Effect of slow shot speed on externally solidified crystal,porosity and tensile property in a newly developed high-pressure die-cast Al-Si alloy

The effect of slow shot speed on externally solidified crystal(ESC),porosity and tensile property in a newly developed high-pressure die-cast Al-Si alloy was investigated by optical microscopy(OM),scanning electron microscopy(SEM)and laboratory computed tomography(CT).Results showed that the newly developed AlSi9MnMoV alloy exhibited improved mechanical properties when compared to the AlSi10MnMg alloy.The AlSi9MnMoV alloy,which was designed with trace multicomponent additions,displays a notable grain refining effect in comparison to the AlSi10MnMg alloy.Refining elements Ti,Zr,V,Nb,B promote heterogeneous nucleation and reduce the grain size of primaryα-Al.At a lower slow shot speed,the large ESCs are easier to form and gather,developing into the dendrite net and net-shrinkage.With an increase in slow shot speed,the size and number of ESCs and porosities significantly reduce.In addition,the distribution of ESCs is more dispersed and the net-shrinkage disappears.The tensile property is greatly improved by adopting a higher slow shot speed.The ultimate tensile strength is enhanced from 260.31 MPa to 290.31 MPa(increased by 11.52%),and the elongation is enhanced from 3.72%to 6.34%(increased by 70.52%).

Effect of pressure on microstructures and mechanical properties of Al-Cu-based alloy prepared by squeeze casting

A new high-strength aluminum alloy with better fluidity than that of ZL205A was developed. The effect of applied pressure during squeeze casting on microstructures and properties of the alloy was studied. The results show that the fluidity of the alloy is 16% and 21% higher than that of ZL205A at the pouring temperature of 993 K and 1 013 K, respectively. Compared with permanent-mold casting, mechanical properties of the alloy prepared by squeeze casting are much higher. The tensile strength and elongation of the alloy are 520 MPa and 7.9% in squeeze casting under an applied pressure of 75 MPa, followed by solution treatment at 763 K for 1 h and at 773 K for 8 h, quenching in water at normal temperature and aging at 463 K for 5 h. The improvement of mechanical properties is attributed to the remarkable decreasing of the secondary dendrite arm spacing(SDAS) and eliminating of micro-porosity in the alloy caused by applied pressure.

Thermal Fatigue Behaviour of Co-Based Alloy Coating Obtained by Laser Surface Melt-Casting on High Temperature Alloy

A thermal fatigue behaviour of Co-based alloy coating obtained by laser surface meltcasting on the high temperature alloy GH33 was studied.The results show that after each time of thermal cycling,the final residual stress was formed in the melt-casting layer which is attributed to the thermal stress and structural stress.Through the first 50 times of thermal cycling,the morphology of coating still inherits the laser casting one,but the dendrites get bigger;After the second 50 times of thermal cycling,corrosion pits emerge from coating,and mostly in the places where coating and substrate meet.The fatigue damage type of coating belongs to stress corrosion.

Control of equiaxed grains in a complicated Cu-Ni based alloy prepared by centrifugal casting

A complicated Cu-Ni based alloy was developed to fabricate wear-resisting bush for high temperature application.The concern focuses on the control of equiaxed grains in the developed alloy ingot prepared by centrifugal casting.The results show that the equiaxed grains are determined by the pouring temperature of the melt,the cooling rate and the rotation speed of the mold.With the decrease in pouring temperature,the fraction of the equiaxed grains in the transverse section of the ingot increases and the average length of columnar grain decreases.When the pouring temperature is confined below 1,250℃,complete equiaxed grains can be obtained.Based on the optimal centrifugal casting processing,the tensile strength of the developed alloy ingot with complete equiaxed grains reaches to 810 MPa and 435 MPa at room temperature and 500℃,respectively,which is 14% and 110% higher than that of common commercial QAl10-4-4 alloy.The wear rate of the developed alloy is 7.0 × 10-8 and 3.8 × 10-7 mm3?N-1?mm-1 at room temperature and 500℃,respectively,which is 5 times and 39 times lower than that of QAl10-4-4 alloy.

Influence of the M and M’Metals on the Carbides Population in As-Cast M’-based Alloys Designed to be MC-Strengthened

High temperature applications such as turbine blades for aeronautics or molten glass-shaping tools require the use of refractory metallic materials.Among the later ones,cast superalloys based on some transition metals and reinforced by MC carbides stay in good place and their metallurgy merits to be well known.This work consists in a general exploration of the as-cast microstructures which can be obtained after solidification and solid state cooling down to ambient temperature for a wide series of alloys for which the base element and the MC-former element both vary.For fixed contents in chromium and carbon contents,the compositions of a total of nineteen alloys were considered.These alloys are based on Ni,Co,Fe or Nb and the M content was each time chosen to favor the appearance of TiC,TaC,NbC,HfC or ZrC,as single carbide in a given alloy.After elaboration,metallographic samples were observed by electron microscopy to investigate the obtained microstructures.The obtained results show first that the MC carbides were in many cases successfully obtained at the expense of other possible carbides(for all Co-based alloys for example)but there are also several exceptions(notably for some Nibased alloys).Second,the obtained monocarbides have a eutectic origin and they are script-liked shaped.However they are here too some exceptions,as the rare HfC obtained in a Nb-base).In general,the results obtained in this work show that the principle of dendritic matrix combined with MC carbides with a script-like morphology is not necessarily obtained:the nature of the{base element,MC-former element}combination governs the microstructure of the alloy in its as-cast state for these particular compositions in chromium and carbon.In some cases other carbides may appear and the microstructures may be even of another type.

Formation and mechanical properties of ductile Fe-based amorphous alloys using a cast iron with minor addition of B and Al

Fe-based amorphous alloys with ductility were synthesized using the commercial cast iron QT50 (denoted as QT) with the combining minor addition of B and Al by single roller melt-spinning. The melt-spun (QT1-xBx)99Al1 (x is from 0.006wt% to 0.01wt%) amorphous alloys exhibit onset crystallization temperatures and Curie temperatures of 759-780 and 629-642 K respectively, and whi- ch increase with B content. The amorphous ribbons are ductile and can be bent 180° without breaking. With the increase in B content from 0.006wt% to 0.01wt%, the Vickers microhardness of the amorphous alloys increases from Hv 830 to Hv 1110. The effects of the additional B and Al elements on the glass forming ability and mechanical properties were also discussed.

Influence of high pressure and manganese addition on Fe-rich phases and mechanical properties of hypereutectic Al-Si alloy with rheo-squeeze casting

The influence of high pressure and manganese addition on Fe-rich phases(FRPs)and mechanical properties of Al-14Si-2Fe alloy with rheo-squeeze casting(RSC)was investigated.The semi-solid alloy melt was treated by ultrasonic vibration(UV)firstly,and then formed by squeeze casting(SC).Results show that the FRPs in as-cast SC alloys are composed of coarseβ-Al5(Fe,Mn)Si,δ-Al4(Fe,Mn)Si2 and bone-shapedα-Al15(Fe,Mn)3Si2 phases when the pressure is 0 MPa.With RSC process,the FRPs are first refined by UV,and then the solidification under pressure further causes the grains to become smaller.The peritectic transformation occurs during the formation ofαphase.For the alloy with the same composition,the ultimate tensile strength(UTS)of RSC sample is higher than that of the SC sample.With the same forming process,the UTS of Al-14Si-2Fe-0.8Mn alloy is higher than that of Al-14Si-2Fe-0.4Mn alloy.

Effect of holding pressure on density and cooling rate of cast Al-Si alloy during additive pressure casting

The cast Al-Si alloy was fabricated using the Additive Pressure Casting(APC)method.The effects of holding pressure from 50 to 400 k Pa on the density,cooling rate,and mechanical properties of the alloy,and the corresponding mechanism were discussed.The results indicate that the application of high holding pressure(300 k Pa)enhances the feeding ability of the alloy,leading to an increase of the density.Meanwhile,the cooling rate of the alloy is increased by 100%.In addition,the tensile testing results show that the increase of holding pressure from 50 to 300 k Pa improves the tensile strength and elongation of the alloy by 6.2%and 81.3%,respectively.However,excessive holding pressure(400 k Pa)might lower the density and cooling rate of the alloy due to the feeding channels being blocked.

In-situ observation of porosity formation during directional solidification of Al-Si casting alloys

In-situ observation of porosity formation during directional solidification of two Al-Si alloys (7%Si and 13%Si) was made by using of micro-focus X-ray imaging.In both alloys,small spherical pores initially form in the melt far away from the eutectic solid-liquid (S/L) interface and then grow and coagulate during solidification.Some pores can float and escape from the solidifying melt front at a relatively high velocity.At the end of solidification,the remaining pores maintain spherical morphology in the near eutectic alloy but become irregular in the hypoeutectic alloy.This is attributed to different solidification modes and aluminum dendrite interactions between the two alloys.The mechanism of the porosity formation is briefly discussed in this paper.

Microstructure and Mechanical Properties of Hyper-eutectic Al-Si Alloys Fabricated by Spray Casting

Microstructure and mechanical properties of hyper-eutectic Al-Si alloy fabricated by spray casting were in- vestigated and then these results were compared with those by squeeze cast.The spray-cast specimen was found to have finer Si particles （～5μm） compared to the squeeze-cast specimen （10-25μm）.The tensile strength and elongation of the spray-cast specimen are also higher than those of the squeeze cast one.It was considered that the increased mechanical properties of the spray-cast specimen were mainly due to finer size of the Si particles distributed in Al matrix.

Effects of magnesium and copper additions on tensile properties of Al-Si-Cr die casting alloy under as-cast and T5 conditions

Aluminum high pressure die casting(HPDC)technology has evolved in the past decades,enabling stronger and larger one-piece casting with significant part consolidation.It also offers a higher design freedom for more mass-efficient thin-walled body structures.For body structures that require excellent ductility and fracture toughness to be joined with steel sheet via self-piercing riveting(for instance,shock towers and hinge pillars,etc.),a costly T7 heat treatment comprising a solution heat treatment at elevated temperatures(450℃-500℃)followed by an over-ageing heat treatment is needed to optimize microstructure for meeting product requirement.To enable cost-efficient mass production of HPDC body structures,it is important to eliminate the expensive T7 heat treatment without sacrificing mechanical properties.Optimizing die cast alloy chemistry is a potential solution to improve fracture toughness and ductility of the HPDC components.The present study intends to tailor the Mg and Cu additions for a new Al-Si-Cr type die casting alloy(registered as A379 with The Aluminum Association,USA)to achieve the desired tensile properties without using T7 heat treatment.It was found that Cu addition should be avoided,as it is not effective in enhancing strength while degrades tensile ductility.Mg addition is very effective in improving strength and has minor impact on tensile ductility.The investigated Al-Si-Cr alloy with a nominal composition of Al-8.5wt.%Si-0.3wt.%Cr-0.2wt.%Fe shows comparable tensile properties with the T7 treated AlSi10MnMg alloy which is currently used for manufacturing shock towers and hinge pillars.

Fracture Behaviour of Laser Clad Fe-and Ni-base Alloy Coatings on a Cast Iron under SEMI Loading

Laser cladding technique has been applied to renovate some partially-damaged (or worn) components with Fe, Ni, Co-base alloys, hence to improve their hardness values and wear resistance successfully in previous reports. But for some punching or shearing cast iron dies damaged or worn in automobile manufacture, the renovated surfaces also bear some impact loading. Therefore, a small-energy and multi-impact (SEMI) test was designed to investigate the fracture behaviour of renovated cast iron dies achieved by laser cladding of Fe and Ni-base alloys under SEMI loading to meet above requirement. observations show that the fracture took place in the substrate near to the substrate/coating interface rather than at the interface. The tempering temperature has a great influence on the cycles to fracture of laser-clad samples under SEMl loading, i.e. the low tempering temperature of 300℃ gives a maximum cycle to fracture, while a higher tempering temperature of 400℃ has a minimum. Furthermore, the fracture mechanism has also been discussed in present study

Microstructure and room temperature mechanical properties of NiAl-Cr(Mo)-(Hf,Dy) hypoeutectic alloy prepared by injection casting

The NiA1 Cr（Mo） （Hf, Dy） hypoeutectic alloys were prepared by conventional casting and injection casting techniques respectively, and their microstructure and room temperature mechanical properties were investigated. The results reveal that with the addition of Hf and Dy, the Ni2AIHf Heusler phase and NisDy phase form along the NiAI/Cr（Mo） phase boundaries in intercellular region. By the injection casting method, some Ni2AIHf Heusler phase and NisDy phase transform into Hf and Dy solid solutions, respectively. Moreover, the microstructure of the alloy gets good optimization, which can be characterized by the fine interlamellar spacing, high proportion of eutectic cell area and homogeneously distributed fine Ni2AIHf, NisDy, Hf solid solution and Dy solid solutions. Compared with conventional-cast alloy, the room temperature mechanical properties of injection-cast alloy are improved obviously.

Microstructural characteristics of Al-20Si-2Cu-0.4Mg-1Ni alloy formed by rheo-squeeze casting after ultrasonic vibration treatment

A swash plate for air conditioning compressor of cars was formed by rheo-squeeze casting with semi-solid Al-Si alloy slurry prepared by ultrasonic vibration process, and the microstructure of this alloy was investigated. Besides the microstructures of primary Si particles and α(Al)+β-Si eutectic phases, non-equilibrium α(Al) particles or dendrites are discovered in the microstructure of the Al-20Si-2Cu-0.4Mg-1Ni alloy. Rapid cooling generated by squeeze casting process rather than the pressure is considered as the main reason for the formation of non-equilibrium α(Al) phase. The sound pressurizing effect of ultrasonic vibration also enables the non-equilibrium α(Al) phases to form above eutectic temperature and grow into non-dendritic spheroids in the process of semi-solid slurry preparation. Non-equilibrium α(Al) phases formed in the hypereutectic Al-Si alloy with ultrasonic vibration treatment, consist of round α(Al) grains formed above the eutectic temperature and a small amount of fine α(Al) dendrites formed under the eutectic temperature. The volume fraction of primary Si particles is decreased significantly by the effect of ultrasonic vibration through increasing the solid solubility of Si atoms in α(Al) matrix and decreasing the forming temperature range of primary Si particles. The average particle diameter and the volume fraction of primary Si particles in microstructure of the swash-plate by rheo-squeeze casting are 24.3 μm and 11.1%, respectively.

Microstructure evolution and phase transformation of traditional cast and spray-formed hypereutectic aluminium-silicon alloys induced by heat treatment

Microstructural evolution and phase transformation induced by different heat treatments of the hypereutectic aluminium-silicon alloy, Al-25Si-5Fe-3Cu （wt%, signed as 3C）, fabricated by traditional cast （TC） and spray forming （SF） processes, were investigated by differential scanning calorimetry （DSC） and scanning electron microscopy （SEM） combined with energy dispersive X-ray spectroscopy and X-ray diffraction techniques. The results show that A17Cu2Fe phase can be formed and transformed in TC- and SF-3C alloys between 802-813 K and 800-815 K, respectively. The transformation from β-Al5FeSi to δ-Al4FeSi2 phase via peritectic reaction can occur at around 858-870 K and 876-890 K in TC- and SF-3C alloys, respectively. The starting precipitation temperature of δ-Al4FeSi2 phase as the dominant Fe-bearing phase in the TC-3C alloy is 997 K and the exothermic peak about the peritectic transformation of δ-Al4FeSi2→β-Al5FeSi is not detected in the present DSC experiments. Also, the mechanisms of the microstructural evolution and phase transformation are discussed.

Research progress on refractory composition and deformability of shell molds for TiAl alloy castings

At present, most TiAl components are produced by an investment casting process. Environmental and economic pressures have, however, resulted in a need for the industry to improve the current casting quality, reduce manufacturing costs and explore new markets for the process. Currently, the main problems for investment casting of TiAl alloys are cracks, porosities, and surface defects. To solve these problems, many studies have been conducted around the world, and it is found that casting defects can be reduced by improving composition and properties of the shell molds. It is important to make a summary for the related research progress for quality improvement of TiAl castings. So, the development on refractory composition of shell molds for TiAl alloy investment castings was reviewed, and research progress on deformability of shell mold for TiAl alloy castings both at home and abroad in recent years was introduced. The existing methods for deformability characterization and methods for improving the deformability of shell molds were summarized and discussed. The updated advancement in numerical simulation of TiAl alloy investment casting was presented, showing the necessity for considering the deformability of shell mold during simulation. Finally, possible research points for future studies on deformability of shell mold for TiAl alloy investment casting were proposed.

Semisolid casting with ultrasonically melt-treated billets of Al-7mass%Si alloys

Abstract： The demand for high performance cast aluminum alloy components is often disturbed by increasing impurity elements, such as iron accumulated from recycled scraps. It is strongly required that coarse plate-like iron compound of β-Al5FeSi turns into harmless form without the need for applying refining additives or expensive virgin ingots. The microstructural modification of Al-7mass%Si alloy billets with different iron contents was examined by applying ultrasonic vibration during the solidification. Ultrasonically melt-treated billets were thixocast right after induction heating up to the semisolid temperature of 583 ℃, the microstructure and tensile properties were evaluated in the thixocast components. Globular primary reAl is required to fill up a thin cavity in thixocasting, so that the microstructural modification by ultrasonic melt-treatment was firstly confirmed in the billets. With ultrasonic melt-treatment in the temperature range of 630 ℃ to 605 ℃, the primary α-AI transforms itself from dendrite into fine globular in morphology. The coarse plate-like β-AIsFeSi compound becomes markedly finer compared with those in non-treated billets. Semisolid soaking up to 583 ℃, does not appreciably affect the size of β-AIsFeSi compounds; however, it affects the solid primary reAl morphology to be more globular, which is convenient for thixocasting. After thixocasting with preheated billets, eutectic silicon plates are extremely refined due to the rapid solidification arising from low casting temperature. The tensile strength of thixocast samples with different iron contents does not change much even at 2mass% of iron, when thixocast with ultrasonically melt-treated billets. However, thixocast AI-7mass%Si-2mass%Fe alloy with non-treated billets exhibits an inferior strength of 80 MPa, compared with 180 MPa with ultrasonically melt-treated billets. The elongation is also improved by about a factor of two in thixocastings with ultrasonically melt-treated billets for all iron contents of AI-7mass%Si alloys, for example, the elongation of 11% in thixocast of AI-7mass%Si-0.5mass%Fe alloy with ultrasonically melt-treated billets, 5% in that with non-treated billets.

Effects of Solution Treatment Time and Sr-Modification on Microstructure and Mechanical Property of Al-Si Piston Alloy

The purpose of this paper was to investigate the effects of solution treatment time and Sr-modification on the microstructure and property of the Al-Si piston alloy.It was found that as-cast microstructures of unmodified and Sr-modified Al-Si alloys consisted of a coarse acicular plate of eutectic Si,Cu_3NiAl_6 and Mg_2Si phases in theα-Al matrix but different in size and morphology.Both size and inter-particle spacing of Si particles were significantly changed by increasing the solution treatment time.After a short solution treatment,the coarse acicular plate of the eutectic Si appears to be fragmented.Fully modified microstructure of Sr-modified alloy can reduce the solution treatment time compared to unmodified alloy.The maximum of a peak hardness value is found in the very short solution treatment of both Al-Si piston alloys.Compared to 10 h solution treatment,the solution treatment of 2-4 h is sufficient to achieve appropriate microstructures and hardness. The short solution treatment is very useful to increase the productivity and to reduce the manufacturing cost of the Al-Si piston alloys.

SOLIDIFYING STRUCTURES OF Al_2O_3 SHORT FIBER／Al－Si ALLOY MATRIX COMPOSITE PREPARED BY SQUEEZE CASTING

ＳＯＬＩＤＩＦＹＩＮＧＳＴＲＵＣＴＵＲＥＳＯＦＡｌ_２Ｏ_３ＳＨＯＲＴＦＩＢＥＲ／Ａｌ－ＳｉＡＬＬＯＹＭＡＴＲＩＸＣＯＭＰＯＳＩＴＥＰＲＥＰＡＲＥＤＢＹＳＱＵＥＥＺＥＣＡＳＴＩＮＧ￥Ｚｈａｎｇ，Ｓｉｑｉ；Ｈｕａｎｇ，Ｊｉｎｓｏｎｇ；Ｓｈｅｎ，Ｊｉａｎ；...

Refractory Hard Alloys Elaborated by Casting of Ternary (Co, Ni Fe)-30Cr-2.5 to 5 wt% C Compositions

Three series of ternary alloys of the {M-30Cr-xC}-type with M = Co, Ni or Fe and x ranging from 2.5 to 5 wt% were elaborated by casting. Their microstructure characterizations by XRD and SEM show that very high volume fractions in chromium carbides (even more than 50%) may be obtained in a metallic matrix by this way. However graphite may also appear in very low quantities in the carbon-richest alloys. The hardness increases with the carbon content (up to 1000 Hv30kg) but it may be a little lowered when graphite is also present. The results show that very hard alloys may be simply obtained by casting of rather cheap elements.