Highly Thermoconductive,Strong Graphene‑Based Composite Films by Eliminating Nanosheets Wrinkles

Graphene-based thermally conductive composites have been proposed as effective thermal management materials for cooling high-power electronic devices.However,when flexible graphene nanosheets are assembled into macroscopic thermally conductive composites,capillary forces induce shrinkage of graphene nanosheets to form wrinkles during solution-based spontaneous drying,which greatly reduces the thermal conductivity of the composites.Herein,graphene nanosheets/aramid nanofiber(GNS/ANF)composite films with high thermal conductivity were prepared by in-plane stretching of GNS/ANF composite hydrogel networks with hydrogen bonds andπ-πinteractions.The in-plane mechanical stretching eliminates graphene nanosheets wrinkles by suppressing inward shrinkage due to capillary forces during drying and achieves a high in-plane orientation of graphene nanosheets,thereby creating a fast in-plane heat transfer channel.The composite films(GNS/ANF-60 wt%)with eliminated graphene nanosheets wrinkles showed a significant increase in thermal conductivity(146 W m^(−1)K^(−1))and tensile strength(207 MPa).The combination of these excellent properties enables the GNS/ANF composite films to be effectively used for cooling flexible LED chips and smartphones,showing promising applications in the thermal management of high-power electronic devices.

Ultra-broadband microwave absorber and high-performance pressure sensor based on aramid nanofiber,polypyrrole and nickel porous aerogel

Electronic devices have become ubiquitous in our daily lives,leading to a surge in the use of microwave absorbers and wearable sensor devices across various sectors.A prime example of this trend is the aramid nanofibers/polypyrrole/nickel(APN)aerogels,which serve dual roles as both microwave absorbers and pressure sensors.In this work,we focused on the preparation of aramid nanofibers/polypyrrole(AP15)aerogels,where the mass ratio of aramid nanofibers to pyrrole was 1:5.We employed the oxidative polymerization method for the preparation process.Following this,nickel was thermally evaporated onto the surface of the AP15 aerogels,resulting in the creation of an ultralight(9.35 mg·cm^(-3)).This aerogel exhibited a porous structure.The introduction of nickel into the aerogel aimed to enhance magnetic loss and adjust impedance matching,thereby improving electromagnetic wave absorption performance.The minimum reflection loss value achieved was-48.7 dB,and the maximum effective absorption bandwidth spanned 8.42 GHz with a thickness of 2.9 mm.These impressive metrics can be attributed to the three-dimensional network porous structure of the aerogel and perfect impedance matching.Moreover,the use of aramid nanofibers and a three-dimensional hole structure endowed the APN aerogels with good insulation,flame-retardant properties,and compression resilience.Even under a compression strain of 50%,the aerogel maintained its resilience over 500 cycles.The incorporation of polypyrrole and nickel particles further enhanced the conductivity of the aerogel.Consequently,the final APN aerogel sensor demonstrated high sensitivity(10.78 kPa-1)and thermal stability.In conclusion,the APN aerogels hold significant promise as ultra-broadband microwave absorbers and pressure sensors.

Polymer Fiber Rigid Network with High Glass Transition Temperature Reinforces Stability of Organic Photovoltaics

Organic photovoltaics(OPVs)need to overcome limitations such as insufficient thermal stability to be commercialized.The reported approaches to improve stability either rely on the development of new materials or on tailoring the donor/acceptor morphology,however,exhibiting limited applicability.Therefore,it is timely to develop an easy method to enhance thermal stability without having to develop new donor/acceptor materials or donor–acceptor compatibilizers,or by introducing another third component.Herein,a unique approach is presented,based on constructing a polymer fiber rigid network with a high glass transition temperature(T_(g))to impede the movement of acceptor and donor molecules,to immobilize the active layer morphology,and thereby to improve thermal stability.A high-T_(g) one-dimensional aramid nanofiber(ANF)is utilized for network construction.Inverted OPVs with ANF network yield superior thermal stability compared to the ANF-free counterpart.The ANF network-incorporated active layer demonstrates significantly more stable morphology than the ANF-free counterpart,thereby leaving fundamental processes such as charge separation,transport,and collection,determining the device efficiency,largely unaltered.This strategy is also successfully applied to other photovoltaic systems.The strategy of incorporating a polymer fiber rigid network with high T_(g) offers a distinct perspective addressing the challenge of thermal instability with simplicity and universality.

Laser-Induced Graphene Conductive Fabric Decorated with Copper Nanoparticles for Electromagnetic Interference Shielding Application

To meet the demands for flexible electromagnetic interference(EMI)shielding materials,a type of conductive fabric is prepared by generating three-dimensional(3D)porous laser-induced graphene(LIG)in situ on the surface of the aramid fabric(AF)and then electroless plating copper.After LIG treatment,the porous AF demonstrates admirable conductivity due to the generation of graphene.The superior surface resistance of the conductive fabric can reach 1.57Ω/sq after copper deposition,and the average EMI shielding effectiveness(SE)can reach 34.3 dB in a frequency range of 8.2 to 12.4 GHz,with the EMW absorption accounting for about 80%.The proposed technology provides a new idea for preparation of flexible EMI shielding materials.

Body armour-New materials, new systems

This is a very timely review of body armour materials and systems since new test standards are currently being written, or reviewed, and new, innovative products released. Of greatest importance, however, is the recent evolution, and maturity, of the Ultra High Molecular Weight Polyethylene fibres enabling a completely new style of system to evolve e a stackable system of Hard Armour Plates. The science of body armour materials is quickly reviewed with emphasis upon current understanding of relevant energy-absorbing mechanisms in fibres, fabrics, polymeric laminates and ceramics. The trend in ongoing developments in ballistic fibres is then reviewed, analysed and future projections offered. Weaknesses in some of the ceramic grades are highlighted as is the value of using cladding materials to improve the robustness, and multi-strike performance, of Hard Armour Plates. Finally, with the drive for lighter, and therefore smaller, soft armour systems for military personnel the challenges for armour designers are reported, and the importance of the relative size of the Hard Armour Plate to the Soft Armour Insert is strongly emphasised.

Critical interfaces in body armour systems

The ballistic performance,and behaviour,of an armour system is governed by two major sets of variables,geometrical and material.Of these,the consistency of performance,especially against small arms ammunition,will depend upon the consistency of the properties of the constituent materials.In a body armour system for example,fibre diameter,areal density of woven fabric,and bulk density of ceramic are examples of critical parameters and monitoring such parameters will form the backbone of associated quality control procedures.What is often overlooked,because it can fall into the User’s domain,are the interfaces that exist between the various products;the carrier,the Soft Armour Insert(SAI),and the one or two hard armour plates(HAP1 and HAP2).This is especially true if the various products are sourced from different suppliers.

国产芳纶上浆剂对聚三唑复合材料力学性能的影响

目的研究国产芳纶纤维DAF-III表面上浆剂的主要成分及其对复合材料界面性能的影响。方法用丙酮溶剂抽提纤维一定时间,分析对比去除上浆剂前后的纤维和抽提溶液,并制备DAF-III增强的聚三唑树脂复合材料,测试复合材料的力学性能。结果国产DAF-III芳纶纤维的主体结构是聚酰胺苯并咪唑,表面上浆剂主要组分是脂肪族酯类低聚物。溶剂抽提去除了纤维表面大部分上浆剂,裸露的纤维本体存在制备过程中形成的沿纤维方向的大量沟壑;去除上浆剂后,复合材料的ILSS和弯曲强度分别提高了181.2%和56.20%。结论纤维表面上浆剂对纤维以及纤维增强的复合材料力学性能影响显著,纤维与树脂通过机械锚合和氢键作用改善界面粘接。

芳纶Ⅲ与芳纶Ⅱ防弹性能研究

选用两种不同型号芳纶,通过单向复合工艺分别制造成靶板。以NIJⅢA标准通过弹道试验,测试出两种靶板的弹坑凹陷深度与子弹穿透层数差异,并进一步通过测试两种芳纶SEA值比较其防弹性能差别,结果表明,芳纶Ⅲ抗弹性能比芳纶Ⅱ提高近30%。最后讨论了纤维力学性能对其防弹性能的影响,指出更高的拉伸强度和断裂伸长率是芳纶Ⅲ抗弹性能更优的主要原因,并预测芳纶Ⅲ的抗弹性能还有进一步提升的空间。

Super-Tough and Environmentally Stable Aramid Nanofiber@MXene Coaxial Fibers with Outstanding Electromagnetic Interference Shielding Efficiency

Although electrically conductive and hydrophilic MXene sheets are promising for multifunctional fibers and electronic textiles,it is still a challenge to simultaneously enhance both conductivity and mechanical properties of MXene fibers because of the high rigidity of MXene sheets and insufficient inter-sheet interactions.Herein,we demonstrate a core-shell wet-spinning methodology for fabricating highly conductive,super-tough,ultra-strong,and environmentally stable Ti_(3)C_(2)T_(x) MXene-based core-shell fibers with conductive MXene cores and tough aramid nanofiber(ANF)shells.The highly orientated and low-defect structure endows the ANF@MXene core-shell fiber with supertoughness of~48.1 MJ m^(-3),high strength of~502.9 MPa,and high conductivity of~3.0×10^(5)S m^(-1).The super-tough and conductive ANF@MXene fibers can be woven into textiles,exhibiting an excellent electromagnetic interference(EMI)shielding efficiency of 83.4 dB at a small thickness of 213μm.Importantly,the protection of the ANF shells provides the fibers with satisfactory cyclic stability under dynamic stretching and bending,and excellent resistance to acid,alkali,seawater,cryogenic and high temperatures,and fire.The oxidation resistance of the fibers is demonstrated by their wellmaintained EMI shielding performances.The multifunctional core-shell fibers would be highly promising in the fields of EMI shielding textiles,wearable electronics and aerospace.

Statistical Tensile Strength for High Strain Rate of Aramid and UHMWPE Fibers

Dynamic tensile impact properties of aramid (Technora) and UHMWPE (DC851) fiber bundles were studied at two high strain rates by means of reflecting type Split Hopkinson Bar, and stress-strain curves of fiber yarns at different strain rates were obtained. Experimental results show that the initial elastic modulus, failure strength and unstable strain of aramid fiber yarns are strain rate insensitive, whereas the initial elastic modulus and unstable strain of UHMWPE fiber yarns are strain rate sensitive. A fiber-bundle statistical constitutive equation was used to describe the tensile behavior of aramid and UHMWPE fiber bundles at high strain rates. The good consistency between the simulated results and experimental data indicates that the modified double Weibull function can represent the tensile strength distribution of aramid and UHMWPE fibers and the method of extracting Weibull parameters from fiber bundles stress-strain data is valid.

Investigation of the mechanical and ballistic properties of hybrid carbon/aramid woven laminates

High-performance ballistic fibers,such as aramid fiber and ultra-high-molecular-weight polyethylene(UHMWPE),are commonly used in anti-ballistic structures due to their low density,high tensile strength and high specific modulus.However,their low modulus in the thickness direction and insufficient shear strength limits their application in certain ballistic structure.In contrast,carbon fiber reinforced epoxy resin matrix composites(CFRP)have the characteristics of high modulus in the thickness direction and high shear resistance.However,carbon fibers are rarely used and applied for protection purposes.A hybridization with aramid fiber reinforced epoxy resin matrix composites(AFRP)and CFRP has the potential to improve the stiffness and the ballistic property of the typical ballistic fiber composites.The hybrid effects on the flexural property and ballistic performance of the hybrid CFRP/AFRP laminates were investigated.Through conducting mechanical property tests and ballistic tests,two sets of reliable simulation parameters for AFRP and CFRP were established using LS-DYNA software,respectively.The experimental results suggested that by increasing the content of CFRP that the flexural properties of hybrid CFRP/AFRP laminates were enhanced.The ballistic tests'results and the simulation illustrated that the specific energy absorption by the perforation method of CFRP achieved 77.7%of AFRP.When CFRP was on the striking face,the shear resistance of the laminates and the resistance force to the projectiles was promoted at the initial penetration stage.The proportion of fiber tensile failures in the AFRP layers was also enhanced with the addition of CFRP during the penetration process.These improvements resulted in the ballistic performance of hybrid CFRP/AFRP laminates was better than AFRP when the CFRP content was 20 wt%and 30 wt%.

Self-Exfoliation of Flake Graphite for Bioinspired Compositing with Aramid Nanofiber toward Integration of Mechanical and Thermoconductive Properties

Flexible yet highly thermoconductive materials are essential for the development of next-generation flexible electronic devices.Herein,we report a bioinspired nanostructured film with the integration of large ductility and high thermal conductivity based on self-exfoliated pristine graphene and three-dimensional aramid nanofiber network.A self-grinding strategy to directly exfoliate flake graphite into few-layer and few-defect pristine graphene is successfully developed through mutual shear friction between graphite particles,generating largely enhanced yield and productivity in comparison to normal liquid-based exfoliation strategies,such as ultrasonication,high-shear mixing and ball milling.Inspired by nacre,a new bioinspired layered structural design model containing three-dimensional nanofiber network is proposed and implemented with an interconnected aramid nanofiber network and high-loading graphene nanosheets by a developed continuous assembly strategy of sol-gel-film transformation.It is revealed that the bioinspired film not only exhibits nacre-like ductile deformation behavior by releasing the hidden length of curved aramid nanofibers,but also possesses good thermal transport ability by directionally conducting heat along pristine graphene nanosheets.

Behavior of Aramid Fiber/Ultrahigh Molecular Weight Polyethylene Fiber Hybrid Composites under Charpy Impact and Ballistic Impact

The aramid fiber礥HMWPE (ultrahigh molecular weight polyethylene) fiber hybrid composites (AF礑F) were ma-nufactured. By Charpy impact, the low velocity impact behavior of AF礑F composite was studied. And the high velocity impact behavior under ballistic impact was also investigated. The influence of hybrid ratio on the performances of low and high velocity impact was analyzed, and hybrid structures with good impact properties under low velocity impact and high velocity were optimized. For Charpy impact, the maximal impact load increased with the accretion of the AF layers for AF礑F hybrid composites. The total impact power was reduced with the decrease of DF layers and the delamination can result in the increase of total impact power. For ballistic impact, the DF ballistic performance was better than that of the AF and the hybrid ratio had a crucial influence. The failure morphology of AF礑F hybrid composite under Charpy impact and ballistic impact was analyzed. The AF礑F hybrid composites in suitable hybrid ratio could attain better performance than AF or DF composites.

Analysis and Control of Surface Delamination Defects During Milling of Orthogonal Aramid Fiber‑Reinforced Composites Laminates

The aramid fiber-reinforced composites(AFRC)can increase the durability of corresponding applications such as aerospace,automobile and other large structural parts,due to the improvement in hardness,heat build-up,wear properties and green environmental protection.However,because of its complex multiphase structure and unique heterogeneity and anisotropy,the poor compression fatigue resistance and the incident surface fibrillation are inevitable.To improve the assembly precision of AFRC,mechanical processing is necessary to meet the dimensional accuracy.This paper focuses on the influence of contour milling parameters on delamination defects during milling of AFRC laminates.A series of milling experiments are conducted and two different kinds of delamination defects including tearing delamination and uncut-off delamination are investigated.A computing method and model based on brittle fracture for the two different types of delamination are established.The results can be used for explaining the mechanism and regularity of delamination defects.The control strategy of delamination defects and evaluation method of finished surface integrity are further discussed.The results are meaningful to optimize cutting parameters,and provide a clear understanding of surface defects control.

Tensile Properties of Fiber Materials under Different Strain Rates

The quasi-static and dynamic tensile tests of aramid and high strength PVA fiber bundles are carried out under a wider range of strain rate by use of MTS (Materials Testing System) and bar-bar tensile impact apparatus. The influences of strain rate on mechanical properties of aramid and high strength polyvinyl alcohol fibers are studied. Micro failure mechanisms of fibers at different strain rates are examined by means of SEM.

Plasma-induced graft polymerization on the surface of aramid fabrics with improved omniphobicity and washing durability

Durable superomniphobic surfaces are desirable for their practical applications,including selfcleaning,non-fouling,protective clothing and the separation of liquids.The plasma-induced polymerization of environmentally friendly C6 from a perfluoralkyl methlacrylate copolymer emulsion,AG-E081,was performed and a durable omniphobic fabric was achieved.C6 is an ecological alternative to C8(eight CF2 groups)fluorinated compounds,and it was thereafter successfully incorporated into aramid fabric to achieve a durable superomniphobic surface.The fabric became water and oil repellent with an extremely high water contact angle of 180°.As tested by the water spray AATCC test and hydrocarbon resistance test,the as-prepared fabric gained 100°(ISO 5)and grade number 4 respectively.Furthermore,the fabrics also showed significantly improved washing durability after ten washing cycles.By scanning electron microscopy(SEM),Fourier-transform infrared spectroscopy(FTIR)and x-ray photoelectron spectroscopy(XPS)tests,it is indicated that the durable superomniphobicity can be attributed to the roughness and activation of the aramid surface by the plasma pre-treatment,which induces more adsorption and chemical graft of the C6 copolymer.

Statistical Constitutive Equation of Aramid Fiber Bundles

Tensile impact tests of aramid (Twaron) fiber bundles were carried out under high strain rates with a wide range of 0. 01/s -1 000/s by using MTS and bar-bar tensile impact apparatus. Based on the statistical constitutive model of fiber bundles, statistical constitutive equations of aramid fiber bundles are derived from statistical analysis of test data at different strain rates. Comparison between the theoretical predictions and experimental data indicates statistical constitutive equations fit well with the experimental data, and statistical constitutive equations of fiber bundles at different strain rates are valid.

Atmospheric air dielectric barrier discharge excited by nanosecond pulse and AC used for improving the hydrophilicity of aramid fibers

In this paper, a long line-shape dielectric barrier discharge excited by a nanosecond pulse and AC is generated in atmospheric air for the purpose of discussing the uniformity, stability and ability of aramid fiber treatment. The discharge images, waveforms of current and voltage,optical emission spectra, and gas temperatures of both discharges are compared. It is found that nanosecond pulsed discharge has a more uniform discharge morphology, higher energy efficiency and lower gas temperature, which indicates that nanosecond pulsed discharge is more suitable for surface modification. To reduce the water contact angle from 96° to about 60°, the energy cost is only about 1/7 compared with AC discharge. Scanning electron microscopy,Fourier transform infrared spectroscopy and x-ray photoelectron spectroscopy are employed to understand the mechanisms of hydrophilicity improvement.

Shear Performance of FRCC Beam-Column Joints Using Various Polymer Fibers

Brittle shear failure should be avoided in beam-column joint of a reinforced concrete(RC)frame during the earthquake.Fiber-reinforced cementitious composite(FRCC)which presents a remarkable deformability especially under tensile and bending load with a large energy absorption capacity is expected to be used in the crucial part of a RC frame.With the development of polymer material,various synthetic fibers have become the best selection to improve concrete capacity and failure resistance without the corrosion of fibers.The objective of this study is to investigate the influence of fiber bridging effect on the shear capacity of FRCC beam-column joint.The main parameter of the test in the present study is the fiber types:aramid,polypropylene(PP)and polyvinyl alcohol(PVA)fiber.To evaluate shear capacity quantitatively,a new calculation method using FRCC tensile characteristics confirmed by the uniaxial tension test is newly proposed.The difference of below 7%between calculated value and experimental value demonstrates that the calculation method is feasible.

Effect of the Weaving Density of Aramid Fabrics on Their Resistance to Ballistic Impacts

Two Heracron? woven fabrics, HT600-1 and HT600-2, were fabricated with different weaving densities and their resistance to ballistic impact was investigated. While HT600-1 was inherently stronger along the weft than HT600-2, the latter exhibited a higher tensile strength along the warp. Crimp values indicate that HT600-1, which possesses a relatively larger weft weaving density, induces an excess in the warp crimp ratio, thereby weakening the fabric along the warp. The dimensionless fiber property U*, which is defined as the product of the specific fiber toughness and the strain wave velocity, was calculated for each fabric. The U* values of HT600-1 were lower than those of HT600-2;U* values along the warp of HT600-1 were extremely low. These analyses show that HT600-2 exhibited improved ballistic properties over those of HT600-1. These findings further indicate the existence of an optimal weave that would minimize damage to both yarn and fabric. Establishing these optimal conditions can be crucial in implementing better ballistic properties into fabrics.