Synergistic effect of gradient Zn content and multiscale particles on the mechanical properties of Al-Zn-Mg-Cu alloys with coupling distribution of coarse-fine grains

This study investigated the influence of graded Zn content on the evolution of precipitated and iron-rich phases and grain struc-ture of the alloys,designed and developed the Al–8.0Zn–1.5Mg–1.5Cu–0.2Fe(wt%)alloy with high strength and formability.With the increase of Zn content,forming the coupling distribution of multiscale precipitates and iron-rich phases with a reasonable matching ratio and dispersion distribution characteristics is easy.This phenomenon induces the formation of cell-like structures with alternate distribu-tion of coarse and fine grains,and the average plasticity–strain ratio(characterizing the formability)of the pre-aged alloy with a high strength is up to 0.708.Results reveal the evolution and influence mechanisms of multiscale second-phase particles and the corresponding high formability mechanism of the alloys.The developed coupling control process exhibits considerable potential,revealing remarkable improvements in the room temperature formability of high-strength Al–Zn–Mg–Cu alloys.

Ageing behavior of an Al-Zn-Mg-Cu alloy pre-stretched thick plate

The ageing behavior of a pre-stretched thick plate of Al-Zn-Mg-Cu alloy was systemically studied including one-step ageing, two-step ageing, and retrogression and reageing treatment （RRA）. One-step ageing of the alloy resulted in peak ultimate tensile strengths of 595 and 575 MPa after 22 and 6 h at 120 and 135°C, respectively. The strengthening phase in peak aged （T6 temper） alloy contained GP zones and the η′ phase predominantly. After two-step ageing, the electrical conductivity was increased markedly, but the pre-stretched thick plate sacrificed a great loss of strength. RRA treatment provided a method for maintaining the strength close to that obtained by T6 temper and for obtaining the high electrical conductivity close to that obtained by T7 temper; the ultimate tensile strength and electrical conductivity were 583 MPa and 21.0 MS/m, respectively. TEM analysis of T7 and RRA specimens revealed two types of precipitates that contributed to age strengthening i.e. the η′ and η phases.

Microstructure and properties of an Al-Zn-Mg-Cu alloy pre-stretched plate under various ageing conditions

The microstructures after various ageing treatments and their relation to the strength, fracture toughness, and corrosion behavior of an Al-Zn-Mg-Cu alloy pre-stretched plate were investigated. The results show that retrogression and reaging （RRA） treatment led to a combination of high strength and stress corrosion cracking （SCC） resistance of the alloy. The TEM microstructure of the RRA-treated alloy is a distribution of very fine precipitates in the aluminum matrix grains, similar to that obtained under T6 condition, and the distribution of coarse η MgZn2 precipitates on the grain boundaries similar to that obtained by T7 temper. SEM observations revealed that most of the intergranular fracture characteristics were present on the fracture surface of both the T6 and RRA-treated specimens. On the contrary, the fractographs of the T7 treated specimens mainly consisted of dimple-type ductile transgranular fracture with minor intergranular cracking.

Effect of heat treatment on microstructures and mechanical properties of a bulk nanostructured Al-Zn-Mg-Cu alloy

A bulk nanostructured Al-10.0Zn-2.8Mg-1.8Cu alloy was synthesized by cryomilling first and then by spark plasma sintering （SPS）, and the effect of heat treatment on the microstructures and mechanical properties of this alloy were studied. Most MgZn2 particles with a coarse size lie on the grain boundaries of the SPS-processed sample. After solid solution and artificial aging, fine spherical-like MgZn2 particles precipitate uniformly in the grain interiors. No obvious grain growth is found after the heat treatment. A nanoindentation study indicates that no clear change is found in the Yong＇s modulus of the nanostructured alloy after the heat treatment. However, the hardness of the nanostructured alloy increases by about 33% after the heat treatment, which is attributed to the effect of precipitation-hardening.

Grain refinement and macrosegregation behavior of direct chill cast Al-Zn-Mg-Cu alloy under combined electromagnetic fields

The combined electromagnetic fields were achieved by the application of an alternating magnetic field and a stationary magnetic field and were used during direct chill(DC) casting process to control the microstructure and macrosegregation of an Al-Zn-Mg-Cu alloy. Ingot microstructures were analyzed under an optical microscope(Leica DMR). The composition at different locations in the ingots was measured with inductively coupled plasma mass spectrometry(ICP) method. The results showed that the grain structure is transformed from dendrite to equiaxed structure and significantly refined with the application of combined electromagnetic fields. The uniformity of microstructure is also greatly improved. The combined electromagnetic fields show a significant effect on the distribution of elements. The negative macrosegregation in the centre area of the ingot is obviously reduced.

Effect of minor Sc and Zr addition on microstructures and mechanical properties of Al-Zn-Mg-Cu alloys

Three kinds of Al-Zn-Mg-Cu based alloys with 0.22%, 0.36%(Sc+Zr) (mass fraction, %), and without Sc, Zr addition were prepared by ingot metallurgy. By using optical microscopy, transmission electronic microscopy and scanning electron microscopy, the effects of microalloying elements of Sc, Zr on the microstructure of super-high-strength Al-Zn-Mg-Cu alloys related to mechanical properties were investigated. The tensile properties and microstructures of the studied alloys under different heat treatment conditions were studied. The addition of minor Sc, Zr results in the formation of Al3(Sc,Zr) particles. These particles are highly effective in refining the microstructures, retarding recrystallization, pinning dislocations and subboundaries. The strength of Al-Zn-Mg-Cu alloys was greatly improved by simultaneously adding minor Sc, Zr, meanwhile the ductility of the studied alloys remains at a higher level. The 0.36%(Sc+Zr) alloys gain the optimal properties after 465 ℃/h solution and 120 ℃/24 h aging. The increment of strength is mainly due to strengthening of fine grain and substructure and precipitation of Al3(Sc, Zr) particles.

As-cast microstructure of Al-Zn-Mg and Al-Zn-Mg-Cu alloys added erbium

The effects of different contents of rare earth element, and erbium, on the as-cast microstructures of Al-6Zn-2Mg and Al-6Zn-2Mg-1.8Cu alloys were studied by optical microscopy, scanning electron microscopy, X-ray diffractometry, transmission electron microscopy and EDS analysis. The results show that the netlike structure of as-cast alloys can be remarkably refined, and the distance of dendritic structure decreases, with Er addition. However, the improvement results on Al-Zn-Mg-Cu are not better than that of Al-Zn-Mg. Er and Al can interact to form Al3Er phase, which is coherent with α（Al） matrix, with trace Er addition to the Al-Zn-Mg alloy. The refinement effect of Al-Zn-Mg alloys is familiar with the formation and precipitation of coherent Al3Er phases. The ternary compound AlCuEr, similar with AlCuSc phase, will form when Er is added to Al-Zn-Mg-Cu alloy, which suppresses the formation of Al3Er phase and doesnt solve in the following heat treatment.

Redistribution and re-precipitation of solute atom during retrogression and reaging of Al-Zn-Mg-Cu alloys

The redistribution and re-precipitation of solute atom during retrogression and reaging of three different Al-Zn-Mg-Cu aluminum alloys were investigated. The results of hardness and tensile strength test indicate that after pre-aging at 100 ℃ or 120 ℃ and retrogressing at 200 ℃ for various time and re-aging treatment, the hardness and strength of the alloys are all larger than those under pre-aging condition, some of them even exceed the value under peak aging(T6) condition. TEM observation shows that the PFZ formed during retrogressing in short time becomes narrow and even disappears after re-aging treatment. However, the PFZ formed during retrogressing for a long time does not narrow after re-aging treatment. It is suggested that the redistribution and re-precipitation of solute atom during re-aging treatment result in the narrowing and even disappearance of the PFZ formed during retrogression, which reinforces the grain-boundaries and presents the value of tensile strength exceeding peak-aging strength in the RRA condition, while the precipitates in the matrix of the alloys still keep or even exhibit a more dispersed distribution, and a

Evolution of eutectic structures in Al-Zn-Mg-Cu alloys during heat treatment

The evolution of the eutectic structures in the alloys with different copper contents during heat treatment was studied by scanning electron microscopy(SEM), energy dispersive X-ray spectroscopy(EDS), and differential scanning calorimetry(DSC). The as cast microstructures involve α(Al), eutectic(α(Al) + Mg(Al, Cu, Zn)2) and Al7Cu2Fe. The Al2CuMg particles form during heat treatment. The volume of coarse phases decreases quickly in the initial 12 h during heat treatment. The volume of coarse phases change a little at 400 and 420 ℃. Copper content has a great influence on the evolution of the eutectic. The coarse phases dissolve slowly in alloy with higher copper content.

Age-hardening characteristic of an Al-Zn-Mg-Cu alloy produced by spray deposition

Al-10.8Zn-2.8Mg-1.9Cu alloy was synthesized by spray atomization and deposition technique. GP zones and age-hardening process in the alloy were investigated using high-resolution electron microscopy （HREM）, selected area diffraction （SAD）, and differential scanning calorimetry （DSC） analysis. The results indicated that spray deposition process accelerated the aging kinetics of the alloy at an aging temperature of 120℃, thereby reducing the peak aging time to 16 h. GPⅠ and GPⅡ are the two types of zones that are major precipitates for the alloy under peak-aged condition. The precipitation sequence for the alloy is also discussed.

Effect of additional elements on aging behavior of Al-Zn-Mg-Cu alloys by spray forming

The microstructure and aging behavior of spray formed Al-Zn-Mg-Cu alloys were investigated as a function of alloying element addition. It is revealed that the grains of the as-deposited alloys are refined with increasing Zn element, while the function of Ni addition is to reduce grain boundary particles and eutectic in the as-extruded condition. Particles containing Mg and Zn are found to increase with Zn content increasing, while the role of Ni is to reduce both the number and size of these particles. After uniform heat treatment, parts of educts in grain boundary have melted and the grains have not grown up obviously. After heat extrusion, the microstructure becomes denser and there are many precipitated phases in cross-section while there are second phase arranging along extruded direction in longitudinal section. During artificial aging, the increment of Zn content produces not much effect on peak hardness, in addition to an accelerated overage softening. An addition of about 0.13%Ni, however, gives rise to not only improved peak hardness but also an improvement of property stability at the ageing temperature.

Deep-cryogenic-treatment-induced phase transformation in the Al-Zn-Mg-Cu alloy

An aluminum alloy （Al-Zn-Mg-Cu） subjected to deep cryogenic treatment （DCT） was systematically investigated. The results show that a DCT-induced phase transformation varies the microstructures and affects the mechanical properties of the Al alloy. Both Guinier-Preston （GP） zones and a metastableη′phase were observed by high-resolution transmission electron microscopy. The phenomenon of the second precipitation of the GP zones in samples subjected to DCT after being aged was observed. The viability of this phase transfor-mation was also demonstrated by first-principles calculations.

Production of high strength Al-Zn-Mg-Cu alloys by spray forming process

High strength Al Zn Mg Cu alloys were produced by spray forming process, and compacted by hot extrusion. The results show that the as deposited billets have fine grained microstructure and low porosity. After heat treatment, mechanical properties increase greatly: tensile strength up to 754 MPa, yield strength up to 722 MPa, fracture elongation up to 8%, and elastic modulus up to 72 GPa, respectively. [

Solidification microstructures of Al-Zn-Mg-Cu alloys prepared by spraydeposition and conventional casting methods

High strength Al-Zn-Mg-Cu alloys were prepared by spray deposition and casting techniques. The microstructures of the Al-Zn-Mg-Cu alloys were studied using scanning electron microscopy, transmission electron microscopy, and X-ray diffraction. Secondary phases in the microstructures of the alloys prepared by spray deposition and conventional cast were examined. The results indicate that under the conventional casting condition, the microstructure of the alloy revealed the presence of coarse Al/Mg（ZnCu）2 eutectic phases, and the spray deposited process causes an obvious modification in size, morphology, and distribution of secondary phases in the microstructure as well as reduction of segregation. The superior microstructure of the spray-deposited Al-Zn-Mg-Cu alloy was attributed to the high cooling rate, and associated with the rapid solidification process.

Corrosion behavior of two heat treatment Al-Zn-Mg-Cu alloys in different intergranular corrosion solution

The electrochemical behavior of two kinds of artificial aged Al-Zn-Mg-Cu alloys in two intergranular corrosion （IGC） solutions were studied using electrochemical impedance spectroscopy （EIS） and open circuit potential （OCP） at steady-state. EDAX result indicates that different artificial ageing methods change the composition and content of Cu and Zn in different zones. Zn/Cu depleted precipitation-free zone that plays a very important role in IGC is formed by heating the solubilized Al alloy for 135 ℃ at 16 h. All impedance spectra of the two alloys in two IGC solutions can be divided into three types. The two different states Al alloys takes on one time constant and two capacitive arcs at high-mediate frequency and low frequency in the NaCl+（NH4）2SO4 solution respectively; but in the NaCl+HCl solution, impedance displays one capacitive arc at the high-mediate frequency and an inductive loop at low frequency. OCP results show that more micro-galvanic cells in the NaCl+（NH4）2SO4 solution than that in the NaCl+HCl solution results in more potential fluctuation amplitude, and long-term drift of OCP is due to the long-term variation of the cathodic and anodic corrosion processes.

Small Angle X-ray Scattering Study of Precipitation Kinetics in Al-Zn-Mg-Cu Alloys

The evolution of microstructure parameters （precipitate size and volume fraction） for two types of Al-Zn-Mg-Cu alloys （7075 and 7055） during aging has been studied by synchrotron-radiation small angle X-ray scattering （SAXS）.The results show that the precipitates are only a few nanorneters for both alloys ageing even at higher temperature of 160℃ for 72 h （4.44 and 5.82 nm, respectively）. The maximum of the precipitate volume fraction increases with in creasing Zn content and is about 0.023-0.028 and 0.052-0.054, respectively. The coarsening of precipitate is consistent with LSW （Lifshitz-Slyozov-Wagner） model even at the initial stage where volume fraction is still varying.The activation energy of coarsening regime has been determined to be about 1.22±0.02 eV and 1.25±0.02 eV for alloys 7075 and 7055, respectively.

Influence of exfoliation corrosion on tensile properties of a high strength Al-Zn-Mg-Cu alloy

高强度 Al-Zn-Mg-Cu 合金的张力的性质上的脱落腐蚀的影响被周围的温度调查张力的严峻的、光显微镜学，传动电子显微镜学(TEM ) ，扫描电子显微镜学(SEM ) 和电子反散射衍射(EBSD ) 。在脱落腐蚀沉浸以后，水泡和腐蚀坑能在表表面上被看见，它导致材料和槽口的损失。很多个 intergranular 裂缝被观察在导致腐蚀的槽口的底部开始并且很快宣传进体积材料在期间张力。因而，脱落腐蚀导致力量和易碎的骨折的重要损失。EBSD 结果证明裂缝繁殖路径主要沿着有 45

Effect of Pre-Aging, Over-Aging and Re-Aging on Exfoliation Corrosion and Electrochemical Corrosion Behavior of Al-Zn-Mg-Cu Alloys

By means of TEM, hardness, conductivity, tensile strength test, fracture toughness test, polarization curve and EIS, the Al-Zn-Mg-Cu alloys treated by a new multi-stage aging system, i.e. pre-aging, over-aging and re-aging (120°C/24h + 160°C/8h + 120°C/24h), were characterized. It is found that compared with the Al-Zn-Mg-Cu alloys treated by T76 (120°C/24h + 160°C/8h), the new multi-stage aging treatment can improve the tensile strength, fracture toughness, hardness and conductivity of the alloys at the same time. This is mainly due to the pre-aging, over-aging and re-aging process of super high strength aluminum alloys. Compared with the two-stage over aging process, the formation of multi-stage multi-phase precipitation structure can improve the strength, toughness and corrosion resistance of the alloys at the same time. The polarization curve is consistent with the conclusion. Therefore, we conducted this study to test how the comprehensive properties of the alloy can be improved.

Temperature field in the hot-top during casting a new super-high strength Al-Zn-Mg-Cu alloy by low frequency electromagnetic process

The billets of a new super-high strength Al-Zn-Mg-Cu alloy in 200mm diameter were produced by the processesof low frequency electromagnetic casting (LFEC) and conventional direct chill (DC) casting, respectively. The effects of lowfrequency electromagnetic field on temperature field of the melt in the hot-top were investigated by temperaturemeasurement method. Temperature curves were measured from the surface to the center of the billets by locating type Kthermocouples into the casting during the processes. The results show that during LFEC process the temperature field inthe melt applying the hot-top is very uniform, which is helpful to reduce the difference of thermal gradients between thesurface and the center, and then to reduce the thermal stress and to eliminate casting crack.

Preparation of Al-Zn-Mg-Cu alloy semisolid slurry through a water-cooled serpentine pouring channel

The semisolid slurry of Al-Zn-Mg-Cu alloy was prepared through a self-designed water-cooled copper serpentine pouring channel(WSPC) machine. Influences of pouring temperature, the number of turns and the cooling water flow rate on the microstructure of the semisolid Al-Zn-Mg-Cu alloy slurry were investigated. The results show that the semisolid Al-Zn-Mg-Cu alloy slurry with satisfactory quality can be generated by the WSPC when the pouring temperature is in the range between 680 ℃ and 700 ℃. At a given pouring temperature, the average grain size of primary α-Al decreases and the shape factor increases with the increase of the number of turns. When the cooling water flow rate is 450 L·h^(-1), the obtained semisolid slurry is optimal. During the preparation of the semisolid Al-Zn-Mg-Cu alloy slurry with low superheat pouring, the alloy melt has mixed inhibition and convection flow characteristics by "self-stirring". When the alloy melt flows through the serpentine channel, the chilling effect of the inner wall of the channel, the convection and mixed inhibition of the alloy melt greatly promote the heterogeneous nucleation and grain segregation. This effect destroys the dendrite growth mode under traditional solidification conditions, and the primary nuclei gradually evolve into spherical or nearspherical grains.