期刊文献+
共找到3,208篇文章
< 1 2 161 >
每页显示 20 50 100
Efficient removal of Al(Ⅲ)and P507 from high concentration MgCl_(2)solution based on in-situ reaction strategy
1
作者 Qiang WANG Meng WANG +3 位作者 Zong-yu FENG Yong-qi ZHANG Xiao-wei HUANG Xiang-xin XUE 《Transactions of Nonferrous Metals Society of China》 SCIE EI CAS CSCD 2024年第9期3042-3053,共12页
For a highly efficient recycling of a wastewater containing a high concentration of MgCl_(2),Al(Ⅲ)and P507 were scheduled to be removed in advance.In this study,the in-situ removal of Al(Ⅲ)and P507 from a high conce... For a highly efficient recycling of a wastewater containing a high concentration of MgCl_(2),Al(Ⅲ)and P507 were scheduled to be removed in advance.In this study,the in-situ removal of Al(Ⅲ)and P507 from a high concentration MgCl_(2)solution at different pH values and Al/P molar ratios was investigated.The results showed that P507 formed organic complexes of Al_(x)(OH)_y^(Z+)-P507 at pH of 2.0-4.0.At pH of 4.0-5.0,Al(Ⅲ)precipitated and transferred into Al(OH)_(3)with a flocculent amorphous morphology.Active sites on the Al(OH)_(3)surface enhanced the removal efficiency of P507.At pH of 6.0-6.5,Al(Ⅲ)and Mg(Ⅱ)formed layered crystalline Al(OH)_(3)and MgAl_(2)(OH)_(8with)small pore channels and fewer active sites,resulting in a reduced removal efficiency of P507.When the Al/P molar ratio exceeded 13 and the pH was between 4.0 and 5.0,the removal rates of both Al(Ⅲ)and P507 were higher than98%,while the concentration loss of Mg(Ⅱ)was only 0.2%-0.9%. 展开更多
关键词 in-situ removal al(III) P507 MgCl_(2)solution pH al/P molar ratio
下载PDF
锌镁比对Al-Zn-Mg-Cu-Er-Sc-Zr合金显微组织与耐腐蚀性能影响的研究 被引量:1
2
作者 王少华 武晓辉 +3 位作者 梁爽 邢清源 孟令刚 张兴国 《热加工工艺》 北大核心 2024年第6期112-116,121,共6页
通过调整Al-Zn-Mg-Cu-Er-Sc-Zr合金中的Mg元素含量,研究了Zn/Mg比的变化对合金相演变以及腐蚀性能的影响规律。结果表明:Al_(8)Cu_(4)Er相、Al_(3)(Er,Sc)相与含Fe相存在明显的伴生关系,二者依附于含Fe相生长。Zn/Mg比的变化可显著改变... 通过调整Al-Zn-Mg-Cu-Er-Sc-Zr合金中的Mg元素含量,研究了Zn/Mg比的变化对合金相演变以及腐蚀性能的影响规律。结果表明:Al_(8)Cu_(4)Er相、Al_(3)(Er,Sc)相与含Fe相存在明显的伴生关系,二者依附于含Fe相生长。Zn/Mg比的变化可显著改变三者间的交互形式,高的Zn/Mg比例有利于稀土相独立生长,且在比值为4.18的条件下,Al_(8)Cu_(4)Er相与含Fe相均得到了显著细化。细化的晶界第二相使腐蚀坑深度仅为82μm,而连续的伴生混合相、粗大稀土相等均会不同程度降低合金的耐蚀性能。 展开更多
关键词 al-Zn-Mg-Cu-Er-Sc-Zr铝合金 Zn/Mg比 稀土相 晶间腐蚀
下载PDF
Cross section determination of^(27)Al(n,2n)^(26)Al reaction induced by 14-MeV neutrons uniting with D-T neutron activation and AMS techniques 被引量:1
3
作者 Xian-Lin Yang Chang-Lin Lan +6 位作者 Yu-Ting Wei Yi Zhang Gong Jiang Bo Xie Yu Liu Hong-Tao Shen Xiao-Jun Sun 《Nuclear Science and Techniques》 SCIE EI CAS CSCD 2024年第6期78-89,共12页
Aluminum is the primary structural material in nuclear engineering,and its cross section induced by 14-MeV neutrons is of great significance.To address the issue of insufficient accuracy for the^(27)Al(n,2n)^(26)Al re... Aluminum is the primary structural material in nuclear engineering,and its cross section induced by 14-MeV neutrons is of great significance.To address the issue of insufficient accuracy for the^(27)Al(n,2n)^(26)Al reaction cross section,the activation method and accelerator mass spectrometry(AMS)technique were used to determine the^(27)Al(n,2n)^(26)Al cross section,which could be used as a D-T plasma ion temperature monitor in fusion reactors.At the China Academy of Engineering Physics,neutron activation was performed using a K-400 neutron generator produced by the T(d,n)4He reaction.The^(26)Al∕^(27)Al isotope ratios were measured using the newly installed GYIG 1 MV AMS at the Institute of Geochemistry,Chinese Academy of Sciences.The neutron flux was monitored by measuring the activity of 92mNb produced by the 93Nb(n,2n)92mNb reaction.The measured results were compared with available data in the experimental nuclear reaction database,and the measured values showed a reasonable degree of consistency with partially available literature data.The newly acquired cross-sectional data at 12 neutron energy points through systematic measurements clarified the divergence,which has two different growth trends from the existing experimental values.The obtained results are also compared with the corresponding evaluated database,and the newly calculated excitation functions with TALYS−1.95 and EMPIRE−3.2 codes,the agreement with CENDL−3.2,TENDL-2021 and EMPIRE−3.2 results are generally acceptable.A substantial improvement in the knowledge of the^(27)Al(n,2n)^(26)Al reaction excitation function was obtained in the present work,which will lay the foundation for the diagnosis of the fusion ion temperature,testing of the nuclear physics model,evaluation of nuclear data,etc. 展开更多
关键词 14-MeV neutron ^(27)al(n 2n)^(26)al Cross section AMS
下载PDF
Pickering乳液自组装CL-20/n-Al/F2605复合空心微球的制备与性能
4
作者 孙鹏瞻 杨敏 +4 位作者 尢淇 高登钊 李聪颖 张行泉 郭长平 《爆破器材》 CAS CSCD 北大核心 2024年第4期9-16,共8页
高能量、高爆热的六硝基六氮杂异伍兹烷(CL-20)/Al复合物由于自身的高感度而限制了在炸药领域的广泛应用。为制备高能量和高安全性的CL-20/Al含能复合材料,采用Pickering乳液法制备了空心球形CL-20/n-Al/F2605(氟橡胶)复合物,并对Picker... 高能量、高爆热的六硝基六氮杂异伍兹烷(CL-20)/Al复合物由于自身的高感度而限制了在炸药领域的广泛应用。为制备高能量和高安全性的CL-20/Al含能复合材料,采用Pickering乳液法制备了空心球形CL-20/n-Al/F2605(氟橡胶)复合物,并对Pickering乳液稳定性、复合物表面结构、热分解、燃烧及安全性能进行了分析。结果显示:当2 mL乙酸乙酯中溶解的CL-20固体质量为0.10~0.14 g、油水质量比在1:5~1:7之间、超声时间小于30 min、静置时间小于120 min时,形成的乳液稳定性好。该复合物表面结构粗糙,中位径d_(50)为73.17μm,各组分复合均匀。复合物的热分解峰温和活化能分别为236.7℃、164.6 kJ/mol,n-Al和F2605降低了CL-20分解过程中21.2%的活化能。复合物平均线性燃速为7.14 cm/s;特性落高H_(50)为39.5 cm,和原料CL-20相比提升了26.5 cm,安全性能得到提高。 展开更多
关键词 六硝基六氮杂异伍兹烷(CL-20) 纳米铝粉(n-al) 微球 Pickering乳液
下载PDF
Mn/Fe比对Al-Mg-Si合金组织和性能的影响
5
作者 刘雅婷 李元东 +3 位作者 刘文憬 王梓臣 罗晓梅 毕广利 《铸造》 CAS 2024年第5期587-595,共9页
以Al-Mg-Si合金为研究对象,采用金属型铸造研究Mn/Fe比对其组织和性能的影响。结果表明:Al-Mg-Si铸态合金组织中枝晶间存在α-Al基体和大量析出相,主要以Mg_(2)Si相为主,还存在少量的共晶Si相、AlFeSi相和Al(FeMn)Si相。随Mn/Fe比的增大... 以Al-Mg-Si合金为研究对象,采用金属型铸造研究Mn/Fe比对其组织和性能的影响。结果表明:Al-Mg-Si铸态合金组织中枝晶间存在α-Al基体和大量析出相,主要以Mg_(2)Si相为主,还存在少量的共晶Si相、AlFeSi相和Al(FeMn)Si相。随Mn/Fe比的增大,合金中的晶粒逐渐变得细小圆整,且由树枝晶向等轴晶发生转变。Mn可以促进铝合金中针状的β-AlFeSi相向骨骼状、颗粒状或块状的α-Al(FeMn)Si相的转变。当Mn/Fe比为0.5时,合金的热导率达到最大值181.08 W·m^(-1)·K^(-1)。当Mn/Fe比为1.0时,合金的晶粒尺寸最小且具有最佳的力学性能,抗拉强度、伸长率和硬度相较于Mn/Fe为0.2时分别提升17.45%、49.57%和27.48%,达到167.35 MPa、17.23%、HV 62.86。 展开更多
关键词 al-MG-SI合金 Mn/Fe比 金属型铸造 力学性能 热导率
下载PDF
Effect of melt-to-solid volume ratio and preheating temperature on Mg/Al bimetals interface by centrifugal casting 被引量:2
6
作者 Morteza Sarvari Mehdi Divandari +1 位作者 Hassan Saghafan Sina Ghaemi Khiavi 《China Foundry》 SCIE CAS CSCD 2023年第3期234-240,共7页
Compound casting is an efficient method for bonding dissimilar metals,in which a dramatic reaction can occur between the melt and solid.The centrifugal casting process,a type of compound casting,was applied to cast Al... Compound casting is an efficient method for bonding dissimilar metals,in which a dramatic reaction can occur between the melt and solid.The centrifugal casting process,a type of compound casting,was applied to cast Al/Mg dissimilar bimetals.Magnesium melt was poured at 700 °C,with melt-to-solid volume ratios(Vm/Vs) of 1.5 and 3,into a preheated hollow aluminum cylinder.The preheating temperatures of the solid part were 320,400,and 450 °C,and the constant rotational speed was 1,600 rpm.The cast parts were kept inside the casting machine until reaching the cooling temperature of 150 °C.The result showed that an increase in preheating temperature from 320 to 450 °C led to an enhanced reaction layer thickness.In addition,an increase in the Vm/Vs from 1.5 to 3 resulted in raising the interface thickness from 1.2 to 1.8 mm.Moreover,the interface was not continuously formed when a Vm/Vs of 3 was selected.In this case,the force of contraction overcame the resultant acting force on the interface.An interface formed at the volume ratio of 1.5 was examined using scanning electron microscopy(SEM) equipped with energy-dispersive X-ray spectroscopy(EDS),and the results demonstrated the formation of Al_(3)Mg_(2),Al_(12)Mg_(17) and(δ+Al_(12)Mg_(17)) eutectic structures in the interface. 展开更多
关键词 compound casting centrifugal casting Mg/al bimetal preheating temperature melt-to-solid volume ratio InTERFACE
下载PDF
磁控溅射镀膜技术在(Cr,Ti,Al)N涂层上的应用
7
作者 赵凡 项燕雄 +2 位作者 邹长伟 于云江 梁枫 《真空》 CAS 2024年第4期22-29,共8页
过渡金属氮化物硬质涂层在切削刀具、精密模具和机械零部件等领域有着广泛的应用。随着切削技术的进步和难加工材料的增多,硬质涂层已由传统的二元涂层向着三元、四元涂层不断发展。(Cr,Ti,Al)N四元涂层因其优异的综合性能而备受研究人... 过渡金属氮化物硬质涂层在切削刀具、精密模具和机械零部件等领域有着广泛的应用。随着切削技术的进步和难加工材料的增多,硬质涂层已由传统的二元涂层向着三元、四元涂层不断发展。(Cr,Ti,Al)N四元涂层因其优异的综合性能而备受研究人员的关注。本文从磁控溅射镀膜的基本原理和技术特点出发,介绍了制备(Cr,Ti,Al)N涂层常见的磁控溅射镀膜技术,分析了采用单质靶与合金靶沉积镀膜的效果及其各自的优缺点,研究了磁控溅射工艺参数对(Cr,Ti,Al)N涂层机械性能的影响,最后讨论了(Cr,Ti,Al)N梯度涂层的作用及其制备方法。本文可为设计(Cr,Ti,Al)N涂层制备工艺、改善(Cr,Ti,Al)N涂层性能提供理论参考与指导。 展开更多
关键词 (Cr Ti al)n涂层 磁控溅射 靶材选择 工艺参数 梯度涂层
下载PDF
Enhancement of catalytic and anti-carbon deposition performance of SAPO-34/ZSM-5/quartz films in MTA reaction by Si/Al ratio regulation 被引量:2
8
作者 Jiaxin Wu Chenxiao Wang +6 位作者 Xianliang Meng Haichen Liu Ruizhi Chu Guoguang Wu Weisong Li Xiaofeng Jiang Deguang Yang 《Chinese Journal of Chemical Engineering》 SCIE EI CAS CSCD 2023年第4期314-324,共11页
In order to further improve the catalytic performance of zeolite catalyst for methanol to aromatics(MTA)technology, the double-tier SAPO-34/ZSM-5/quartz composite zeolite films were successfully synthesized via hydrot... In order to further improve the catalytic performance of zeolite catalyst for methanol to aromatics(MTA)technology, the double-tier SAPO-34/ZSM-5/quartz composite zeolite films were successfully synthesized via hydrothermal crystallization. The Si/Al ratio of SAPO-34 film was used as the only variable to study this material. The composite zeolite material with 0.6Si/Al ratio of SAPO-34 has the largest mesoporous specific surface area and the most suitable acid distribution. The catalytic performance for the MTA process showed that 0.6-SAPO-34/ZSM-5/quartz film has as high as 50.3% benzene-toluenexylene selectivity and 670 min lifetime. The MTA reaction is carried out through the path we designed to effectively avoid the hydrocarbon pool circulation of ZSM-5 zeolite, so as to improve the aromatics selectivity and inhibit the occurrence of deep side reactions to a great extent. The coke deposition behavior was monitored by thermogravimetric analysis and gas chromatograph/mass spectrometer, it is found that with the increase of Si/Al ratio, the active intermediates changed from low-substituted methylbenzene to high-substituted methylbenzene, which led to the rapid deactivation of the catalyst. This work provides a possibility to employ the synergy effect of composite zeolite film synthesizing anti-carbon deposition catalyst in MTA reaction. 展开更多
关键词 Composite zeolite film Methanol to aromatics Anti-carbon deposition Si/al ratio Hydrocarbon pool circulation mechanism
下载PDF
Maize straw application as an interlayer improves organic carbon and total nitrogen concentrations in the soil profile: A four-year experiment in a saline soil 被引量:1
9
作者 CHANG Fang-di WANG Xi-quan +7 位作者 SONG Jia-shen ZHANG Hong-yuan YU Ru WANG Jing LIU Jian WANG Shang JI Hong-jie LI Yu-yi 《Journal of Integrative Agriculture》 SCIE CAS CSCD 2023年第6期1870-1882,共13页
Soil salinization is a critical environmental issue restricting agricultural production.Deep return of straw to the soil as an interlayer (at 40 cm depth) has been a popular practice to alleviate salt stress.However,t... Soil salinization is a critical environmental issue restricting agricultural production.Deep return of straw to the soil as an interlayer (at 40 cm depth) has been a popular practice to alleviate salt stress.However,the legacy effects of straw added as an interlayer at different rates on soil organic carbon (SOC) and total nitrogen (TN) in saline soils still remain inconclusive.Therefore,a four-year (2015–2018) field experiment was conducted with four levels (i.e.,0,6,12and 18 Mg ha~(–1)) of straw returned as an interlayer.Compared with no straw interlayer (CK),straw addition increased SOC concentration by 14–32 and 11–57%in the 20–40 and 40–60 cm soil layers,respectively.The increases in soil TN concentration (8–22 and 6–34%in the 20–40 and 40–60 cm soil layers,respectively) were lower than that for SOC concentration,which led to increased soil C:N ratio in the 20–60 cm soil depth.Increases in SOC and TN concentrations in the 20–60 cm soil layer with straw addition led to a decrease in stratification ratios (0–20 cm:20–60 cm),which promoted uniform distributions of SOC and TN in the soil profile.Increases in SOC and TN concentrations were associated with soil salinity and moisture regulation and improved sunflower yield.Generally,compared with other treatments,the application of 12 Mg ha~(–1) straw had higher SOC,TN and C:N ratio,and lower soil stratification ratio in the2015–2017 period.The results highlighted that legacy effects of straw application as an interlayer were maintained for at least four years,and demonstrated that deep soil straw application had a great potential for improving subsoil fertility in salt-affected soils. 展开更多
关键词 straw addition InTERLAYER soil organic carbon soil nitrogen C:n ratio saline soil
下载PDF
Lateral root elongation in maize is related to auxin synthesis and transportation mediated by N metabolism under a mixed NO_(3)^(–) and NH_(4)^(+) supply
10
作者 Peng Wang Lan Yang +4 位作者 Xichao Sun Wenjun Shi Rui Dong Yuanhua Wu Guohua Mi 《Journal of Integrative Agriculture》 SCIE CAS CSCD 2024年第3期1048-1060,共13页
A mixed nitrate (NO_(3)^(–)) and ammonium (NH_(4)^(+)) supply can promote root growth in maize (Zea mays),however,the changes in root morphology and the related physiological mechanism under different N forms are sti... A mixed nitrate (NO_(3)^(–)) and ammonium (NH_(4)^(+)) supply can promote root growth in maize (Zea mays),however,the changes in root morphology and the related physiological mechanism under different N forms are still unclear.Here,maize seedlings were grown hydroponically with three N supplied in three different forms (NO_(3)^(–)only,75/25 NO_(3)^(–)/NH_(4)^(+)and NH_(4)^(+)only).Compared with sole NO_(3)^(–)or NH_(4)^(+),the mixed N supply increased the total root length of maize but did not affect the number of axial roots.The main reason was the increased total lateral root length,while the average lateral root (LR) length in each axle was only slightly increased.In addition,the average LR density of 2nd whorl crown root under mixed N was also increased.Compared with sole nitrate,mixed N could improve the N metabolism of roots (such as the N influx rate,nitrate reductase (NR) and glutamine synthase (GS)enzyme activities and total amino content of the roots).Experiments with exogenously added NR and GS inhibitors suggested that the increase in the average LR length under mixed N was related to the process of N assimilation,and whether the NR mediated NO synthesis participates in this process needs further exploration.Meanwhile,an investigation of the changes in root-shoot ratio and carbon (C) concentration showed that C transportation from shoots to roots may not be the key factor in mediating lateral root elongation,and the changes in the sugar concentration in roots further proved this conclusion.Furthermore,the synthesis and transportation of auxin in axial roots may play a key role in lateral root elongation,in which the expression of ZmPIN1B and ZmPIN9 may be involved in this pathway.This study preliminarily clarified the changes in root morphology and explored the possible physiological mechanism under a mixed N supply in maize,which may provide some theoretical basis for the cultivation of crop varieties with high N efficiency. 展开更多
关键词 MAIZE nO_(3)^(–)/nH_(4)^(+)ratio lateral root elongation n assimilation indole-3-acetic acid
下载PDF
血浆NGAL、尿NAG及尿RBP在诊断早期糖尿病肾脏疾病中的价值 被引量:1
11
作者 赵晓静 韩书光 +3 位作者 李贝贝 陈聚盛 邓晨霞 刘倩倩 《检验医学与临床》 CAS 2024年第1期57-60,64,共5页
目的探讨血浆中性粒细胞明胶酶相关脂质运载蛋白(NGAL)、尿N-乙酰-β-D-氨基葡萄糖苷酶(NAG)和尿视黄醇结合蛋白(RBP)在诊断早期糖尿病肾脏疾病(DKD)中的价值。方法选取2021年5月至2023年3月在上海市浦东新区公利医院内分泌科确诊的2型... 目的探讨血浆中性粒细胞明胶酶相关脂质运载蛋白(NGAL)、尿N-乙酰-β-D-氨基葡萄糖苷酶(NAG)和尿视黄醇结合蛋白(RBP)在诊断早期糖尿病肾脏疾病(DKD)中的价值。方法选取2021年5月至2023年3月在上海市浦东新区公利医院内分泌科确诊的2型糖尿病(T2DM)患者227例作为研究对象,根据尿微量清蛋白/肌酐比值(UACR)进一步分为正常蛋白尿(NA)组、微量蛋白尿(MA)组、大量蛋白尿(HA)组,选取88例体检健康者作为对照组。检测各组UACR、NGAL、NAG、RBP、血糖、肾功能水平。分析NGAL、NAG、RBP水平与DKD的相关性,采用受试者工作特征(ROC)曲线分析各项指标诊断早期DKD的价值。结果根据UACR水平分组,NA组97例,MA组73例,HA组57例。NA组、MA组和HA组的NGAL、NAG、RBP水平高于对照组,并且HA组>MA组>NA组,差异均有统计学意义(P<0.05)。Pearson相关分析发现,NGAL、NAG、RBP水平与UACR、尿素氮(BUN)、血肌酐(SCr)、光抑素C(CysC)均呈正相关(P<0.05)。ROC曲线分析结果显示,NGAL、NAG、RBP及三者联合检测诊断DKD的曲线下面积(AUC)依次为0.854、0.788、0.830、0.929;单项检测时NGAL的灵敏度(82.3%)较高,NGAL、NAG和RBP联合检测时诊断效能最大(AUC=0.929)。结论血浆NGAL、尿NAG、尿RBP水平与DKD患者肾脏损伤程度密切相关。三者联合检测可发挥其最大诊断效能,为早期DKD的诊断提供新的方法。 展开更多
关键词 中性粒细胞明胶酶相关脂质运载蛋白 n-乙酰-Β-D-氨基葡萄糖苷酶 视黄醇结合蛋白 糖尿病肾脏疾病 尿微量清蛋白/肌酐比值
下载PDF
Humic Acid Effects on Reducing Corn Leaf Burn Caused by Foliar Spray of Urea-Ammonium Nitrate at Different Humic Acid/Urea-Ammonium Nitrate Ratios
12
作者 Xinhua Yin 《Open Journal of Soil Science》 2024年第3期180-189,共10页
Technologies for reducing corn leaf burn caused by foliar spray of urea-ammonium nitrate (UAN) during the early growing season are limited. A field experiment was carried out to evaluate the effects of humic acid on c... Technologies for reducing corn leaf burn caused by foliar spray of urea-ammonium nitrate (UAN) during the early growing season are limited. A field experiment was carried out to evaluate the effects of humic acid on corn leaf burn caused by foliar spray of undiluted UAN solution on corn canopy at Jackson, TN in 2018. Thirteen treatments of the mixtures of UAN and humic acid were evaluated at V6 of corn with different UAN application rates and different UAN/humic acid ratios. Leaf burn during 1 2, 3, 4, 5, 6, 7, and 14 days after UAN foliar spray significantly differed between with or without humic acid addition. The addition of humic acid to UAN significantly reduced leaf burn at each UAN application rate (15, 25, and 35 gal/acre). The reduction of leaf burn was enhanced as the humic acid/UAN ratio went up from 10% to 30%. Leaf burn due to foliar application of UAN became severer with higher UAN rates. The linear regression of leaf burn 14 days after application with humic acid/UAN ratio was highly significant and negative. However, the linear regression of leaf burn 14 days after application with the UAN application rate was highly significant and positive. In conclusion, adding humic acid to foliar-applied UAN is beneficial for reducing corn leaf burn during the early growing season. 展开更多
关键词 Humic Acid Urea-Ammonium nitrate CORn Leaf Burn n rate ratio
下载PDF
硝酸四氨合铜对n-Al/MoO_(3)纳米铝热体系反应特性的影响
13
作者 刘平 雷钫琴 +1 位作者 余杰 刘旭文 《爆破器材》 CAS CSCD 北大核心 2024年第5期44-49,54,共7页
为了提高n-Al/MoO_(3)纳米铝热体系的增压能力,改善能量释放性能,合成了高能产气组分硝酸四氨合铜(TACN),并将TACN复合入n-Al/MoO_(3)体系中。利用扫描电子显微镜(SEM)、X-射线衍射(XRD)技术研究了复合材料的形貌和微观结构。采用差示... 为了提高n-Al/MoO_(3)纳米铝热体系的增压能力,改善能量释放性能,合成了高能产气组分硝酸四氨合铜(TACN),并将TACN复合入n-Al/MoO_(3)体系中。利用扫描电子显微镜(SEM)、X-射线衍射(XRD)技术研究了复合材料的形貌和微观结构。采用差示扫描量热仪-热重分析(DSC-TG)联用技术探讨了各体系的热反应路径。使用高速摄像机和密闭爆发器分析了纳米铝热体系的火焰增长与传播和压力输出特性,评估了TACN的加入对n-Al/MoO_(3)体系的能量释放速率和增压性能的影响。研究结果表明:n-Al/MoO_(3)体系中加入的TACN能够在铝热反应的温度前放热分解,有效活化纳米铝与金属氧化物间的界面,从而降低体系的初始反应峰温度。此外,TACN的加入显著增强了n-Al/MoO_(3)体系的能量释放和压力输出性能。当TACN的质量分数为6%时,n-Al/MoO_(3)体系的火焰增长速率和火焰传播速率分别增加了32%和30%,峰值压力和增压速率分别提高了26%和70%。综上所述,TACN可提升n-Al/MoO_(3)纳米铝热体系的压力输出,并调控体系的能量释放性能。 展开更多
关键词 n-al/MoO_(3) 高能产气组分 纳米铝热剂 含能配合物
下载PDF
添加Sn对不同Mg/Si比Al-Mg-Si合金时效硬化和析出行为的影响
14
作者 涂文斌 唐建国 +2 位作者 王善林 马乐航 赵言 《材料工程》 EI CAS CSCD 北大核心 2023年第10期68-75,共8页
采用硬度测试和透射电镜研究Sn对不同Mg/Si比Al-Mg-Si合金时效硬化与析出行为的影响。结果表明:添加Sn虽然增加了低Mg/Si比合金峰值时效的析出相密度,但也降低了β″相的析出速度,从而降低了低Mg/Si比合金峰时效前的硬化速度和峰时效硬... 采用硬度测试和透射电镜研究Sn对不同Mg/Si比Al-Mg-Si合金时效硬化与析出行为的影响。结果表明:添加Sn虽然增加了低Mg/Si比合金峰值时效的析出相密度,但也降低了β″相的析出速度,从而降低了低Mg/Si比合金峰时效前的硬化速度和峰时效硬度。过时效阶段,含Sn合金的高析出相密度提高了低Mg/Si比合金过时效硬度。对于高Mg/Si比合金,添加Sn不仅增加合金的析出相密度,同时也提高了β″相的析出速度,从而增加了合金的硬化速度和峰时效硬度。 展开更多
关键词 al-MG-SI合金 Mg/Si比 时效析出 Sn添加
下载PDF
Cu含量以及Cu/Mg比对Al-Si-Cu-Mg合金组织和力学性能的影响
15
作者 顾琪 周鹏飞 《铸造》 CAS 2024年第2期180-186,共7页
研究了Cu含量和Cu/Mg比对Al-Si-Cu-Mg合金组织和力学性能的影响。结果表明Al-Si-Cu-Mg合金凝固组织是否形成Mg_(2)Si、Q-Al_(5)Cu_(2)Mg_(8)Si_(6)以及θ-Al_(2)Cu取决于Cu含量以及Cu/Mg比。当Cu/Mg比相对低时形成Mg_(2)Si中间相,而Cu/M... 研究了Cu含量和Cu/Mg比对Al-Si-Cu-Mg合金组织和力学性能的影响。结果表明Al-Si-Cu-Mg合金凝固组织是否形成Mg_(2)Si、Q-Al_(5)Cu_(2)Mg_(8)Si_(6)以及θ-Al_(2)Cu取决于Cu含量以及Cu/Mg比。当Cu/Mg比相对低时形成Mg_(2)Si中间相,而Cu/Mg比高时则倾向于生成Q-Al_(5)Cu_(2)Mg_(8)Si_(6)和θ-Al_(2)Cu相。当Cu/Mg比相同时,高Cu含量和高Mg含量都会促进Q相θ相的形成。通过观察T6热处理后的组织发现Cu含量以及Cu/Mg比控制了初生相的溶解以及析出相的形成,从而影响合金的强度与韧性。通过控制Cu含量及Cu/Mg比使Al-9Si-2Cu-0.5Mg合金中析出较少数量的初生相,再通过热处理析出大量的Q′强化相,使合金具有较高的强度和相对适中的伸长率。 展开更多
关键词 al-Si-Cu-Mg CU含量 Cu/Mg比 组织 力学性能
下载PDF
磁控溅射Ti-Al-N复合膜的摩擦磨损性能分析
16
作者 陆昆 杨海 《宁德师范学院学报(自然科学版)》 2023年第2期138-142,共5页
采用真空磁控溅射技术的方法制备了不同Al质量分数的Ti-Al-N薄膜,分别研究了室温及高温下不同Al质量分数的Ti-Al-N薄膜的摩擦磨损性能.研究结果表明,Al质量分数和温度都对薄膜的摩擦磨损性能产生较大的影响.室温时,当Al质量分数为49.97%... 采用真空磁控溅射技术的方法制备了不同Al质量分数的Ti-Al-N薄膜,分别研究了室温及高温下不同Al质量分数的Ti-Al-N薄膜的摩擦磨损性能.研究结果表明,Al质量分数和温度都对薄膜的摩擦磨损性能产生较大的影响.室温时,当Al质量分数为49.97%时,薄膜的平均摩擦系数最小,为0.772 3;高温条件下,薄膜的摩擦系数显著低于室温条件下,当Al质量分数为39.51%时,平均摩擦系数最小,为0.379 2. 展开更多
关键词 Ti-al-n薄膜 真空磁控溅射技术 摩擦磨损 al原子 摩擦系数
下载PDF
挤压比对车用Al-5.5Mg-1.2Si-0.5Cu-0.2Mn合金微观组织的影响研究 被引量:1
17
作者 崔秀虹 吴庆玲 《山西冶金》 CAS 2023年第11期32-33,36,共3页
以Al-Si-Mg合金作为测试材料,挤压成型后对其实施T6时效处理,对比了不同挤压比下Al-5.5Mg-1.2Si-0.5Cu-0.2Mn合金显微组织变化。研究结果表明:所有挤压比下合金组织中都形成了大量第二相颗粒,并且整体分布形态都较均匀,颗粒外形主要为... 以Al-Si-Mg合金作为测试材料,挤压成型后对其实施T6时效处理,对比了不同挤压比下Al-5.5Mg-1.2Si-0.5Cu-0.2Mn合金显微组织变化。研究结果表明:所有挤压比下合金组织中都形成了大量第二相颗粒,并且整体分布形态都较均匀,颗粒外形主要为短棒型与类球形结构;挤压比26.2时,合金得到最小的晶粒尺寸,此时形成了具有球型结构的Mg2Si析出相,形成了98.4%的再结晶组织,亚组织占比约1.5%。同时形成了更多的板形β′相,此时针形β″相的长度在18.5~46μm范围内。 展开更多
关键词 al-MG-SI合金 挤压比 微观组织 析出相
下载PDF
Al/N共掺杂TiO_(2)薄膜的制备及光学性能
18
作者 王泽文 赵莉 +1 位作者 蔺冬雪 王玉新 《半导体光电》 CAS 北大核心 2023年第1期87-91,共5页
采用溶胶-凝胶旋涂法(Sol-Gel Spin-Coating Method)制备了Al掺杂量为3.00at%,N掺杂量分别为6.00at%,7.00at%,8.00at%和9.00at%的Al/N共掺杂TiO_(2)薄膜样品。对样品测试的结果表明,共掺杂样品依旧保留了TiO_(2)的基本结构,并且Al/N共... 采用溶胶-凝胶旋涂法(Sol-Gel Spin-Coating Method)制备了Al掺杂量为3.00at%,N掺杂量分别为6.00at%,7.00at%,8.00at%和9.00at%的Al/N共掺杂TiO_(2)薄膜样品。对样品测试的结果表明,共掺杂样品依旧保留了TiO_(2)的基本结构,并且Al/N共掺杂样品的晶粒尺寸有不同程度的减小,使样品表面得以修饰,变得更加均匀、平整。共掺杂样品吸收边都出现了不同程度的红移,在紫外光区以及可见光区的吸光性都有所增强。N掺杂量为7.00at%时,(101)衍射峰值最大,峰型最尖锐,所得到的TiO_(2)薄膜的光学性能最好。共掺杂后的样品与本征TiO_(2)相比带隙值都有所减小,且最小值为2.873 eV。以上结果表明Al/N共掺杂TiO_(2)薄膜使其光学性能得到了改善。 展开更多
关键词 al/n共掺杂 TiO_(2)薄膜 光学性能 溶胶-凝胶法
下载PDF
Effects of the combined application of organic and chemical nitrogen fertilizer on soil aggregate carbon and nitrogen:A 30-year study 被引量:1
19
作者 BAI Jin-shun ZHANG Shui-qing +5 位作者 HUANG Shao-min XU Xin-peng ZHAO Shi-cheng QIU Shao-jun HE Ping ZHOU Wei 《Journal of Integrative Agriculture》 SCIE CAS CSCD 2023年第11期3517-3534,共18页
To understand the long-term effects of combined organic and chemical nitrogen fertilization on soil organic C(SOC) and total N(TN), we conducted a 30-year field experiment with a wheat–maize rotation system on the Hu... To understand the long-term effects of combined organic and chemical nitrogen fertilization on soil organic C(SOC) and total N(TN), we conducted a 30-year field experiment with a wheat–maize rotation system on the Huang-HuaiHai Plain during 1990–2019. The experimental treatments consisted of five fertilizer regimes: no fertilizer(control), chemical fertilizer only(NPK), chemical fertilizer with straw(NPKS), chemical fertilizer with manure(NPKM), and 1.5 times the rate of NPKM(1.5NPKM). The NPK, NPKS, and NPKM treatments had equal N inputs. The crop yields were measured over the whole experimental duration. Soil samples were collected from the topsoil(0–10 and 10–20 cm) and subsoil(20–40 cm) layers for assessing soil aggregates and taking SOC and TN measurements. Compared with the NPK treatment, the SOC and TN contents increased significantly in both the topsoil(24.1–44.4% for SOC and 22.8–47.7% for TN) and subsoil layers(22.0–47.9% for SOC and 19.8–41.8% for TN) for the organically amended treatments(NPKS, NPKM and 1.5NPKM) after 30 years, while no significant differences were found for the average annual crop yields over the 30 years of the experiment. The 0–10 cm layer of the NPKS treatment and the 20–40 cm layer of the NPKM treatment had significantly higher macroaggregate fraction mass proportions(19.8 and 27.0%) than the NPK treatment. However, the 0–10 and 20–40 cm layers of the 1.5NPKM treatment had significantly lower macroaggregate fraction mass proportions(–19.2 and –29.1%) than the control. The analysis showed that the higher SOC and TN in the soil of organically amended treatments compared to the NPK treatment were related to the increases in SOC and TN protected in the stable fractions(i.e., free microaggregates and microaggregates within macroaggregates), in which the contributions of the stable fractions were 81.1–91.7% of the increase in SOC and 83.3–94.0% of the increase in TN, respectively. The relationships between average C inputs and both stable SOC and TN stocks were significantly positive with R2 values of 0.74 and 0.72(P<0.01) for the whole 40 cm soil profile, which indicates the importance of N for soil C storage. The results of our study provide key evidence that long-term combined organic and chemical nitrogen fertilization, while maintaining reasonable total N inputs, benefited soil C and N storage in both the topsoil and subsoil layers. 展开更多
关键词 soil aggregate fractions soil organic matter manure application straw return C:n ratio
下载PDF
偏压梯度TiAlN涂层对TC4钛合金振动与拉伸疲劳性能的影响与机理
20
作者 曹鑫 王静静 +3 位作者 李聪健 何卫锋 汪路路 何磊 《表面技术》 EI CAS CSCD 北大核心 2023年第10期376-383,共8页
目的 探究偏压梯度TiAlN涂层对基体疲劳性能的影响规律和疲劳损伤机理。方法 利用磁过滤阴极真空弧技术和连续改变偏压的沉积工艺,在TC4钛合金表面沉积了偏压梯度TiAlN涂层,并采用扫描电镜、轮廓仪、纳米压痕和划痕仪表征测试了TiAlN涂... 目的 探究偏压梯度TiAlN涂层对基体疲劳性能的影响规律和疲劳损伤机理。方法 利用磁过滤阴极真空弧技术和连续改变偏压的沉积工艺,在TC4钛合金表面沉积了偏压梯度TiAlN涂层,并采用扫描电镜、轮廓仪、纳米压痕和划痕仪表征测试了TiAlN涂层的微观结构和内应力、表面硬度、膜基结合力等基本力学性能。对TiAlN涂层试件的振动和拉伸疲劳性能分别进行了考核,通过观察试件疲劳断口形貌,探究了偏压梯度TiAlN涂层/基体的疲劳损伤机理。结果 TiAlN涂层中Al元素含量沿深度方向一直在降低,偏压工艺成功制备出梯度结构涂层。偏压梯度TiAlN涂层的内应力为压缩状态,数值为(2.66±0.23) GPa,显著低于对应恒压涂层(-200V)。偏压梯度TiAlN涂层试件平均振动强度和拉伸疲劳强度分别为370.90、377.90 MPa,前者相对于TC4基体提高了47.7%,后者几乎保持不变。结论 TiAlN涂层内部存在残余压应力,具有一定抗裂纹萌生能力,TC4钛合金表面制备偏压梯度TiAlN涂层后,两种受载类型下的疲劳裂纹源均位于涂层与基体界面处。振动受载时,涂层中梯度结构抑制了裂纹的扩展,疲劳强度提高;拉伸受载时,TiAlN涂层部分发生破碎,抑制裂纹萌生与促进裂纹扩展两种机制同时存在,疲劳强度几乎不变。 展开更多
关键词 Ti al n涂层 偏压梯度结构 TC4钛合金 疲劳性能 损伤机理
下载PDF
上一页 1 2 161 下一页 到第
使用帮助 返回顶部