In order to improve the performance of Al_(2)O_(3)-SiC-C castables for iron trough,samples were prepared using brown corundum,dense corundum,activated alumina micropowder,ball pitch,and silicon as main raw materials,c...In order to improve the performance of Al_(2)O_(3)-SiC-C castables for iron trough,samples were prepared using brown corundum,dense corundum,activated alumina micropowder,ball pitch,and silicon as main raw materials,calcium aluminate cement as the binder.Several kinds of silica fumes(93SiO_(2),96SiO_(2),and 99SiO_(2))with different particle size distributions and chemical composition were added to research the effects on the properties of castables.The results show that the sample with 99SiO_(2) fume has high water requirement for molding,but the bulk density is the lowest,the apparent porosity is the highest,the oxidation resistance is the worst,and the permanent linear change on heating is low after firing at 1 450 ℃ for 3 h.The bulk density and the apparent porosity of the sample with 93SiO_(2) fume or 96SiO_(2) fume are equivalent,the hot modulus of rupture of the sample with 93SiO_(2) fume is the lowest,and the slag resistance of the sample with 96SiO_(2) fume is the best.The comprehensive performance of the sample with 96SiO_(2) fume is the best.展开更多
The abnormal corrosion of hot iron ladles was investigated.The performance,the composition and the structure of bricks for hot iron ladles were analyzed.The results show that(1)compared with the alumina-silicon carbid...The abnormal corrosion of hot iron ladles was investigated.The performance,the composition and the structure of bricks for hot iron ladles were analyzed.The results show that(1)compared with the alumina-silicon carbide-carbon bricks for the ladle bottom,those for the ladle wall have more pyrophyllite and the Al2O3 content of 36.32 mass%;their bulk density,apparent porosity and cold compressive strength are lower than the requirement of industry standard;they have poor anti-oxidation performance and are oxidized to form a porous layer during service,which loosens the brick lining structure thus leading to fracture,local wear and structural damage of bricks;(2)without preheating,steel scraps are not completely melted,resulting in slag or steel attachment at the mouth or the bottom of ladles thus increasing damage of ladles;(3)and the residual bricks react with the attached slag to form low melting point phases affecting their hot properties.The refractories for the lining of hot iron ladles must be improved in combination with process changes,not entirely by raw materials replacement to reduce costs.展开更多
Al2O3-SiC-C specimens were prepared using white fused corundum （3-1,≤1 and ≤0.044 mm）,Al2O3-SiC composite powders （d50 ≤ 5 μm）,α-Al2O3 micropowder （d50 =1.2 μm）,SiC powder （≤ 0.044 mm）,flake graphite （...Al2O3-SiC-C specimens were prepared using white fused corundum （3-1,≤1 and ≤0.044 mm）,Al2O3-SiC composite powders （d50 ≤ 5 μm）,α-Al2O3 micropowder （d50 =1.2 μm）,SiC powder （≤ 0.044 mm）,flake graphite （≤ 0.088 mm）,Si powder （d50 =42.8 μm） and B4C powder （d50 ≤10 μm） as main starting materials,and thermosetting phenolic resin as binder.4%,8%,12% and 16% （in mass,the same hereinafter） of Al2O3-SiC composite powders substituted the same quantity of α-Al2O3 micropowder ＋ SiC powder.Effects of composite powder additions on apparent porosity,bulk density,cold modulus of rupture,cold crushing strength,hot modulus of rupture （1 400 ℃）,thermal shock resistance （1 100 ℃,water quenching） and oxidation resistance （1 000 and 1 500 ℃） of Al2O3-SiC -C specimens after 180 ℃ curing,1 000 ℃ 3 h carbon-embedded firing and 1 500 ℃ 3 h carbon-embedded firing,respectively,were researched.The results indicate that：（1） with the increase of Al2O3-SiC composite powder,cold strengths of the cured specimens decline,those of the specimens fired at 1 000 ℃ change a little,and those of the specimens fired at 1 500 ℃ change a little except for an obvious improvement of cold crushing strength ; （2） with the increase of Al2O3-SiC composite powder,hot modulus of rupture at 1 400 ℃ decreases and thermal shock resistance enhances significantly; （3） when Al2O3-SiC composite powder addition is 4%,the oxidation resistance at 1 500 ℃ is the best,and the reason may be the composite powder is finer and more active,which is beneficial to form dense mullite protective layer to retard the O2 diffusion into the specimens.展开更多
文摘In order to improve the performance of Al_(2)O_(3)-SiC-C castables for iron trough,samples were prepared using brown corundum,dense corundum,activated alumina micropowder,ball pitch,and silicon as main raw materials,calcium aluminate cement as the binder.Several kinds of silica fumes(93SiO_(2),96SiO_(2),and 99SiO_(2))with different particle size distributions and chemical composition were added to research the effects on the properties of castables.The results show that the sample with 99SiO_(2) fume has high water requirement for molding,but the bulk density is the lowest,the apparent porosity is the highest,the oxidation resistance is the worst,and the permanent linear change on heating is low after firing at 1 450 ℃ for 3 h.The bulk density and the apparent porosity of the sample with 93SiO_(2) fume or 96SiO_(2) fume are equivalent,the hot modulus of rupture of the sample with 93SiO_(2) fume is the lowest,and the slag resistance of the sample with 96SiO_(2) fume is the best.The comprehensive performance of the sample with 96SiO_(2) fume is the best.
文摘The abnormal corrosion of hot iron ladles was investigated.The performance,the composition and the structure of bricks for hot iron ladles were analyzed.The results show that(1)compared with the alumina-silicon carbide-carbon bricks for the ladle bottom,those for the ladle wall have more pyrophyllite and the Al2O3 content of 36.32 mass%;their bulk density,apparent porosity and cold compressive strength are lower than the requirement of industry standard;they have poor anti-oxidation performance and are oxidized to form a porous layer during service,which loosens the brick lining structure thus leading to fracture,local wear and structural damage of bricks;(2)without preheating,steel scraps are not completely melted,resulting in slag or steel attachment at the mouth or the bottom of ladles thus increasing damage of ladles;(3)and the residual bricks react with the attached slag to form low melting point phases affecting their hot properties.The refractories for the lining of hot iron ladles must be improved in combination with process changes,not entirely by raw materials replacement to reduce costs.
文摘Al2O3-SiC-C specimens were prepared using white fused corundum （3-1,≤1 and ≤0.044 mm）,Al2O3-SiC composite powders （d50 ≤ 5 μm）,α-Al2O3 micropowder （d50 =1.2 μm）,SiC powder （≤ 0.044 mm）,flake graphite （≤ 0.088 mm）,Si powder （d50 =42.8 μm） and B4C powder （d50 ≤10 μm） as main starting materials,and thermosetting phenolic resin as binder.4%,8%,12% and 16% （in mass,the same hereinafter） of Al2O3-SiC composite powders substituted the same quantity of α-Al2O3 micropowder ＋ SiC powder.Effects of composite powder additions on apparent porosity,bulk density,cold modulus of rupture,cold crushing strength,hot modulus of rupture （1 400 ℃）,thermal shock resistance （1 100 ℃,water quenching） and oxidation resistance （1 000 and 1 500 ℃） of Al2O3-SiC -C specimens after 180 ℃ curing,1 000 ℃ 3 h carbon-embedded firing and 1 500 ℃ 3 h carbon-embedded firing,respectively,were researched.The results indicate that：（1） with the increase of Al2O3-SiC composite powder,cold strengths of the cured specimens decline,those of the specimens fired at 1 000 ℃ change a little,and those of the specimens fired at 1 500 ℃ change a little except for an obvious improvement of cold crushing strength ; （2） with the increase of Al2O3-SiC composite powder,hot modulus of rupture at 1 400 ℃ decreases and thermal shock resistance enhances significantly; （3） when Al2O3-SiC composite powder addition is 4%,the oxidation resistance at 1 500 ℃ is the best,and the reason may be the composite powder is finer and more active,which is beneficial to form dense mullite protective layer to retard the O2 diffusion into the specimens.
