Finite element analysis has been carried out to understand the effect of various processing routes and condition on the microscale deformation behavior of Al–4.5 Cu–2 Mg alloy. The alloy has been developed through f...Finite element analysis has been carried out to understand the effect of various processing routes and condition on the microscale deformation behavior of Al–4.5 Cu–2 Mg alloy. The alloy has been developed through four different routes and condition, i.e. conventional gravity casting with and without refiner, rheocasting and SIMA process. The optical microstructures of the alloy have been used to develop representative volume elements（RVEs）. Two different boundary conditions have been employed to simulate the deformation behavior of the alloy under uniaxial loading. Finally, the simulated stress-strain behavior of the alloy is compared with the experimental result. It is found that the microstructural morphology has a significant impact on stress and strain distribution and load carrying capacity. The eutectic phase always carries a higher load than the α（Al） phase. The globular α（Al） grains with thinner and uniformly distributed eutectic network provide a better stress and strain distribution. Owing to this, SIMA processed alloy has better stress and strain distribution than other processes. Finally, the simulated yield strength of the alloy is verified by experiment and they have great agreement.展开更多
Direct reaction synthesis (DRS), based on the principle of self-propagating high-temperature synthesis (SHS), is a new method for preparing participate metal matrix composites. TiCP/AI-4.5Cu-0.8Mg composites were fabr...Direct reaction synthesis (DRS), based on the principle of self-propagating high-temperature synthesis (SHS), is a new method for preparing participate metal matrix composites. TiCP/AI-4.5Cu-0.8Mg composites were fabricated by DRS. Participate composites were fabricated with Ti carbide (TiC) particles, generally less than 1.0μm. The reacted, thermal extruded samples exhibit a homogeneous distribution of fine TiC particles in AI-4.5Cu-0.8Mg matrix. Mechanical property evaluation of the composites has revealed a very high tensile strength relative to the matrix alloy. Fractographic analysis indicates ductile failure.展开更多
The objective of the current study was to investigate the use of ultrasonic melt treatment technology in the production of grain-refined billets of the AC7 A alloy, which was intended for subsequent use as a feedstock...The objective of the current study was to investigate the use of ultrasonic melt treatment technology in the production of grain-refined billets of the AC7 A alloy, which was intended for subsequent use as a feedstock in forming operations. The experiments included the application of ultrasonic vibrations to the molten alloys via direct and indirect techniques. Several process parameters such as pouring temperatures(several temperatures between 740 and 660℃), and treatment time(from 12 min down to 2 min) were investigated. The experiment included continuous ultrasonic treatment from the liquid to the semisolid states. The results showed that both treatment techniques were viable for producing billets with the desirable microstructural characteristics. The optimum treatment conditions were the short treatment time(2 to 3 min), from about 660℃ down to 615℃ for the indirect treatment technique, and from 660℃ to 635℃ for the direct treatment technique. The resulting microstructures, at three positions along the height of the ingot, were characterized by fine, non-dendritic α(Al) grains in the order of a hundred microns, as compared to few thousands of microns for the conventional cast ingots. The intermetallic particles were also refined in size and modified in morphology by the ultrasonic treatment. The operating mechanisms by which the ultrasonic vibrations altered the ingot microstructures were discussed and analyzed.展开更多
文摘Finite element analysis has been carried out to understand the effect of various processing routes and condition on the microscale deformation behavior of Al–4.5 Cu–2 Mg alloy. The alloy has been developed through four different routes and condition, i.e. conventional gravity casting with and without refiner, rheocasting and SIMA process. The optical microstructures of the alloy have been used to develop representative volume elements（RVEs）. Two different boundary conditions have been employed to simulate the deformation behavior of the alloy under uniaxial loading. Finally, the simulated stress-strain behavior of the alloy is compared with the experimental result. It is found that the microstructural morphology has a significant impact on stress and strain distribution and load carrying capacity. The eutectic phase always carries a higher load than the α（Al） phase. The globular α（Al） grains with thinner and uniformly distributed eutectic network provide a better stress and strain distribution. Owing to this, SIMA processed alloy has better stress and strain distribution than other processes. Finally, the simulated yield strength of the alloy is verified by experiment and they have great agreement.
文摘Direct reaction synthesis (DRS), based on the principle of self-propagating high-temperature synthesis (SHS), is a new method for preparing participate metal matrix composites. TiCP/AI-4.5Cu-0.8Mg composites were fabricated by DRS. Participate composites were fabricated with Ti carbide (TiC) particles, generally less than 1.0μm. The reacted, thermal extruded samples exhibit a homogeneous distribution of fine TiC particles in AI-4.5Cu-0.8Mg matrix. Mechanical property evaluation of the composites has revealed a very high tensile strength relative to the matrix alloy. Fractographic analysis indicates ductile failure.
文摘The objective of the current study was to investigate the use of ultrasonic melt treatment technology in the production of grain-refined billets of the AC7 A alloy, which was intended for subsequent use as a feedstock in forming operations. The experiments included the application of ultrasonic vibrations to the molten alloys via direct and indirect techniques. Several process parameters such as pouring temperatures(several temperatures between 740 and 660℃), and treatment time(from 12 min down to 2 min) were investigated. The experiment included continuous ultrasonic treatment from the liquid to the semisolid states. The results showed that both treatment techniques were viable for producing billets with the desirable microstructural characteristics. The optimum treatment conditions were the short treatment time(2 to 3 min), from about 660℃ down to 615℃ for the indirect treatment technique, and from 660℃ to 635℃ for the direct treatment technique. The resulting microstructures, at three positions along the height of the ingot, were characterized by fine, non-dendritic α(Al) grains in the order of a hundred microns, as compared to few thousands of microns for the conventional cast ingots. The intermetallic particles were also refined in size and modified in morphology by the ultrasonic treatment. The operating mechanisms by which the ultrasonic vibrations altered the ingot microstructures were discussed and analyzed.
