Present work encapsulated the friction and wear behaviour of aluminium matrix composites reinforced with different mass fractions of titanium diboride(TiB_(2))particles,synthesized by stir casting.A pin on disc tribot...Present work encapsulated the friction and wear behaviour of aluminium matrix composites reinforced with different mass fractions of titanium diboride(TiB_(2))particles,synthesized by stir casting.A pin on disc tribotester was employed for conducting the dry sliding wear tests of Al2024−TiB_(2)composites.The tests were performed adopting various parameters like load,sliding distance and sliding velocity for investigating the effect of tribological parameters on the prepared composites.Microstructural characterization confirmed uniform dispersion of TiB_(2)particles and good matrix−reinforcement bonding.Results of the experiments revealed that,low friction and wear rates were observed in the developed composites compared to Al2024 alloy,whereas wear rates of both Al2024 alloy and fabricated composites increased with the increase in load,sliding velocity and sliding distance.However,friction coefficient of both Al2024 alloy and fabricated composites reduced with the increase in applied load but rose with the increase in sliding velocity and sliding distance.SEM studies of the worn surfaces and debris depicted that enhancement in wear resistance can be ascribed to finer debris formation.展开更多
The mathematical models are developed to evaluate the ultimate tensile strength( UTS) and hardness of CNTs / Al2024 composites fabricated by high-energy ball milling. The effects of the preparation variables which are...The mathematical models are developed to evaluate the ultimate tensile strength( UTS) and hardness of CNTs / Al2024 composites fabricated by high-energy ball milling. The effects of the preparation variables which are milling time,rotational speed,mass fraction of CNTs and ball to powder ratio on UST and hardness of CNTs / Al2024 composites are investigated. Based on the central composite design( CCD),a quadratic model is developed to correlate the fabrication variables to the UST and hardness. From the analysis of variance( ANOVA),the most influential factor on each experimental design response is identified. The optimum conditions for preparing CNTs / Al2024 composites are found as follows: 1. 53 h milling time,900 r / min rotational speed,mass fraction of CNTs 2. 87% and Ball to powder ratio 25 ∶ 1. The predicted maximum UST and hardness are 273.30 MPa and 261.36 HV,respectively. And the experimental values are 283.25 MPa and256.8 HV,respectively. It is indicated that the predicted UST and hardness after process optimization are found to agree satisfactory with the experimental values.展开更多
Al2024/SiC functionally graded materials (FGMs) with different numbers of graded layers and different amounts of SiC were fabricated successfully by powder metallurgy method and hot pressing process. The effects of in...Al2024/SiC functionally graded materials (FGMs) with different numbers of graded layers and different amounts of SiC were fabricated successfully by powder metallurgy method and hot pressing process. The effects of increasing SiC content and number of layers of Al2024/SiC FGMs on the microstructure and mechanical properties of the composite were investigated. X-ray diffraction (XRD) and scanning electron microscopy (SEM) with energy-dispersive X-ray spectroscopy (EDX) analyses indicated that Al and SiC were dominant components as well as others such as Al4C3, CuAl2, and CuMgAl2展开更多
Pitting corrosion behavior of Al2024 T3 in sodium chloride solution was investigated by using potentiodynamic scanning (PDS) measurements and electrochemical impedance spectroscopy (EIS) technique. When pitting corros...Pitting corrosion behavior of Al2024 T3 in sodium chloride solution was investigated by using potentiodynamic scanning (PDS) measurements and electrochemical impedance spectroscopy (EIS) technique. When pitting corrosion of the alloy occurs, there exists a passive region in the anodic branch of PDS polarization curve, which is enlarged with the increasing of immersion time due to the competition of the halide ions with OH - ions to adsorb on the oxide film to form the corrosion products film and the increase of pitting corrosion area. Two capacitive semicircles were observed in complex plane plot. For more extensive pitting and general corrosion of Al2024 T3, the passive region in PDS disappeared, while another depressed semicircle was observed in Nyquist plot because of the formation of corrosion products film. On the other hand, the low frequency inductive loop, which had often been regarded as a manifestation of pitting or formation and precipitation of a salt film, was not observed, which indicates that the low frequency inductive loop can not be the characteristic of pitting corrosion or the formation of salt film. The results also show that higher reactant CPE exponent values will correspond to more extensive transformation of a metal surface by very localized corrosion, while general corrosion can result in a smaller CPE exponent value.展开更多
In this current work,aluminum alloy grade 2024 is adopted as a plate material that is used in the rolling process with three different parameters including thickness reduction,forming temperature,and density of lubric...In this current work,aluminum alloy grade 2024 is adopted as a plate material that is used in the rolling process with three different parameters including thickness reduction,forming temperature,and density of lubrication type.The experimental procedure of the rolling process is performed using the design of the experiment based on the Taguchi technique(L27),then surface roughness,surface hardness,and surface residual stresses are measured.The results showed that the lubrication density has a significant impact on the surface roughness which depends on the lubrication properties(mineral oil type,natural fat,and kinematic viscosity)while surface hardness and surface residual stresses were strongly affected by thickness reduction.On the other side,the augment in forming temperature can decrease the quality of the final surface finish and the surface hardness but reduce the induced residual stresses.The best surface finish is obtained based on the optimum condition of the rolling factors are(R%_(3),T_(1),andρ_(3))while the optimum condition of rolling parameters that generate higher hardness and compressive residual stresses are(R%_(3)T_(1)ρ_(1)).展开更多
35% SiCp/2024 Al（volume fraction） composite was prepared by powder metallurgy method. The microstructures of Si Cp/Al interfaces and precipitate phase/Al interfaces were characterized by HRTEM, and the interface con...35% SiCp/2024 Al（volume fraction） composite was prepared by powder metallurgy method. The microstructures of Si Cp/Al interfaces and precipitate phase/Al interfaces were characterized by HRTEM, and the interface conditions were evaluated by tensile modules of elasticity and Brinell hardness measurement. The results show that the overall Si Cp/Al interface condition in this experiment is good and three kinds of Si Cp/Al interfaces are present in the composites, which include vast majority of clean planer interfaces, few slight reaction interfaces and tiny amorphous interfaces. The combination mechanism of Si C and Al in the clean planer interface is the formation of a semi-coherent interface by closely matching of atoms and there are no fixed or preferential crystallographic orientation relationships between Si C and Al. MgAl2O4 spinel particles act as an intermediate to form semi-coherent interface with SiC and Al respectively at the slight reaction interfaces. When the composite is aged at 190 °C for 9 h after being solution-treated at 510 °C for 2 h, numerous discoid-shaped and needle-shaped nanosized precipitates dispersively exist in the composite and are semi-coherent of low mismatch with Al matrix. The Brinell hardness of composites arrives peak value at this time.展开更多
文摘Present work encapsulated the friction and wear behaviour of aluminium matrix composites reinforced with different mass fractions of titanium diboride(TiB_(2))particles,synthesized by stir casting.A pin on disc tribotester was employed for conducting the dry sliding wear tests of Al2024−TiB_(2)composites.The tests were performed adopting various parameters like load,sliding distance and sliding velocity for investigating the effect of tribological parameters on the prepared composites.Microstructural characterization confirmed uniform dispersion of TiB_(2)particles and good matrix−reinforcement bonding.Results of the experiments revealed that,low friction and wear rates were observed in the developed composites compared to Al2024 alloy,whereas wear rates of both Al2024 alloy and fabricated composites increased with the increase in load,sliding velocity and sliding distance.However,friction coefficient of both Al2024 alloy and fabricated composites reduced with the increase in applied load but rose with the increase in sliding velocity and sliding distance.SEM studies of the worn surfaces and debris depicted that enhancement in wear resistance can be ascribed to finer debris formation.
基金Sponsored by the Program for Innovative Research Team in University of Yunnan Province and Major Projects of Yunnan Province(Grant No.2014FC001)
文摘The mathematical models are developed to evaluate the ultimate tensile strength( UTS) and hardness of CNTs / Al2024 composites fabricated by high-energy ball milling. The effects of the preparation variables which are milling time,rotational speed,mass fraction of CNTs and ball to powder ratio on UST and hardness of CNTs / Al2024 composites are investigated. Based on the central composite design( CCD),a quadratic model is developed to correlate the fabrication variables to the UST and hardness. From the analysis of variance( ANOVA),the most influential factor on each experimental design response is identified. The optimum conditions for preparing CNTs / Al2024 composites are found as follows: 1. 53 h milling time,900 r / min rotational speed,mass fraction of CNTs 2. 87% and Ball to powder ratio 25 ∶ 1. The predicted maximum UST and hardness are 273.30 MPa and 261.36 HV,respectively. And the experimental values are 283.25 MPa and256.8 HV,respectively. It is indicated that the predicted UST and hardness after process optimization are found to agree satisfactory with the experimental values.
文摘Al2024/SiC functionally graded materials (FGMs) with different numbers of graded layers and different amounts of SiC were fabricated successfully by powder metallurgy method and hot pressing process. The effects of increasing SiC content and number of layers of Al2024/SiC FGMs on the microstructure and mechanical properties of the composite were investigated. X-ray diffraction (XRD) and scanning electron microscopy (SEM) with energy-dispersive X-ray spectroscopy (EDX) analyses indicated that Al and SiC were dominant components as well as others such as Al4C3, CuAl2, and CuMgAl2
文摘Pitting corrosion behavior of Al2024 T3 in sodium chloride solution was investigated by using potentiodynamic scanning (PDS) measurements and electrochemical impedance spectroscopy (EIS) technique. When pitting corrosion of the alloy occurs, there exists a passive region in the anodic branch of PDS polarization curve, which is enlarged with the increasing of immersion time due to the competition of the halide ions with OH - ions to adsorb on the oxide film to form the corrosion products film and the increase of pitting corrosion area. Two capacitive semicircles were observed in complex plane plot. For more extensive pitting and general corrosion of Al2024 T3, the passive region in PDS disappeared, while another depressed semicircle was observed in Nyquist plot because of the formation of corrosion products film. On the other hand, the low frequency inductive loop, which had often been regarded as a manifestation of pitting or formation and precipitation of a salt film, was not observed, which indicates that the low frequency inductive loop can not be the characteristic of pitting corrosion or the formation of salt film. The results also show that higher reactant CPE exponent values will correspond to more extensive transformation of a metal surface by very localized corrosion, while general corrosion can result in a smaller CPE exponent value.
文摘In this current work,aluminum alloy grade 2024 is adopted as a plate material that is used in the rolling process with three different parameters including thickness reduction,forming temperature,and density of lubrication type.The experimental procedure of the rolling process is performed using the design of the experiment based on the Taguchi technique(L27),then surface roughness,surface hardness,and surface residual stresses are measured.The results showed that the lubrication density has a significant impact on the surface roughness which depends on the lubrication properties(mineral oil type,natural fat,and kinematic viscosity)while surface hardness and surface residual stresses were strongly affected by thickness reduction.On the other side,the augment in forming temperature can decrease the quality of the final surface finish and the surface hardness but reduce the induced residual stresses.The best surface finish is obtained based on the optimum condition of the rolling factors are(R%_(3),T_(1),andρ_(3))while the optimum condition of rolling parameters that generate higher hardness and compressive residual stresses are(R%_(3)T_(1)ρ_(1)).
基金Project(51371077)supported by the National Natural Science Foundation of China
文摘35% SiCp/2024 Al（volume fraction） composite was prepared by powder metallurgy method. The microstructures of Si Cp/Al interfaces and precipitate phase/Al interfaces were characterized by HRTEM, and the interface conditions were evaluated by tensile modules of elasticity and Brinell hardness measurement. The results show that the overall Si Cp/Al interface condition in this experiment is good and three kinds of Si Cp/Al interfaces are present in the composites, which include vast majority of clean planer interfaces, few slight reaction interfaces and tiny amorphous interfaces. The combination mechanism of Si C and Al in the clean planer interface is the formation of a semi-coherent interface by closely matching of atoms and there are no fixed or preferential crystallographic orientation relationships between Si C and Al. MgAl2O4 spinel particles act as an intermediate to form semi-coherent interface with SiC and Al respectively at the slight reaction interfaces. When the composite is aged at 190 °C for 9 h after being solution-treated at 510 °C for 2 h, numerous discoid-shaped and needle-shaped nanosized precipitates dispersively exist in the composite and are semi-coherent of low mismatch with Al matrix. The Brinell hardness of composites arrives peak value at this time.
