The 430 ℃ isothermal section of the Al 4Mg Sc Zr quaternary system in the Al rich range was determined by means of equilibrium alloys with the use of microstructure, X ray diffraction analysis and electron probe micr...The 430 ℃ isothermal section of the Al 4Mg Sc Zr quaternary system in the Al rich range was determined by means of equilibrium alloys with the use of microstructure, X ray diffraction analysis and electron probe microanalysis. There coexist three single phase fields, two two phase fields and one three phase field. It is established that the phase Al 3Sc 10.5 Zr 00.5 with L1 2 structure and Al 3Zr 10.8 Sc 00.2 with DO 23 structure are in equilibrium with the α solid solution, Zr being dissolved in Al 3Sc, further substituting for about 50% Sc(mole fraction) whilst Sc is present in the phase Al 3Zr and the maximum substitution for Zr is about 20%.展开更多
Binary Al-4Mg alloy have been deformed by hot torsion at 300-500 deg C andstrain rates of 0.006-1.587 s^(-1) to a true strain of 5.5. The specimens were annealed in vacuumfor 1.5 h at 500 deg C and then water quenched...Binary Al-4Mg alloy have been deformed by hot torsion at 300-500 deg C andstrain rates of 0.006-1.587 s^(-1) to a true strain of 5.5. The specimens were annealed in vacuumfor 1.5 h at 500 deg C and then water quenched. The study indicates that the dynamicrecrystallization occurs during hot torsion of Al-4Mg alloy in a certain range of Z parameter(Zener-Hollmon Parameter), i.e. 19.3 <= lnZ <=24.8. Increasing the strain rate at higher deformationtemperature or reducing the strain rate at lower deformation temperature accelerates the occurrenceof dynamic recrystallization in the alloy.展开更多
The microstructural evolution and mechanical properties of Al-18 Si-4 Cu-0.5 Mg alloy modified by the addition of La-Ce rare earth elements through OM,SEM,EPMA and tensile tests were investigated.The results of OM and...The microstructural evolution and mechanical properties of Al-18 Si-4 Cu-0.5 Mg alloy modified by the addition of La-Ce rare earth elements through OM,SEM,EPMA and tensile tests were investigated.The results of OM and SEM analyses indicated that primary Si particles were significantly refined from coarse block-like and irregular polygonal shapes into fine flaky shapes,while eutectic Si particles were modified from coarse and needle-like into fine and rod-or coral-like shapes with increase of La-Ce addition.The alloy exhibited the minimum primary Si particle size and the best mechanical properties with the addition of 0.3 wt.%La-Ce.The average particle size decreased from 61 to 28 μm,the ultimate tensile strength increased from 222 to 242 MPa and the elongation increased from 3.2% to 6.3%.In addition,modification mechanisms and fracture modes were explored by the means of SEM and EPMA.展开更多
文摘The 430 ℃ isothermal section of the Al 4Mg Sc Zr quaternary system in the Al rich range was determined by means of equilibrium alloys with the use of microstructure, X ray diffraction analysis and electron probe microanalysis. There coexist three single phase fields, two two phase fields and one three phase field. It is established that the phase Al 3Sc 10.5 Zr 00.5 with L1 2 structure and Al 3Zr 10.8 Sc 00.2 with DO 23 structure are in equilibrium with the α solid solution, Zr being dissolved in Al 3Sc, further substituting for about 50% Sc(mole fraction) whilst Sc is present in the phase Al 3Zr and the maximum substitution for Zr is about 20%.
基金The project was sponsored by the Education Administration Major Project for Science Research under the contract No. 99134.
文摘Binary Al-4Mg alloy have been deformed by hot torsion at 300-500 deg C andstrain rates of 0.006-1.587 s^(-1) to a true strain of 5.5. The specimens were annealed in vacuumfor 1.5 h at 500 deg C and then water quenched. The study indicates that the dynamicrecrystallization occurs during hot torsion of Al-4Mg alloy in a certain range of Z parameter(Zener-Hollmon Parameter), i.e. 19.3 <= lnZ <=24.8. Increasing the strain rate at higher deformationtemperature or reducing the strain rate at lower deformation temperature accelerates the occurrenceof dynamic recrystallization in the alloy.
基金Project(51274245) supported by the National Natural Science Foundation of China
文摘The microstructural evolution and mechanical properties of Al-18 Si-4 Cu-0.5 Mg alloy modified by the addition of La-Ce rare earth elements through OM,SEM,EPMA and tensile tests were investigated.The results of OM and SEM analyses indicated that primary Si particles were significantly refined from coarse block-like and irregular polygonal shapes into fine flaky shapes,while eutectic Si particles were modified from coarse and needle-like into fine and rod-or coral-like shapes with increase of La-Ce addition.The alloy exhibited the minimum primary Si particle size and the best mechanical properties with the addition of 0.3 wt.%La-Ce.The average particle size decreased from 61 to 28 μm,the ultimate tensile strength increased from 222 to 242 MPa and the elongation increased from 3.2% to 6.3%.In addition,modification mechanisms and fracture modes were explored by the means of SEM and EPMA.
