Aiming at improving the properties of magnesia carbon materials,silicon aluminum carbide(Al_(4)SiC_(4))containing materials were prepared using industrial aluminum powder,silicon carbide powder,and graphite as raw mat...Aiming at improving the properties of magnesia carbon materials,silicon aluminum carbide(Al_(4)SiC_(4))containing materials were prepared using industrial aluminum powder,silicon carbide powder,and graphite as raw materials,and activated alumina powder as an additive,mixing thoroughly,pressing into cylinders and then firing at 1200℃for 30 min in a carbon embedded atmosphere by the microwave method.The effects of the aluminum powder addition(20%and 24%,by mass)and activated alumina powder addition(0,3%,5%and 7%,by mass)on the microwave synthesis of Al_(4)SiC_(4) as well as the effect of the obtained Al_(4)SiC_(4) containing material on the properties of magnesia carbon bricks were studied.The results show that:compared with the samples with 20%aluminum powder,those with 24%aluminum powder generate more Al_(4)SiC_(4).With the activated alumina powder addition increasing from 0 to 7%,the amount of Al_(4)SiC_(4) generated increases first and then decreases.Compared with the sample without activated alumina powder,the samples with activated alumina powder show lower bulk density and higher apparent porosity.With the activated alumina powder addition increasing from 3%to 7%,the bulk density of the samples increases first and then decreases,while the apparent porosity of the samples shows an opposite trend.The optimal additions are 24%aluminum powder and 5%activated alumina powder,and Al_(4)SiC_(4) synthesized in this sample has a hexagonal plate structure.With the synthesized Al_(4)SiC_(4) containing material added,the magnesia carbon brick has slightly increased cold modulus of rupture,basically the same modulus of elasticity and improved oxidation resistance.展开更多
Ti-6 Al-4 V alloy powder was processed by electrode induction melting gas atomization(EIGA)at high gas pressure(5.5-7.0 MPa).The effects of atomizing gas pressure on the powder characteristics and the microstructure,a...Ti-6 Al-4 V alloy powder was processed by electrode induction melting gas atomization(EIGA)at high gas pressure(5.5-7.0 MPa).The effects of atomizing gas pressure on the powder characteristics and the microstructure,along with the mechanical properties of the as-fabricated block by laser melting deposition(LMD),were investigated.The results indicate that the diameters of powders are distributed in a wide range of sizes from 1 to 400μm,and the median powder size(d50)decreases with increasing gas pressure.The powders with a size fraction of 100-150μm obtained at gas pressures of 6.0 and 6.5 MPa have better flowability.The oxygen content is consistent with the change trend of gas pressure within a low range of 0.06%-0.20%.Specimens fabricated by LMD are mainly composed ofα+βgrains with a fine lamellar Widmanstatten structures and have the ultimate tensile strength(UTS)and yield strength of approximately 1100 and 1000 MPa,respectively.Furthermore,the atomized powders have a favorable 3 D printing capability,and the mechanical properties of Ti-6 Al-4 V alloys manufactured by LMD typically exceed those of their cast or wrought counterparts.展开更多
This work aimed to fabricate B4C reinforced aluminum matrix composites via blended powder semisolid forming that is an implementation of the benefits of semisolid forming to the powder metallurgy. Al7075 elements were...This work aimed to fabricate B4C reinforced aluminum matrix composites via blended powder semisolid forming that is an implementation of the benefits of semisolid forming to the powder metallurgy. Al7075 elements were incrementally added to ethanol solution under mechanical mixing. Al7075 constituents and B4C particles were blended in a high energy ball mill. Cold compacted Al7075/B4C blends were pressed at semisolid state. The effects of the size of the matrix（20, 45 and 63 μm）, reinforcing volume fraction（5%, 10% and 20%） and semisolid compaction pressure（50 and 100 MPa） on the morphology, microstructure, density, hardness, compression and bending strength were thoroughly analyzed. Experimental results revealed that the highest microstructural uniformity was achieved when large B4C particles（45 μm） were distributed within the small particles（20 μm） of the matrix phase. Composites with matrix particles larger than reinforcing phase indicated agglomerations in loadings more than 10%（volume fraction）. Agglomerated regions resisted against penetration of the liquid phase to the pores and lowered the density and strength of these composites. Composites with 20 μm Al7075 and 20%（volume fraction） 45 μm B4C powder pressed under 100 MPa exhibited the highest values of hardness（HV 190） and compressive strength（336 MPa）.展开更多
Ti6Al4V powders with three different particle size distributions(0–20, 20–45, and 45–75 μm) were used to evaluate the effect of the particle size distribution on the solid-state sintering and their mechanical prop...Ti6Al4V powders with three different particle size distributions(0–20, 20–45, and 45–75 μm) were used to evaluate the effect of the particle size distribution on the solid-state sintering and their mechanical properties. The sintering kinetics was determined by dilatometry at temperatures from 900 to 1260°C. The mechanical properties of the sintered samples were evaluated by microhardness and compression tests. The sintering kinetics indicated that the predominant mechanism depends on the relative density irrespective of the particle size used. The mechanical properties of the sintered samples are adversely affected by increasing pore volume fraction. The elastic Young's modulus and yield stress follow a power law function of the relative density. The fracture behavior after compression is linked to the neck size developed during sintering, exhibiting two different mechanisms of failure: interparticle neck breaking and intergranular cracking in samples with relative densities below and above of 90%, respectively. The main conclusion is that relative density is responsible for the kinetics, mechanical properties, and failure behavior of Ti6 Al4 V powders.展开更多
Ammonium metatungstate and cobalt nitrate were mixed at the molecular level in distilled water and then spray-decomposed to CoWO_4/WO_3 nanocomposite powder.The particle morphology,crystalline size,forming course,chem...Ammonium metatungstate and cobalt nitrate were mixed at the molecular level in distilled water and then spray-decomposed to CoWO_4/WO_3 nanocomposite powder.The particle morphology,crystalline size,forming course,chemical composition and phase structure of the powder were studied by SEM,TEM,DTA-TG,IR and XRD,respectively.Results show that the powder is homogeneous,spherical and nano-aggregated.展开更多
The present study aims to fabricate and evaluate the mechanical properties and wear behavior of Mg metal matrix composite,reinforced by 0,1.5,3,5 and 10 vol.%B4C microparticles.Mg−B4C samples were fabricated at 450℃ ...The present study aims to fabricate and evaluate the mechanical properties and wear behavior of Mg metal matrix composite,reinforced by 0,1.5,3,5 and 10 vol.%B4C microparticles.Mg−B4C samples were fabricated at 450℃ and under different loading rates by using split Hopkinson bar(SHB),drop hammer(DH)and Instron(QS)at strain rates of 1600,800 and 0.008 s–1,respectively.The mechanical properties including microhardness,quasi-static and dynamic compressive strengths and wear behavior of samples were experimentally investigated.The results show that,the hardness of SHB and DH samples is obtained to be 20.2%and 5.7%higher than that of the QS sample,respectively.The wear rate and wear mass loss of Mg–10.0%B4C samples fabricated by SHB were determined lower than those of the QS sample by nearly 33%and 39%,respectively.The quasi-static compressive strengths of Mg−5.0%B4C are improved by 39%,30%and 29%for the SHB,DH and QS samples,respectively,in comparison with the case of pure Mg.Furthermore,it is discovered that the dynamic compressive strength of samples is 51%−110%higher than their quasi-static value with respect to the B4C content.展开更多
The effect of plasma arc powder surfacing process on the amount of B4C particles in the coating and the thermal behavior of B4C particles in different surfacing stages has been investigated.The results showed that the...The effect of plasma arc powder surfacing process on the amount of B4C particles in the coating and the thermal behavior of B4C particles in different surfacing stages has been investigated.The results showed that the feeding rate of B4C partiles is the most important factor affecting the amount of B4C particles in the surfacing coating among all the surfacing parameters,and the most part of B4C Particles in the coating is nto the remainders of original solid B4C particles,but the consolidation products of the unmelted liquid B4C globules in the pool.The results also showed that the B4C particles would not be melted in the plasma arc column, their melting process mainly takes place in the anode spot region on the surface of the pool when surfacing current is less than 200A.展开更多
Taking Ti6Al4V titanium alloy powder as the research object,on the basis of single layer scanning and single channel scanning experiment,this paper studies the influence of selective laser melting(SLM)process paramete...Taking Ti6Al4V titanium alloy powder as the research object,on the basis of single layer scanning and single channel scanning experiment,this paper studies the influence of selective laser melting(SLM)process parameters on Ti6Al4V alloy material formability,and block forming experiment is carried out.Through the design of orthogonal experiment,morphology observation of sample and density analysis,results show that the best block molding parameters of SLM technology in Ti6Al4V alloy powder are laser power of 400 W,lap rate of 1 and the scanning speed of 750 mm/min,density can up to 96.17%.展开更多
Spent pickling liquors pose a serious environmental problem in most industrialized countries, mainly owing to their corrosive properties and their ferrous iron and hydrochloric acid content. In this paper, spent pickl...Spent pickling liquors pose a serious environmental problem in most industrialized countries, mainly owing to their corrosive properties and their ferrous iron and hydrochloric acid content. In this paper, spent pickling liquor was used as an inexpensive raw material to prepare Fe304 magnetic powder via an oxidation method. Being able to recover the dissolved iron from spent pickling liquors would not only salvage a valuable material but also render the effluent environmentally benign. The structure of the Fe_3O_4 magnetic powder was characterized by X-ray diffraction. The morphology and size were characterized by scanning electron microscopy and transmission electron microscopy. Their magnetic properties were tested at room temperature by a vibrating sample magnetometer. In addition, the saturation magnetization of Fe_3 O_4 products can be further enhanced to 96.1 emu/g after purification.展开更多
The Ti−6Al−4V(TC4)alloy powder and forged solid were diffusion bonded by hot isostatic pressing(HIP)to fabricate a powder−solid part.The microstructure of the powder−solid part was observed by scanning electron micros...The Ti−6Al−4V(TC4)alloy powder and forged solid were diffusion bonded by hot isostatic pressing(HIP)to fabricate a powder−solid part.The microstructure of the powder−solid part was observed by scanning electron microscope(SEM).The microhardness and tensile tests were conducted to investigate the mechanical properties.The results showed that the powder compact was near-fully dense,and the powder/solid interface was tight and complete.The microhardness of the interface was higher than that of the powder compact and solid.The fractures of all powder−solid tensile specimens were on the solid side rather than at the interface,which indicated that a good interfacial strength was obtained.The tensile strength and elongation of the powder compact were higher than those of the solid.It is concluded that the HIP process can successfully fabricate high-quality Ti−6Al−4V powder−solid parts,which provides a novel near net shape technology for titanium alloys.展开更多
SiCf/Ti-6Al-4V composites were fabricated by the powder-coated fiber method. The precursor fiber was prepared under the optimized parameter, and the composites were made using the vacuum hot pressure method. The influ...SiCf/Ti-6Al-4V composites were fabricated by the powder-coated fiber method. The precursor fiber was prepared under the optimized parameter, and the composites were made using the vacuum hot pressure method. The influence of heat exposure time on products of thelinterfacial reaction was investigated using scanning electron microscope （SEM） and analytical transmission electron microscope （TEM） with energy dispersive spectrometer （EDS）. The main products are TiC and Ti5Si3 after vacuum exposing the samples at 700℃ for 50 h. The growth dynamics of interracial reaction products was analyzed quantitatively, which fitted the parabola rule. The activity energy of the reaction was 252 kJ·mol^-1.展开更多
In this paper, Pyrolysis Gas Chromatography Mass Spectroscopy is adopted to measure heating release curve of Si 3N 4 ultrafine powder at different temperatures. The results demonstrate that Si 3N 4 mainly adsorbs...In this paper, Pyrolysis Gas Chromatography Mass Spectroscopy is adopted to measure heating release curve of Si 3N 4 ultrafine powder at different temperatures. The results demonstrate that Si 3N 4 mainly adsorbs O 2, N 2, CO 2, NH 3 and H 2O during the storage at room temperature, of which O 2 and N 2 are physisorped and H 2O chemisorped. Hydrolysis reaction is the reason for oxygen increasement and the different states of oxygen can be determined by improved heat extraction. The mechanisms of the reaction speed as well as the formation of different states of oxygen are also discussed.展开更多
In cooperation with figure-of-merits the Rietveld analysis can appraise both angular and intensity data of powder diffraction. In this work, X-ray diffraction pattern of Bi4(SiO4)3 was redetermined with intensity figu...In cooperation with figure-of-merits the Rietveld analysis can appraise both angular and intensity data of powder diffraction. In this work, X-ray diffraction pattern of Bi4(SiO4)3 was redetermined with intensity figure-of-merits, which qualify agreement between observed and calculated relative intensities. F30 is 158.90 (0.0059, 32), intensity figure of merit Rint is 8.7, I20(17), 8.0. The values of figure-of-merits show that the data of JCPDS cards are distorted. Both the experimental and calculated peak positions and heights are listed in detail.展开更多
The crystallization behaviour of the laser synthesized nanometric amorphous Si3N4 powders with the particle size of 15 nm in diameter has been studied between 1200° and 1700℃ by XRD,TEM and FTIR techniques. A sm...The crystallization behaviour of the laser synthesized nanometric amorphous Si3N4 powders with the particle size of 15 nm in diameter has been studied between 1200° and 1700℃ by XRD,TEM and FTIR techniques. A small amount of β-Si3N4 formed at 1250℃ and increased slowly until the α- β transformation happened at 1700℃, whereas α-Si3N4 appeared at 1300℃ andincreased rapidly between 1500-1600℃. The formation of β phase at the lower temperature was caused by the nitridation of free Si due to the preexisted β-nuclei in the Si3N4 particles, whereasthe α phase was formed by solid crystallization from the amorphous matrix. There were α and β SiC formed at 1700℃ due to the presence of Sio and Co gases in the system. FTIR analysis shows that two new IR absorption at 1356 and 1420 cm-1, and an overall strong absorption in wide wavenumber range resulted from the powders annealed at 1600 and 1700℃ respectively展开更多
High quality ultrafine Si powders have been synthesized from SiH4 by laser induced gas phase reaction. The powders prduced under different synthesis conditions have mean particle size of 10-120nm in diam. with narrow ...High quality ultrafine Si powders have been synthesized from SiH4 by laser induced gas phase reaction. The powders prduced under different synthesis conditions have mean particle size of 10-120nm in diam. with narrow particle size distribution, and free of hard agglomerates.The powders are polycrystalline with the ratio of mean grain to particle diameter being between 0.3-0.7. The size of the powder increases with increasing laser power and reaction pressure,but decreases with increasing silane gas flow rate and the addition of Ar diluent. Grain sizes drop distinctly with the rise of the addition of Ar gas and laser power, but change little with the gas flow rate and reaction temperature. The formation of Si particles under different synthesis conditions is discussed展开更多
This work aims at solving the problems of difficult dispersion,easy oxidation and high cost of nano carbon during application,carbon/magnesium aluminate spinel(C/MgAl_(2)O_(4))composite powders were prepared using MgC...This work aims at solving the problems of difficult dispersion,easy oxidation and high cost of nano carbon during application,carbon/magnesium aluminate spinel(C/MgAl_(2)O_(4))composite powders were prepared using MgC2O4·2H2O,MgO2,Al2O3 powder,and Al powder as raw materials by combustion synthesis.The results indicate that with the maximum MgC2O4·2H2O addition of 33.34 mass%,the prepared powder contains 1.17 mass%of carbon and carbon distributes among spinel grains.The MgAl_(2)O_(4)spinel shows both granular and rod-like morphologies.The granular MgAl_(2)O_(4)spinel is generated from mutual diffusion between MgO and Al2O3;while the rod-like MgAl_(2)O_(4)spinel is mainly formed by the vapor-solid growth mechanism from Mg vapor and Al2O3.展开更多
Direct LMD （laser metal deposition） was used to fabricate thin-wall Ti-6Al-4V using the powder mixture of Ti-6 wt.%Al-4 wt.%V. SEM （scanning electron microscopy）, OM （optical microscopy） and EDS （energy dispers...Direct LMD （laser metal deposition） was used to fabricate thin-wall Ti-6Al-4V using the powder mixture of Ti-6 wt.%Al-4 wt.%V. SEM （scanning electron microscopy）, OM （optical microscopy） and EDS （energy dispersive spectroscopy） were employed to examine the chemical composition and microstructure of the as-deposited sections. Vickers hardness tests were then applied to characterize the mechanical properties of the deposit samples which were fabricated using pre-mixed elemental powders. The EDS line scans indicated that the chemical composition of the samples was homogenous across the deposit. After significant analysis, some differences were observed among two sets of deposit samples which varied in the particle size of the mixing Ti-6wt.%Al-4wt.%V powder. It could be found that the set with similar particle number for Ti, Al and V powder made composition much more stable and could easily get industry qualified Ti-6Al-4V components.展开更多
基金This work was funded by Luoyang Major Science and Technology Innovation Project(2301009A)Henan Province Key ResearchandDevelopment Project(231111230200).
文摘Aiming at improving the properties of magnesia carbon materials,silicon aluminum carbide(Al_(4)SiC_(4))containing materials were prepared using industrial aluminum powder,silicon carbide powder,and graphite as raw materials,and activated alumina powder as an additive,mixing thoroughly,pressing into cylinders and then firing at 1200℃for 30 min in a carbon embedded atmosphere by the microwave method.The effects of the aluminum powder addition(20%and 24%,by mass)and activated alumina powder addition(0,3%,5%and 7%,by mass)on the microwave synthesis of Al_(4)SiC_(4) as well as the effect of the obtained Al_(4)SiC_(4) containing material on the properties of magnesia carbon bricks were studied.The results show that:compared with the samples with 20%aluminum powder,those with 24%aluminum powder generate more Al_(4)SiC_(4).With the activated alumina powder addition increasing from 0 to 7%,the amount of Al_(4)SiC_(4) generated increases first and then decreases.Compared with the sample without activated alumina powder,the samples with activated alumina powder show lower bulk density and higher apparent porosity.With the activated alumina powder addition increasing from 3%to 7%,the bulk density of the samples increases first and then decreases,while the apparent porosity of the samples shows an opposite trend.The optimal additions are 24%aluminum powder and 5%activated alumina powder,and Al_(4)SiC_(4) synthesized in this sample has a hexagonal plate structure.With the synthesized Al_(4)SiC_(4) containing material added,the magnesia carbon brick has slightly increased cold modulus of rupture,basically the same modulus of elasticity and improved oxidation resistance.
基金Project(2017YFB0305801)supported by the National Key R&D Program of ChinaProject(U1508213)supported by the Joint-Fund of NSFC-Liaoning,ChinaProject(51771051)supported by the National Natural Science Foundation of China.
文摘Ti-6 Al-4 V alloy powder was processed by electrode induction melting gas atomization(EIGA)at high gas pressure(5.5-7.0 MPa).The effects of atomizing gas pressure on the powder characteristics and the microstructure,along with the mechanical properties of the as-fabricated block by laser melting deposition(LMD),were investigated.The results indicate that the diameters of powders are distributed in a wide range of sizes from 1 to 400μm,and the median powder size(d50)decreases with increasing gas pressure.The powders with a size fraction of 100-150μm obtained at gas pressures of 6.0 and 6.5 MPa have better flowability.The oxygen content is consistent with the change trend of gas pressure within a low range of 0.06%-0.20%.Specimens fabricated by LMD are mainly composed ofα+βgrains with a fine lamellar Widmanstatten structures and have the ultimate tensile strength(UTS)and yield strength of approximately 1100 and 1000 MPa,respectively.Furthermore,the atomized powders have a favorable 3 D printing capability,and the mechanical properties of Ti-6 Al-4 V alloys manufactured by LMD typically exceed those of their cast or wrought counterparts.
基金Tabriz Branch,Islamic Azad University for the financial support of this research,which is based on a research project contract
文摘This work aimed to fabricate B4C reinforced aluminum matrix composites via blended powder semisolid forming that is an implementation of the benefits of semisolid forming to the powder metallurgy. Al7075 elements were incrementally added to ethanol solution under mechanical mixing. Al7075 constituents and B4C particles were blended in a high energy ball mill. Cold compacted Al7075/B4C blends were pressed at semisolid state. The effects of the size of the matrix（20, 45 and 63 μm）, reinforcing volume fraction（5%, 10% and 20%） and semisolid compaction pressure（50 and 100 MPa） on the morphology, microstructure, density, hardness, compression and bending strength were thoroughly analyzed. Experimental results revealed that the highest microstructural uniformity was achieved when large B4C particles（45 μm） were distributed within the small particles（20 μm） of the matrix phase. Composites with matrix particles larger than reinforcing phase indicated agglomerations in loadings more than 10%（volume fraction）. Agglomerated regions resisted against penetration of the liquid phase to the pores and lowered the density and strength of these composites. Composites with 20 μm Al7075 and 20%（volume fraction） 45 μm B4C powder pressed under 100 MPa exhibited the highest values of hardness（HV 190） and compressive strength（336 MPa）.
基金the National Laboratory SEDEAM-National Council for Science and Technology (CONACYT)ECOS M15P01 for the financial support and the facilities to develop this study
文摘Ti6Al4V powders with three different particle size distributions(0–20, 20–45, and 45–75 μm) were used to evaluate the effect of the particle size distribution on the solid-state sintering and their mechanical properties. The sintering kinetics was determined by dilatometry at temperatures from 900 to 1260°C. The mechanical properties of the sintered samples were evaluated by microhardness and compression tests. The sintering kinetics indicated that the predominant mechanism depends on the relative density irrespective of the particle size used. The mechanical properties of the sintered samples are adversely affected by increasing pore volume fraction. The elastic Young's modulus and yield stress follow a power law function of the relative density. The fracture behavior after compression is linked to the neck size developed during sintering, exhibiting two different mechanisms of failure: interparticle neck breaking and intergranular cracking in samples with relative densities below and above of 90%, respectively. The main conclusion is that relative density is responsible for the kinetics, mechanical properties, and failure behavior of Ti6 Al4 V powders.
文摘Ammonium metatungstate and cobalt nitrate were mixed at the molecular level in distilled water and then spray-decomposed to CoWO_4/WO_3 nanocomposite powder.The particle morphology,crystalline size,forming course,chemical composition and phase structure of the powder were studied by SEM,TEM,DTA-TG,IR and XRD,respectively.Results show that the powder is homogeneous,spherical and nano-aggregated.
文摘The present study aims to fabricate and evaluate the mechanical properties and wear behavior of Mg metal matrix composite,reinforced by 0,1.5,3,5 and 10 vol.%B4C microparticles.Mg−B4C samples were fabricated at 450℃ and under different loading rates by using split Hopkinson bar(SHB),drop hammer(DH)and Instron(QS)at strain rates of 1600,800 and 0.008 s–1,respectively.The mechanical properties including microhardness,quasi-static and dynamic compressive strengths and wear behavior of samples were experimentally investigated.The results show that,the hardness of SHB and DH samples is obtained to be 20.2%and 5.7%higher than that of the QS sample,respectively.The wear rate and wear mass loss of Mg–10.0%B4C samples fabricated by SHB were determined lower than those of the QS sample by nearly 33%and 39%,respectively.The quasi-static compressive strengths of Mg−5.0%B4C are improved by 39%,30%and 29%for the SHB,DH and QS samples,respectively,in comparison with the case of pure Mg.Furthermore,it is discovered that the dynamic compressive strength of samples is 51%−110%higher than their quasi-static value with respect to the B4C content.
文摘The effect of plasma arc powder surfacing process on the amount of B4C particles in the coating and the thermal behavior of B4C particles in different surfacing stages has been investigated.The results showed that the feeding rate of B4C partiles is the most important factor affecting the amount of B4C particles in the surfacing coating among all the surfacing parameters,and the most part of B4C Particles in the coating is nto the remainders of original solid B4C particles,but the consolidation products of the unmelted liquid B4C globules in the pool.The results also showed that the B4C particles would not be melted in the plasma arc column, their melting process mainly takes place in the anode spot region on the surface of the pool when surfacing current is less than 200A.
文摘Taking Ti6Al4V titanium alloy powder as the research object,on the basis of single layer scanning and single channel scanning experiment,this paper studies the influence of selective laser melting(SLM)process parameters on Ti6Al4V alloy material formability,and block forming experiment is carried out.Through the design of orthogonal experiment,morphology observation of sample and density analysis,results show that the best block molding parameters of SLM technology in Ti6Al4V alloy powder are laser power of 400 W,lap rate of 1 and the scanning speed of 750 mm/min,density can up to 96.17%.
基金supported by the project of Synthesis of Iron Oxide Red from Waste Acid(No.2016GIF-0035)
文摘Spent pickling liquors pose a serious environmental problem in most industrialized countries, mainly owing to their corrosive properties and their ferrous iron and hydrochloric acid content. In this paper, spent pickling liquor was used as an inexpensive raw material to prepare Fe304 magnetic powder via an oxidation method. Being able to recover the dissolved iron from spent pickling liquors would not only salvage a valuable material but also render the effluent environmentally benign. The structure of the Fe_3O_4 magnetic powder was characterized by X-ray diffraction. The morphology and size were characterized by scanning electron microscopy and transmission electron microscopy. Their magnetic properties were tested at room temperature by a vibrating sample magnetometer. In addition, the saturation magnetization of Fe_3 O_4 products can be further enhanced to 96.1 emu/g after purification.
基金the National Natural Science Foundation of China(No.51675029).
文摘The Ti−6Al−4V(TC4)alloy powder and forged solid were diffusion bonded by hot isostatic pressing(HIP)to fabricate a powder−solid part.The microstructure of the powder−solid part was observed by scanning electron microscope(SEM).The microhardness and tensile tests were conducted to investigate the mechanical properties.The results showed that the powder compact was near-fully dense,and the powder/solid interface was tight and complete.The microhardness of the interface was higher than that of the powder compact and solid.The fractures of all powder−solid tensile specimens were on the solid side rather than at the interface,which indicated that a good interfacial strength was obtained.The tensile strength and elongation of the powder compact were higher than those of the solid.It is concluded that the HIP process can successfully fabricate high-quality Ti−6Al−4V powder−solid parts,which provides a novel near net shape technology for titanium alloys.
文摘SiCf/Ti-6Al-4V composites were fabricated by the powder-coated fiber method. The precursor fiber was prepared under the optimized parameter, and the composites were made using the vacuum hot pressure method. The influence of heat exposure time on products of thelinterfacial reaction was investigated using scanning electron microscope （SEM） and analytical transmission electron microscope （TEM） with energy dispersive spectrometer （EDS）. The main products are TiC and Ti5Si3 after vacuum exposing the samples at 700℃ for 50 h. The growth dynamics of interracial reaction products was analyzed quantitatively, which fitted the parabola rule. The activity energy of the reaction was 252 kJ·mol^-1.
文摘In this paper, Pyrolysis Gas Chromatography Mass Spectroscopy is adopted to measure heating release curve of Si 3N 4 ultrafine powder at different temperatures. The results demonstrate that Si 3N 4 mainly adsorbs O 2, N 2, CO 2, NH 3 and H 2O during the storage at room temperature, of which O 2 and N 2 are physisorped and H 2O chemisorped. Hydrolysis reaction is the reason for oxygen increasement and the different states of oxygen can be determined by improved heat extraction. The mechanisms of the reaction speed as well as the formation of different states of oxygen are also discussed.
文摘In cooperation with figure-of-merits the Rietveld analysis can appraise both angular and intensity data of powder diffraction. In this work, X-ray diffraction pattern of Bi4(SiO4)3 was redetermined with intensity figure-of-merits, which qualify agreement between observed and calculated relative intensities. F30 is 158.90 (0.0059, 32), intensity figure of merit Rint is 8.7, I20(17), 8.0. The values of figure-of-merits show that the data of JCPDS cards are distorted. Both the experimental and calculated peak positions and heights are listed in detail.
文摘The crystallization behaviour of the laser synthesized nanometric amorphous Si3N4 powders with the particle size of 15 nm in diameter has been studied between 1200° and 1700℃ by XRD,TEM and FTIR techniques. A small amount of β-Si3N4 formed at 1250℃ and increased slowly until the α- β transformation happened at 1700℃, whereas α-Si3N4 appeared at 1300℃ andincreased rapidly between 1500-1600℃. The formation of β phase at the lower temperature was caused by the nitridation of free Si due to the preexisted β-nuclei in the Si3N4 particles, whereasthe α phase was formed by solid crystallization from the amorphous matrix. There were α and β SiC formed at 1700℃ due to the presence of Sio and Co gases in the system. FTIR analysis shows that two new IR absorption at 1356 and 1420 cm-1, and an overall strong absorption in wide wavenumber range resulted from the powders annealed at 1600 and 1700℃ respectively
文摘High quality ultrafine Si powders have been synthesized from SiH4 by laser induced gas phase reaction. The powders prduced under different synthesis conditions have mean particle size of 10-120nm in diam. with narrow particle size distribution, and free of hard agglomerates.The powders are polycrystalline with the ratio of mean grain to particle diameter being between 0.3-0.7. The size of the powder increases with increasing laser power and reaction pressure,but decreases with increasing silane gas flow rate and the addition of Ar diluent. Grain sizes drop distinctly with the rise of the addition of Ar gas and laser power, but change little with the gas flow rate and reaction temperature. The formation of Si particles under different synthesis conditions is discussed
文摘This work aims at solving the problems of difficult dispersion,easy oxidation and high cost of nano carbon during application,carbon/magnesium aluminate spinel(C/MgAl_(2)O_(4))composite powders were prepared using MgC2O4·2H2O,MgO2,Al2O3 powder,and Al powder as raw materials by combustion synthesis.The results indicate that with the maximum MgC2O4·2H2O addition of 33.34 mass%,the prepared powder contains 1.17 mass%of carbon and carbon distributes among spinel grains.The MgAl_(2)O_(4)spinel shows both granular and rod-like morphologies.The granular MgAl_(2)O_(4)spinel is generated from mutual diffusion between MgO and Al2O3;while the rod-like MgAl_(2)O_(4)spinel is mainly formed by the vapor-solid growth mechanism from Mg vapor and Al2O3.
文摘Direct LMD （laser metal deposition） was used to fabricate thin-wall Ti-6Al-4V using the powder mixture of Ti-6 wt.%Al-4 wt.%V. SEM （scanning electron microscopy）, OM （optical microscopy） and EDS （energy dispersive spectroscopy） were employed to examine the chemical composition and microstructure of the as-deposited sections. Vickers hardness tests were then applied to characterize the mechanical properties of the deposit samples which were fabricated using pre-mixed elemental powders. The EDS line scans indicated that the chemical composition of the samples was homogenous across the deposit. After significant analysis, some differences were observed among two sets of deposit samples which varied in the particle size of the mixing Ti-6wt.%Al-4wt.%V powder. It could be found that the set with similar particle number for Ti, Al and V powder made composition much more stable and could easily get industry qualified Ti-6Al-4V components.
