the soil specimens were manually prepared through mixing and static compaction method.Initial water content and dry density of the test kaolin clay were controlled at 10% and 1.58 g/cm^3,respectively.Test results indicate that since part of the diesel oil will be released from soil by evaporation,the real water content should be derived through calibration of the quasi water content obtained by traditional test method.As contamination degree of the kaolin clay increases,both liquid limit and plastic limit decrease,but there's only a slight increase for plasticity index.Swelling pressure of contaminated kaolin clay under confined condition will be lowered when oil-content gets higher.Unconfined compressive strength(UCS) of the oil-contaminated kaolin clay is influenced by not only oil content but also curing period.Increase of contamination degree will continually lower UCS of the kaolin clay specimen.In addition,electrical resistivity of the contaminated kaolin clay with given water content decreases with the increase of oil content.However,soil resistivity is in good relationship with oil content and UCS.Finally,oil content of 8% is found to be a critical value for engineering property of kaolin clay to transit from water-dominated towards oil-dominated characteristics.

Study on Effects of Diesel Engine Cooling System Parameters on Water Temperature

A simulation model for a certain diesel engine cooling system is set up by using GT-COOL. The backwater temperature response in different operating conditions is simulated numerically. The effects of single or multiple system parameters on the water temperature are analyzed. The results show that, changing different single parameters, the time taken for the steady backwater temperature is different, but relatively short;and if multiple parameters are changed, the time will be longer. Referred to the thermal balance test, the simulation results are validated and provide a basis for the intelligent control of the cooling system.