Revealing the potential of apparent critical current density of Li/garnet interface with capacity perturbation strategy

Apparent critical current density(j_(Ac)^(a))of garnet all-solid-state lithium metal symmetric cells(ASSLSCs)is a fundamental parameter for designing all-solid-state lithium metal batteries.Nevertheless,how much the possible maximum apparent current density that a given ASSLSC system can endure and how to reveal this potential still require study.Herein,a capacity perturbation strategy aiming to better measure the possible maximum j_(Ac)^(a)is proposed for the first time.With garnet-based plane-surface structure ASSLSCs as an exemplification,the j_(Ac)^(a)is quite small when the capacity is dramatically large.Under a perturbed capacity of 0.001 mA h cm^(-2),the j_(Ac)^(a)is determined to be as high as 2.35 mA cm^(-2)at room temperature.This investigation demonstrates that the capacity perturbation strategy is a feasible strategy for measuring the possible maximum j_(Ac)^(a)of Li/solid electrolyte interface,and hopefully provides good references to explore the critical current density of other types of electrochemical systems.

Wavelet analysis and interpretation of gravity data in Sichuan-Yunnan region, China

The Bouguer gravity anomaly data of Sichuan-Yunnan region and its vicinity were analyzed with wavelet trans- formation method. In the process, complete orthogonal wavelet function system with good symmetry and higher vanishing moment was selected to decompose the gravity anomaly into two parts. With the power spectral analysis on the decomposed anomalies, we interpreted that the two parts of anomalies represent the density variation in upper and middle crust, and in deep crust and uppermost mantle, respectively. The two parts of anomalies indicate the difference between shallow and deep tectonics. The results of shallow-layer apparent density mapping reveal that: a) the crustal density in Sichuan basin is higher than that in Songpan-Garze orogenic zone; b) the density of Kangdian rhombic block is heterogeneous; c) the boundary faults of Kangdian block are of different density fea- tures, suggesting different tectonic signification. The results of deep-layer apparent density mapping show a similar, but not the same, density distribution pattern as the shallow results, and indicate that the tectonics of shallow and deep crust are different, they may be in a status of incomplete coupling. Our results also show that the earthquakes in this area are controlled not only by the fracture zones but also by the deep density distribution.

Comparison of effective parameters for copper powder production via electrorefining and electrowinning cells and improvement using DOE methods

The influences of cupric ion concentration （5-35 g/L）,current density （500-2000 A/m2）,circulation rate of the electrolyte solution （15-120 mL/min）,and temperature （25-60℃） on the physical and chemical properties of copper powders obtained in electrolysis cells were investigated.Two industrial processes,electrorefining （ER） cells with a synthetic electrolyte and electrowinning （EW） cells with an original solution of coppermineral leaching,were utilized to produce copper powders.Finally,the statistical full factorial method of design of experiments （DOE） was employed to investigate the interaction or the main effects of processes.The results show that increasing the copper concentration and temperature can increase the grain size,apparent density,and electrical energy consumption.On the other hand,increasing the current density and circulation rate of the electrolyte can decrease them.This production process is optimized via DOE to control the interactive and main effects to produce copper powders with favorable properties.

Analysis of synthetic parameters for coating aluminum powders with phenyltriethoxysilane coupling agent and their effects on powder flow behavior

Though silanization of aluminum powder is currently used to improve its flow properties,for use as an alternative fuel source,there are a wide range of experimental parameters for the process and not all of them have been thoroughly explored.Until this is complete,it is unknown if the process is optimized in terms of time,efficiency,and effect.Herein,we report on a study into the effects of changes in humidity,degree of agitation,reaction temperature,and curing time upon the deposition of phenyl triethoxysilane into 20μm(d50)aluminum particles.We confirm the deposition of the coating via diffuse reflectance infrared spectroscopy and x-ray photoelectron spectroscopy.We then characterize the coated particles using apparent density measurements and Carney flow methods.Using analysis of variance,we find that,of the parameters explored,only changes in cure time and reaction temperature provide meaningful changes to the apparent density,while none of our parameters produced statistically significant changes in Carney flow values.Thus,we conclude that,when optimizing silanization of aluminum particles,environmental control of humidity is unneeded and that the reaction can be run with minimal agitation.The ability to largely ignore these parameters is a benefit to large-scale processing.

Characterization of nanoparticle mixed 316L powder for additive manufacturing

Nanoparticles reinforced steels have many advantaged mechanical properties.Additive manufacturing offers a new method for fabricating nanoparticles reinforced high performance metal components.In this work,we report the application of low energy ball milling in mixing nanoparticles and micron 316 L powder.With this method,0.3 and 1.0 wt% Y2 O3 nanoparticles can be uniformly distributed on the surface of 316 L powder with the parameters of ball-to-powder ratio at 1:1,speed at 90 rpm and 7 h of mixing.The matrix 316 L powders remain spherical in shape after the mixing process.In the meantime,the effect of low energy ball milling and the addition of Y2 O3 nanoparticles on the powder characteristics(flowability,apparent density and tap density) are also studied.Results show that the process of low energy ball milling itself can slightly decrease the flowability and apparent density of the 316 L powder.The addition of 0.3 and 1.0 wt% Y2 O3 nanoparticles can also decrease the flowability,the tap density and the apparent density compared with the original 316 L powder.All of these changes result from the rough surface of the mixed powder produced by ball milling and the addition of Y2 O3 nanoparticles.The powder’s rough surface can increase the coefficient of friction of powders.The mixture of 316 L powder and Y2 O3 nanoparticles can be successfully used for selective laser melting(SLM).The relative density of SLM 316 L-Y2 O3 is measured at 99.5%.However,Y2 O3 agglomerations were observed which is due to the poor wettability between 316 L and Y2 O3.