The precipitation behavior, mechanical properties and corrosion resistance of a novel Al-Zn-Mg-Sc-Zr alloy aged at different time were studied by optical microscopy（OM）, scanning electron microscopy（SEM）, transmis...The precipitation behavior, mechanical properties and corrosion resistance of a novel Al-Zn-Mg-Sc-Zr alloy aged at different time were studied by optical microscopy（OM）, scanning electron microscopy（SEM）, transmission electron microscopy（TEM）, tensile tests, potentiodynamic polarization and electrochemical impedance spectroscopy. The results revealed that with increasing aging time at 120 ℃, the hardness and tensile strength of the alloy increased rapidly at first and then slightly decreased. The resistance of exfoliation corrosion（EXCO） and intergranular corrosion（IGC） increased gradually with increasing aging time. The same trend of corrosion properties was demonstrated by electrochemical polarization curves and EIS test. The characteristics of grain boundary precipitates and precipitate free zone（PFZ） had a significant influence on the mechanical and corrosion behaviors of the studied alloy. On the basis of TEM observations, the size of grain boundary precipitates and the width of PFZ became larger, and the distributed spacing of grain boundary precipitates was enhanced with increasing aging time.展开更多
The Al-9Zn-2.8Mg-2.5Cu-xZr-ySc alloys （x=0, 0.15%, 0.15%; y=0, 0.05%, 0.15%）, produced by low-frequent electromagnetic casting technology, were subjected to homogenization treatment, hot extrusion, solution and agin...The Al-9Zn-2.8Mg-2.5Cu-xZr-ySc alloys （x=0, 0.15%, 0.15%; y=0, 0.05%, 0.15%）, produced by low-frequent electromagnetic casting technology, were subjected to homogenization treatment, hot extrusion, solution and aging treatment. The effects of minor Sc and Zr addition on microstructure, recrystallization and properties of alloys were studied by optical microscopy （OM）, scanning electron microscopy （SEM） and transmission electron microscopy （TEM）. The results show that Sc and Zr addition can refine grains of the as-cast alloy by precipitation of primary Al3（Sc,Zr） particles formed during solidification as heterogeneous nuclei. Secondary Al3（Sc,Zr） precipitates formed during homogenization treatment strongly pin the movement of dislocation and subgrain boundaries, which can effectively inhibit the alloys recrystallization. Compared with the alloy without Sc and Zr addition, the Al-Zn-Mg-Cu-Zr alloy with 0.05%Sc and 0.15%Zr shows the increase in tensile strength and yield strength by 172 MPa and 218 MPa, respectively. Strengthening comes from the contributions of precipitation, substructure and grain refining.展开更多
The precipitation behaviours of Al3Zr precipitate in the Al-Cu-Zr and Al-Cu-Zr-Ti-V alloys were studied by transmission electron microscopy. Metastable Al3Zr precipitates are homogeneously nucleated in dendrite centre...The precipitation behaviours of Al3Zr precipitate in the Al-Cu-Zr and Al-Cu-Zr-Ti-V alloys were studied by transmission electron microscopy. Metastable Al3Zr precipitates are homogeneously nucleated in dendrite centres resulting in homogeneous distribution. However, the precipitation in the interdendritic regions is complex and the precipitation morphologies, helical-like and stripe-like shapes, were observed, which are composed of many spherical Al3Zr precipitates. The stripe-like precipitate clusters have preferential orientations along with the -100- Al directions, which is inferred to be related to θ′（Al2Cu） and θ phases. Addition of Cu can accelerate the L12→D023 structural transformation of the Al3Zr precipitate.展开更多
Al-5.8Mg-0.4Mn-0.25Sc-0.1Zr （mass fraction, %） alloys were prepared by water chilling copper mould ingot metallurgy processing which was protected by active flux. The recrystallization temperature and nucleation mec...Al-5.8Mg-0.4Mn-0.25Sc-0.1Zr （mass fraction, %） alloys were prepared by water chilling copper mould ingot metallurgy processing which was protected by active flux. The recrystallization temperature and nucleation mechanism of the alloy were studied by means of hardness tests, observations of optical microscopy and transmission electron microscopy. The results show that the anti-crystallization ability can be significantly improved by adding minor Sc and Zr into Al-Mg-Mn alloy. This can be proved by a much higher recrystalliztion temperature （450 ~C） than Al-Mg-Mn alloy without Sc and Zr （150 ℃）. The main reason of the great increase of recrystallization temperature can be attributed to the strong pinning effect of highly disperseded Al3（Sc,Zr） particles on dislocations and sub-grain boundaries. The recrystallizing process reveals itself the nucleation mechanism of the alloy involving not only the sub-grain coalescence but also the sub-grain growth.展开更多
基金Project(2012CB619503)supported by the National Basic Research Program of ChinaProjects(51475266,51005134)supported by the National Natural Science Foundation of China
文摘The precipitation behavior, mechanical properties and corrosion resistance of a novel Al-Zn-Mg-Sc-Zr alloy aged at different time were studied by optical microscopy（OM）, scanning electron microscopy（SEM）, transmission electron microscopy（TEM）, tensile tests, potentiodynamic polarization and electrochemical impedance spectroscopy. The results revealed that with increasing aging time at 120 ℃, the hardness and tensile strength of the alloy increased rapidly at first and then slightly decreased. The resistance of exfoliation corrosion（EXCO） and intergranular corrosion（IGC） increased gradually with increasing aging time. The same trend of corrosion properties was demonstrated by electrochemical polarization curves and EIS test. The characteristics of grain boundary precipitates and precipitate free zone（PFZ） had a significant influence on the mechanical and corrosion behaviors of the studied alloy. On the basis of TEM observations, the size of grain boundary precipitates and the width of PFZ became larger, and the distributed spacing of grain boundary precipitates was enhanced with increasing aging time.
基金Project(0211002605132)supported by Institute of Multipurpose Utilization of Mineral Resources,Chinese Academy of Geological Sciences,ChinaProject(0211005303101)supported by the Fundamental Research Funds for the Central Universities,China+1 种基金Project(2010BB4074)supported by Natural Science Foundation Project of CQ CSTC,ChinaProject(2010ZD-02)supported by State Key Laboratory for Advanced Metals and Materials,China
文摘The Al-9Zn-2.8Mg-2.5Cu-xZr-ySc alloys （x=0, 0.15%, 0.15%; y=0, 0.05%, 0.15%）, produced by low-frequent electromagnetic casting technology, were subjected to homogenization treatment, hot extrusion, solution and aging treatment. The effects of minor Sc and Zr addition on microstructure, recrystallization and properties of alloys were studied by optical microscopy （OM）, scanning electron microscopy （SEM） and transmission electron microscopy （TEM）. The results show that Sc and Zr addition can refine grains of the as-cast alloy by precipitation of primary Al3（Sc,Zr） particles formed during solidification as heterogeneous nuclei. Secondary Al3（Sc,Zr） precipitates formed during homogenization treatment strongly pin the movement of dislocation and subgrain boundaries, which can effectively inhibit the alloys recrystallization. Compared with the alloy without Sc and Zr addition, the Al-Zn-Mg-Cu-Zr alloy with 0.05%Sc and 0.15%Zr shows the increase in tensile strength and yield strength by 172 MPa and 218 MPa, respectively. Strengthening comes from the contributions of precipitation, substructure and grain refining.
基金Project (CDJZR12130048) supported by the Fundamental Research Funds for the Central Universities, ChinaProject supported by a Grant from the French Norwegian Foundation for Scientific and Technological Research and Industrial Development
文摘The precipitation behaviours of Al3Zr precipitate in the Al-Cu-Zr and Al-Cu-Zr-Ti-V alloys were studied by transmission electron microscopy. Metastable Al3Zr precipitates are homogeneously nucleated in dendrite centres resulting in homogeneous distribution. However, the precipitation in the interdendritic regions is complex and the precipitation morphologies, helical-like and stripe-like shapes, were observed, which are composed of many spherical Al3Zr precipitates. The stripe-like precipitate clusters have preferential orientations along with the -100- Al directions, which is inferred to be related to θ′（Al2Cu） and θ phases. Addition of Cu can accelerate the L12→D023 structural transformation of the Al3Zr precipitate.
基金Project(2012CB619503)supported by the National Basic Research Program of China
文摘Al-5.8Mg-0.4Mn-0.25Sc-0.1Zr （mass fraction, %） alloys were prepared by water chilling copper mould ingot metallurgy processing which was protected by active flux. The recrystallization temperature and nucleation mechanism of the alloy were studied by means of hardness tests, observations of optical microscopy and transmission electron microscopy. The results show that the anti-crystallization ability can be significantly improved by adding minor Sc and Zr into Al-Mg-Mn alloy. This can be proved by a much higher recrystalliztion temperature （450 ~C） than Al-Mg-Mn alloy without Sc and Zr （150 ℃）. The main reason of the great increase of recrystallization temperature can be attributed to the strong pinning effect of highly disperseded Al3（Sc,Zr） particles on dislocations and sub-grain boundaries. The recrystallizing process reveals itself the nucleation mechanism of the alloy involving not only the sub-grain coalescence but also the sub-grain growth.
