Seismic effectiveness evaluation and optimized design of tie up method for securing museum collections

To quantify the seismic effectiveness of the most commonly used fishing line tie up method for securing museum collections and optimize fixed strategies for exhibitions,shaking table tests of the seismic systems used for typical museum collection replicas have been carried out.The influence of body shape and fixed measure parameters on the seismic responses of replicas and the interaction behavior between replicas and fixed measures have been explored.Based on the results,seismic effectiveness evaluation indexes of the tie up method are proposed.Reasonable suggestions for fixed strategies are given,which provide a basis for the exhibition of delicate museum collections considering the principle of minimizing seismic responses and intervention.The analysis results show that a larger ratio of height of mass center to bottom diameter led to more intense rocking responses.Increasing the initial pretension of fishing lines was conducive to reducing the seismic responses and stress variation of the lines.Through comprehensive consideration of the interaction forces and effective securement,it is recommended to apply 20%of breaking stress as the initial pretension.For specific museum collections that cannot be effectively protected by the independent tie up method,an optimized strategy of a combination of fishing lines and fasteners is recommended.

Seismic Design Strategy of High Pier Bridge

China’s infrastructure construction has been continuously improving in recent years,especially its highway construction,which spans from north to south and connects east to west.Some special areas are also interconnected through bridges,but constructing highway bridges through complex terrains or across valleys and mountain gullies presents significant challenges,requiring an increase in the height of bridge piers.These bridge piers generally reach tens or even hundreds of meters in height.Furthermore,the construction of these high-pier bridges is becoming increasingly widespread.Not only do they pose greater construction challenges,but they also have higher requirements for seismic resistance.This article primarily analyzes the characteristics of high-pier bridges and proposes seismic design schemes,calculation methods,and design strategies to enhance the construction quality of high-pier bridges.

The Ultimate Anti-Seismic Design Method

The design mechanisms and methods of the invention are intended to minimize problems related to the safety of structures in the event of natural phenomena such as earthquakes, tornadoes, and strong winds. It is achieved by controlling the deformations of the structure. Damage and deformation are closely related concepts since the control of deformations also controls the damage. The design method of applying artificial compression to the ends of all longitudinal reinforced concrete walls and, at the same time, connecting the ends of the walls to the ground using ground anchors placed at the depths of the boreholes, transfers the inertial stresses of the structure in the ground, which reacts as an external force in the structure’s response to seismic displacements. The wall with the artificial compression acquires dynamic, larger active cross-section and high axial and torsional stiffness, preventing all failures caused by inelastic deformation. By connecting the ends of all walls to the ground, we control the eigenfrequency of the structure and the ground during each seismic loading cycle, preventing inelastic displacements. At the same time, we ensure the strong bearing capacity of the foundation soil and the structure. By designing the walls correctly and placing them in proper locations, we prevent the torsional flexural buckling that occurs in asymmetrical floor plans, and metal and tall structures. Compression of the wall sections at the ends and their anchoring to the ground mitigates the transfer of deformations to the connection nodes, strengthens the wall section in terms of base shear force and shear stress of the sections, and increases the strength of the cross-sections to the tensile at the ends of the walls by introducing counteractive forces. The use of tendons within the ducts prevents longitudinal shear in the overlay concrete, while anchoring the walls to the foundation not only dissipates inertial forces to the ground but also prevents rotation of the walls, thus maintaining the structural integrity of the beams. The prestressing at the bilateral ends of the walls restores the structure to its original position even inelastic displacements by closing the opening of the developing cracks.

Inelastic displacement ratio of low-to mid-rise BRBFs designed under variable levels of seismicity

Buckling-restrained braces(BRBs)have shown their capability to provide building structures with stiffness,strength,and ductility.Estimating the seismic drifts of buckling-restrained braced frames(BRBFs)is an important design step to control structural and non-structural damage.In current practice of seismic design,the estimation of seismic drifts of BRBFs is performed by using empirical calculations that are independent upon either the type of the structural system or the design level of seismicity.In these empirical calculations,the seismic drifts are estimated by amplifying the reduced elastic drifts obtained under design lateral loading with a displacement amplification factor(DAF).The value of DAF is considered equal to the product of the response modification factor R and the inelastic displacement ratioρ.The goal of the current research is to assess the value ofρfor low-to mid-rise BRBFs designed under low and high levels of seismicity.This goal has been achieved by conducting a series of elastic and inelastic time-history analyses pertaining to an ensemble of earthquake records on 3-,6-and 9-story BRBFs.The results indicate that theρ-ratio increases with an increase in design seismic intensity and an increase in experienced inelasticity.The range ofρfor low seismicity designs ranges from 0.63 to 0.9,while for high seismicity designs this range stretches from 0.83 to 1.29.It has been found that the consideration of a generalρ-ratio of 1.0 is a reasonable estimation for the design of the BRBFs considered in this study.

Optimal design for rubber concrete layered periodic foundations based on the analytical approximations of band gaps and mapping relations

The seismic performance of rubber concrete-layered periodic foundations are significantly influenced by their design,in which the band gaps play a paramount role.Aiming at providing better designs for these foundations,this study first proposes and validates the analytical formulas to approximate the bounds of the first few band gaps.In addition,the mapping relations linking the frequencies of different band gaps are presented.Furthermore,an optimal design method for these foundations is developed,which is validated through an engineering example.It is demonstrated that ensuring the superstructure’s resonance zones are completely covered by the corresponding periodic foundation’s band gaps can achieve satisfactory vibration attenuation effects,which is a good strategy for the design of rubber concrete layered periodic foundations.

FEMA P695-Quantification of Building Seismic Performance Factors简介

目前,各国建筑抗震设计规范对结构在"大震"下倒塌概率的评估尚不完善。FEMA P695以美国现行规范为基础,提出了一套用于标定其建筑抗震设计规范中关键设计参数的方法,用以保证结构在"大震"下的倒塌概率不超过某一可接受的值。介绍了美国建筑抗震设计规范的理论基础,说明了FEMA P695中关键参数的定义与美国现行抗震规范中设计参数的关系,详细介绍了该方法的基本内容、方法流程、关键细节、理论思路等,为了解美国抗震规范的发展方向及水平提供了参考。

Damage investigation of girder bridges under the Wenchuan earthquake and corresponding seismic design recommendations

An investigation of girder bridges on National Highway 213 and the Doujiangyan-Wenchuan expressway after the Wenchuan earthquake showed that typical types of damage included： span collapses due to unseating at expansion joints; shear key failure; and damage of the expansion joint due to the slide-induced large relative displacement between the bottom of the girder and the top of the laminated-rubber bearing. This slide, however, can actually act as a form of isolation for the substructure, and as a result, the piers and foundation of most of the bridges on state route 213 suffered minor damage. The exception was the Baihua Bridge, which suffered severe damage. Corresponding seismic design recommendations are presented based on this investigation.

Lessons learned from the “5.12” Wenchuan Earthquake:evaluation of earthquake performance objectives and the importance of seismic conceptual design principles

Many different types of buildings were severely damaged or collapsed during the May 12, 2008 Great Wenchuan Earthquake. Based on survey data collected in regions that were subjected to moderate to severe earthquake intensities, a comparison between the observed building damage, and the three earthquake performance objectives and seismic conceptual design principles specified by the national ＂Code for Seismic Design of Buildings GB50011-2001,＂ was carried out. Actual damage and predicted damage for a given earthquake level for different types of structures is compared. Discussions on seismic conceptual design principles, with respect to multiple defense lines, strong column-weak beam, link beam of shear walls, ductility detailing of masonry structures, exits and staircases, and nonstructural elements, etc. are carried out. Suggestions for improving the seismic design of structures are also proposed. It is concluded that the seismic performance objectives for three earthquake levels, i.e., ＂no failure under minor earthquake level, ＂＂repairable damage under moderate earthquake level＂ and ＂no collapse under major earthquake level＂ can be achieved if seismic design principles are carried out by strictly following the code requirements and ensuring construction quality.

Seismic fragility assessment of RC frame structure designed according to modern Chinese code for seismic design of buildings

Following several damaging earthquakes in China, research has been devoted to find the causes of the collapse of reinforced concrete （RC） building sand studying the vulnerability of existing buildings. The Chinese Code for Seismic Design of Buildings （CCSDB） has evolved over time, however, there is still reported earthquake induced damage of newly designed RC buildings. Thus, to investigate modern Chinese seismic design code, three low-, mid- and high-rise RC frames were designed according to the 2010 CCSDB and the corresponding vulnerability curves were derived by computing a probabilistic seismic demand model （PSDM）.The PSDM was computed by carrying out nonlinear time history analysis using thirty ground motions obtained from the Pacific Earthquake Engineering Research Center. Finally, the PSDM was used to generate fragility curves for immediate occupancy, significant damage, and collapse prevention damage levels. Results of the vulnerability assessment indicate that the seismic demands on the three different frames designed according to the 2010 CCSDB meet the seismic requirements and are almost in the same safety level.

Performance-based seismic design of nonstructural building components:The next frontier of earthquake engineering

With the development and implementation of performance-based earthquake engineering,harmonization of performance levels between structural and nonstructural components becomes vital. Even if the structural components of a building achieve a continuous or immediate occupancy performance level after a seismic event,failure of architectural,mechanical or electrical components can lower the performance level of the entire building system. This reduction in performance caused by the vulnerability of nonstructural components has been observed during recent earthquakes worldwide. Moreover,nonstructural damage has limited the functionality of critical facilities,such as hospitals,following major seismic events. The investment in nonstructural components and building contents is far greater than that of structural components and framing. Therefore,it is not surprising that in many past earthquakes,losses from damage to nonstructural components have exceeded losses from structural damage. Furthermore,the failure of nonstructural components can become a safety hazard or can hamper the safe movement of occupants evacuating buildings,or of rescue workers entering buildings. In comparison to structural components and systems,there is relatively limited information on the seismic design of nonstructural components. Basic research work in this area has been sparse,and the available codes and guidelines are usually,for the most part,based on past experiences,engineering judgment and intuition,rather than on objective experimental and analytical results. Often,design engineers are forced to start almost from square one after each earthquake event: to observe what went wrong and to try to prevent repetitions. This is a consequence of the empirical nature of current seismic regulations and guidelines for nonstructural components. This review paper summarizes current knowledge on the seismic design and analysis of nonstructural building components,identifying major knowledge gaps that will need to be filled by future research. Furthermore,considering recent trends in earthquake engineering,the paper explores how performance-based seismic design might be conceived for nonstructural components,drawing on recent developments made in the field of seismic design and hinting at the specific considerations required for nonstructural components.

Ground support design for dynamic loading conditions:A quantitative data-driven approach based on rockburst case studies

There are considerable challenges associated with the design of ground support for seismically-active underground mines.It is extremely difficult to establish the demand on ground support as well as the capacity of a ground support system.The resulting dynamic or impact loads caused by mining-induced seismicity are difficult to anticipate and quantify.The performance of a ground support system is defined by the load distribution and interaction between several reinforcement and surface support elements.Consequently,the design of ground support in seismically-active mines tends to evolve,or be modified based on qualitative assessments of perceived performance or response to significant seismic events or rockbursts.This research is motivated by a need to provide quantitative and data-driven design guidelines for ground support systems subjected to dynamic-loading conditions.Rockburst data were collected from three deep and seismically-active underground mines in the Sudbury basin in Canada.The constructed database comprises 209 seismic events that resulted in damage to mine excavations and ground support.These events were associated with damage at 324 locations within the three mines.The developed ground support design strategy,based on these documented case studies,identifies areas where the use of dynamic or enhanced support should be employed.The developed design methodology provides guidelines for the zoning of mine locations in which installation of enhanced support is recommended,the specifications for an optimal ground support system,and the timing or sequence of installation.

Seismic design of Xiluodu ultra-high arch dam

The 285.5 m-high Xiluodu Arch Dam is located in a seismic region along the Jinsha River in China, where the horizontal components of peak ground accelerations for design and checking earthquakes have been estimated to be 0.355 g and 0.423 g, respectively( g is the gravitational acceleration). The ground motion parameters of design and checking earthquakes are defined by exceedance probabilities of 2% over 100 years and 1% over 100 years, respectively. The dam shape was first selected and optimized through static analysis of the basic load combinations, and then adjusted after taking into account the seismic loads. The dam should be operational during and after the design earthquake with or without minor repairs, and maintain local and global stabilities during an extreme earthquake. Both linear elastic dynamic analysis and nonlinear dynamic analysis considering radiation damping, contraction joints, and material nonlinearity were conducted to assess the stress in the arch dam.The dynamic analysis shows that the maximum dynamic compressive stresses are less than the allowable levels, while the area with tensile stress over the limit is less than 15% of the dam surface and the maximum contraction openings range from 10 mm to 25 mm. The arch dam has sufficient earthquake-resistance capacity and meets the safety requirements. Nevertheless, steel reinforcement has been provided at the dam toe and in the zones of high tensile stress on the dam surface out of extra precaution.

Highway bridge seismic design:summary of FHWA/MCEER project on seismic vulnerability of new highway construction

The Federal Highway Administration (FHWA) sponsored a large,multi-year project conducted by the Multidisciplinary Center for Earthquake Engineering Research (MCEER) titled'Seismic Vulnerability of New Highway Construction'(MCEER Project 112),which was completed in 1998.MCEER coordinated the work of many researchers,who performed studies on the seismic design and vulnerability analysis of highway bridges,tunnels,and retaining structures. Extensive research was conducted to provide revisions and improvements to current design and detailing approaches and national design specifications for highway bridges.The program included both analytical and experimental studies,and addressed seismic hazard exposure and ground motion input for the U.S.highway system;foundation design and soil behavior: structural importance,analysis,and response:structural design issues and details;and structural design criteria.

An improved pseudo-static method for seismic resistant design of underground structures

This paper describes a commonly used pseudo-static method in seismic resistant design of the cross section of underground structures. Based on dynamic theory and the vibration characteristics of underground structures, the sources of errors when using this method are analyzed. The traditional seismic motion loading approach is replaced by a method in which a one-dimensional soil layer response stress is differentiated and then converted into seismic live loads. To validate the improved method, a comparison of analytical results is conducted for internal forces under earthquake shaking of a typical shallow embedded box-shaped subway station structure using four methods： the response displacement method, finite element response acceleration method, the finite element dynamic analysis method and the improved pseudo-static calculation method. It is shown that the improved finite element pseudo-static method proposed in this paper provides an effective tool for the seismic design of underground structures. The evaluation yields results close to those obtained by the finite element dynamic analysis method, and shows that the improved finite element pseudo-static method provides a higher degree of precision.

Revision of seismic design codes corresponding to building damagesin the “5.12” Wenchuan earthquake

A large number of buildings were seriously damaged or collapsed in the "5.12" Wenchuan earthquake. Based on field surveys and studies of damage to different types of buildings, seismic design codes have been updated. This paper briefly summarizes some of the major revisions that have been incorporated into the "Standard for classification of seismic protection of building constructions GB50223-2008" and "Code for Seismic Design of Buildings GB50011-2001." The definition of seismic fortification class for buildings has been revisited, and as a result, the seismic classifications for schools, hospitals and other buildings that hold large populations such as evacuation shelters and information centers have been upgraded in the GB50223-2008 Code. The main aspects of the revised GB50011-2001 code include: (a) modification of the seismic intensity specified for the Provinces of Sichuan, Shanxi and Gansu; (b) basic conceptual design for retaining walls and building foundations in mountainous areas; (c) regularity of building configuration; (d) integration of masonry structures and precast RC floors; (e) requirements for calculating and detailing stair shafts; and (f) limiting the use of single-bay RC frame structures. Some significant examples of damage in the epicenter areas are provided as a reference in the discussion on the consequences of collapse, the importance of duplicate structural systems, and the integration of RC and masonry structures.

A Seismic Design Method for Subsea Pipelines Against Earthquake Fault Movement

As there are no specific guidelines on design of subsea pipelines crossing active seismic faults, methods for land buried pipelines have been applied to. Taking the large seismic fault movement into account, this paper proposes improved methods for seismic designs of subsea pipelines by comprehensively investigating the real constraining of soil on the pipelines, the interaction processes of soil with the pipeline, the plastic slippage of the soil, and the elastic-plastic properties of the pipeline materials. New formulas are given to calculate the length of transition section and its total elongation. These formulas are more reasonable in mechanism, and more practical for seismic design of subsea pipelines crossing active faults.

Comparison of seismic actions and structural design requirements in Chinese Code GB 50011 and International Standard ISO 3010

This papcr presents a comparison between the Chinese Code GB50011-2001 and the International Standard ISO3010:2001(E),emphasizing the similarities and differences related to design requirements,seismic actions and analytical approaches.Similarities include:earthquake return period,conceptual design,site classification,structural strength and ductility requirements,deformation limits,response spectra,seismic analysis procedures,isolation and energy dissipation, and nonstructural elements.Differences exist in the following areas:seismic levels,earthquake loading,mode damping factors and structural control.

Seismic design or retrofit of buildings with metallic structural fuses by the damage-reduction spectrum

Recently, the structural fuse has become an important issue in the field of earthquake engineering. Due to the trilinearity of the pushover curve of buildings with metallic structural fuses, the mechanism of the structural fuse is investigated through the ductility equation of a single-degree-of-freedom system, and the corresponding damage-reduction spectrum is proposed to design and retrofit buildings. Furthermore, the controlling parameters, the stiffness ratio between the main frame and structural fuse and the ductility factor of the main frame, are parametrically studied, and it is shown that the structural fuse concept can be achieved by specific combinations of the controlling parameters based on the proposed damage-reduction spectrum. Finally, a design example and a retrofit example, variations of real engineering projects after the 2008 Wenchuan earthquake, are provided to demonstrate the effectiveness of the proposed design procedures using buckling restrained braces as the structural fuses.

Acomparative study between China and U.S.on seismic design philosophy and practice of a long span arch bridge

This paper presents the first of a series of case studies on the seismic design of long span bridges （cable-stayed bridges, suspension bridges and arch bridges） under a cooperative research project on seismic behavior and design of highway bridges between the State Key Laboratory for Disaster Reduction in Civil Engineering, Tongji University and the Multidisciplinary Center for Earthquake Engineering Research, University at Buffalo. The objective of this series of case studies is to examine the differences and similarities on the seismic design practice of long span bridges in China and the U.S., to identify research needs and to develop design guidelines beneficial to bridge engineers in both countries. Unlike short to medium span bridges, long span bridges are not included in most seismic design specifications, mainly because they are location dependent and structurally unique. In this paper, an available model of a steel tied half through arch bridge with a main span of 550m in China is discussed. Analysis is focused on comparisons of the seismic responses due to different ground motions. Seismic design criteria and seismic performance requirements for long span bridges in both countries were first introduced and compared, and then three near field earthquake records with large vertical components were selected as the excitations to examine the seismic behavior and seismic vulnerability of the bridge. Results show that （1） the selected near field ground motions cause larger responses to key components （critical sections） of the bridge （such as arch rib ends） with a maximum increase of more than twice those caused by the site specific ground motions; （2） piers, longitudinal girders and arch crowns are more vulnerable to vertical motions, especially their axial forces; and （3） large vertical components of near field ground motions may not significantly affect the bridge＇s internal forces provided that their peak acceleration spectra ordinates only appear at periods of less than 0.2s. However, they may have more influence on the longitudinal displacements of sliding bearings due to their large displacement spectra ordinates at the fundamental period of the bridge.

Seismic performance analysis and design suggestion for frame buildings with cast-in-place staircases

Many staircases in reinforced concrete （RC） frame structures suffered severe damage during the Wenchuan earthquake. Elastic analyses for 18 RC structure models with and without staircases are conducted and compared to study the influence of the staircase on the stiffness, displacements and internal forces of the structures. To capture the yielding development and damage mechanism of frame structures, elasto-plastic analysis is carried out for one of the 18 models. Based on the features observed in the analyses, a new type of staircase design i.e., isolating them from the master structure to eliminate the effect of K-type struts, is proposed and discussed. It is concluded that the proposed method of staircase isolation is effective and feasible for engineering design, and does not significantly increase the construction cost.