Effects of （Pr＋Ce） addition on the Al-7Si-0.7Mg alloy were investigated by optical microscope （OM）, energy diffraction spectrum （EDS）, X-ray diffraction （XRD） and tensile tests. The results showed that the Al...Effects of （Pr＋Ce） addition on the Al-7Si-0.7Mg alloy were investigated by optical microscope （OM）, energy diffraction spectrum （EDS）, X-ray diffraction （XRD） and tensile tests. The results showed that the Al-7Si-0.7Mg alloy was modified with （Pr＋Ce） addition. The needle-like eutectic silicon phase developed into rose form and the crystalline grains decreased in size and showed a high degree of spheroidization. When the amount of the （Pr＋Ce） addition reached 0.6 wt.%, the mean diameter was 31.8μm （refined by 50%）. The aspect ratio decreased to 1.35, and the tensile strength and ductility reached 192.4 MPa and 2.18%, respectively At higher levels of addition, over-modification occurred, as indicated by increased grain size and reduced mechanical properties. The poisoning effect of the （Pr＋Ce） addition on eutectic silicon and the constitutional supercooling caused by the （Pr＋Ce） addition were the major causes of alloy modification, grain refinement, and the improvement of mechanical properties.展开更多
The effects of Si content on the microstructure and yield strength of Al-(1.44-12.40)Si-0.7 Mg(wt.%)alloy sheets under the T4 condition were systematically studied via laser scanning confocal microscopy(LSCM),DSC,TEM ...The effects of Si content on the microstructure and yield strength of Al-(1.44-12.40)Si-0.7 Mg(wt.%)alloy sheets under the T4 condition were systematically studied via laser scanning confocal microscopy(LSCM),DSC,TEM and tensile tests.The results show that the recrystallization grain of the alloy sheets becomes more refined with an increase in Si content.When the Si content increases from 1.44 to 12.4 wt.%,the grain size of the alloy sheets decreases from approximately 47 to 10μm.Further,with an increase in Si content,the volume fraction of the GP zones in the matrix increases slightly.Based on the existing model,a yield strength model for alloy sheets was proposed.The predicted results are in good agreement with the actual experimental results and reveal the strengthening mechanisms of the Al-(1.44-12.40)Si-0.7 Mg alloy sheets under the T4 condition and how they are influenced by the Si content.展开更多
基金financially supported by the Fundamental Research Funds for the Central Universities,China(No.2020CDJDPT001)the Chongqing Natural Science Foundation,China(No.cstc2021jcyj-msxm X0699)。
基金Project supported by the National Natural Science Foundation of China(51364035)Ministry of Education tied up with the Special Research Fund for the Doctoral Program for Higher School(20133601110001)+1 种基金Loading Program of Science and Technology of College of Jiangxi Province(KJLD14003)Open Project Program of Jiangxi Engineering Research Center of Process and Equipment for New Energy,East China Institute of Technology(JXNE2015-09)
文摘Effects of （Pr＋Ce） addition on the Al-7Si-0.7Mg alloy were investigated by optical microscope （OM）, energy diffraction spectrum （EDS）, X-ray diffraction （XRD） and tensile tests. The results showed that the Al-7Si-0.7Mg alloy was modified with （Pr＋Ce） addition. The needle-like eutectic silicon phase developed into rose form and the crystalline grains decreased in size and showed a high degree of spheroidization. When the amount of the （Pr＋Ce） addition reached 0.6 wt.%, the mean diameter was 31.8μm （refined by 50%）. The aspect ratio decreased to 1.35, and the tensile strength and ductility reached 192.4 MPa and 2.18%, respectively At higher levels of addition, over-modification occurred, as indicated by increased grain size and reduced mechanical properties. The poisoning effect of the （Pr＋Ce） addition on eutectic silicon and the constitutional supercooling caused by the （Pr＋Ce） addition were the major causes of alloy modification, grain refinement, and the improvement of mechanical properties.
基金Project(2016YFB0300801)supported by the National Key Research and Development Program of ChinaProject(51871043)supported by the National Natural Science Foundation of ChinaProject(N180212010)supported by the Fundamental Research Funds for the Central Universities of China。
文摘The effects of Si content on the microstructure and yield strength of Al-(1.44-12.40)Si-0.7 Mg(wt.%)alloy sheets under the T4 condition were systematically studied via laser scanning confocal microscopy(LSCM),DSC,TEM and tensile tests.The results show that the recrystallization grain of the alloy sheets becomes more refined with an increase in Si content.When the Si content increases from 1.44 to 12.4 wt.%,the grain size of the alloy sheets decreases from approximately 47 to 10μm.Further,with an increase in Si content,the volume fraction of the GP zones in the matrix increases slightly.Based on the existing model,a yield strength model for alloy sheets was proposed.The predicted results are in good agreement with the actual experimental results and reveal the strengthening mechanisms of the Al-(1.44-12.40)Si-0.7 Mg alloy sheets under the T4 condition and how they are influenced by the Si content.
