The influence of different Si contents on the microstructure evolution and mechanical properties of Al⁃Mg⁃Si⁃Cu⁃Zn alloys was systematically studied using tensile testing,OM,SEM,EDS,and EBSD.The results indicate that ...The influence of different Si contents on the microstructure evolution and mechanical properties of Al⁃Mg⁃Si⁃Cu⁃Zn alloys was systematically studied using tensile testing,OM,SEM,EDS,and EBSD.The results indicate that the grain size of as⁃cast alloys was gradually reduced with the increase of the Si content,which mainly resulted from the formation of many iron⁃rich phases and precipitates during the casting process.During homogenization treatment,the plate⁃likeβ⁃AlFeSi phases in the alloy with a higher Si content easily transformed to the sphericalα⁃Al(FeMn)Si phases,which is helpful for improving the formability of alloys.The microstructure evolution of the alloys was also greatly dependent on the content of Si that the number density and homogeneous distribution level of precipitates in the final cold rolled alloys both increased with the increase of the Si content,which further provided a positive effect on the formation of fine recrystallization grains during the subsequent solution treatment.As a result,the yield strength,ultimate tensile strength,and elongation of the pre⁃aged alloys in the direction of 45°with respect to the rolling direction were all increased with increasing Si content.展开更多
The effect of adding 0.03wt%Ni on the microstructure and mechanical properties of Al–Mg–Si–Cu–Zn alloys was systematically studied.The results reveal that the number density of spherical Fe-rich phases within grai...The effect of adding 0.03wt%Ni on the microstructure and mechanical properties of Al–Mg–Si–Cu–Zn alloys was systematically studied.The results reveal that the number density of spherical Fe-rich phases within grains increases with the addition of Ni,accompanied by the formation of Q(Al3Mg9Si7Cu2)precipitates around the spherical Fe-rich phases.Additionally,Ni addition is beneficial to reducing the grain size in the as-cast state.During the homogenization process,Q phases could be completely dissolved and the grain size could remain basically unchanged.However,compared with the Ni-free alloy,the Fe-rich phase in the Ni-containing alloy is more likely to undergo the phase transformation and further form more spherical particles during homogenization treatment.After thermomechanical processing,the distribution of Fe-rich phases in the Ni-containing alloy was further greatly improved and directly resulted in a greater formability than that of the Ni-free alloy.Accordingly,a reasonable Ni addition positively affected the microstructure and formability of the alloys.展开更多
基金Supported by the National Key Research and Development Program of China(Grant No.2016YFB0300801)the National Natural Science Foundation of China(Grant Nos.51871029,51571023 and 51301016)+1 种基金the Beijing Natural Science Foundation(Grant No.2172038)the Government Guided Program Intergovernmental Bilateral Innovation Cooperation Project(Grant No.BZ2019019)
文摘The influence of different Si contents on the microstructure evolution and mechanical properties of Al⁃Mg⁃Si⁃Cu⁃Zn alloys was systematically studied using tensile testing,OM,SEM,EDS,and EBSD.The results indicate that the grain size of as⁃cast alloys was gradually reduced with the increase of the Si content,which mainly resulted from the formation of many iron⁃rich phases and precipitates during the casting process.During homogenization treatment,the plate⁃likeβ⁃AlFeSi phases in the alloy with a higher Si content easily transformed to the sphericalα⁃Al(FeMn)Si phases,which is helpful for improving the formability of alloys.The microstructure evolution of the alloys was also greatly dependent on the content of Si that the number density and homogeneous distribution level of precipitates in the final cold rolled alloys both increased with the increase of the Si content,which further provided a positive effect on the formation of fine recrystallization grains during the subsequent solution treatment.As a result,the yield strength,ultimate tensile strength,and elongation of the pre⁃aged alloys in the direction of 45°with respect to the rolling direction were all increased with increasing Si content.
基金financially supported by the National Key Research and Development Program of China(No.2016YFB0300801)the National Natural Science Foundation of China(Nos.51871029,51571023,and 51301016)+2 种基金Beijing Natural Science Foundation(No.2172038)Beijing Laboratory of Metallic Materials and Processing for Modern Transportation(No.FRF-SD-B-005B)The China Scholarship Council for financial support to M.X.Guo
文摘The effect of adding 0.03wt%Ni on the microstructure and mechanical properties of Al–Mg–Si–Cu–Zn alloys was systematically studied.The results reveal that the number density of spherical Fe-rich phases within grains increases with the addition of Ni,accompanied by the formation of Q(Al3Mg9Si7Cu2)precipitates around the spherical Fe-rich phases.Additionally,Ni addition is beneficial to reducing the grain size in the as-cast state.During the homogenization process,Q phases could be completely dissolved and the grain size could remain basically unchanged.However,compared with the Ni-free alloy,the Fe-rich phase in the Ni-containing alloy is more likely to undergo the phase transformation and further form more spherical particles during homogenization treatment.After thermomechanical processing,the distribution of Fe-rich phases in the Ni-containing alloy was further greatly improved and directly resulted in a greater formability than that of the Ni-free alloy.Accordingly,a reasonable Ni addition positively affected the microstructure and formability of the alloys.
