Zn-Al coatings can provide protection to exposed steel parts in most environments. For this reason, the investigation of Zn-Al coatings become very popular in recent years. In order to study the microstructures and pr...Zn-Al coatings can provide protection to exposed steel parts in most environments. For this reason, the investigation of Zn-Al coatings become very popular in recent years. In order to study the microstructures and properties of mechanically deposited Zn-Al coating, zinc powders and aluminum powders were used to deposit Zn-AI coating by mechanical plating. The microstruetures, phase constitutes and compositions of the coating were observed and analyzed with optical microscopy （OM）, scanning electron microscopy（SEM）, X-ray diffraction（XRD） and X-ray energy-dispersive spectroscopy（EDS）. The results of observation show that the coating consists of almost spherically shaped zinc particles point contacting with each other; the coatings are composed of zinc particles, aluminum particles, interstice, and tin; extra fine zinc powders and some smaller interspersed inclusions are positioned in the interstices. Porosity and thickness of the coating were tested by ferroxyl test and magnetic method. The corrosion resistance of coatings was studied by neutral salt spraying test（NSS）, immersion test and electrochemical polarization. It is found that the thickness of the coating dose lacks uniformity, with an uneven thickness distribution and an average variation of approximately 2-5gm; the coating can afford cathodic protection to the steel substrate; the corrosion resistance of Zn-Al coatings is better than that of the mechanically plated zinc coatings with same thickness. These conclusions can be applied to improve anti-corrosion performance by mechanically deposit Zn-Al coatings.展开更多
Thermal sprayed Ni-20wt. % Al coating is fabricated on 6061-T6 aluminum alloy substrates by twin-wire arc spraying （TWAS）. Experimental results present that the average bonding strength is around 53 MPa and the aver...Thermal sprayed Ni-20wt. % Al coating is fabricated on 6061-T6 aluminum alloy substrates by twin-wire arc spraying （TWAS）. Experimental results present that the average bonding strength is around 53 MPa and the average hardness reaches 325 HV. The Vickers microhardness of NiAl and Ni3Al intermetaUic compounds is larger than that of the substrate, which is beneficial for improving the wear property. Wear mechanism exhibits features of adhesive wear. Friction and wear test results indicate that the wet friction coefficient is higher than the coefficient of dry friction after 200 cycles, and variations of the wet friction coefficient are relatively smaller.展开更多
Al coated steel sheets with excellent heat resistance,thermal reflection,and corrosion resistance are widely used in various applications.The laser weldability of the Al coated steel sheet for full penetration welding...Al coated steel sheets with excellent heat resistance,thermal reflection,and corrosion resistance are widely used in various applications.The laser weldability of the Al coated steel sheet for full penetration welding was reported.The phenomenon caused by intermixed aluminum and behavior of aluminum in the weld were investigated.Al coated steel sheets that have various thickness and coating mass were prepared for laser welding.The effects of parameters such as welding conditions and Al coating conditions were investigated.Al content mixed in the weld after laser welding was evaluated,and then a correlation between the mixed Al and mechanical properties was investigated.The results show that the Al-rich zones which have Fe-Al intermetallic compounds are found in the weld.The intermetallic compounds cause the decreased strength of the weld.展开更多
The friction and wear behavior of Fe Al intermetallics based coating produced by high velocity arc spraying technique under dry sliding at room temperature were investigated using a ball on disc tribotester. The ef...The friction and wear behavior of Fe Al intermetallics based coating produced by high velocity arc spraying technique under dry sliding at room temperature were investigated using a ball on disc tribotester. The effect of sliding speed on friction coefficient and wear of the coating was studied. The worn surface of the coating was analyzed by scanning electron microscope (SEM) to explore sliding friction and wear mechanism. The results show that the variations of friction coefficient can be divided into three distinct steps during the trail. Both the friction coefficient and the wear of the coating increase with increased sliding speed due to accelerated crack propagation rate and lamellar structure with poor ductility of the coating. The coating surface is subjected to alternately tensile stress and compression stress during sliding wear process, and the predominant wear mechanism of the coatings appears to be brittle fracture and delamination.展开更多
The halide-activated pack cementation method is utilized to codeposit aluminum and silicon on Mo substrate. Emphasis is placed on the microstructure and elevated-temperature oxidation resistance of coatings. The resul...The halide-activated pack cementation method is utilized to codeposit aluminum and silicon on Mo substrate. Emphasis is placed on the microstructure and elevated-temperature oxidation resistance of coatings. The results show that hexagonal Mo(Si, Al)2 as a main phase and a little amount of the lower disilicide Mo5Si3 was formed on Mo substrate through the halide-activated pack cementation method. The resultant Si-Al coating on Mo substrate exhibits excellent cyclic oxidation resistance. The excellent cyclic oxidation resistance of the coatings is attributed to the formation of alumina on the coatings during the oxidation.展开更多
The outermost coating with single phase Ni2Al3 was obtained on copper surface by electrodepositing nickel followed by slurry pack aluminizing at 800 °C for 12 h. The oxidation resistance and microstructure of the...The outermost coating with single phase Ni2Al3 was obtained on copper surface by electrodepositing nickel followed by slurry pack aluminizing at 800 °C for 12 h. The oxidation resistance and microstructure of the coating oxidized in ambient air at 1000 °C for 25-250 h were investigated using SEM, X-ray diffraction and optical microscope methods. The results show that the copper with single phase Ni2Al3 coating possesses the best high temperature oxidation resistance, and the mass gain of the coating is 1/15 that of pure copper and 1/2 that of nickel coating, respectively. The specimen surface after being oxidized for 25 h still comprises Ni2Al3 phase. However, when the time of oxidizing treatment increases to 50 h, the Ni Al phase is formed. It is also found that the Ni2Al3 phase completely turns into Ni Al phase after oxidizing treatment for 100 h and above. The Ni Al coating shows excellent high temperature oxidation resistance when oxidation time is 250 h.展开更多
Al coated NdFeB magnets were prepared by plasma-assisted-physical-vapor-deposition(PA-PVD)method fo r enhancing the corro sion resistance.Mo rphologies and structures were characterized by an Xray diffractometer and a...Al coated NdFeB magnets were prepared by plasma-assisted-physical-vapor-deposition(PA-PVD)method fo r enhancing the corro sion resistance.Mo rphologies and structures were characterized by an Xray diffractometer and a scanning electron microscope.Corrosion behaviors of the samples with different bias voltages were studied by electrochemical methods and neutral salt spray test,respectively.The bias voltage during the deposition process was optimized according to the coating structures and corrosion resistances.The density and flatness of Al coating increase with increasing the bias voltage,and at the same time the thickness decreases.The coating density and thickness turn to be stable when bias voltage is 1800 V.Also,the corrosion behaviors of PA-PVD Al coatings in different media,such as NaOH,HNO_(3) and NaCl solutions,were studied.The self-corrosion potentials(E_(corr)) of PA-PVD Al coatings almost keep constant in NaOH and HNO_(3) solutions with diffe rent concentrations.However,the self-corrosion current densities(J_(corr)) decrease with the increasing concentrations.E_(corr) shifts to negative potential and J_(corr)decreases gradually when increasing the concentration of NaCl solution.The corrosion mechanisms of Al coatings are discussed based on the corrosion behaviors in different media.展开更多
(Ni,Pd)AI coating, prepared by low pressure pack cementation on the Ni-base superalloy M38 where Pd-20 wt pct Ni alloy was predeposited, consists of a single β-(Ni,Pd)AI phase. The initial isothermal oxidation behavi...(Ni,Pd)AI coating, prepared by low pressure pack cementation on the Ni-base superalloy M38 where Pd-20 wt pct Ni alloy was predeposited, consists of a single β-(Ni,Pd)AI phase. The initial isothermal oxidation behavior of (Ni,Pd)AI coating was investigated by TGA, XRD, SEM/EDS at 800-1100℃. Results show that oxidation kinetics accord preferably with parabolic law at 800, 900 and 1100℃, but not at 1000℃. θ-AI203 was observed at 800-1100℃. It is found that Pd plays an important role in accelerating the diffusion of Ti from the substrate to the coating surface in the aluminide coating.展开更多
Effects of NaI as an additive on electrodeposition of Al coatings in AlCl_(3)-NaCl-KCl(80-10-10 wt-%)molten salts electrolyte at 150°C were investigated by means of cyclic voltammetry,chronopotentiometry,scanning...Effects of NaI as an additive on electrodeposition of Al coatings in AlCl_(3)-NaCl-KCl(80-10-10 wt-%)molten salts electrolyte at 150°C were investigated by means of cyclic voltammetry,chronopotentiometry,scanning electron microscopy and X-ray diffraction(XRD).Results reveal that addition of NaI in the electrolyte intensifies cathodic polarization,inhibits growth of Al deposits and increases number density of charged particles.The electrodeposition of Al coatings in the AlCl_(3)-NaCl-KCl molten salts electrolyte proceeds via three-dimensional instantaneous nucleation which however exhibits irrelevance with NaI.Galvanostatic deposition results indicate that NaI could facilitate the formation of uniform Al deposits.A compact coating consisting of Al deposits with an average particle size of 3μm was obtained at a current density of 50 mA∙cm^(−2) in AlCl_(3)-NaCl-KCl molten salts electrolyte with 10 wt-%NaI.XRD analysis confirmed that NaI could contribute to the formation of Al coating with a preferred crystallographic orientation along(220)plane.展开更多
High-temperature titanium alloy for aeroengine compressor applications suffers from high-temperature oxidation and environmental corrosion, which prohibits long-term service of this kind alloy at temperatures above 60...High-temperature titanium alloy for aeroengine compressor applications suffers from high-temperature oxidation and environmental corrosion, which prohibits long-term service of this kind alloy at temperatures above 600℃. In an attempt to tackle this problem, Ti-48Al （at. pct） and Ti-48Al-12Cr （at. pct） protective coatings were plated on the substrate of alloy Ti-60 by arc ion plating （ALP） method. Isothermal and cyclic oxidation tests were performed in static air at elevated temperatures. Phase composition, morphology of the coatings and distribution of elements were investigated by X-ray diffraction （XRD）, scanning electron microscopy （SEM） and energy dispersive X-ray analysis （EDX）. The results showed that the Ti-48Al coating exhibited good isothermal oxidation resistance during exposure at 800℃, but poorer resistance against oxidation at 900℃. By contrast Ti-48Al-12Cr coating demonstrated excellent isothermal oxidation resistance at both temperatures. Cyclic oxidation tests performed at 800℃ indicated that resistance and no spallation of coatings was observed. But both coatings demonstrated good cyclic oxidation at 900℃ only Ti-48Al-12Cr coating demonstrated excellent cyclic oxidation resistance.展开更多
A Ti(Al,Si)3 diffusion coating was prepared on γ-TiAl alloy by cold sprayed Al?20Si alloy coating, followed by a heat-treatment. The isothermal and cyclic oxidation tests were conducted at 900 °C for 1000 h and ...A Ti(Al,Si)3 diffusion coating was prepared on γ-TiAl alloy by cold sprayed Al?20Si alloy coating, followed by a heat-treatment. The isothermal and cyclic oxidation tests were conducted at 900 °C for 1000 h and 120 cycles to check the oxidation resistance of the coating. The microstructure and phase transformation of the coating before and after the oxidation were studied by SEM, XRD and EPMA. The results indicate that the diffusion coating shows good oxidation resistance. The mass gain of the diffusion coating is only a quarter of that of bare alloy. After oxidation, the diffusion coating is degraded into three layers: an inner TiAl2 layer, a two-phase intermediate layer composed of a Ti(Al,Si)3 matrix and Si-rich precipitates, and a porous layer because of the inter-diffusion between the coating and substrate.展开更多
Al2O3/Au nano-laminated composite coatings were prepared by means of magnetron sputtering. The coating was compact and comprised of nano-laminated Al2O3 and Au layers. High temperature cyclic oxidation test was employ...Al2O3/Au nano-laminated composite coatings were prepared by means of magnetron sputtering. The coating was compact and comprised of nano-laminated Al2O3 and Au layers. High temperature cyclic oxidation test was employed to investigate the oxidation resistance of the composite coatings. The results revealed that the applied Al2O3/Au nano-laminated composite coatings improved the oxidation and spallation resistance of the stainless steel substrate significantly. The mechanism accounting for oxidation resistance was related with the suppression of inward oxygen diffusion and selective oxidation of Cr in the substrate. The mechanism accounting for spallation resistance was attributed to the relaxation of thermal stress by the nano-laminated structure.展开更多
1. Introduction High temperature oxidation resistanceof alloys depends on the formation of adense oxide scale with slow growing rateon its top surface. The α-Al;O;films appearto be the oxide with the lowest growingra...1. Introduction High temperature oxidation resistanceof alloys depends on the formation of adense oxide scale with slow growing rateon its top surface. The α-Al;O;films appearto be the oxide with the lowest growingrate. In the CoCrAl systems, the continuousα-Al;O;can not be formed if the contentof aluminium in the alloy is less than severalhundredths. For the improvement ofoxidation resistance of MCrAl （M=Co,Ni and Fe）, many studies have been conducted展开更多
Al2O3p/Al composite coatings were prepared on the surface of AZ31 magnesium alloy by plasma spraying technology with mixed powders of Al and Al2O3. An orthogonal test containing six factors and five levels was carried...Al2O3p/Al composite coatings were prepared on the surface of AZ31 magnesium alloy by plasma spraying technology with mixed powders of Al and Al2O3. An orthogonal test containing six factors and five levels was carried out to acquire the optimum technical parameters. Mierostruetures and properties of the composite coatings were studied. The results show that the coatings consist of Al2O3 particulates distributed uniformly and Al matrix, and the interface between the particulate and matrix is continuous, compact and clean. With increasing the mass fraction of Al2O3 in the mixed powders, the volume fraction of Al2O3 in the coatings iacreases. The Al2O3p/Al composite coating with 14% Al2O3 volume fraction has more compact microstrueture and more satisfactory properties.展开更多
The microstructure of a composite coating system, which was composed of an inner layer of Fe-Cr-Al and an outer layer of aluminum, was studied after it was respectively oxidized and sulfurdized at elevated temperature...The microstructure of a composite coating system, which was composed of an inner layer of Fe-Cr-Al and an outer layer of aluminum, was studied after it was respectively oxidized and sulfurdized at elevated temperatures. Apart from the Al2O3 scale formed on the surface, the microstructure of the composite coatings exposed at 900℃ in air for 4h was a three-layer structure. The first layer consisted of a solid solution of Cr and Fe in α aluminum and an intermetallic compound FeAl3 while the second layer was a single phase of the aluminide and the third layer still remained the same appearance as the original Fe-Cr-Al coating. The microstructural observation of the specimen tested at 850-900℃ at low oxygen pressure and high sulfur pressure for 576h revealed that the surface coatings of the specimen had transformed into a duplex structure containing an outer layer and a thicker aluminide layer beneath. X-ray diffraction results showed that the out layer was composed of Al2S3 and Al2O3 and that AlCrFee was the main phase composition of the aluminide layer, with a few of Al2S3 and Al2O3 accompanied.展开更多
基金supported by National Natural Science Foundation of China (Grant No. 50561003)Foundation of Yunnan Provincial Education Department of China (Grant No.07Y41414)
文摘Zn-Al coatings can provide protection to exposed steel parts in most environments. For this reason, the investigation of Zn-Al coatings become very popular in recent years. In order to study the microstructures and properties of mechanically deposited Zn-Al coating, zinc powders and aluminum powders were used to deposit Zn-AI coating by mechanical plating. The microstruetures, phase constitutes and compositions of the coating were observed and analyzed with optical microscopy （OM）, scanning electron microscopy（SEM）, X-ray diffraction（XRD） and X-ray energy-dispersive spectroscopy（EDS）. The results of observation show that the coating consists of almost spherically shaped zinc particles point contacting with each other; the coatings are composed of zinc particles, aluminum particles, interstice, and tin; extra fine zinc powders and some smaller interspersed inclusions are positioned in the interstices. Porosity and thickness of the coating were tested by ferroxyl test and magnetic method. The corrosion resistance of coatings was studied by neutral salt spraying test（NSS）, immersion test and electrochemical polarization. It is found that the thickness of the coating dose lacks uniformity, with an uneven thickness distribution and an average variation of approximately 2-5gm; the coating can afford cathodic protection to the steel substrate; the corrosion resistance of Zn-Al coatings is better than that of the mechanically plated zinc coatings with same thickness. These conclusions can be applied to improve anti-corrosion performance by mechanically deposit Zn-Al coatings.
文摘Thermal sprayed Ni-20wt. % Al coating is fabricated on 6061-T6 aluminum alloy substrates by twin-wire arc spraying （TWAS）. Experimental results present that the average bonding strength is around 53 MPa and the average hardness reaches 325 HV. The Vickers microhardness of NiAl and Ni3Al intermetaUic compounds is larger than that of the substrate, which is beneficial for improving the wear property. Wear mechanism exhibits features of adhesive wear. Friction and wear test results indicate that the wet friction coefficient is higher than the coefficient of dry friction after 200 cycles, and variations of the wet friction coefficient are relatively smaller.
文摘Al coated steel sheets with excellent heat resistance,thermal reflection,and corrosion resistance are widely used in various applications.The laser weldability of the Al coated steel sheet for full penetration welding was reported.The phenomenon caused by intermixed aluminum and behavior of aluminum in the weld were investigated.Al coated steel sheets that have various thickness and coating mass were prepared for laser welding.The effects of parameters such as welding conditions and Al coating conditions were investigated.Al content mixed in the weld after laser welding was evaluated,and then a correlation between the mixed Al and mechanical properties was investigated.The results show that the Al-rich zones which have Fe-Al intermetallic compounds are found in the weld.The intermetallic compounds cause the decreased strength of the weld.
基金NationalNatureScienceFoundationofChina (No .5 0 0 0 5 0 2 4)
文摘The friction and wear behavior of Fe Al intermetallics based coating produced by high velocity arc spraying technique under dry sliding at room temperature were investigated using a ball on disc tribotester. The effect of sliding speed on friction coefficient and wear of the coating was studied. The worn surface of the coating was analyzed by scanning electron microscope (SEM) to explore sliding friction and wear mechanism. The results show that the variations of friction coefficient can be divided into three distinct steps during the trail. Both the friction coefficient and the wear of the coating increase with increased sliding speed due to accelerated crack propagation rate and lamellar structure with poor ductility of the coating. The coating surface is subjected to alternately tensile stress and compression stress during sliding wear process, and the predominant wear mechanism of the coatings appears to be brittle fracture and delamination.
文摘The halide-activated pack cementation method is utilized to codeposit aluminum and silicon on Mo substrate. Emphasis is placed on the microstructure and elevated-temperature oxidation resistance of coatings. The results show that hexagonal Mo(Si, Al)2 as a main phase and a little amount of the lower disilicide Mo5Si3 was formed on Mo substrate through the halide-activated pack cementation method. The resultant Si-Al coating on Mo substrate exhibits excellent cyclic oxidation resistance. The excellent cyclic oxidation resistance of the coatings is attributed to the formation of alumina on the coatings during the oxidation.
基金Projects(CKJB201205,QKJB201202,YJK201307)supported by the Nanjing Institute of Technology,China
文摘The outermost coating with single phase Ni2Al3 was obtained on copper surface by electrodepositing nickel followed by slurry pack aluminizing at 800 °C for 12 h. The oxidation resistance and microstructure of the coating oxidized in ambient air at 1000 °C for 25-250 h were investigated using SEM, X-ray diffraction and optical microscope methods. The results show that the copper with single phase Ni2Al3 coating possesses the best high temperature oxidation resistance, and the mass gain of the coating is 1/15 that of pure copper and 1/2 that of nickel coating, respectively. The specimen surface after being oxidized for 25 h still comprises Ni2Al3 phase. However, when the time of oxidizing treatment increases to 50 h, the Ni Al phase is formed. It is also found that the Ni2Al3 phase completely turns into Ni Al phase after oxidizing treatment for 100 h and above. The Ni Al coating shows excellent high temperature oxidation resistance when oxidation time is 250 h.
基金Project supported by Fundamental Research Funds for the Central Universities(JZ2019YYPY0291)。
文摘Al coated NdFeB magnets were prepared by plasma-assisted-physical-vapor-deposition(PA-PVD)method fo r enhancing the corro sion resistance.Mo rphologies and structures were characterized by an Xray diffractometer and a scanning electron microscope.Corrosion behaviors of the samples with different bias voltages were studied by electrochemical methods and neutral salt spray test,respectively.The bias voltage during the deposition process was optimized according to the coating structures and corrosion resistances.The density and flatness of Al coating increase with increasing the bias voltage,and at the same time the thickness decreases.The coating density and thickness turn to be stable when bias voltage is 1800 V.Also,the corrosion behaviors of PA-PVD Al coatings in different media,such as NaOH,HNO_(3) and NaCl solutions,were studied.The self-corrosion potentials(E_(corr)) of PA-PVD Al coatings almost keep constant in NaOH and HNO_(3) solutions with diffe rent concentrations.However,the self-corrosion current densities(J_(corr)) decrease with the increasing concentrations.E_(corr) shifts to negative potential and J_(corr)decreases gradually when increasing the concentration of NaCl solution.The corrosion mechanisms of Al coatings are discussed based on the corrosion behaviors in different media.
文摘(Ni,Pd)AI coating, prepared by low pressure pack cementation on the Ni-base superalloy M38 where Pd-20 wt pct Ni alloy was predeposited, consists of a single β-(Ni,Pd)AI phase. The initial isothermal oxidation behavior of (Ni,Pd)AI coating was investigated by TGA, XRD, SEM/EDS at 800-1100℃. Results show that oxidation kinetics accord preferably with parabolic law at 800, 900 and 1100℃, but not at 1000℃. θ-AI203 was observed at 800-1100℃. It is found that Pd plays an important role in accelerating the diffusion of Ti from the substrate to the coating surface in the aluminide coating.
基金The authors would gratefully acknowledge the financial support from the National Natural Science Foundation of China(Grant No.51301110)China Postdoctoral Science Foundation(No.2016M600311)Science and Technology Innovation Action Plan—International Enterprises Science and Technology Cooperation Program of Shanghai(No.17230732700).
文摘Effects of NaI as an additive on electrodeposition of Al coatings in AlCl_(3)-NaCl-KCl(80-10-10 wt-%)molten salts electrolyte at 150°C were investigated by means of cyclic voltammetry,chronopotentiometry,scanning electron microscopy and X-ray diffraction(XRD).Results reveal that addition of NaI in the electrolyte intensifies cathodic polarization,inhibits growth of Al deposits and increases number density of charged particles.The electrodeposition of Al coatings in the AlCl_(3)-NaCl-KCl molten salts electrolyte proceeds via three-dimensional instantaneous nucleation which however exhibits irrelevance with NaI.Galvanostatic deposition results indicate that NaI could facilitate the formation of uniform Al deposits.A compact coating consisting of Al deposits with an average particle size of 3μm was obtained at a current density of 50 mA∙cm^(−2) in AlCl_(3)-NaCl-KCl molten salts electrolyte with 10 wt-%NaI.XRD analysis confirmed that NaI could contribute to the formation of Al coating with a preferred crystallographic orientation along(220)plane.
文摘High-temperature titanium alloy for aeroengine compressor applications suffers from high-temperature oxidation and environmental corrosion, which prohibits long-term service of this kind alloy at temperatures above 600℃. In an attempt to tackle this problem, Ti-48Al （at. pct） and Ti-48Al-12Cr （at. pct） protective coatings were plated on the substrate of alloy Ti-60 by arc ion plating （ALP） method. Isothermal and cyclic oxidation tests were performed in static air at elevated temperatures. Phase composition, morphology of the coatings and distribution of elements were investigated by X-ray diffraction （XRD）, scanning electron microscopy （SEM） and energy dispersive X-ray analysis （EDX）. The results showed that the Ti-48Al coating exhibited good isothermal oxidation resistance during exposure at 800℃, but poorer resistance against oxidation at 900℃. By contrast Ti-48Al-12Cr coating demonstrated excellent isothermal oxidation resistance at both temperatures. Cyclic oxidation tests performed at 800℃ indicated that resistance and no spallation of coatings was observed. But both coatings demonstrated good cyclic oxidation at 900℃ only Ti-48Al-12Cr coating demonstrated excellent cyclic oxidation resistance.
基金Project(50971127)supported by the National Natural Science Foundation of China
文摘A Ti(Al,Si)3 diffusion coating was prepared on γ-TiAl alloy by cold sprayed Al?20Si alloy coating, followed by a heat-treatment. The isothermal and cyclic oxidation tests were conducted at 900 °C for 1000 h and 120 cycles to check the oxidation resistance of the coating. The microstructure and phase transformation of the coating before and after the oxidation were studied by SEM, XRD and EPMA. The results indicate that the diffusion coating shows good oxidation resistance. The mass gain of the diffusion coating is only a quarter of that of bare alloy. After oxidation, the diffusion coating is degraded into three layers: an inner TiAl2 layer, a two-phase intermediate layer composed of a Ti(Al,Si)3 matrix and Si-rich precipitates, and a porous layer because of the inter-diffusion between the coating and substrate.
基金Project (50771021) supported by the National Natural Science Foundation of China
文摘Al2O3/Au nano-laminated composite coatings were prepared by means of magnetron sputtering. The coating was compact and comprised of nano-laminated Al2O3 and Au layers. High temperature cyclic oxidation test was employed to investigate the oxidation resistance of the composite coatings. The results revealed that the applied Al2O3/Au nano-laminated composite coatings improved the oxidation and spallation resistance of the stainless steel substrate significantly. The mechanism accounting for oxidation resistance was related with the suppression of inward oxygen diffusion and selective oxidation of Cr in the substrate. The mechanism accounting for spallation resistance was attributed to the relaxation of thermal stress by the nano-laminated structure.
文摘1. Introduction High temperature oxidation resistanceof alloys depends on the formation of adense oxide scale with slow growing rateon its top surface. The α-Al;O;films appearto be the oxide with the lowest growingrate. In the CoCrAl systems, the continuousα-Al;O;can not be formed if the contentof aluminium in the alloy is less than severalhundredths. For the improvement ofoxidation resistance of MCrAl （M=Co,Ni and Fe）, many studies have been conducted
基金the financial support from the National Natural Science Foundation of China(No.52222510)Key Research and Development Program of Shandong Province,China(No.2021ZLGX01)。
基金This research was supported by Jilin Province Science Foundation （No. 20090552）.
文摘Al2O3p/Al composite coatings were prepared on the surface of AZ31 magnesium alloy by plasma spraying technology with mixed powders of Al and Al2O3. An orthogonal test containing six factors and five levels was carried out to acquire the optimum technical parameters. Mierostruetures and properties of the composite coatings were studied. The results show that the coatings consist of Al2O3 particulates distributed uniformly and Al matrix, and the interface between the particulate and matrix is continuous, compact and clean. With increasing the mass fraction of Al2O3 in the mixed powders, the volume fraction of Al2O3 in the coatings iacreases. The Al2O3p/Al composite coating with 14% Al2O3 volume fraction has more compact microstrueture and more satisfactory properties.
文摘The microstructure of a composite coating system, which was composed of an inner layer of Fe-Cr-Al and an outer layer of aluminum, was studied after it was respectively oxidized and sulfurdized at elevated temperatures. Apart from the Al2O3 scale formed on the surface, the microstructure of the composite coatings exposed at 900℃ in air for 4h was a three-layer structure. The first layer consisted of a solid solution of Cr and Fe in α aluminum and an intermetallic compound FeAl3 while the second layer was a single phase of the aluminide and the third layer still remained the same appearance as the original Fe-Cr-Al coating. The microstructural observation of the specimen tested at 850-900℃ at low oxygen pressure and high sulfur pressure for 576h revealed that the surface coatings of the specimen had transformed into a duplex structure containing an outer layer and a thicker aluminide layer beneath. X-ray diffraction results showed that the out layer was composed of Al2S3 and Al2O3 and that AlCrFee was the main phase composition of the aluminide layer, with a few of Al2S3 and Al2O3 accompanied.
