The correction for antenna phase center is considered in processing Global Positioning System （GPS） data collected from a network of GPS ultra-short baselines. Compared with the leveling measurements, the GPS result...The correction for antenna phase center is considered in processing Global Positioning System （GPS） data collected from a network of GPS ultra-short baselines. Compared with the leveling measurements, the GPS results show that the relative vertical offsets for the pairs of GPS receiver antenna phase centers still exist, although absolute calibration of the antenna phase center variations （PCVs） has been considered. With respect to the TPS CR.G3 antenna, the relative vertical offset for the LEI AT504 antenna is 8.4 mm, the offset for the ASH701945C_M antenna is 5.5 mm, and those for the ASHY00936E_C and ASH701945B_M antennas are approximately between 2 mm and -3 mm. The relative offsets for the same type of antennas are approximately 1 mm. By correcting the absolute PCVs, the existing relative offset becomes negligible for horizontal positioning.展开更多
With regard to the inferior techniques and low accuracy of phase center calibration of an antenna array, this paper proposes a new calibration method considering the actual antenna pointing by introducing a precise en...With regard to the inferior techniques and low accuracy of phase center calibration of an antenna array, this paper proposes a new calibration method considering the actual antenna pointing by introducing a precise engineering surveying technique to measure the real state of antennas. First, an industrial photogrammetric system is utilized to obtain the coordinates of points on antenna panels in different postures, and the actual pointing of the mechanical axis is obtained via least-squares fitting. Then, based on this, the coordinates of antenna rotation center are obtained by seeking the intersection of mechanical axes via using the matrix method. Finally, the mechanical axis in arbitrary postures is estimated based on the inverse-angle weighting interpolation method, and the reliable phase center is obtained by moving a fixed length from the projective center along the mechanical axis. An uplink antenna array including three ? 3 m antennas is taken as experimental object, and all photogrammetric coordinate systems are unified by the engineering control network, with each antenna phase center precisely calibrated via the proposed method. The results of electrical signal synthesis indicate that this method can effectively overcome the influence of gravity deformation and mechanical installation error, and enhance the synthetic signal magnitude of the uplink antenna array.展开更多
基金supported by the Science for Earthquake Resilience(XH14070Y,XH15064Y)the China NationalSpecial Fund for Earthquake Scientific Research in Public Interest(201208009)
文摘The correction for antenna phase center is considered in processing Global Positioning System （GPS） data collected from a network of GPS ultra-short baselines. Compared with the leveling measurements, the GPS results show that the relative vertical offsets for the pairs of GPS receiver antenna phase centers still exist, although absolute calibration of the antenna phase center variations （PCVs） has been considered. With respect to the TPS CR.G3 antenna, the relative vertical offset for the LEI AT504 antenna is 8.4 mm, the offset for the ASH701945C_M antenna is 5.5 mm, and those for the ASHY00936E_C and ASH701945B_M antennas are approximately between 2 mm and -3 mm. The relative offsets for the same type of antennas are approximately 1 mm. By correcting the absolute PCVs, the existing relative offset becomes negligible for horizontal positioning.
文摘With regard to the inferior techniques and low accuracy of phase center calibration of an antenna array, this paper proposes a new calibration method considering the actual antenna pointing by introducing a precise engineering surveying technique to measure the real state of antennas. First, an industrial photogrammetric system is utilized to obtain the coordinates of points on antenna panels in different postures, and the actual pointing of the mechanical axis is obtained via least-squares fitting. Then, based on this, the coordinates of antenna rotation center are obtained by seeking the intersection of mechanical axes via using the matrix method. Finally, the mechanical axis in arbitrary postures is estimated based on the inverse-angle weighting interpolation method, and the reliable phase center is obtained by moving a fixed length from the projective center along the mechanical axis. An uplink antenna array including three ? 3 m antennas is taken as experimental object, and all photogrammetric coordinate systems are unified by the engineering control network, with each antenna phase center precisely calibrated via the proposed method. The results of electrical signal synthesis indicate that this method can effectively overcome the influence of gravity deformation and mechanical installation error, and enhance the synthetic signal magnitude of the uplink antenna array.
