Al-Mg-Si-Sc alloys with different Mg/Si ratio(<1.73 in wt.% vs>1.73 in wt.%) and different grain size(coarse grains vs ultrafine grains) were prepared, which allowed to investigate the grain size-dependent Mg/Si...Al-Mg-Si-Sc alloys with different Mg/Si ratio(<1.73 in wt.% vs>1.73 in wt.%) and different grain size(coarse grains vs ultrafine grains) were prepared, which allowed to investigate the grain size-dependent Mg/Si ratio effect on the microstructural evolution and concomitantly on the hardness and electrical conductivity when subjected to aging at 200℃. In the coarse-grained Al-Mg-Sc-Sc alloys, the β" precipitation within the grain interior and also the precipitation hardening were highly dependent on the Mg/Si ratio,while the electrical conductivity was slightly affected by the Mg/Si ratio. A promoted β" precipitation was found in the case of Si excess(Mg/Si ratio <1.73), much greater than in the case of Mg excess(Mg/Si ratio>1.73). While in the ultrafine-grained Al-Mg-Si-Sc alloys, the electrical conductivity rather than the hardness was more sensitive to the Mg/Si ratio. The alloy with Si excess displayed electrical conductivity much higher than its counterpart with Mg excess. This is rationalized by the grain boundary precipitation promoted by Si, which reduced the solute atoms and precipitates within the grain interior. Age softening was found in the ultrafine-grained alloy with Si excess, but the ultrafine-grained alloy with Mg excess held the hardness almost unchanged during the aging. The hardness-conductivity correlation is comprehensively discussed by considering the coupling effect of Mg/Si ratio and grain size. A strategy to simultaneously increase the hardness/strength and electrical conductivity is proposed for the Al-Mg-SiSc alloys, based on present understanding of the predominant factors on strengthening and conductivity,respectively.展开更多
A significant size effect is found in the Al3 Sc dispersoid-mediated precipitation in an Al-Mg-Si-Sc alloy.When the Al3 Sc dispersoid size smaller than about 40 nm,β " precipitates nucleate directly on the coher...A significant size effect is found in the Al3 Sc dispersoid-mediated precipitation in an Al-Mg-Si-Sc alloy.When the Al3 Sc dispersoid size smaller than about 40 nm,β " precipitates nucleate directly on the coherent dispersoids and grow by sacrificing the latter.While the dispersoid size greater than^40 nm,Q' and U2 phases are additionally produced that nucleate on the dislocations induced by the semi-/incoherent dispersoids.Mechanical and electrical properties are highly sensitive to the Al3 Sc dispersoid-tuned precipitation.The co-precipitation of β",Q' and U2 phases leads to an obvious improvement in hardness and simultaneously in electrical conductivity.展开更多
Iron （Fe） has a low solid solubility in aluminum （Al）, and it usually forms Fe-rich intermetallic compounds. Scandium （Sc） is an element that can act as a grain refiner, modify the eutectic silicon and change th...Iron （Fe） has a low solid solubility in aluminum （Al）, and it usually forms Fe-rich intermetallic compounds. Scandium （Sc） is an element that can act as a grain refiner, modify the eutectic silicon and change the morphology of Fe-rich intermetallic compounds at the same time. The present work was conducted to study the effect of Sc on the mechanical properties of Al-7Si-0.3Mg. The alloy was prepared by squeeze casting at two levels of Fe （0.2 and 0.4 wt%） and three levels of Sc （0 wt%, 0.2 wt% and 0.4 wt%）. Sc is found to increase the mechanical properties of the alloy, including its hardness, yield strength and ultimate tensile strength. At 0.2 wt% Fe, adding Sc increases the strength while maintaining good elongation. At 0.4 wt% Fe, adding Sc increases the strength but decreases the elongation slightly. The distributions and morphologies of intermetallic compounds and eutectic silicon affect the elongation. Both Fe-rich intermetallic compounds and Sc-rich intermetallic compounds act as crack initiation sites. The 0.2 wt% Fe ＋ 0.2 wt% Sc alloy has the lowest amount of these intermetallic compounds, and eutectic silicon is small and fibrous. So, it has the highest elongation.展开更多
基金financially supported by the National Natural Science Foundation of China (No. 51771147)
文摘Al-Mg-Si-Sc alloys with different Mg/Si ratio(<1.73 in wt.% vs>1.73 in wt.%) and different grain size(coarse grains vs ultrafine grains) were prepared, which allowed to investigate the grain size-dependent Mg/Si ratio effect on the microstructural evolution and concomitantly on the hardness and electrical conductivity when subjected to aging at 200℃. In the coarse-grained Al-Mg-Sc-Sc alloys, the β" precipitation within the grain interior and also the precipitation hardening were highly dependent on the Mg/Si ratio,while the electrical conductivity was slightly affected by the Mg/Si ratio. A promoted β" precipitation was found in the case of Si excess(Mg/Si ratio <1.73), much greater than in the case of Mg excess(Mg/Si ratio>1.73). While in the ultrafine-grained Al-Mg-Si-Sc alloys, the electrical conductivity rather than the hardness was more sensitive to the Mg/Si ratio. The alloy with Si excess displayed electrical conductivity much higher than its counterpart with Mg excess. This is rationalized by the grain boundary precipitation promoted by Si, which reduced the solute atoms and precipitates within the grain interior. Age softening was found in the ultrafine-grained alloy with Si excess, but the ultrafine-grained alloy with Mg excess held the hardness almost unchanged during the aging. The hardness-conductivity correlation is comprehensively discussed by considering the coupling effect of Mg/Si ratio and grain size. A strategy to simultaneously increase the hardness/strength and electrical conductivity is proposed for the Al-Mg-SiSc alloys, based on present understanding of the predominant factors on strengthening and conductivity,respectively.
基金the financial support of the project from the National Natural Science Foundation of China (No. 51771147)。
文摘A significant size effect is found in the Al3 Sc dispersoid-mediated precipitation in an Al-Mg-Si-Sc alloy.When the Al3 Sc dispersoid size smaller than about 40 nm,β " precipitates nucleate directly on the coherent dispersoids and grow by sacrificing the latter.While the dispersoid size greater than^40 nm,Q' and U2 phases are additionally produced that nucleate on the dislocations induced by the semi-/incoherent dispersoids.Mechanical and electrical properties are highly sensitive to the Al3 Sc dispersoid-tuned precipitation.The co-precipitation of β",Q' and U2 phases leads to an obvious improvement in hardness and simultaneously in electrical conductivity.
基金financially supported by the Royal Golden Jubilee Ph.D.Program (No.PHD/0285/2552)the King Mongkut's University of Technology Thonburi,National Metal and Materials Technology Center (No.MT-B-58-MET-07-265-I)
文摘Iron （Fe） has a low solid solubility in aluminum （Al）, and it usually forms Fe-rich intermetallic compounds. Scandium （Sc） is an element that can act as a grain refiner, modify the eutectic silicon and change the morphology of Fe-rich intermetallic compounds at the same time. The present work was conducted to study the effect of Sc on the mechanical properties of Al-7Si-0.3Mg. The alloy was prepared by squeeze casting at two levels of Fe （0.2 and 0.4 wt%） and three levels of Sc （0 wt%, 0.2 wt% and 0.4 wt%）. Sc is found to increase the mechanical properties of the alloy, including its hardness, yield strength and ultimate tensile strength. At 0.2 wt% Fe, adding Sc increases the strength while maintaining good elongation. At 0.4 wt% Fe, adding Sc increases the strength but decreases the elongation slightly. The distributions and morphologies of intermetallic compounds and eutectic silicon affect the elongation. Both Fe-rich intermetallic compounds and Sc-rich intermetallic compounds act as crack initiation sites. The 0.2 wt% Fe ＋ 0.2 wt% Sc alloy has the lowest amount of these intermetallic compounds, and eutectic silicon is small and fibrous. So, it has the highest elongation.
