The growth of intermetallic compounds at the interface between solid Al and Fe and the effects of intermetallic compound layers on the interfacial bonding of clad materials were investigated. The results showed that t...The growth of intermetallic compounds at the interface between solid Al and Fe and the effects of intermetallic compound layers on the interfacial bonding of clad materials were investigated. The results showed that the interface between the solid Fe and Al formed by heat-treatment consisted of Fe2Al5 and FeAl3 intermetallic compound layers, which deteriorated the interfacial bonding strength. Fractures occurred in the intermetallic compound layer during the shear testing. The location of the fracture depended on the defects of microcracks or voids in the intermetallic compound layers. The microcracks in the intermetallic compound layer were caused by the mismatch of thermal expansion coefficients of materials during cooling, and the voids were consistent with the Kirkendall effect. The work will lay an important foundation for welding and joining of aluminum and steel, especially for fabrication of Al-Fe clad materials.展开更多
Double glow plasma surface metallurgy technique was used to fabricate a Fe?Al?Cr?Nb alloyed layer onto the surface of the 45 steel. The microstructures and composition of th?eA Fl?eCr?Nb alloyed layer were analyzed by...Double glow plasma surface metallurgy technique was used to fabricate a Fe?Al?Cr?Nb alloyed layer onto the surface of the 45 steel. The microstructures and composition of th?eA Fl?eCr?Nb alloyed layer were analyzed by scanning electronic microscopy, X-ray diffraction and energy dispersive spectroscopy. The results indicate thatthe 20 μm alloyed layer is homogeneous and compact. The alloyed elements exhibit a gradient distribution along the cross section. Microhardness and nanoindentation tests imply that the surface hardness of the alloyed layer reaches HV 580, which is almost 2.8 times that of the substrate. Compared with the substrate, the alloyed layer has a much smaller displacement and a larger elastic modulus. According to the friction and wear tests at room temperature, the? FeAl?Cr?Nb alloyed layer has lower friction coefficient and less wear mass, implying that the Fe?Al?Cr?Nb alloyed layer can effectively improve the surface hardness and wear resistance of the substrate.展开更多
Scanning electron microscopy and X-ray energy dispersive spectrum analysis show that the clusters of intermetallic AlFeSi particle are distributed on or near the aluminum foil stock surfaces heterogeneously. 3D finite...Scanning electron microscopy and X-ray energy dispersive spectrum analysis show that the clusters of intermetallic AlFeSi particle are distributed on or near the aluminum foil stock surfaces heterogeneously. 3D finite element modeling shows that these clusters of hard particles induce the fracture of the nano-scale lubricant oil film at first and further lead to severe deformation in the nearby aluminum foil substrate along the rolling direction. Consequently, the optical property in this region differs from that in the surroundings, resulting in surface defects.展开更多
A thermodynamic assessment of the Al-Fe-Mn-Si quaternary system and its subsystems was performed by the Calphad method. First, the Al-Fe-Si ternary description was deeply revised by considering the most recent experim...A thermodynamic assessment of the Al-Fe-Mn-Si quaternary system and its subsystems was performed by the Calphad method. First, the Al-Fe-Si ternary description was deeply revised by considering the most recent experimental investigations and employing new models to ternary compounds. Significant improvements were made on the calculated liquidus projection over the entire compositional range, especially in the Al-rich corner. The Al-Mn-Si system was refined in the Al-rich region by adopting new models for the two ternary compounds, a-AlMnSi and β-AlMnSi. The extended solubility of the a-AlMnSi phase into the Al-Fe-Mn-Si quaternary system was modeled to reproduce the phase equilibria in the Al-rich region. Special cares were taken in order to prevent a-AlMnSi from becoming stable in the Al-Fe-Si ternary system. The obtained thermodynamic descriptions were then implemented into the TCAL database, and extensively validated with phase equilibrium calculations and solidification simulations against experimental data/information from commercial aluminum alloys. The updated TCAL database can reliably predict the phase formation in Al-Fe-Si- and Al-Fe-Mn-Si-based aluminum alloys.展开更多
Ce element was introduced to modify Al−2%Fe(mass fraction)binary alloy.The microstructures,crystallization behavior,electrical/thermal conductivities and mechanical properties of these alloys were systematically inves...Ce element was introduced to modify Al−2%Fe(mass fraction)binary alloy.The microstructures,crystallization behavior,electrical/thermal conductivities and mechanical properties of these alloys were systematically investigated.The results indicated that the appropriate Ce addition decreased the recalescence temperature and growth temperature of Al−Fe eutectic structure,improved the morphology and distribution of Fe-containing phase,and simultaneously increased the conductivity and mechanical properties.The annealed treatment improved the thermal conductivity of these alloys due to the decreasing concentration of point defects.Rolling process further broke up the coarser Fe-containing phases into finer particles and made the secondary phases uniformly distributed in theα(Al)matrix.After subsequent annealing treatment and rolling deformation,the thermal conductivity,ultimate tensile strength and hardness of the Al−2%Fe−0.3%Ce(mass fraction)alloy reached 226 W/(m·K),(182±1.4)MPa and HBW(49.5±1.7),respectively.展开更多
Al-Si-Fe based alloys are attractive light-weight structural materials for automotive engine components because of their high wear resistance, low density and low thermal expansion. Al-17Si 5Fe-2Cu-lMg-lNi-lZr alloys ...Al-Si-Fe based alloys are attractive light-weight structural materials for automotive engine components because of their high wear resistance, low density and low thermal expansion. Al-17Si 5Fe-2Cu-lMg-lNi-lZr alloys were produced in compact form by a spark plasma sintering （SPS） technique using gas atomized powders. The mean grain size of the compact was 530 nm, and fine equiaxed grains and uniformly distributed precipitates were observed in the compact. The compressive deformation behavior of the SPSed materials was examined at various temperatures and strain rates. All the true stress-true strain curves showed steady state flow after reaching peak stress. The peak stress decreased with increasing test temperature and decreasing strain rate. In the deformed specimens, the equiaxed grain morphology and the dislocation microstructure within the equiaxed grains were observed. These facts strongly indicated the occurrence of dynamic recrystallization during high temperature deformation of the present alloy.展开更多
Microstructural evolution of a cold-rolled Al-Mn-Fe-Si alloy during annealing was studied. Except the as-cast variant, two other different homogenizations were considered, one gave a high density of fine dispersiods p...Microstructural evolution of a cold-rolled Al-Mn-Fe-Si alloy during annealing was studied. Except the as-cast variant, two other different homogenizations were considered, one gave a high density of fine dispersiods providing a considerable Zener drag influencing the softening behavior while the other gave a lower density of coarser dispersoid structure providing a much smaller drag effect. The gradual microstructural evolutions during annealing for the three variants were captured by interrupting annealing at different time. Effects of microchemistry state on recrystallization kinetics, recrystallized grain structure and texture were characterized by EBSD. It is demonstrated that the actual softening kinetics, final microstructure and texture are a result of delicate balance between processing condition and microchemistry state. Strong concurrent precipitation takes place in the case with high concentration of Mn in solid solution, which suppresses nucleation and retards recrystallization and finally leads to grain structure of coarse elongated grains dominated by a P texture component together with a ND-rotated cube component. On the contrary, when solute content of Mn is low and pre-existing dispersoids are relatively coarser, faster recrystallization kinetics is exhibited together with an equiaxed grain structure with mainly cube texture.展开更多
Thermal stability of nanocrystalline Al-10wt.%Fe-5wt.%Cr bulk alloy was investigated.The initial micro-grained mixture of powders was processed for 100 h using mechanical alloying(MA)to produce nano-grained alloy.The ...Thermal stability of nanocrystalline Al-10wt.%Fe-5wt.%Cr bulk alloy was investigated.The initial micro-grained mixture of powders was processed for 100 h using mechanical alloying(MA)to produce nano-grained alloy.The processed powders were sintered using high frequency induction heat sintering(HFIHS).The microstructures of the processed alloy in the form of powders and bulk samples were investigated using XRD,FESEM and HRTEM.Microhardness and compression tests were conducted on the bulk samples for evaluating their mechanical properties.To evaluate the thermal stability of the bulk samples,they were experimented at 573,623,673 and 723 K under compression load at strain rates of 1×10^-1 and 1×10^-2 s^-1.The annealed samples exhibited a significant increase in their microhardness value of 2.65 GPa when being annealed at 723 K,as compared to 2.25 GPa of the as-sintered alloy.The bulk alloy revealed compressive strengths of 520 MPa and 450 MPa at 300 K and 723 K,respectively,when applying a strain rate of 1×10^-1 s^-1.The microstructural stability of the bulk alloy was ascribed to the formation of iron and chromium containing phases with Al such as Al6Fe,Al13Fe4 and Al13Cr2,in addition to the supersaturated solid solution(SSSS)of Cr and Fe in Al matrix.展开更多
Porous FeAl-based intermetallics were fabricated by thermal explosion（TE） from Fe and Al powders. The effects of sintering temperature on phase constitution, pore structure and oxidation resistance of porous Fe-Al i...Porous FeAl-based intermetallics were fabricated by thermal explosion（TE） from Fe and Al powders. The effects of sintering temperature on phase constitution, pore structure and oxidation resistance of porous Fe-Al intermetallics were systematically investigated. Porous Fe-Al materials with high open porosity（65%） are synthesized via a low-energy consumption method of TE at a temperature of 636 ℃ and FeAl intermetallic is evolved as dominant phase in sintered materials at 1000 ℃. The porous materials are composed of interconnected skeleton, large pores among skeleton and small pores in the interior of skeleton. The interstitial pores in green powder compacts are the important source of large pores of porous Fe-Al intermetallics, and the in-situ pores from the melting and flowing of aluminum powders are also significant to the formation of large pores. Small pores are from the precipitation of Fe-Al intermetallics particles. In addition, the porous specimens exhibit high resistance to oxidation at 650 ℃ in air.展开更多
The formation of nanoporous Pd was studied by electro-chemical dealloying a rapidly-quenched Al70Pd17Fe13 quasicrystal alloy in dilute NaCl aqueous solution,and the electro-catalytic activity of the nanoporous Pd towa...The formation of nanoporous Pd was studied by electro-chemical dealloying a rapidly-quenched Al70Pd17Fe13 quasicrystal alloy in dilute NaCl aqueous solution,and the electro-catalytic activity of the nanoporous Pd towards methanol electro-oxidation was evaluated by cyclic voltammetry in 1 mol/L KOH solution.XRD and TEM analyses revealed that nano-decomposition of quasicrystal grains occurred in the initial stage of dealloying,and the fully dealloyed sample was composed of FCC-Pd phase.Scanning electron microscopy observation indicated that a maze-like nanoporous pattern was formed in the dealloyed sample,consisting of percolated pores of 5.20 nm in diameter in a skeleton of randomly-orientated Pd nano-ligaments with a uniform thickness of^5 nm.A retention of^12 at.%Al in the Pd nano-ligments was determined by energy dispersive X-ray spectroscopy(EDS).The nanoporous Pd demonstrated obvious electro-catalytic activity towards methanol electro-oxidation in alkaline environment.展开更多
The effects of Fe content on the microstructure,phase constituents and microhardness of the as-cast,800℃or 1000℃-annealed Al_(7)Cr_(20)Fe_(x)Ni_(73)−x(x=13−66)alloys were investigated.Not all these alloys are compos...The effects of Fe content on the microstructure,phase constituents and microhardness of the as-cast,800℃or 1000℃-annealed Al_(7)Cr_(20)Fe_(x)Ni_(73)−x(x=13−66)alloys were investigated.Not all these alloys are composed of the single FCC phase.The BCC and B2 phases are found.It is confirmed that the BCC phase in the Al7Cr20Fe66Ni7 alloy is transformed from the FCC phase at about 900℃ during cooling.While in the 800℃-annealed Al7Cr20Fe60Ni13 alloy,the FCC phase is stable and the hardness decreases.After annealing at 1000℃,for the precipitation of the B2 particles,the Al content in the FCC phase decreases,which results in decreasing of the alloy hardness.Moreover,after annealing at 800℃,a small amount of Al-rich B2 particles precipitate at the phase boundary and some nanocrystal BCC phase precipitates in the FCC matrix,which increases the hardness of the Al_(7)Cr_(20)Fe_(x)Ni_(73)−x(x=41−49)alloys.These results will help to the composition design and processing design of the Al−Cr−Fe−Ni based high-entropy alloys.展开更多
The effect of iron addition on the microstructure, mechanical and magnetic properties of Al-matrix composite was studied. Mechanical mixing was used for the preparation of 0, 5%, 10% and 15% Fe-Al composites（mass fra...The effect of iron addition on the microstructure, mechanical and magnetic properties of Al-matrix composite was studied. Mechanical mixing was used for the preparation of 0, 5%, 10% and 15% Fe-Al composites（mass fraction）. Mixtures of Al-Fe were compacted and sintered in a vacuum furnace at 600 °C for 1 h. X-ray diffraction（XRD） of the samples containing 5% and 10% Fe indicates the presence of Al and Fe peaks, while sample containing 15% Fe reveals Al and Al13Fe4 peaks. The results show that both densification and thermal conductivity of the composites decrease by increasing the iron content. The presence of iron in the composite improves the compressive strength and the hardness. The strengthening mechanism is associated with the grain refinement of the matrix and uniform distribution of the Fe particles, as well as the formation of Al13Fe4 intermetallic. The measured magnetization values are equal to 0.3816×10-3 A·m2/g for 5% Fe sample and increases up to 0.6597×10-3 A·m2/g for 10% Fe sample, then decreases to 0.0702×10-3 A·m2/g for 15% Fe sample. This can be explained by the formation of the diamagnetic Al13Fe4 intermetallic compound in the higher Fe content sample detected by XRD analysis.展开更多
Commercial pure aluminum and galvanized carbon steel were lap-welded using the weld-brazing(WB)technique.Three types of aluminum filler materials(4043,4047,and 5356) were used for WB.The joint strength and intermetall...Commercial pure aluminum and galvanized carbon steel were lap-welded using the weld-brazing(WB)technique.Three types of aluminum filler materials(4043,4047,and 5356) were used for WB.The joint strength and intermetallic compounds at the interface of three series of samples were analyzed and compared.Depending on the Si content,a variety of ternary Al-Fe-Si intermetallic compounds(IMCs) such as Fe_(4)(Al,Si)_(13),Fe_(2) Al_(8) Si(τ_(5)),and Fe_(2) Al_(9) Si_(2)(τ_(6)) were formed at the interface.Mg element in 5356 filler material cannot contribute to the formation of Al-Fe intermetallic phases due to the positive mixing enthalpy of Mg-Fe.The presence of Mg enhances the hot cracking phenomenon near the Al-Fe intermetallic compound at the interface.Zn coating does not participate in intermetallic formation due to its evaporation during WB.It was concluded that the softening of the base metal in the heat-affected zone rather than the IMCs determines the joint efficiency.展开更多
The effect of incorporating limited-diffusivity elements such as Fe and Ti on thermal stability of the nanocrystalline Al alloy was investigated.Al−10wt.%Fe and Al−10wt.%Fe−5wt.%Ti alloys were fabricated.The initial m...The effect of incorporating limited-diffusivity elements such as Fe and Ti on thermal stability of the nanocrystalline Al alloy was investigated.Al−10wt.%Fe and Al−10wt.%Fe−5wt.%Ti alloys were fabricated.The initial mixtures of powders were milled for 100 h in vacuum.The bulk samples were fabricated from the milled powders in a high frequency induction heat sintering(HFIHS)system.The milled powders and the bulk sintered samples were characterized by X-ray diffraction(XRD),Vickers microhardness,field emission scanning electron microscopy(FESEM-EDS)and transmission electron microscopy(TEM).The observations indicated that Fe and Ti were completely dispersed in the matrix to form a supersaturated solid solution(SSSS)with Al.Additionally,the inclusion of alloying elements led to an increase in hardness and yield strength of the alloy by 127%and 152%,respectively.The elevated temperature compression tests were carried out to evaluate the thermal stability of the alloys.The Al−10wt.%Fe−5wt.%Ti alloy revealed the optimum thermally stable behavior of the three alloys studied.The incorporation of Fe and Ti improved the thermal stability of the developed alloys through inhibiting the grain growth,hindering dissolution and growth of second phases(such as Al13Fe4 and Al13Ti),and forming a stable solid solution.展开更多
An experimental study has been carried out to investigate the influence of heat treatment at 300 ℃,450 ℃,550 ℃,650 ℃ and 800 ℃ on the microstructure and sliding wear behavior of Fe Al/WC intermetallic composite c...An experimental study has been carried out to investigate the influence of heat treatment at 300 ℃,450 ℃,550 ℃,650 ℃ and 800 ℃ on the microstructure and sliding wear behavior of Fe Al/WC intermetallic composite coatings produced by high velocity arc spraying (HVAS) and cored wires. The result shows, the main phases in both as sprayed and heat treated Fe Al/WC composite coatings are iron aluminide intermetallics (Fe 3Al+FeAl) and α as well as a little oxide (Al 2O 3) and carbides (WC, W 2C, Fe 2W 2C and Fe 6W 6C). After heat treated at 450-650 ℃, dispersion strengthening of Fe 2W 2C and Fe 6W 6C will lead to a rise in microhardness of the coatings. The microhardness is likely to be the most important factor which influences the sliding wear behavior of the coatings. Increasing the microhardness through heat treatment will improve the sliding wear resistance of the Fe Al/WC composite coatings.展开更多
基金Project(2011DFR50630)sponsored by the International S&T Cooperation of China
文摘The growth of intermetallic compounds at the interface between solid Al and Fe and the effects of intermetallic compound layers on the interfacial bonding of clad materials were investigated. The results showed that the interface between the solid Fe and Al formed by heat-treatment consisted of Fe2Al5 and FeAl3 intermetallic compound layers, which deteriorated the interfacial bonding strength. Fractures occurred in the intermetallic compound layer during the shear testing. The location of the fracture depended on the defects of microcracks or voids in the intermetallic compound layers. The microcracks in the intermetallic compound layer were caused by the mismatch of thermal expansion coefficients of materials during cooling, and the voids were consistent with the Kirkendall effect. The work will lay an important foundation for welding and joining of aluminum and steel, especially for fabrication of Al-Fe clad materials.
基金Project(51371097)supported by the National Natural Science Foundation of ChinaProject supported by the Priority Academic Program Development of Jiangsu Higher Education Institutions,China
文摘Double glow plasma surface metallurgy technique was used to fabricate a Fe?Al?Cr?Nb alloyed layer onto the surface of the 45 steel. The microstructures and composition of th?eA Fl?eCr?Nb alloyed layer were analyzed by scanning electronic microscopy, X-ray diffraction and energy dispersive spectroscopy. The results indicate thatthe 20 μm alloyed layer is homogeneous and compact. The alloyed elements exhibit a gradient distribution along the cross section. Microhardness and nanoindentation tests imply that the surface hardness of the alloyed layer reaches HV 580, which is almost 2.8 times that of the substrate. Compared with the substrate, the alloyed layer has a much smaller displacement and a larger elastic modulus. According to the friction and wear tests at room temperature, the? FeAl?Cr?Nb alloyed layer has lower friction coefficient and less wear mass, implying that the Fe?Al?Cr?Nb alloyed layer can effectively improve the surface hardness and wear resistance of the substrate.
基金Project(51074117)supported by the National Natural Science Foundation of ChinaProject(2009CDA044)supported by the Foundation for Distinguished Young Scientists of Hubei Province,ChinaProjects(201104493,20100471161)supported by the China Postdoctoral Science Foundation
文摘Scanning electron microscopy and X-ray energy dispersive spectrum analysis show that the clusters of intermetallic AlFeSi particle are distributed on or near the aluminum foil stock surfaces heterogeneously. 3D finite element modeling shows that these clusters of hard particles induce the fracture of the nano-scale lubricant oil film at first and further lead to severe deformation in the nearby aluminum foil substrate along the rolling direction. Consequently, the optical property in this region differs from that in the surroundings, resulting in surface defects.
文摘A thermodynamic assessment of the Al-Fe-Mn-Si quaternary system and its subsystems was performed by the Calphad method. First, the Al-Fe-Si ternary description was deeply revised by considering the most recent experimental investigations and employing new models to ternary compounds. Significant improvements were made on the calculated liquidus projection over the entire compositional range, especially in the Al-rich corner. The Al-Mn-Si system was refined in the Al-rich region by adopting new models for the two ternary compounds, a-AlMnSi and β-AlMnSi. The extended solubility of the a-AlMnSi phase into the Al-Fe-Mn-Si quaternary system was modeled to reproduce the phase equilibria in the Al-rich region. Special cares were taken in order to prevent a-AlMnSi from becoming stable in the Al-Fe-Si ternary system. The obtained thermodynamic descriptions were then implemented into the TCAL database, and extensively validated with phase equilibrium calculations and solidification simulations against experimental data/information from commercial aluminum alloys. The updated TCAL database can reliably predict the phase formation in Al-Fe-Si- and Al-Fe-Mn-Si-based aluminum alloys.
基金financially supported by the National Natural Science Foundation of China(No.52174363)the GDAS Project of Science and Technology Development,China(No.2019GDASYL-0203002)+2 种基金the Key Research and Development Program of Guangdong Province,China(No.2020B010186002)the Science and Technology Project of Zhaoqing City,China(Nos.2021C003,2018K006)the Development of Key Technologies for Material and Microstructure Control of High Thermal Conductivity Casting Aluminum Alloy,China(No.2014A030313221)。
文摘Ce element was introduced to modify Al−2%Fe(mass fraction)binary alloy.The microstructures,crystallization behavior,electrical/thermal conductivities and mechanical properties of these alloys were systematically investigated.The results indicated that the appropriate Ce addition decreased the recalescence temperature and growth temperature of Al−Fe eutectic structure,improved the morphology and distribution of Fe-containing phase,and simultaneously increased the conductivity and mechanical properties.The annealed treatment improved the thermal conductivity of these alloys due to the decreasing concentration of point defects.Rolling process further broke up the coarser Fe-containing phases into finer particles and made the secondary phases uniformly distributed in theα(Al)matrix.After subsequent annealing treatment and rolling deformation,the thermal conductivity,ultimate tensile strength and hardness of the Al−2%Fe−0.3%Ce(mass fraction)alloy reached 226 W/(m·K),(182±1.4)MPa and HBW(49.5±1.7),respectively.
基金the financial supports of the Ministry of Knowledge Economy (Republic of Korea) through Grant No. 10033429Inha University Research Grant
文摘Al-Si-Fe based alloys are attractive light-weight structural materials for automotive engine components because of their high wear resistance, low density and low thermal expansion. Al-17Si 5Fe-2Cu-lMg-lNi-lZr alloys were produced in compact form by a spark plasma sintering （SPS） technique using gas atomized powders. The mean grain size of the compact was 530 nm, and fine equiaxed grains and uniformly distributed precipitates were observed in the compact. The compressive deformation behavior of the SPSed materials was examined at various temperatures and strain rates. All the true stress-true strain curves showed steady state flow after reaching peak stress. The peak stress decreased with increasing test temperature and decreasing strain rate. In the deformed specimens, the equiaxed grain morphology and the dislocation microstructure within the equiaxed grains were observed. These facts strongly indicated the occurrence of dynamic recrystallization during high temperature deformation of the present alloy.
基金supported by the KMB project (193179/I40) in NorwayThe financial support by the Research Council of Norway and the industrialpartners, Hydro Aluminium and Sapa Technology
文摘Microstructural evolution of a cold-rolled Al-Mn-Fe-Si alloy during annealing was studied. Except the as-cast variant, two other different homogenizations were considered, one gave a high density of fine dispersiods providing a considerable Zener drag influencing the softening behavior while the other gave a lower density of coarser dispersoid structure providing a much smaller drag effect. The gradual microstructural evolutions during annealing for the three variants were captured by interrupting annealing at different time. Effects of microchemistry state on recrystallization kinetics, recrystallized grain structure and texture were characterized by EBSD. It is demonstrated that the actual softening kinetics, final microstructure and texture are a result of delicate balance between processing condition and microchemistry state. Strong concurrent precipitation takes place in the case with high concentration of Mn in solid solution, which suppresses nucleation and retards recrystallization and finally leads to grain structure of coarse elongated grains dominated by a P texture component together with a ND-rotated cube component. On the contrary, when solute content of Mn is low and pre-existing dispersoids are relatively coarser, faster recrystallization kinetics is exhibited together with an equiaxed grain structure with mainly cube texture.
基金funded by the National Plan for Science,Technology and Innovation(MAARIFAH)King Abdulaziz City for Science and Technology,Kingdom of Saudi Arabia,Award Number(12-NAN2635-02)
文摘Thermal stability of nanocrystalline Al-10wt.%Fe-5wt.%Cr bulk alloy was investigated.The initial micro-grained mixture of powders was processed for 100 h using mechanical alloying(MA)to produce nano-grained alloy.The processed powders were sintered using high frequency induction heat sintering(HFIHS).The microstructures of the processed alloy in the form of powders and bulk samples were investigated using XRD,FESEM and HRTEM.Microhardness and compression tests were conducted on the bulk samples for evaluating their mechanical properties.To evaluate the thermal stability of the bulk samples,they were experimented at 573,623,673 and 723 K under compression load at strain rates of 1×10^-1 and 1×10^-2 s^-1.The annealed samples exhibited a significant increase in their microhardness value of 2.65 GPa when being annealed at 723 K,as compared to 2.25 GPa of the as-sintered alloy.The bulk alloy revealed compressive strengths of 520 MPa and 450 MPa at 300 K and 723 K,respectively,when applying a strain rate of 1×10^-1 s^-1.The microstructural stability of the bulk alloy was ascribed to the formation of iron and chromium containing phases with Al such as Al6Fe,Al13Fe4 and Al13Cr2,in addition to the supersaturated solid solution(SSSS)of Cr and Fe in Al matrix.
基金Project(51574241)supported by the National Natural Science Foundation of ChinaProject(51611130064)supported by the Bilateral Project of NSFC-STINTProject(2015QN004)supported by the Program for Innovation Research Team of China University of Mining and Technology
文摘Porous FeAl-based intermetallics were fabricated by thermal explosion（TE） from Fe and Al powders. The effects of sintering temperature on phase constitution, pore structure and oxidation resistance of porous Fe-Al intermetallics were systematically investigated. Porous Fe-Al materials with high open porosity（65%） are synthesized via a low-energy consumption method of TE at a temperature of 636 ℃ and FeAl intermetallic is evolved as dominant phase in sintered materials at 1000 ℃. The porous materials are composed of interconnected skeleton, large pores among skeleton and small pores in the interior of skeleton. The interstitial pores in green powder compacts are the important source of large pores of porous Fe-Al intermetallics, and the in-situ pores from the melting and flowing of aluminum powders are also significant to the formation of large pores. Small pores are from the precipitation of Fe-Al intermetallics particles. In addition, the porous specimens exhibit high resistance to oxidation at 650 ℃ in air.
基金Foundation item:Project(51671045)supported by the National Natural Science Foundation of ChinaProject(DUT18GF112)supported by the Fundamental Research Funds for the Central Universities,ChinaProject(TZ2016004)supported by the Science Challenge Project,China
文摘The formation of nanoporous Pd was studied by electro-chemical dealloying a rapidly-quenched Al70Pd17Fe13 quasicrystal alloy in dilute NaCl aqueous solution,and the electro-catalytic activity of the nanoporous Pd towards methanol electro-oxidation was evaluated by cyclic voltammetry in 1 mol/L KOH solution.XRD and TEM analyses revealed that nano-decomposition of quasicrystal grains occurred in the initial stage of dealloying,and the fully dealloyed sample was composed of FCC-Pd phase.Scanning electron microscopy observation indicated that a maze-like nanoporous pattern was formed in the dealloyed sample,consisting of percolated pores of 5.20 nm in diameter in a skeleton of randomly-orientated Pd nano-ligaments with a uniform thickness of^5 nm.A retention of^12 at.%Al in the Pd nano-ligments was determined by energy dispersive X-ray spectroscopy(EDS).The nanoporous Pd demonstrated obvious electro-catalytic activity towards methanol electro-oxidation in alkaline environment.
基金The authors are grateful for the financial supports from the National Natural Science Foundation of China(51771035,51671037)Natural Science Foundation of Jiangsu Province,China(BK20161190)the Priority Academic Program of Jiangsu Higher Education Institutions,China.
文摘The effects of Fe content on the microstructure,phase constituents and microhardness of the as-cast,800℃or 1000℃-annealed Al_(7)Cr_(20)Fe_(x)Ni_(73)−x(x=13−66)alloys were investigated.Not all these alloys are composed of the single FCC phase.The BCC and B2 phases are found.It is confirmed that the BCC phase in the Al7Cr20Fe66Ni7 alloy is transformed from the FCC phase at about 900℃ during cooling.While in the 800℃-annealed Al7Cr20Fe60Ni13 alloy,the FCC phase is stable and the hardness decreases.After annealing at 1000℃,for the precipitation of the B2 particles,the Al content in the FCC phase decreases,which results in decreasing of the alloy hardness.Moreover,after annealing at 800℃,a small amount of Al-rich B2 particles precipitate at the phase boundary and some nanocrystal BCC phase precipitates in the FCC matrix,which increases the hardness of the Al_(7)Cr_(20)Fe_(x)Ni_(73)−x(x=41−49)alloys.These results will help to the composition design and processing design of the Al−Cr−Fe−Ni based high-entropy alloys.
文摘The effect of iron addition on the microstructure, mechanical and magnetic properties of Al-matrix composite was studied. Mechanical mixing was used for the preparation of 0, 5%, 10% and 15% Fe-Al composites（mass fraction）. Mixtures of Al-Fe were compacted and sintered in a vacuum furnace at 600 °C for 1 h. X-ray diffraction（XRD） of the samples containing 5% and 10% Fe indicates the presence of Al and Fe peaks, while sample containing 15% Fe reveals Al and Al13Fe4 peaks. The results show that both densification and thermal conductivity of the composites decrease by increasing the iron content. The presence of iron in the composite improves the compressive strength and the hardness. The strengthening mechanism is associated with the grain refinement of the matrix and uniform distribution of the Fe particles, as well as the formation of Al13Fe4 intermetallic. The measured magnetization values are equal to 0.3816×10-3 A·m2/g for 5% Fe sample and increases up to 0.6597×10-3 A·m2/g for 10% Fe sample, then decreases to 0.0702×10-3 A·m2/g for 15% Fe sample. This can be explained by the formation of the diamagnetic Al13Fe4 intermetallic compound in the higher Fe content sample detected by XRD analysis.
基金Project(97.13966(97.11.15)) supported by the Deputy of Research and Technology of Arak University,Iran。
文摘Commercial pure aluminum and galvanized carbon steel were lap-welded using the weld-brazing(WB)technique.Three types of aluminum filler materials(4043,4047,and 5356) were used for WB.The joint strength and intermetallic compounds at the interface of three series of samples were analyzed and compared.Depending on the Si content,a variety of ternary Al-Fe-Si intermetallic compounds(IMCs) such as Fe_(4)(Al,Si)_(13),Fe_(2) Al_(8) Si(τ_(5)),and Fe_(2) Al_(9) Si_(2)(τ_(6)) were formed at the interface.Mg element in 5356 filler material cannot contribute to the formation of Al-Fe intermetallic phases due to the positive mixing enthalpy of Mg-Fe.The presence of Mg enhances the hot cracking phenomenon near the Al-Fe intermetallic compound at the interface.Zn coating does not participate in intermetallic formation due to its evaporation during WB.It was concluded that the softening of the base metal in the heat-affected zone rather than the IMCs determines the joint efficiency.
文摘The effect of incorporating limited-diffusivity elements such as Fe and Ti on thermal stability of the nanocrystalline Al alloy was investigated.Al−10wt.%Fe and Al−10wt.%Fe−5wt.%Ti alloys were fabricated.The initial mixtures of powders were milled for 100 h in vacuum.The bulk samples were fabricated from the milled powders in a high frequency induction heat sintering(HFIHS)system.The milled powders and the bulk sintered samples were characterized by X-ray diffraction(XRD),Vickers microhardness,field emission scanning electron microscopy(FESEM-EDS)and transmission electron microscopy(TEM).The observations indicated that Fe and Ti were completely dispersed in the matrix to form a supersaturated solid solution(SSSS)with Al.Additionally,the inclusion of alloying elements led to an increase in hardness and yield strength of the alloy by 127%and 152%,respectively.The elevated temperature compression tests were carried out to evaluate the thermal stability of the alloys.The Al−10wt.%Fe−5wt.%Ti alloy revealed the optimum thermally stable behavior of the three alloys studied.The incorporation of Fe and Ti improved the thermal stability of the developed alloys through inhibiting the grain growth,hindering dissolution and growth of second phases(such as Al13Fe4 and Al13Ti),and forming a stable solid solution.
文摘An experimental study has been carried out to investigate the influence of heat treatment at 300 ℃,450 ℃,550 ℃,650 ℃ and 800 ℃ on the microstructure and sliding wear behavior of Fe Al/WC intermetallic composite coatings produced by high velocity arc spraying (HVAS) and cored wires. The result shows, the main phases in both as sprayed and heat treated Fe Al/WC composite coatings are iron aluminide intermetallics (Fe 3Al+FeAl) and α as well as a little oxide (Al 2O 3) and carbides (WC, W 2C, Fe 2W 2C and Fe 6W 6C). After heat treated at 450-650 ℃, dispersion strengthening of Fe 2W 2C and Fe 6W 6C will lead to a rise in microhardness of the coatings. The microhardness is likely to be the most important factor which influences the sliding wear behavior of the coatings. Increasing the microhardness through heat treatment will improve the sliding wear resistance of the Fe Al/WC composite coatings.
