Fluoride rubber F2311 film, an alternating copolymer of CF2-CFC1 （CTFE） and CH2-CF2 （VF2） components, was treated by atmospheric pressure dielectric barrier discharge （DBD） in air. The surface structure, topogra...Fluoride rubber F2311 film, an alternating copolymer of CF2-CFC1 （CTFE） and CH2-CF2 （VF2） components, was treated by atmospheric pressure dielectric barrier discharge （DBD） in air. The surface structure, topography and surface chemistry of the treated F2311 films were characterized by contact angle measurement, atomic force microscopy （AFM）, and X-ray photoelectron spectroscopy （XPS）, respectively. The experimental results showed that a short time air plasma treatment led to morphological, wettability and chemical changes in the F2311 films. The surface hydrophilicity increased greatly after the plasma treatment, the static water contact angle decreased from 98.6° to 32°, and oxygen containing groups （C=O, O-C=O, etc. ） were introduced. Atomic force microscopy revealed that plasma produced by DBD etched F2311 films obviously. The roughness of the samples increased remarkably with the formation of peaks and valleys on the treated surfaces. The increased surface wettability may be correlated with both the introduction of hydrophilic groups due to air plasma oxidation of the surface and the change in surface morphology etched by DBD.展开更多
This study reports the development and performance of a pilot-scale barrel atmospheric plasma reactor for the atmospheric plasma activation treatment of polymer particles. The polymer particles treated included acrylo...This study reports the development and performance of a pilot-scale barrel atmospheric plasma reactor for the atmospheric plasma activation treatment of polymer particles. The polymer particles treated included acrylonitrile butadiene styrene(ABS) and polypropylene(PP). These particles had diameters in the range of 3–5 mm. The initial studies were carried out using a laboratory-scale barrel reactor designed to treat polymer particle batch sizes of 20 g. A pilot-scale reactor that could treat 500 g particle batch sizes was then developed to facilitate pre-industrial-scale treatments. The effect of operating pulse density modulation(PDM) in the range 10%–100% and plasma treatment time on the level of activation of the treated polymers were then investigated. ABS revealed a larger decrease in water contact angle compared with PP after plasma treatment under the same conditions. The optimal treatment time of ABS(400 g of polymer particles) in the pilot-scale reactor was 15 min. The plasma-activated polymer particles were used to fabricate dog-bone polymer parts through injection molding.Mechanical testing of the resulting dog-bone polymer parts revealed a 10.5% increase in tensile strength compared with those fabricated using non-activated polymer particles.展开更多
基金the Joint Foundation of the Council of National Natural Science Foundation of China(NSFC)China Academy of Engineering Physics(CAEP)the National Natural Science Foundation of China(NSAF United Foundation)
文摘Fluoride rubber F2311 film, an alternating copolymer of CF2-CFC1 （CTFE） and CH2-CF2 （VF2） components, was treated by atmospheric pressure dielectric barrier discharge （DBD） in air. The surface structure, topography and surface chemistry of the treated F2311 films were characterized by contact angle measurement, atomic force microscopy （AFM）, and X-ray photoelectron spectroscopy （XPS）, respectively. The experimental results showed that a short time air plasma treatment led to morphological, wettability and chemical changes in the F2311 films. The surface hydrophilicity increased greatly after the plasma treatment, the static water contact angle decreased from 98.6° to 32°, and oxygen containing groups （C=O, O-C=O, etc. ） were introduced. Atomic force microscopy revealed that plasma produced by DBD etched F2311 films obviously. The roughness of the samples increased remarkably with the formation of peaks and valleys on the treated surfaces. The increased surface wettability may be correlated with both the introduction of hydrophilic groups due to air plasma oxidation of the surface and the change in surface morphology etched by DBD.
基金support of the Enterprise Ireland Innovation Partnership programthe SFI funded Ⅰ-Form Advanced Manufacturing Research Centre 16/RC/3872
文摘This study reports the development and performance of a pilot-scale barrel atmospheric plasma reactor for the atmospheric plasma activation treatment of polymer particles. The polymer particles treated included acrylonitrile butadiene styrene(ABS) and polypropylene(PP). These particles had diameters in the range of 3–5 mm. The initial studies were carried out using a laboratory-scale barrel reactor designed to treat polymer particle batch sizes of 20 g. A pilot-scale reactor that could treat 500 g particle batch sizes was then developed to facilitate pre-industrial-scale treatments. The effect of operating pulse density modulation(PDM) in the range 10%–100% and plasma treatment time on the level of activation of the treated polymers were then investigated. ABS revealed a larger decrease in water contact angle compared with PP after plasma treatment under the same conditions. The optimal treatment time of ABS(400 g of polymer particles) in the pilot-scale reactor was 15 min. The plasma-activated polymer particles were used to fabricate dog-bone polymer parts through injection molding.Mechanical testing of the resulting dog-bone polymer parts revealed a 10.5% increase in tensile strength compared with those fabricated using non-activated polymer particles.
