Preparation of Li-B Alloy and Study of Its Microstructure and Discharge Characteristics

A Li-B alloy has been prepared using a pretreated amorphous B powder and pure Li ingot as starting materials by continually slow addition of B powder and intensified stirring in the process of melting. The microstructure and the discharge characteristic of the materials have been investigated- Results show that the problem of temperature control in synthesis would be modified by means of continual addition of B powder, the Li7B6 would be more finely distributed in the metal Li by means of intensified stirring. The discharge characteristic of the Li-B alloy using amorphous B as starting materials is almost the same with that of using crystalline B.

THIN FILM PREPARATION OF AMORPHOUS Ti-Ni ALLOY AND THEIR HYDROGEN ABSORPTION PROPERTIES

Amorphous Ti_(0.88)Ni_(1.00) and Ti_(1.69)Ni_(1.00) alloy films are prepared by means of ion beam sputtering using TiNi and Ti_2Ni alloy targets, respectively. Their hydrogen absorption properties are investigated by a galvanostatic method. The results show th the discharge capacity of the Ti_(1.69)Ni_(1.00) sample is higher than that of the Ti_(0.88)Ni_(1.00) sample. And the film electrodes have high durability and long cycle life.

Preparation and tensile properties of DD5 single crystal castings

The preparation procedure of DD5 single crystal castings was optimized. The microstructure characteristics of DD5 single crystal superalloy were investigated by microstructure observation and segregation behavior examination. The results show that the grain orientation is optimized by constraining the spiral crystallizer in [001] orientation and spatial scale. Also, the γ＇ phase of inter-dendrites is larger and more irregular than that in dendrite arms. High temperature tensile tests of DD5 single crystal castings exhibit that the peak stress increases with increasing temperature, while the area reduction shows an opposite trend, when the temperature is below 800℃; meanwhile, when the temperature is between 800℃ and 1000℃, the fracture stress of the alloy is the same as the peak stress. The fracture mode changes from shear to ductile with increasing temperature from 600℃ and 1000℃.

Microstructure and Mechanical Property of 2024 Aluminium Alloy Prepared by Rapid Solidification and Mechanical Milling

Rapidly solidified 2024 aluminium alloy powders were mechanically milled, then consolidated to bulk form. The microstructural changes of the powders in mechanical milling (MM) and consolidation process were characterized by X-ray diffraction analyses and transmission electron microscopy observations. The results showed that mechanical milling reduced the grain size to nanometer, dissolved the Al2Cu intermetallic compound into the aluminium matrix and produced an aluminium supersaturated solid solution. During consolidation process. the grain size increased to submicrometer, and the Al2Cu and Al2(Cu, Mg, Si, Fe, Mn) compounds precipitated owing to heating. Increasing consolidation temperature and time results in obvious grain growth and coarsening of second phase particles. The tensile yield strength of the consolidated alloy with submicrometer size grains increases with decreasing grain size, and it follows the famous HallPetch relation

Magnetostriction Increase of Tb0.3Dy0.7Fe1.95 Alloy Prepared by Solidification in High Magnetic Fields

Tb0.3Dy0.TFe1.95 alloys are solidified under various high magnetic field conditions. The influence of a high magnetic field on the crystal orientation, morphology and magnetostriction of the alloys are studied. The results show that with the increase of magnetic flux density, the crystal orientation of the （Tb,Dy）Fe2 phase changed from （113） to （111） direction; the grains in the alloys tended to align along the magnetic field direction; and the magnetostriction of Tb0.3Dy0.7Fe1.95 alloys is remarkably improved. The change in magnetostriction of Tb0.3Dy0.TFe1.95 alloys is linked to the amount and the crystal orientation behavior of the （Tb,Dy）Fe2 phase.

Hard Magnetic Properties of Sm-Fe-C Based Alloys Prepared by Mechanical Alloying

The structure and magnetic properties of SmyFe100-1.5yC0.5y(y=8～20) alloys prepared by mechanical alloying (MA) from Sm, Fe and graphite have been investigated systematically. In order to improve hard magnetic properties of the alloys prepared by mechanical alloying, a new method consisting of re-milling and re-annealing was developed. After being re-milled and re-annealed, the Curie temperature TC of the Sm-Fe-C alloys changes. The TC of 2:17 phase increases, whereas the TC of 2:14:1 phase decreases. After being re-annealed at low temperatures, the grain sizes of hard phases are smaller than those in the alloys annealed at high temperatures. The effects of Co or Ti substitution for Fe are studied.

A Preparing Process of Quick-moving Leaf for TiNi Alloy

This paper reports a preparing process of quick moving leaf for TiNi shape memory alloy. Using the process. a series of quick moving leaves having different points of temperature. from 58 to 100℃. at which they jump up have been made. The quick moving leaves will be fully qualified as the electric switches that open and close themselves at proper temperatures.