期刊文献+
共找到174,258篇文章
< 1 2 250 >
每页显示 20 50 100
不同形貌Al-Fe金属的块体压制成形模拟研究
1
作者 李振亮 王鑫 《制造技术与机床》 北大核心 2024年第4期71-77,共7页
文章以含40%Al的Al-Fe复合金属为研究对象,对颗粒状和屑状40Al-Fe复合金属分别进行压制预变形,并对屑状40Al-Fe复合金属预制坯进行了二次热压缩变形,重点研究压制预变形及二次热压缩对Al-Fe复合金属成形性和界面影响。结果表明:压力为16... 文章以含40%Al的Al-Fe复合金属为研究对象,对颗粒状和屑状40Al-Fe复合金属分别进行压制预变形,并对屑状40Al-Fe复合金属预制坯进行了二次热压缩变形,重点研究压制预变形及二次热压缩对Al-Fe复合金属成形性和界面影响。结果表明:压力为16 MPa时,颗粒状40Al-Fe复合金属预制坯(密度为4.54 g/cm^(3))成形性良好且形成致密界面;压力为16 MPa时,屑状40Al-Fe复合金属预制坯(密度为3.50 g/cm3)可以成形但界面存在孔洞,Al屑主要为“片层状”“狗牙状”“圆圈状”“波浪状”,其经二次热压缩变形,“圆圈状”Al屑连成一个整体,“狗牙状”与“波浪状”Al屑均演变为“片层状”,而Fe屑仍为“片层状”“块状”,未发生明显变形。变形温度300℃、变形速率0.5 s^(-1)、变形程度0.1是目前生产工艺最佳参数,此时屑状40Al-Fe复合金属成形性最佳且界面结合良好(密度为4.66 g/cm^(3))。 展开更多
关键词 压制成形 al-fe复合金属 界面
下载PDF
锑元素对Al-Fe合金的力学性能及耐蚀性的影响
2
作者 陈国桢 郭辉 《轻合金加工技术》 CAS 2024年第8期22-27,共6页
锂离子电池铝塑膜用铝箔需要有较高的成形性及耐蚀性。通过场发射扫描电镜、万能拉伸试验机、电化学工作站等设备对不同Sb含量的Al-1.45Fe合金的力学性能及耐蚀性进行研究。研究结果表明:在Al-1.45Fe合金中添加适量的Sb,合金的伸长率升... 锂离子电池铝塑膜用铝箔需要有较高的成形性及耐蚀性。通过场发射扫描电镜、万能拉伸试验机、电化学工作站等设备对不同Sb含量的Al-1.45Fe合金的力学性能及耐蚀性进行研究。研究结果表明:在Al-1.45Fe合金中添加适量的Sb,合金的伸长率升高;添加过量的Sb,合金的伸长率降低;当添加w(Sb)=0.05%时,合金的伸长率可以达到27.4%,与未添加Sb的合金的伸长率19.5%相比,提升了40.5%。极化曲线表明,添加Sb后,合金的自腐蚀电位升高,自腐蚀电流降低,耐蚀性得到提升。 展开更多
关键词 铝箔 al-fe合金 伸长率 耐蚀性
下载PDF
半固态连续成形Al-Fe合金的工艺参数优化及组织性能分析
3
作者 张雪飞 张越 +2 位作者 张发 张弛 杜宝怡 《沈阳大学学报(自然科学版)》 CAS 2023年第4期273-278,共6页
针对Al-Fe合金半固态连续成形工艺中挤压轮转速、挤压温度、Fe元素质量分数等参数进行优化。结果表明:当挤压轮转速为10 r·min-1、挤压温度为690℃、合金中Fe元素质量分数为1.00%时,可获得较好的Al-Fe合金线材质量。采用扫描电镜(S... 针对Al-Fe合金半固态连续成形工艺中挤压轮转速、挤压温度、Fe元素质量分数等参数进行优化。结果表明:当挤压轮转速为10 r·min-1、挤压温度为690℃、合金中Fe元素质量分数为1.00%时,可获得较好的Al-Fe合金线材质量。采用扫描电镜(SEM)、扫描电镜能谱分析(EDS)及透射电镜(TEM)对半固态连续成形最优工艺条件下制备的Al-Fe合金进行微观组织分析,确定了第二相成分,并分析了半固态连续成形工艺对含铁相的细化作用。经拉伸力学性能测试,Al-Fe合金线材屈服强度为85 MPa、抗拉强度为142 MPa、延伸率为35%;SEM测试表明拉伸断口形貌为韧性断裂。 展开更多
关键词 al-fe合金 半固态连续成形 工艺参数优化 有限元数值模拟 微观组织形貌
下载PDF
Three-dimensional modeling of effect of surface intermetallic phase on surface defects of Al-Fe-Si aluminum foils during twin-roll casting
4
作者 朱远志 万强 +2 位作者 李丙亮 周峰 张雅峰 《Transactions of Nonferrous Metals Society of China》 SCIE EI CAS CSCD 2014年第2期477-483,共7页
Scanning electron microscopy and X-ray energy dispersive spectrum analysis show that the clusters of intermetallic AlFeSi particle are distributed on or near the aluminum foil stock surfaces heterogeneously. 3D finite... Scanning electron microscopy and X-ray energy dispersive spectrum analysis show that the clusters of intermetallic AlFeSi particle are distributed on or near the aluminum foil stock surfaces heterogeneously. 3D finite element modeling shows that these clusters of hard particles induce the fracture of the nano-scale lubricant oil film at first and further lead to severe deformation in the nearby aluminum foil substrate along the rolling direction. Consequently, the optical property in this region differs from that in the surroundings, resulting in surface defects. 展开更多
关键词 al-fe-Si alloy precipitated phase aluminum foils lubricant oil film twin-roll cast 3D modeling
下载PDF
基于CTA颅内动脉瘤形态联合PHASES评分对破裂出血预测研究
5
作者 王金泉 黄吉淮 谢颖 《影像研究与医学应用》 2024年第4期31-34,共4页
目的:分析头颈部计算机断层扫描血管成像(CTA)联合PHASES评分对颅内动脉瘤(IA)破裂出血的预测价值。方法:回顾性分析2021年10月—2023年9月东莞市长安医院诊治的IA患者临床资料,根据IA破裂出血与否分为IA破裂组(n=46)和IA未破裂组(n=44)... 目的:分析头颈部计算机断层扫描血管成像(CTA)联合PHASES评分对颅内动脉瘤(IA)破裂出血的预测价值。方法:回顾性分析2021年10月—2023年9月东莞市长安医院诊治的IA患者临床资料,根据IA破裂出血与否分为IA破裂组(n=46)和IA未破裂组(n=44),收集两组临床资料,对比两组患者CTA影像瘤体特征参数和PHASES评分结果。采用受试者工作特征(ROC)曲线分析两者联合预测动脉瘤破裂的效能。结果:IA破裂组高血压、糖尿病发生率及PHASES评分均高于IA未破裂组,差异有统计学意义(P <0.05)。两组病灶位置以颈内动脉(ICA)和大脑中动脉(MCA)为主,但IA破裂组病灶位置在MCA的占比为41.30%,高于IA未破裂组的20.45%,瘤体>7 mm的最多(瘤体7~9.9 mm占65.22%),瘤体形态不规则占58.7%,未破裂组病灶位置在ICA最多(68.18%),瘤体<7 mm的居多(75.00%),瘤体形态规则囊状动脉瘤占93.18%,差异有统计学意义(P <0.05)。CTA瘤体特征参数比较,IA破裂组患者瘤颈宽度、瘤体高度、瘤体长度、动脉瘤最大直径、入射夹角、动脉瘤体颈比等参数均高于IA未破裂组,差异有统计学意义(P <0.05)。CTA瘤体特征参数+PHASES评分联合预测曲线下面积为0.916,高于CTA瘤体特征参数(0.901)和PHASES评分(0.731)。结论:CTA瘤体特征参数+PHASES评分联合预测IA患者破裂出血效能最佳。 展开更多
关键词 颅内动脉瘤 破裂出血 CTA phaseS评分
下载PDF
FORMATION OF QUASICRYSTALLINE PHASE IN RAPIDLY SOLIDIFIED Al-Fe-V-Si ALLOY 被引量:1
6
作者 GUAN Shaokang, TANG Yali, SHEN Ningfu, ZHAO DongshanZhengzhou Institute of Technology. Zhengzhou. ChinaHU HanqiUniversity of Science and Technology Beijing. Beijing, China 《Acta Metallurgica Sinica(English Letters)》 SCIE EI CAS CSCD 1994年第3期167-170,共4页
The icosahedral quasicrvstalline phase (i-phase) with the chemical composition of 82.4at%Al. 8.8at%Fe. 3.6at%V and 5.2at%Si in melt spun Al-Fe-V-Si ribbons was found. It is suggested that the temperature and holding t... The icosahedral quasicrvstalline phase (i-phase) with the chemical composition of 82.4at%Al. 8.8at%Fe. 3.6at%V and 5.2at%Si in melt spun Al-Fe-V-Si ribbons was found. It is suggested that the temperature and holding time of the melt prior to quenching are the important factors in the formation of the i-phase. 展开更多
关键词 quasicrvstalline phase al-fe-V-Si alloy rapid solidification
下载PDF
Phase-engineering modulation of Mn-based oxide cathode for constructing super-stable sodium storage 被引量:1
7
作者 Quanqing Zhao Ruru Wang +5 位作者 Ming Gao Bolin Liu Jianfeng Jia Haishun Wu Youqi Zhu Chuanbao Cao 《Journal of Energy Chemistry》 SCIE EI CAS CSCD 2024年第1期421-427,I0010,共8页
The Mn-based oxide cathode with enriched crystal phase structure and component diversity can provide the excellent chemistry structure for Na-ion batteries.Nevertheless,the broad application prospect is obstructed by ... The Mn-based oxide cathode with enriched crystal phase structure and component diversity can provide the excellent chemistry structure for Na-ion batteries.Nevertheless,the broad application prospect is obstructed by the sluggish Na^(+)kinetics and the phase transitions upon cycling.Herein,we establish the thermodynamically stable phase diagram of various Mn-based oxide composites precisely controlled by sodium content tailoring strategy coupling with co-doping and solid-state reaction.The chemical environment of the P2/P'3 and P2/P3 biphasic composites indicate that the charge compensation mechanism stems from the cooperative contribution of anions and cations.Benefiting from the no phase transition to scavenge the structure strain,P2/P'3 electrode can deliver long cycling stability(capacity retention of 73.8%after 1000 cycles at 10 C)and outstanding rate properties(the discharge capacity of 84.08 mA h g^(-1)at 20 C)than P2/P3 electrode.Furthermore,the DFT calculation demonstrates that the introducing novel P'3 phase can significantly regulate the Na^(+)reaction dynamics and modify the local electron configuration of Mn.The effective phase engineering can provide a reference for designing other high-performance electrode materials for Na-ion batteries. 展开更多
关键词 Sodium ion battery Oxide cathode phase engineering phase diagram Na~+kinetic
下载PDF
Recent advances in graphene-based phase change composites for thermal energy storage and management 被引量:2
8
作者 Qiang Zhu Pin Jin Ong +4 位作者 Si Hui Angela Goh Reuben J.Yeo Suxi Wang Zhiyuan Liu Xian Jun Loh 《Nano Materials Science》 EI CAS CSCD 2024年第2期115-138,共24页
Energy storage and conservation are receiving increased attention due to rising global energy demands.Therefore,the development of energy storage materials is crucial.Thermal energy storage(TES)systems based on phase ... Energy storage and conservation are receiving increased attention due to rising global energy demands.Therefore,the development of energy storage materials is crucial.Thermal energy storage(TES)systems based on phase change materials(PCMs)have increased in prominence over the past two decades,not only because of their outstanding heat storage capacities but also their superior thermal energy regulation capability.However,issues such as leakage and low thermal conductivity limit their applicability in a variety of settings.Carbon-based materials such as graphene and its derivatives can be utilized to surmount these obstacles.This study examines the recent advancements in graphene-based phase change composites(PCCs),where graphene-based nanostructures such as graphene,graphene oxide(GO),functionalized graphene/GO,and graphene aerogel(GA)are incorporated into PCMs to substantially enhance their shape stability and thermal conductivity that could be translated to better storage capacity,durability,and temperature response,thus boosting their attractiveness for TES systems.In addition,the applications of these graphene-based PCCs in various TES disciplines,such as energy conservation in buildings,solar utilization,and battery thermal management,are discussed and summarized. 展开更多
关键词 phase change material NANOCOMPOSITES Solar energy Sustainable energy Thermo-regulation
下载PDF
Phase separation and transcriptional regulation in cancer development 被引量:1
9
作者 Yan Gu Ke Wei Jun Wang 《Journal of Biomedical Research》 CAS CSCD 2024年第4期307-321,共15页
Liquid-liquid phase separation,a novel biochemical phenomenon,has been increasingly studied for its medical applications.It underlies the formation of membrane-less organelles and is involved in many cellular and biol... Liquid-liquid phase separation,a novel biochemical phenomenon,has been increasingly studied for its medical applications.It underlies the formation of membrane-less organelles and is involved in many cellular and biological processes.During transcriptional regulation,dynamic condensates are formed through interactions between transcriptional elements,such as transcription factors,coactivators,and mediators.Cancer is a disease characterized by uncontrolled cell proliferation,but the precise mechanisms underlying tumorigenesis often remain to be elucidated.Emerging evidence has linked abnormal transcriptional condensates to several diseases,especially cancer,implying that phase separation plays an important role in tumorigenesis.Condensates formed by phase separation may have an effect on gene transcription in tumors.In the present review,we focus on the correlation between phase separation and transcriptional regulation,as well as how this phenomenon contributes to cancer development. 展开更多
关键词 phase separation transcription regulation CANCER super-enhancer CONDENSATES
下载PDF
Shikimic acid accelerates phase change and flowering in Chinese jujube 被引量:1
10
作者 Xianwei Meng Zhiguo Liu +11 位作者 Li Dai Weiqiang Zhao Jiurui Wang Lili Wang Yuanpei Cui Ying Li Yinshan Cui Yao Zhang Luyao Wang Fengjiao Yu Jin Zhao Mengjun Liu 《Horticultural Plant Journal》 SCIE CAS CSCD 2024年第2期413-424,共12页
The juvenile-to-adult phase change with first flowering as the indicator plays a crucial role in the lifecycle of fruit trees. However, the molecular mechanisms underlying phase change in fruit trees remain largely un... The juvenile-to-adult phase change with first flowering as the indicator plays a crucial role in the lifecycle of fruit trees. However, the molecular mechanisms underlying phase change in fruit trees remain largely unknown. Shikimic acid (ShA) pathway is a main metabolic pathway closely related to the synthesis of hormones and many important secondary metabolites participating in plant phase change. So,whether ShA regulates phase change in plants is worth clarifying. Here, the distinct morphological characteristics and the underlying mechanisms of phase change in jujube (Ziziphus jujuba Mill.), an important fruit tree native to China with nutritious fruit and outstanding tolerance abiotic stresses, were clarified. A combined transcriptome and metabolome analysis found that ShA is positively involved in jujube(Yuhong’×Xing 16’) phase change. The genes in the upstream of ShA synthesis pathway (ZjDAHPS, ZjDHQS and ZjSDH), the contents of ShA and the downstream secondary metabolites like phenols were significantly upregulated in the phase change period. Further, the treatment of spraying exogenous ShA verified that ShA at a very low concentration (60 mg·L^(-1)) can substantially speed up the phase change and flowering of jujube and other tested plants including Arabidopsis, tomato and wheat. The exogenous ShA (60 mg·L^(-1)) treatment in jujube seedlings could increase the accumulation of endogenous ShA, enhance leaf photosynthesis and the synthesis of phenols especially flavonoids and phenolic acids, and promote the expression of genes (ZjCOs, ZjNFYs and ZjPHYs) involved in flowering pathway. Basing on above results, we put forward a propose for the underlying mechanism of ShA regulating phase change, and a hypothesis that ShA could be considered a phytohormone-like substance because it is endogenous, ubiquitous, movable and highly efficient at very low concentrations. This study highlights the critical role of ShA in plant phase change and its phytohormone-like properties. 展开更多
关键词 Ziziphus jujuba Mill. phase change FLOWERING Shikimic acid TRANSCRIPTOME METABOLOME
下载PDF
Self‑Assembly of Binderless MXene Aerogel for Multiple‑Scenario and Responsive Phase Change Composites with Ultrahigh Thermal Energy Storage Density and Exceptional Electromagnetic Interference Shielding 被引量:1
11
作者 Chuanbiao Zhu Yurong Hao +8 位作者 Hao Wu Mengni Chen Bingqing Quan Shuang Liu Xinpeng Hu Shilong Liu Qinghong Ji Xiang Lu Jinping Qu 《Nano-Micro Letters》 SCIE EI CSCD 2024年第3期367-382,共16页
The severe dependence of traditional phase change materials(PCMs)on the temperature-response and lattice deficiencies in versatility cannot satisfy demand for using such materials in complex application scenarios.Here... The severe dependence of traditional phase change materials(PCMs)on the temperature-response and lattice deficiencies in versatility cannot satisfy demand for using such materials in complex application scenarios.Here,we introduced metal ions to induce the self-assembly of MXene nanosheets and achieve their ordered arrangement by combining suction filtration and rapid freezing.Subsequently,a series of MXene/K^(+)/paraffin wax(PW)phase change composites(PCCs)were obtained via vacuum impregnation in molten PW.The prepared MXene-based PCCs showed versatile applications from macroscale technologies,successfully transforming solar,electric,and magnetic energy into thermal energy stored as latent heat in the PCCs.Moreover,due to the absence of binder in the MXene-based aerogel,MK3@PW exhibits a prime solar-thermal conversion efficiency(98.4%).Notably,MK3@PW can further convert the collected heat energy into electric energy through thermoelectric equipment and realize favorable solar-thermal-electric conversion(producing 206 mV of voltage with light radiation intensity of 200 mw cm^(−2)).An excellent Joule heat performance(reaching 105℃with an input voltage of 2.5 V)and responsive magnetic-thermal conversion behavior(a charging time of 11.8 s can achieve a thermal insulation effect of 285 s)for contactless thermotherapy were also demonstrated by the MK3@PW.Specifically,as a result of the ordered arrangement of MXene nanosheet self-assembly induced by potassium ions,MK3@PW PCC exhibits a higher electromagnetic shielding efficiency value(57.7 dB)than pure MXene aerogel/PW PCC(29.8 dB)with the same MXene mass.This work presents an opportunity for the multi-scene response and practical application of PCMs that satisfy demand of next-generation multifunctional PCCs. 展开更多
关键词 Self-assembly Multiple-scenario phase change composites Thermal energy storage Electromagnetic interference shielding
下载PDF
Microstructure and damping properties of LPSO phase dominant Mg-Ni-Y and Mg-Zn-Ni-Y alloys 被引量:1
12
作者 Ruopeng Lu Kai Jiao +3 位作者 Nanting Li Hua Hou Jingfeng Wang Yuhong Zhao 《Journal of Magnesium and Alloys》 SCIE EI CAS CSCD 2024年第3期1131-1153,共23页
This work studied the microstructure,mechanical properties and damping properties of Mg_(95.34)Ni_(2)Y_(2.66) and Mg_(95.34)Zn_(1)Ni_(1)Y_(2.66)alloys systematically.The difference in the evolution of the long-period ... This work studied the microstructure,mechanical properties and damping properties of Mg_(95.34)Ni_(2)Y_(2.66) and Mg_(95.34)Zn_(1)Ni_(1)Y_(2.66)alloys systematically.The difference in the evolution of the long-period stacked ordered(LPSO)phase in the two alloys during heat treatment was the focus.The morphology of the as-cast Mg_(95.34)Ni_(2)Y_(2.66)presented a disordered network.After heat treatment at 773 K for 2 hours,the eutectic phase was integrated into the matrix,and the LPSO phase maintained the 18R structure.As Zn partially replaced Ni,the crystal grains became rounded in the cast alloy,and lamellar LPSO phases and more solid solution atoms were contained in the matrix after heat treatment of the Mg_(95.34)Zn_(1)Ni_(1)Y_(2.66)alloy.Both Zn and the heat treatment had a significant effect on damping.Obvious dislocation internal friction peaks and grain boundary internal friction peaks were found after temperature-dependent damping of the Mg_(95.34)Ni_(2)Y_(2.66)and Mg_(95.34)Zn_(1)Ni_(1)Y_(2.66)alloys.After heat treatment,the dislocation peak was significantly increased,especially in the alloy Mg_(95.34)Ni_(2)Y_(2).66.The annealed Mg_(95.34)Ni_(2)Y_(2.66)alloy with a rod-shaped LPSO phase exhibited a good damping performance of 0.14 atε=10^(−3),which was due to the difference between the second phase and solid solution atom content.These factors also affected the dynamic modulus of the alloy.The results of this study will help in further development of high-damping magnesium alloys. 展开更多
关键词 Mg-Ni-Y alloys Mg-Zn-Ni-Y alloys LPSO phase Heat treatment MICROSTRUCTURE Damping properties.
下载PDF
A new insight into LPSO phase transformation and mechanical properties uniformity of large-scale Mg-Gd-Y-Zn-Zr alloy prepared by multi-pass friction stir processing 被引量:1
13
作者 Xiaohu Guan Wen Wang +7 位作者 Ting Zhang Pai Peng Qiang Liu Peng Han Ke Qiao Jun Cai Liqiang Wang Kuaishe Wang 《Journal of Magnesium and Alloys》 SCIE EI CAS CSCD 2024年第5期2041-2056,共16页
A large-scale fine-grained Mg-Gd-Y-Zn-Zr alloy plate with high strength and ductility was successfully prepared by multi-pass friction stir processing(MFSP)technology in this work.The structure of grains and long peri... A large-scale fine-grained Mg-Gd-Y-Zn-Zr alloy plate with high strength and ductility was successfully prepared by multi-pass friction stir processing(MFSP)technology in this work.The structure of grains and long period stacking ordered(LPSO)phase were characterized,and the mechanical properties uniformity was investigated.Moreover,a quantitative relationship between the microstructure and tensile yield strength was established.The results showed that the grains in the processed zone(PZ)and interfacial zone(IZ)were refined from 50μm to 3μm and 4μm,respectively,and numerous original LPSO phases were broken.In IZ,some block-shaped 18R LPSO phases were transformed into needle-like 14H LPSO phases due to stacking faults and the short-range diffusion of solute atoms.The severe shear deformation in the form of kinetic energy caused profuse stacking fault to be generated and move rapidly,greatly increasing the transformation rate of LPSO phase.After MFSP,the ultimate tensile strength,yield strength and elongation to failure of the large-scale plate were 367 MPa,305 MPa and 18.0% respectively.Grain refinement and LPSO phase strengthening were the major strengthening mechanisms for the MFSP sample.In particularly,the strength of IZ was comparable to that of PZ because the strength contribution of the 14H LPSO phase offsets the lack of grain refinement strengthening in IZ.This result opposes the widely accepted notion that IZ is a weak region in MFSP-prepared large-scale fine-grained plate. 展开更多
关键词 Friction stir processing MULTI-PASS Mg-Gd-Y-Zn-Zr alloy LPSO phase transformation Mechanical properties
下载PDF
Fe含量对Al-Fe压铸铝合金导电率及机械性能的影响
14
作者 蒋嗣本 杨阳 陆可馨 《铸造技术》 CAS 2023年第12期1139-1143,共5页
为实现汽车零部件对压铸铝合金导电性、强度、成型性和低成本的需求,以Al-Fe系合金为基础,研究了Fe含量对压铸铝合金导电率和机械性能的影响,进行了微观组织分析和高温性能稳定性验证,并探究了热处理工艺的影响。结果表明,Al-(0.25%~3.0... 为实现汽车零部件对压铸铝合金导电性、强度、成型性和低成本的需求,以Al-Fe系合金为基础,研究了Fe含量对压铸铝合金导电率和机械性能的影响,进行了微观组织分析和高温性能稳定性验证,并探究了热处理工艺的影响。结果表明,Al-(0.25%~3.0%)Fe-0.02%B(质量分数)合金具有良好的压铸成型性,添加Fe可显著提升合金的强度且不造成导电率的大幅下降,Fe含量从0.25%增加到3.0%(质量分数)后,抗拉强度增加130%,导电率仅下降17%。在高温工况下,材料导电率和抗拉强度仅略微下降,表现出较好的高温稳定性。时效处理后导电率提升约1.4%IACS,强度提升约7 MPa。Al-Fe系合金是适合开发兼具高导电、中强度、低成本、可压铸等特点的合金体系。 展开更多
关键词 al-fe合金 压铸 导电率 机械强度 热处理
下载PDF
Crystal structure,phase transitions,and thermodynamic properties of magnesium metavanadate(MgV_(2)O_(6)) 被引量:1
15
作者 Guishang Pei Cheng Pan +2 位作者 Dapeng Zhong Junyi Xiang Xuewei Lv 《Journal of Magnesium and Alloys》 SCIE EI CAS CSCD 2024年第4期1449-1460,共12页
As a promising anode material for magnesium ion rechargeable batteries,magnesium metavanadate(MgV_(2)O_(6))has attracted considerable research interest in recent years.A MgV_(2)O_(6)sample was synthesized via a facile... As a promising anode material for magnesium ion rechargeable batteries,magnesium metavanadate(MgV_(2)O_(6))has attracted considerable research interest in recent years.A MgV_(2)O_(6)sample was synthesized via a facile solid-state reaction by multistep-firing stoichiometric mixtures of MgO and V2O5 powder under an air atmosphere.The solid-state phase transition fromα-MgV_(2)O_(6)toβ-MgV_(2)O_(6)occurred at 841 K and the enthalpy change was 4.37±0.04 kJ/mol.The endothermic effect at 1014 K and the enthalpy change was 26.54±0.26 kJ/mol,which is related to the incongruent melting ofβ-MgV_(2)O_(6).In situ XRD was performed to investigate phase transition of the as-prepared MgV_(2)O_(6)at high temperatures.The cell parameters obtained by Rietveld refinement indicated that it crystallizes in a monoclinic system with the C2/m space group,and the lattice parameters of a=9.280 A°,b=3.501 A°,c=6.731 A°,β=111.76°.The solid-state phase transition fromα-MgV_(2)O_(6)toβ-MgV_(2)O_(6)was further studied by thermal kinetics,indicating that this process is controlled first by a fibril-like mechanism and then by a spherulitic-type mechanism with an increasing heating rate.Additionally,the enthalpy change of MgV_(2)O_(6)at high temperatures was measured utilizing the drop calorimetry,heat capacity was calculated and given as:Cp=208.3+0.03583T-4809000T^(−2)(298-923 K)(J mol^(−1)K^(−1)),the high-temperature heat capacity can be used to calculate Gibbs free energy of MgV_(2)O_(6)at high temperatures. 展开更多
关键词 MgV_(2)O_(6) Crystal structure phase transitions Thermodynamic functions
下载PDF
Heat transfer enhanced inorganic phase change material compositing carbon nanotubes for battery thermal management and thermal runaway propagation mitigation 被引量:1
16
作者 Xinyi Dai Ping Ping +4 位作者 Depeng Kong Xinzeng Gao Yue Zhang Gongquan Wang Rongqi Peng 《Journal of Energy Chemistry》 SCIE EI CAS CSCD 2024年第2期226-238,I0006,共14页
Developing technologies that can be applied simultaneously in battery thermal management(BTM)and thermal runaway(TR)mitigation is significant to improving the safety of lithium-ion battery systems.Inorganic phase chan... Developing technologies that can be applied simultaneously in battery thermal management(BTM)and thermal runaway(TR)mitigation is significant to improving the safety of lithium-ion battery systems.Inorganic phase change material(PCM)with nonflammability has the potential to achieve this dual function.This study proposed an encapsulated inorganic phase change material(EPCM)with a heat transfer enhancement for battery systems,where Na_(2)HPO_(4)·12H_(2)O was used as the core PCM encapsulated by silica and the additive of carbon nanotube(CNT)was applied to enhance the thermal conductivity.The microstructure and thermal properties of the EPCM/CNT were analyzed by a series of characterization tests.Two different incorporating methods of CNT were compared and the proper CNT adding amount was also studied.After preparation,the battery thermal management performance and TR propagation mitigation effects of EPCM/CNT were further investigated on the battery modules.The experimental results of thermal management tests showed that EPCM/CNT not only slowed down the temperature rising of the module but also improved the temperature uniformity during normal operation.The peak battery temperature decreased from 76℃to 61.2℃at 2 C discharge rate and the temperature difference was controlled below 3℃.Moreover,the results of TR propagation tests demonstrated that nonflammable EPCM/CNT with good heat absorption could work as a TR barrier,which exhibited effective mitigation on TR and TR propagation.The trigger time of three cells was successfully delayed by 129,474 and 551 s,respectively and the propagation intervals were greatly extended as well. 展开更多
关键词 Inorganic phase change material Carbon nanotube Battery thermal management Thermal runaway propagation Fire resistance ENCAPSULATION
下载PDF
Transient liquid phase bonding of DD5 superalloy using a designed interlayer: microstructure and mechanical properties 被引量:1
17
作者 周昌杰 范骁乐 +3 位作者 朱立华 陈闯 贺建超 计红军 《China Welding》 CAS 2024年第2期1-10,共10页
Nickel based single crystal superalloy is currently widely used as the material for turbine blades in aerospace engines.However,metallurgical defects during the manufacturing process and damage during harsh environmen... Nickel based single crystal superalloy is currently widely used as the material for turbine blades in aerospace engines.However,metallurgical defects during the manufacturing process and damage during harsh environmental service are inevitable challenges for turbine blades.Therefore,bonding techniques play a very important role in the manufacturing and repair of turbine blades.The transient liquid phase(TLP)bonding of DD5 Ni-based single crystal superalloy was performed using the designed H1 interlayer.A new third-generation Ni-based superalloy T1 powder was mixed with H1 powder as another interlayer to improve the mechanical properties of the bonded joints.The res-ults show that,such a designed H1 interlayer is beneficial to the improvement of shear strength of DD5 alloy bonded joints by adjusting the bonding temperature and the prolongation of holding time.The maximum shear strength at room temperature of the joint with H1 interlayer reached 681 MPa when bonded at 1260℃for 3 h.The addition of T1 powder can effectively reduce holding time or relatively lower bond-ing temperature,while maintaining relatively high shear strength.When 1 wt.%T1 powder was mixed into H1 interlayer,the maximum room temperature shear strength of the joint bonded at 1260℃reached 641 MPa,which could be obtained for only 1 h.Considering the bonding temperature and the efficiency,the acceptable process parameter of H1+5 wt.%T1 interlayer was 1240℃/2 h,and the room tem-perature shear strength reached 613 MPa. 展开更多
关键词 Ni-based superalloy powder transient liquid phase bonded joint shear strength
下载PDF
NUCLEATION BEHAVIOR OF Al_8Fe_4Nd PHASE IN RAPIDLY SOLIDIFIED Al-Fe-V-Si-Nd ALLOY
18
作者 H. Pang, Z.H. Jin, J.N. Deng, and M.G.ZengShenyang National Laboratory for Material Science, Institute of Metal Research, CAS, Shenyang 110016, ChinaCollege of Science, Northeastern University, Shenyang 110004, China 《Acta Metallurgica Sinica(English Letters)》 SCIE EI CAS CSCD 2002年第5期453-459,共7页
The microstructure of Al-Fe-V-Si-Nd alloy prepared by rapid solidification (RS) processing was studied by X-ray diffraction (XRD), transmission electron microscopy (TEM) and high resolution electron microscopy (HREM).... The microstructure of Al-Fe-V-Si-Nd alloy prepared by rapid solidification (RS) processing was studied by X-ray diffraction (XRD), transmission electron microscopy (TEM) and high resolution electron microscopy (HREM). The phase selection of the alloy during solidification and the nucleation behavior of Al8Fe4Nd phase were analyzed within the framework of time-dependent nucleation theory. The incubation time for Al8Fe4Nd phase was found shorter and the nucleation rate higher than those of α-Al. The results indicate the nucleation of Al8Fe4Nd phase is heterogeneous and the dispersoids of Al8Fe4Nd form as primary particles from the liquid, which is consistent with experimental observation. 展开更多
关键词 al-fe based alloy rapid solidification phase selection nucleation behavior
下载PDF
Phase equilibria of Al-Fe-Sn ternary system 被引量:1
19
作者 刘永雄 尹付成 +2 位作者 胡静娴 李智 成思翰 《Transactions of Nonferrous Metals Society of China》 SCIE EI CAS CSCD 2018年第2期282-289,共8页
The isothermal sections of Al-Fe-Sn ternary system at 973 and 593 K were determined experimentally by the equilibriated alloy method using scanning electron microscopy coupled with energy-dispersive spectrometry and X... The isothermal sections of Al-Fe-Sn ternary system at 973 and 593 K were determined experimentally by the equilibriated alloy method using scanning electron microscopy coupled with energy-dispersive spectrometry and X-ray diffractometry. Experimental results show that no ternary compound is found on these two sections. The maximum solubility of Fe in the liquid phase is 1.6%(mole fraction) at 973 K and those of Fe and Al in the liquid phase are 0.6% and 5.1%(mole fraction) at 593 K, respectively. The maximum solubility of Sn in the Fe-Al compounds is 4.2%(mole fraction) at 973 K and 2.3%(mole fraction) at 593 K. All the Fe-Al compounds can be in equilibrium with the liquid phase. 展开更多
关键词 al-fe-Sn ternary system phase diagram SOLUBILITY
下载PDF
Phase2接触单元在岩土工程接触分析中的应用
20
作者 董正中 张帆 何欣 《山西水利》 2024年第7期46-49,共4页
接触分析是工程中岩土体与结构、岩体内部的节理裂隙相互作用时面对的关键问题之一。文章基于Phase2软件接触单元模型,介绍了接触单元的滑移准则,提出了法向刚度和切向刚度这两个参数的估算方法。结果表明:接触单元可以较好地模拟接触... 接触分析是工程中岩土体与结构、岩体内部的节理裂隙相互作用时面对的关键问题之一。文章基于Phase2软件接触单元模型,介绍了接触单元的滑移准则,提出了法向刚度和切向刚度这两个参数的估算方法。结果表明:接触单元可以较好地模拟接触面之间的黏接、脱开、相对滑动这三种状态,强度折减安全系数法的计算结果与Goodman-Bray法计算结果基本一致;接触单元对不同材料之间的接触面模拟有较好的效果,同时接触单元也可选择是否考虑接触面内的孔隙水压力。 展开更多
关键词 phase2 接触单元 法向刚度 切向刚度
下载PDF
上一页 1 2 250 下一页 到第
使用帮助 返回顶部