Micro-aluminum powder with bi-or tri-component alloy coating as a promising catalyst:Boosting pyrolysis and combustion of ammonium perchlorate

A novel design of micro-aluminum(μAl)powder coated with bi-/tri-component alloy layer,such as:Ni-P and Ni-P-Cu(namely,Al@Ni-P,Al@Ni-P-Cu,respectively),as combustion catalysts,were introduced to release its huge energy inside Al-core and promote rapid pyrolysis of ammonium perchlorate(AP)at a lower temperature in aluminized propellants.The microstructure of Al@Ni-P-Cu demonstrates that a three-layer Ni-P-Cu shell,with the thickness of~100 nm,is uniformly supported byμAl carrier(fuel unit),which has an amorphous surface with a thickness of~2.3 nm(catalytic unit).The peak temperature of AP with the addition of Al@Ni-P-Cu(3.5%)could significantly drop to 316.2℃ at high-temperature thermal decomposition,reduced by 124.3℃,in comparison to that of pure AP with 440.5℃.It illustrated that the introduction of Al@Ni-P-Cu could weaken or even eliminate the obstacle of AP pyrolysis due to its reduction of activation energy with 118.28 kJ/mol.The laser ignition results showed that the ignition delay time of Al@Ni-P-Cu/AP mixture with 78 ms in air is shorter than that of Al@Ni-P/AP(118 ms),decreased by 33.90%.Those astonishing breakthroughs were attributed to the synergistic effects of adequate active sites on amorphous surface and oxidation exothermic reactions(7597.7 J/g)of Al@Ni-P-Cu,resulting in accelerated mass and/or heat transfer rate to catalyze AP pyrolysis and combustion.Moreover,it is believed to provide an alternative Al-based combustion catalyst for propellant designer,to promote the development the propellants toward a higher energy.

Effect of Ni on microstructure and mechanical properties of Al−Mg−Si alloy for laser powder bed fusion

The microstructures and mechanical properties were systematically studied for the high-strength Al−5Mg_(2)Si−1.5Ni alloy fabricated by laser powder bed fusion(L-PBF).It is found that the introduction of Ni(1.5 wt.%)into an Al−5Mg_(2)Si alloy can significantly improve the L-PBF processibility and provide remarkable improvement in mechanical properties.The solidification range of just 85.5 K and the typical Al−Al3Ni eutectics could be obtained in the Ni-modified Al−5Mg_(2)Si samples with a high relative density of 99.8%at the volumetric energy density of 107.4 J/mm^(3).Additionally,the refined hierarchical microstructure was mainly characterized by heterogeneousα-Al matrix grains(14.6μm)that contain the interaction between dislocations and Al−Al3Ni eutectics as well as Mg_(2)Si particles.Through synergetic effects of grain refinement,dislocation strengthening and precipitation strengthening induced by Ni addition,the L-PBFed Al−5Mg_(2)Si−1.5Ni alloy achieved superior mechanical properties,which included the yield strength of(425±15)MPa,the ultimate tensile strength of(541±11)MPa and the elongation of(6.2±0.2)%.

Deformation behaviors and processing maps of CNTs/Al alloy composite fabricated by flake powder metallurgy

Deformation behaviors of CNTs/Al alloy composite fabricated by the method of flake powder metallurgy were investigated by hot compression tests, which were performed in the temperature range of 300?550 °C and strain rate range of 0.001? 10 s?1 with Gleeble?3500 thermal simulator system. Processing maps of the CNTs/Al alloy at different strains were calculated to study the optimum processing domain. Microstructures before and after hot compressions were characterized by electron backscattered diffraction (EBSD) method. Stress?strain curves indicate that the flow stress increases with the increase of strain rate and the decrease of temperature. The processing maps of the CNTs/Al alloy at different strains show that the optimum processing domain is 500?550 °C, 10 s?1 for hot working. EBSD analysis demonstrates that fully dynamic recrystallization occurs in the optimum processing domain (high strainrate 10 s?1), whereas the main soften mechanism is dynamic recovery at low strain rate (0.001 s?1).

Hot deformation and processing maps of Al_2O_3/Al composites fabricated by flake powder metallurgy

The deformation behaviors of Al2O3/Al composites were investigated by compressive tests conducted at temperature of 300-450 °C and strain rates of 0.001-1.0 s-1 with Gleeble-1500 D thermal simulator system. The results show that the flow stress increases with increasing strain rate and decreasing temperature. The hyperbolic sine constitutive equation can describe the flow stress behavior of Al2O3/Al composites, and the deformation activation energy and constitutive equations were calculated. The processing maps of Al2O3/Al-2 μm and Al2O3/Al-1 μm composites at strain of 0.6 were obtained and the optimum processing domains are in ranges of 300-330 °C, 0.007-0.03 s-1 and 335-360 °C, 0.015-0.06 s-1 for hot working, respectively. The instability zones of flow behavior can also be recognized by the maps.

Y/Al-5Ti-1B复合变质对Al-7Si合金微观组织和力学性能的影响

在传统铸造Al-Si合金中存在的粗大树枝晶α-Al相以及针状共晶Si严重割裂基体,显著降低合金的力学性能。为细化Al-Si合金的组织,提升其力学性能,本文使用扫描电镜(SEM)、电子探针(EPMA)、X射线衍射仪(XRD)以及万能材料试验机,研究了不同添加量Y/Al-5Ti-1B变质剂(Al-5Ti-1B均为2%,稀土Y分别为0.05%、0.1%、0.2%、0.3%、0.4%、0.5%,质量分数)对Al-7Si合金微观组织和力学性能的影响,并探究了其对Al-7Si合金的变质机理。实验结果表明,当Al-5Ti-1B含量为2%、稀土Y含量为0.4%时,变质效果最佳,共晶Si由粗大针状变为细小颗粒状,长和宽分别减小至2.7和0.8μm,相较于未经变质处理的Al-7Si合金,减小了90.6%和4.7%。合金抗拉强度由原来的168.1 MPa提升至209.1 MPa,增加了24.4%。同时伸长率从6.23%提升至9.62%,增长了54.4%。此外,合金的断裂方式也从脆性断裂转变为韧-脆混合断裂。

Low frequency damping behavior associated with sintering process in Al powder compact

The internal friction behavior of Al green power compact duxing the sintering process was studied as a function of temperature. The internal friction measurements were performed from room temperature to 600 °C. Two typical internal friction peaks were detected corresponding to heating and cooling processes, respectively. The heating peak corresponds to a recrystallization process of deformed Al particles, which is influenced by many extrinsic parameters, such as measuring frequency, strain amplitude, heating rate, power particle size and compacting pressure. However, the intrinsic nature of the peak is originated from the micro-sliding of the weak-bonding interfaces between Al particles and increased dislocation density induced in compressing. The cooling peak with the activation energy of (1.64±0.06) eV is associated with the grain boundary relaxation, which can be interpreted as the viscous sliding of grain boundaries. The similar phenomena are also found in the Mg green powder compact.

杂原子Ga[Al]Y分子筛吸附脱氮的模拟计算研究

利用Materials Studio软件,采用巨正则蒙特卡洛和密度泛函理论对Ga[Al]Y分子筛吸附氮化物机理进行了模拟计算研究。通过Mulliken和Hirshfeld布居分析方法,判断金属原子转移电荷数的顺序大小,得出Ga[Al]Y分子筛吸附吡啶时相对亲电性最强,吸附喹啉时的相对亲电性最弱;通过比较两种吸附构型的吸附能和吸附距离,得知Ga[Al]Y分子筛吸附脱氮主要以水平吸附构型为主,吸附能的绝对值大小顺序为:吡啶>苯胺>喹啉,分子间距离大小为:喹啉>苯胺>吡啶;由吸附等温线的模拟结果可知,Ga[Al]Y分子筛在三个温度下(288 K、293 K、298 K)对吡啶的最大吸附量均高于苯胺和喹啉。

LPSO相调控对ECAP挤压Mg-Y-Zn-Al合金组织和力学性能的影响

针对含18R-LPSO相铸态Mg-Y-Zn系合金塑韧性差、变形后力学性能提高有限的问题,研究了固溶、铸态+ECAP挤压和固溶+ECAP对Mg-3.74Y-1Zn-0.5Al(at%)合金力学性能的影响。结果表明,固溶处理诱发18R→14H-LPSO相转变、Al(Y,Zn)相化合物颗粒破碎细化,改善了合金的塑性,但强度几乎不变。铸态+ECAP挤压导致18R-LPSO和Al(Y,Zn)相破碎,并诱发大量α-Mg晶粒发生再结晶。固溶+ECAP挤压使14H-LPSO相弯曲或扭折变形、细小Al(Y,Zn)颗粒均匀分散,仅少数α-Mg晶粒发生再结晶,其强度、塑韧性远高于铸态+ECAP挤压合金的。良好强度、塑韧性匹配的14H-LPSO相的大量形成、α-Mg基体再结晶被抑制及细小Al(Y,Zn)颗粒的均匀分散是其性能提高的主要原因。

Influence of high energy ball milling on Al-30Si powder and ceramic particulate

The influence of high energy ball milling on Al 30Si powder and ceramic particulate SiC was studied by means of SEM, XRD and DSC. The results show that Al 30Si powder and their microstructure are obviously refined after high energy ball milling process. The alloy powder and SiC p stick closely to each other without interfacial reaction. DSC results detect no reaction but relaxation of the samples. So high energy ball milling can be used as an effective method for ceramic particulate pre treatment in the fabrication of MMC.

Formation regularity of phases in nanometer powders of Al-Fe alloy prepared by gas evaporation

Nanometer powders of Al Fe alloy were prepared by gas evaporation. The formation regularity of the phases in the as prepared powders and the morphology of the particles were examined. The experimental results show that chemical composition of the master alloy is the key factor which controls the chemical composition of the compound phases in nanometer powders at given evaporating temperature, the compound phases with high Fe mole fraction will form with increasing of Fe content in master alloy. Only Al 13 Fe 4, FeAl 2 and Al 2Fe compound phases form in nanometer powders in present experiment, changing of the pressure of Ar can only alter relative amounts of the compound phases in the powders. Nanometer particles with inhomogeneous tissue were obtained, which is very different from that of pure Al and Fe nanometer particles. When mole fraction of Fe in particles increases, the inhomogeneity is enhanced. [

Preparation and Mechanical Properties of-SiC Nanoparticle Reinforced Aluminum Matrix Composite by a Multi-step Powder Metallurgy Process

β-SiC nanoparticle reinforced A1 matrix （nano-SiCp/A1） composite was prepared by a multi- step powder metallurgy strategy including presureless sintering, hot compacting process and hot extrusion. The microstructures of the as-prepared composites were observed by scanning electronic microscopy （SEM）, and the mechanical properties were characterized by tensile strength measurement and Brinell hardness test. The experimental results revealed that the tensile strength of the composite with the addition of 5wt%/3-SIC nanoprtieles could be increased to 215 MPa, increasing by 110% compared with pure A1 matrix. Comparative experiments reflected that theβ-SIC nanoprticles showed significant reinforcement effect than traditional a-SiC micro-sized particles. The preparation process and sintering procedure were investigated to develop a cost effective preparation strategy to fabricate nano-SiCp/A1 composite.

Laser surface cladding of ZM5 Mg-base alloy with Al+Y powder

The surface properties of ZM5 Mg-base alloy were modified by laser cladding with Al+Y powder. Laser cladding was carried out with a 5 kW continuous wave CO2 laser by melting the preplaced powder mixture of Al and Y. Following laser cladding, the cladding zone was characterized by a detailed microstructural observation and phase analysis. Moreover, the microhardness and element distribution were evaluated in detail. The surface modified layer consists of Mg17Al12 and Al4MgY phases, while α-Mg and Mg17Al12 in the substrate. The microhardness of the cladding zone was significantly enhanced as high as HV122180 as compared to HV6080 of the substrate region. The maximal hardness about HV224 is in the interface due to the formation of intermetallic Mg17Al12 phase. The microstructure is refined and Mg diffuses into the cladding material which leads to the formation of Mg17Al12.

Assessment of the SiC＿p Distribution Uniformity in SiC＿p／Al Composites Made by Powder Metallurgy

In the manufacture of SiC_p/Al completes via powder metallurgy, the method of assessing the distri-bution uniformity of SiC particles is very important. The SiC_p distribution uniformity on each processingprocedure at the macro- and micro-mixed stages was investigated and the methods for determining mix-ture quality were put forward.

New development of powder metallurgy in automotive industry

The driving force for using powder metallurgy(PM)mostly relies on its near net-shape ability and cost-performance ratio.The automotive application is a main market of PM industry,requiring parts with competitive mechanical or functional performance in a mass production scale.As the automobile technology transforms from traditional internal combustion engine vehicles to new energy vehicles,PM technology is undergoing significant changes in manufacturing and materials development.This review outlines the challenges and opportunities generated by the changes in the automotive technology for PM.Low-cost,high-performance and light-weight are critical aspects for future PM materials development.Therefore,the studies on PM lean-alloyed steel,aluminum alloys,and titanium alloy materials were reviewed.In addition,PM soft magnetic composite applied to new energy vehicles was discussed.Then new opportunities for advanced processing,such as metal injection molding(MIM)and additive manufacturing(AM),in automotive industry were stated.In general,the change in automotive industry raises sufficient development space for PM.While,emerging technologies require more preeminent PM materials.Iron-based parts are still the main PM products due to their mechanical performance and low cost.MIM will occupy the growing market of highly flexible and complex parts.AM opens a door for fast prototyping,great flexibility and customizing at low cost,driving weight and assembling reduction.

Microstructure evolution of Al_(0.6)CoCrFeNi high entropy alloy powder prepared by high pressure gas atomization

The influence of cooling rate on the microstructure of Al0.6CoCrFeNi high entropy alloy（HEA） powders was investigated. The spherical HEA powders（D50≈78.65 μm） were prepared by high pressure gas atomization. The different cooling rates were achieved by adjusting the powder diameter. Based on the solidification model, the relationship between the cooling rate and the powder diameter was developed. The FCC phase gradually disappears as particle size decreases. Further analysis reveals that the phase structure gradually changes from FCC＋BCC dual-phase to a single BCC phase with the increase of the cooling rate. The microstructure evolves from planar crystal to equiaxed grain with the cooling rate increasing from 3.19×10^4 to 1.11×10^6 K/s.

Effect of mechanical activation on TiC synthesis reaction in Al-Ti-C powder mixture

After milling in a high energy ball miller for various times, the synthesis reaction process of the Al Ti C powder mixture were investigated by difference thermal analysis (DTA) and X ray diffractometry (XRD). According to the patterns of reaction peaks on the DTA curves, the activation energy of each reaction was calculated. The experimental results of DTA show that the synthesis reaction of Al Ti C powder mixture can be enhanced after high energy milling. The longer the milling time, the lower the reaction temperature. The synthesis reaction of TiC is transformed from Ti+C→TiC to Al 3Ti+C→TiC+3Al with long period milling. Meanwhile, the activation energy of the reaction reduces with increasing milling time. The effect of milling time on reduced activation energy for low temperature region is more significant than that for high temperature region.

Sintering study of Ti6Al4V powders with different particle sizes and their mechanical properties

Ti6Al4V powders with three different particle size distributions(0–20, 20–45, and 45–75 μm) were used to evaluate the effect of the particle size distribution on the solid-state sintering and their mechanical properties. The sintering kinetics was determined by dilatometry at temperatures from 900 to 1260°C. The mechanical properties of the sintered samples were evaluated by microhardness and compression tests. The sintering kinetics indicated that the predominant mechanism depends on the relative density irrespective of the particle size used. The mechanical properties of the sintered samples are adversely affected by increasing pore volume fraction. The elastic Young's modulus and yield stress follow a power law function of the relative density. The fracture behavior after compression is linked to the neck size developed during sintering, exhibiting two different mechanisms of failure: interparticle neck breaking and intergranular cracking in samples with relative densities below and above of 90%, respectively. The main conclusion is that relative density is responsible for the kinetics, mechanical properties, and failure behavior of Ti6 Al4 V powders.

稀土Y及Al-5Ti-B细化剂复合添加对A356铝合金组织和力学性能的影响

用Al-20Y变质剂和Al-5Ti-B细化剂处理A356铝合金熔体,研究稀土Y与Al-5Ti-B复合添加对A356铝合金组织和力学性能的影响。结果表明:稀土Y和Al-5Ti-B复合添加能提高形核率、细化α-Al晶粒尺寸和改变共晶硅形貌,共晶硅的形貌由针状和板片状变为短杆状和颗粒状,使铸造铝合金的力学性能提高。添加稀土Y和Al-5Ti-B的A356铸造铝合金的抗拉强度、屈服强度和延伸率分别为146 MPa、98 MPa和4.0%。

Characteristics of Cr and Al Powders by High Energy Ball Milling

The variation of microstucture and phase structure of metal Cr and Al powders prepared by high energy mechanical milling was analyzed and investigated.The results show that with the continuous balling the average grain sizes of the brittle Cr powders are gradually decreased,and the diffraction peaks are widened and the peak values lower owing to the interrelation caused by both cold welding and breaking;the tough Al powders exhibit intense cold welding,and most of powders lead to adhesion to ball surface and pot wall,meanwhile,the Al powders subjected to intense deformation have led to many dislocation rings with non dislocation wind up found in the microstructure.

Fabrication of Ni_3Al by hot pressing from element powders

Ni3Al intermetaUic was synthesized by hot pressing from element powders of nickel, aluminum, and boron. The influences of parameters on the properties of Ni3Al were investigated. The parameters include the particle size of nickel powder, adding or without boron powder, hot pressing temperature, etc. The properties include the density of hot-pressed samples, resultant redo of Ni3A1 phase, and bending strength. The microstructures of hot-pressed samples were investigated by X-ray diffraction and scan electronic microscopy, and the properties, such as density and bending strength, were also measured. The results show that a higher bending strength was obtained under the same hot pressing conditions by the fine nickel powder than the coarse one, and there is little difference about density. Boron powder added in this process accelerates the formation of Ni3Al and markedly increases the hot pressed density. In the temperature range of this study, the density increases along with the hot pressing temperature. Full dense Ni3Al samples were obtained under the condition of 860℃, 10 min, 45 MPa from Ni-22.89A1-0.5B powder.