Effect of Sr modification on microstructure and thermal conductivity of hypoeutectic Al−Si alloys

Trace amount of Sr(0.05 wt.%)was added into the hypoeutectic Al−Si(3−12 wt.%Si)alloys to modify their microstructure and improve thermal conductivity.The results showed that the thermal conductivity of hypoeutectic Al−Si alloys was improved by Sr modification,and the increment and increasing rate of the thermal conductivity gradually increased with Si content increasing.The improvement of thermal conductivity was primarily related to the morphology variation of eutectic Si phases.In Sr-modified Al−Si alloys,the morphology of eutectic Si phases was a mixed morphology of fiber structure and fine flaky structure,and the proportion of the fine flaky eutectic Si phases gradually decreased with Si content increasing.Under the Si content reaching 9 wt.%,the proportion of fine flaky eutectic Si phases was nearly negligible in Sr-modified alloys.Correspondingly,the increment and increasing rate of thermal conductivity of Sr-modified alloys reached the maximum and tended to be stable.

Mechanical and thermo-physical properties of rapidly solidified Al-50Si-Cu(Mg) alloys for thermal management application

Al-high Si alloys were designed by the addition of Cu or Mg alloying elements to improve the mechanical properties. It is found that the addition of 1 wt.% Cu or 1 wt.% Mg as strengthening elements significantly improves the tensile strength by 27.2% and 24.5%, respectively. This phenomenon is attributed to the formation of uniformly dispersed fine particles(Al2Cu and Mg2Si secondary phases) in the Al matrix during hot press sintering of the rapidly solidified(gas atomization) powder. The thermal conductivity of the Al-50 Si alloys is reduced with the addition of Cu or Mg, by only 7.3% and 6.8%, respectively. Therefore, the strength of the Al-50 Si alloys is enhanced while maintaining their excellent thermo-physical properties by adding 1% Cu(Mg).

Microstructure and mechanical properties of friction stir processed Al−Mg2Si alloys

The microstructure and mechanical properties of friction stir processed Al−Mg2Si alloys were studied by TEM and EBSD.The results showed that an increase in the tool rotation speed(300−700 r/min)led to a decrease in the defect area(from 10.5 mm2 to zero),whereas the defect area demonstrated the opposite trend(increased to 1.5 mm2 from zero)upon further increasing the rotation speed(700−1200 r/min).The types of defects were transformed from tunnel defects to fusion defects as the rotational speed increased.The coarse Mg2Si dendrites were broken and fine particles(smaller than 10mm)formed in the weld nugget(WN).The amount of low-angle grain boundaries increased significantly from 57.7%to 83.6%,which was caused by an increase in the content of the deformed structure(from 1.7%to 13.6%).The hardness,ultimate tensile strength(UTS)and elongation were all greatly improved for the weld nugget.The hardness values of the WNs had the following order:R300<R1200<R500<R900<R700.The UTS and elongation had the following order:BM(base material)<R300<R1200<R500<R900<R700.The UTS and the elongation for the WN were increased by one and three times,respectively.

Microstructure and mechanical properties of Cu/Al joints brazed using(Cu,Ni,Zr,Er)-modified Al−Si filler alloys

To design a promising Al−Si filler alloy with a relatively low melting-point,good strength and plasticity for the Cu/Al joint,the Cu,Ni,Zr and Er elements were innovatively added to modify the traditional Al−Si eutectic filler.The microstructure and mechanical properties of filler alloys and Cu/Al joints were investigated.The result indicated that the Al−Si−Ni−Cu filler alloys mainly consisted of Al(s,s),Al_(2)(Cu,Ni)and Si(s,s).The Al−10Si−2Ni−6Cu filler alloy exhibited relatively low solidus(521℃)and liquidus(577℃)temperature,good tensile strength(305.8 MPa)and fracture elongation(8.5%).The corresponding Cu/Al joint brazed using Al−10Si−2Ni−6Cu filler was mainly composed of Al_(8)(Mn,Fe)_(2)Si,Al_(2)(Cu,Ni)3,Al(Cu,Ni),Al_(2)(Cu,Ni)and Al(s,s),yielding a shear strength of(90.3±10.7)MPa.The joint strength was further improved to(94.6±2.5)MPa when the joint was brazed using the Al−10Si−2Ni−6Cu−0.2Er−0.2Zr filler alloy.Consequently,the(Cu,Ni,Zr,Er)-modified Al−Si filler alloy was suitable for obtaining high-quality Cu/Al brazed joints.

Influence of Neodymium on Amorphizability of RS Al-Fe-V-Si-Nd Alloys:An Investigation Using Time Dependent Nucleation Theory

Time dependent nucleation theory was applied to calculate the incubation time required for α Al nucleation in rapid solidified (RS) Al Fe V Si Nd alloys. The nucleation rates were calculated as a function of temperature, and the critical cooling rates required for the formation of amorphous α Al at different neodymium concentrations were calculated too. The addition of neodymium increases the amorphizablity of α Al by increasing the incubation time and decreasing the nucleation rate and the critical cooling rate. The calculations are fitted to experimental results when liquidus temperatures are estimated from an approximation, which treats Al Fe V Si Nd as quasi binary Al Fe system.

FRACTURE MECHANISM IN Ti_3Al+Si+Nb ALLOYS

Ti_3Al+Si+Nb alloys containing Ti_5Si_3 have the potential in ductility improvements. In this paper, the fracture mechanism of this alloy is under investigation. Three kinds of alloys in the as rolled condition were prepared for determination of KIC values and calculation of J-resistance curves. The results show that the morphology of Ti_5Si_3 has a great influence on the KIC. values of the alloys and crack growth resistance. The fracture mechanism is controlled by Ti_5Si_3 particles.

Influence of Si Contents on the Microstructure Evolution and Mechanical Properties of Al-Mg-Si-Cu-Zn Alloys

The influence of different Si contents on the microstructure evolution and mechanical properties of Al⁃Mg⁃Si⁃Cu⁃Zn alloys was systematically studied using tensile testing,OM,SEM,EDS,and EBSD.The results indicate that the grain size of as⁃cast alloys was gradually reduced with the increase of the Si content,which mainly resulted from the formation of many iron⁃rich phases and precipitates during the casting process.During homogenization treatment,the plate⁃likeβ⁃AlFeSi phases in the alloy with a higher Si content easily transformed to the sphericalα⁃Al(FeMn)Si phases,which is helpful for improving the formability of alloys.The microstructure evolution of the alloys was also greatly dependent on the content of Si that the number density and homogeneous distribution level of precipitates in the final cold rolled alloys both increased with the increase of the Si content,which further provided a positive effect on the formation of fine recrystallization grains during the subsequent solution treatment.As a result,the yield strength,ultimate tensile strength,and elongation of the pre⁃aged alloys in the direction of 45°with respect to the rolling direction were all increased with increasing Si content.

Microstructure and properties of rheo-HPDC Al-8Si alloy prepared by air-cooled stirring rod process

A new and effective semisolid slurry preparation process with air-cooled stirring rod(ACSR)is reported,in which the compressed air is constantly injected into the inner cavity of a stirring rod to cool the melt.The slurry of a newly developed high thermal conductivity Al?8Si alloy was prepared,and thin-wall heat dissipation shells were produced by the ACSR process combined with a HPDC machine.The effects of the air flow on the morphology ofα1-Al particles,mechanical properties and thermal conductivity of rheo-HPDC samples were studied.The results show that the excellent slurry of the alloy could be obtained with the air flow exceeding3L/s.Rheo-HPDC samples that were produced with the air flow of5L/s had the maximum UTS,YS,elongation,hardness and thermal conductivity of261MPa,124MPa,4.9%,HV99and153W/(m·K),respectively.Rheo-HPDC samples show improved properties compared to those formed by HPDC,and the increasing rates of UTS,YS,elongation,hardness and thermal conductivity were20%,15%,88%,13%and10%,respectively.

Microstructure evolution and mechanical properties of the Sip/Zn- Al composite joints by ultrasonic-assisted soldering in air

Hypereutectic Al -27Si alloys were joined without flux by ultrasonic-assisted soldering at 420 ℃ in air using Zn -5Al the filler alloys, and Si particulate-reinforced Zn - Al based composites filler joints were obtained. The ultrasonic vibration introduced into soldering could influence the migration of Si particles and the microstructure of solidified Zn - Al based alloys. Both the distribution of Si particles and microstructure of the solidified Zn - Al based alloys affected the shear strength of joints. The shear strength increased with the ultrasonic vibration time. The highest average shear strength of joints reached to -68.5 MPa. Transcrystalline rupture mode was observed on the fracture surface.

Effect of TiB2 and Al3Ti on the microstructure,mechanical properties and fracture behaviour of near eutectic Al−12.6Si alloy

A near eutectic Al−12.6Si alloy was developed with 0.0wt%,2.0wt%,4.0wt%,and 6.0wt%Al−5Ti−1B master alloy.The micro-structural morphology,hardness,tensile strength,elongation,and fracture behaviour of the alloys were studied.The unmodified Al−12.6Si al-loy has an irregular needle and plate-like eutectic silicon(ESi)and coarse polygonal primary silicon(PSi)particles in the matrix-likeα-Al phase.The P_(Si),E_(Si),andα-Al morphology and volume fraction were changed due to the addition of the Al−5Ti−1B master alloy.The hardness,UTS,and elongation improved due to the microstructural modification.Nano-sized in-situ Al3Ti particles and ex-situ TiB_(2)particles caused the mi-crostructural modification.The fracture images of the developed alloys exhibit a ductile and brittle mode of fracture at the same time.The Al−5Ti−1B modified alloys have a more ductile mode of fracture and more dimples compared to the unmodified alloy.

Thermal stability and precipitate microstructures of Al−Si−Mg−Er alloy

The effect of Er on the microhardness and precipitation behavior of the heat-treated Al−Si−Mg alloy was investigated by microhardness tester and TEM.As a comparison,the influence of natural aging was also studied.It is shown that the thermal stability of the over-aged Al−Si−Mg−Er alloy is highly related to the average size of the precipitates.The average size ofβ''precipitates in Al−Si−Mg−Er alloy is smaller than that in Al−Si−Mg alloy,and the distribution is more localized under condition of without introducing natural aging.However,when natural aging is introduced before artificial aging,the Al−Si−Mg−Er alloy has similar average size and distribution of precipitates with the Al−Si−Mg alloy,resulting in similar mechanical properties.The effect of Er on the precipitation kinetics in the alloy was also discussed in detail to explain these phenomena.

Microstructure and mechanical properties of Al−Mg−Si alloy U-shaped profile

To get a full understanding of hot extrusion,solid solution treatment and aging process on the Al−0.56Mg−0.63Si alloy,the microstructure and mechanical properties of a U-shaped profile were studied through optical microscopy,scanning electrical microscopy,transmission electrical microscopy,hardness,and tensile tests.The coarse equiaxed grains existed near the profile edge as a result of the dynamic recrystallization nucleation and exceeding growth during hot extrusion.The fibrous deformed and sub-structured grains located between the two coarse grain layers,due to the occurrence of work-hardening and dynamic recovery.Perpendicular needle β′′precipitates were distributed inside the grain,and obvious precipitates-free zone appeared after aging treatment.The tensile strength,yield strength and elongation of the aged Al−Mg−Si alloy U-shaped profile were no less than 279.4 MPa,258.6 MPa,and 21.6%,respectively.The fracture morphology showed dimple rupture characteristics.The precipitates and grain boundaries played key role in the strengthening contribution.

Microstructures and mechanical properties of in-situ TiB2/Al−xSi−0.3Mg composites

In-situ 2 vol.%TiB2 particle reinforced Al−xSi−0.3Mg(x=7,9,12,15 wt.%)composites were prepared by the salt−metal reaction,and the microstructures and mechanical properties were investigated.The results show that the TiB2 particles with a diameter of 20−80 nm and the eutectic Si with a length of 1−10μm are the main strengthening phases in the TiB2/Al−xSi−0.3Mg composites.The TiB2 particles promote grain refinement and modify the eutectic Si from needle-like to short-rod shape.However,the strengthening effect of TiB2 particles is weakened as the Si content exceeds the eutectic composition,which can be attributed to the formation of large and irregular primary Si.The axial tensile test results and fractography observations indicate that these composites show more brittle fracture characteristics than the corresponding alloy matrixes.

Refinement and thermal analysis of hypereutectic Al-25%Si alloy

Refinement and thermal analysis of hypereutectic Al 25%Si alloy were investigated with scanning electron microscope (SEM) and differential scanning calorimeter (DSC). The results show that the average size of primary silicon in Al 25%Si alloy without and with phosphorus addition are 250 μm and 30 μm, respectively. But the primary and eutectic growth temperature is raised by about 17.3 ℃ and 4?℃ respectively due to phosphorus addition. The primary nucleation temperatures are 745.0 ℃ and 762.0 ℃ for untreated and treated samples and in addition, the enthalpy changes of primary and eutectic transformation are -261.0 J/g and -397.3 J/g without phosphorus addition, -294.2 J/g and -386.1 J/g with phosphorus addition, respectively. Otherwise the mechanisms of refinement and thermal transformation of Al 25%Si alloy in solidifying process are also discussed. [

Improvement in dry sliding wear resistance of Al-17Si-5Cu alloy after an enhanced heat treatment process

To improve the wear resistance of cast Al?17Si?5Cu alloy(AR alloy),isothermal heat treatment is employed to modify the morphology of Si particles(particularly eutectic Si particles).Furthermore,wear behaviour of heat-treated alloy(HT alloy)along with AR alloy is studied using a pin-on-disc tribometer.Worn surfaces are then characterised using scanning electron microscope.The result reveals considerable microstructural modifications after the heat treatment.Accordingly,higher hardness value in HT alloy is obtained compared with AR alloy.The overall wear rate for HT alloy is found to be significantly lower compared with AR alloy at all the applied loads,indicating remarkable improvement in wear resistance.Eutectic Si particles become from acicular/rod-like to spherical/equiaxed morphology(aspect ratio close to 1)on heat treatment,resulting in good bonding with the matrix.Thus,they remain intact during wear and being harder,providing resistance to wear.Moreover,the increased hardness on heat treatment causes further resistance to wear.Therefore,the combined effect of intact harder Si particles on the wearing surface and higher hardness results in superior wear behavior in HT alloy at all loads compared with AR alloy.

Effect of pre-straining on structure and formation mechanism of precipitates in Al−Mg−Si−Cu alloy

The effect of pre-straining on the structure and formation mechanism of precipitates in an Al−Mg−Si−Cu alloy was systematically investigated by atomic resolution high-angle annular dark-field scanning transmission electron microscopy(HAADF-STEM).Elongated and string-like precipitates are formed along the dislocations in the pre-strained Al−Mg−Si−Cu alloy.The precipitates formed along the dislocations exhibit three features:non-periodic atomic arrangement within the precipitate;Cu segregation occurring at the precipitate/α(Al)interface;different orientations presented in one individual precipitate.Four different formation mechanisms of these heterogeneous precipitates were proposed as follows:elongated precipitates are formed independently in the dislocation;string-like precipitates are formed directly along the dislocations;different precipitates encounter to form string-like precipitates;precipitates are connected by other phases or solute enrichment regions.These different formation mechanisms are responsible for forming different atomic structures and morphologies of precipitates.

Relationship among solution heating rate,mechanical properties,microstructure and texture of Al−Mg−Si−Cu alloy

The relationship among heating rate, mechanical properties, microstructure and texture of Al-Mg-Si-Cu alloy during solution treatment was investigated through tensile test, scanning electron microscope, X-ray diffractometer and EBSD technology. The experimental results reveal that there is a non-monotonic relationship among solution heating rate, mechanical properties, microstructure and texture. As the solution heating rate increases, the strength variations are dependent on the tensile direction;work hardening exponent n decreases first, and then increases;plastic strain ratio r increases first, and then decreases, and finally increases. The final microstructure and texture are also affected by heating rate. As heating rate increases, the microstructure transforms from elongated grain structure to equiaxed grain structure, and the average grain size decreases first, and then increases, and decreases finally. Although the texture components including CubeND{001}<310> and P{011}<122> orientations almost have no change with the increase of heating rate, the texture intensity and volume fraction decrease first, and then increase, and finally decrease. Both microstructure and texture evolutions are weakly affected by heating rate. Improving heating rate is not always favorable for the development of fine equiaxed grain structure, weak texture and high average r value, which may be related to the recrystallization behavior.

Research on flow stress of spray formed 70Si30Al alloy under hot compression deformation

The flow stress of spray formed 70Si30Al alloy was studied by hot compression on a Gleeble- 1500 test machine. The experimental results indicated that the flow stress depends on the strain rate and the deformation temperature. The flow stress increases with an increase in strain rate at a given deformation temperature. The flow stress decreases with the deformation temperature increasing at a given strain rate. The relational expression among the flow stress, the swain rate, and the deformation temperature satisfies the Arrhenius equation. The deformation activation energy of 70Si30Al alloy during hot deformation is 866.27 kJ/mol from the Arrhenius equation.

Effect of P/M value on the preforms and microstructures of spray formed 70Si30Al alloy

A novel 70Si30Al alloy was prepared by the spray forming process for electronic packaging materials. The effect of the ratio of atomization pressure to metal melt mass flux rate （P/M） on the preforms and microstructures of the spray-deposited 70Si30Al alloy was studied. The results indicate that the PIM value has a considerable influence on the formation of the preforms and the optimal value is in the range of 0.209-0.231 MPa/（kg.min^-1）. The microstructure of the spray formed 70Si30AI alloy is fine and homogenous. The primary silicon phases distributing in the aluminum matrix evenly are fine and irregular. The aluminum matrix is divided into two groups： supersaturated α-Al phase or α-Al phase and Al-Si pseudoeutectic phase or Al-Si eutectic phase.

Effect of compression ratio on microstructure evolution of Mg−10%Al−1%Zn−1%Si alloy prepared by SIMA process

A new Mg−10%Al−1%Zn−1%Si alloy with non-dendritic microstructure was prepared by strain induced melt activation(SIMA)process.The effect of compression ratio on the evolution of semisolid microstructure of the experimental alloy was investigated.The results indicate that the average size ofα-Mg grains decreases and spheroidizing tendency becomes more obvious with the compression ratios increasing from 0 to 40%.In addition,the eutectic Mg2Si phase in the Mg−10%Al−1%Zn−1%Si alloy transforms completely from the initial fishbone shape to globular shape by SIMA process.With the increasing of compression ratio,the morphology and average size of Mg2Si phases do not change obviously.The morphology modification mechanism of Mg2Si phase in Mg−10%Al−1%Zn−1%Si alloy by SIMA process was also studied.