Effect of arc re-melting on microstructure,mechanical and tribological properties of commercial 390A alloy

To investigate the effect of the arc re-melting on the microstructure,mechanical and tribological properties of the 390 A alloy,its ingot produced by the conventional induction melting method was subjected to the arc re-melting process.The microstructure of the 390 A alloy was examined by OM and SEM.Mechanical properties of the 390 A alloy were determined by the Brinell method and tensile tests.Tribological properties were investigated with a ball-on-disc type tester.It was observed that the microstructure of both conventional induction melted and arc re-melted 390 A alloys consisted ofα(Al),eutectic Al-12 Si,primary silicon particles,θ-CuAl_(2),β-Al_(5) FeSi,δ-Al_(4) FeSi_(2),andα-Al_(15)(FeMnCu)3 Si_(2) phases.Re-melting with the arc process caused grain refinement in these phases.In addition,after this process,theα(Al)phase and primary silicon particles were dispersed more uniformly,and sharp edges of primary silicon particles became round.The arc re-melting process resulted in an increase in the hardness of the 390 A alloy produced by the conventional method from 102 HB to 118 HB and the tensile strength from 130 to 240 MPa.It also caused an increase in the wear resistance of the 390 A alloy and a decrease in the friction coefficient.

Study on anisotropy of microstructure and mechanical properties of AZ31 magnesium alloy fabricated by wire arc additive manufacturing

Based on wire arc additive manufacturing(WAAM)technology,AZ31 magnesium alloy in bulk was successfully fabricated,and its microstructure as well as mechanical properties in different planes were observed and analyzed.The AZ31 magnesium alloy has a similar microstructure in the building direction(Z)and travel direction(X),both of which are equiaxed grains.There are heat-affected zones(HAZs)with coarse grains below the fusion line.The second phase is primarily composed of the Mg17Al12 phase,which is evenly distributed in different directions.In addition,the residual stress varies in different directions.There is no significant difference in the hardness of the AZ31 alloy along the Z and X directions,with the average hardness being 68.4 HV and 67.9 HV,respectively.Even though the specimens’ultimate tensile strength along the travel direction is higher in comparison to that along the building direction,their differences in elongation and yield strength are smaller,indicating that the anisotropy of the mechanical properties of the material is small.

Effects of annealing on microstructure and mechanical properties of γ-TiAl alloy fabricated via laser melting deposition

The microstructure evolution and mechanical properties of the as-deposited γ-TiAl-based alloy specimen fabricated via laser melting deposition and as-annealed specimens at different temperatures were investigated.The results show that the microstructure of as-deposited specimen is composed of fineα2(Ti3Al)+γlamellae.With the increase of annealing temperature,the bulk γ m(TiAl)phase gradually changes from single γ phase toγphase+acicularα2 phase,finally small γ phase+lamellar α2+γ phase.Compared with the mechanical properties of as-depositedγ-TiAl alloy(tensile strength 469 MPa,elongation 1.1%),after annealing at 1260℃ for 30 min followed by furnace cooling(FC),the room-temperature tensile strength of the specimen is 543.4 MPa and the elongation is 3.7%,which are obviously improved.

Influence of process parameters and aging treatment on the microstructure and mechanical properties of Al Si8Mg3 alloy fabricated by selective laser melting

Many studies have investigated the selective laser melting(SLM)of AlSi10Mg and AlSi7Mg alloys,but there are still lack of researches focused on Al-Si-Mg alloys specifically tailored for SLM.In this work,a novel high Mg-content AlSi8Mg3 alloy was specifically designed for SLM.The results showed that this new alloy exhibited excellent SLM processability with a lowest porosity of 0.07%.Massive lattice distortion led to a high Vickers hardness in samples fabricated at a high laser power due to the precipitation of Mg_(2)Si nanoparticles from theα-Al matrix induced by high-intensity intrinsic heat treatment during SLM.The maximum microhardness and compressive yield strength of the alloy reached HV(211±4)and(526±12)MPa,respectively.After aging treatment at 150℃,the maximum microhardness and compressive yield strength of the samples were further improved to HV(221±4)and(577±5)MPa,respectively.These values are higher than those of most known aluminum alloys fabricated by SLM.This paper provides a new idea for optimizing the mechanical properties of Al-Si-Mg alloys fabricated using SLM.

Effect of heat treatment on the microstructure and mechanical properties of AZ80M magnesium alloy fabricated by wire arc additive manufacturing

To maximize the benefits of wire arc additive manufacturing(WAAM)processes,the effect of post-deposition heat treatment on the microstructure and mechanical properties of WAAM AZ80M magnesium(Mg)alloy was investigated.Three different heat treatment procedures(T4,T5 and T6)were performed.According to the results,after T4 heat treatment,the microsegregation of alloying elements was improved with the eutectic structure dissolved.Samples after T5 heat treatment inherited the net-like distribution of secondary phases similar to the as-deposited sample,where the eutectic structure covering the interdendritic regions and theβ-phase precipitated around the eutectic structure.After T6 heat treatment,the tinyβ-phases re-precipitated from the matrix and distributed in inner and outer of the grains.The hardness distribution of the samples went through T4 and T6 heat treatment was more uniform in comparison to that of T5 heat treated samples.The tensile test showed that the T6 heat treatment improved the strength and ductility,and the anisotropy between horizontal and vertical can be eliminated.Moreover,T4 treated samples exhibited highest ductility.

Effect of Nb additions on microstructure and properties of γ-TiAl based alloys fabricated by selective laser melting

The γ-TiAl based Ti.Al.Mn.Nb alloys with different Nb additions were fabricated by selective laser melting (SLM) on the TC4 substrate. The effects of Nb content on microstructure and properties of the alloys were investigated. The results reveal that the alloys consist of γ-TiAl phase with tetragonal lattice structure and α2-Ti3Al phase with hcp lattice structure, and show a sequential structure change from near full dendrite to near lamellar structure with the increase of Nb addition. Owing to the higher Nb content in γ-TiAl phase and the formation of near lamellar structure, the alloy with 7.0 at.% Nb addition has the best combination of properties among the studied alloys, namely, not only a high hardness of HV 2000, a high strength of 1390 MPa and a plastic deformation of about 24.5%, but also good tribological properties and high-temperature oxidation resistance.

A review on microstructures and properties of high entropy alloys manufactured by selective laser melting

High entropy alloys(HEAs)with multi-component solid solution microstructures have the potential for large-scale industrial applications due to their excellent mechanical and functional properties.However,the mechanical properties of HEAs limit the selection of processing technologies.Additive manufacturing technology possesses strong processing adaptability,making itthe best candidate method to overcome this issue.This comprehensive review examines the current state of selective laser melting(SLM)of HEAs.Introducing SLM to HEAs processing is motivated by its high quality for dimensional accuracy,geometric complexity,surface roughness,and microstructure.This review focuses on analyzing the current developments and challenges in SLM of HEAs,including defects,microstructures,and properties,as well as strengthing prediction models of fabricated HEAs.This review also offers directions for future studies to address existing challenges and promote technological advancement.

A Comparative Study on the Microstructures and Mechanical Properties of Two Kinds of Iron-Based Alloys by WAAM

In order to adapt to the high temperature and heavy load process environment of large forgings,a novel die with"fist-like"structure is designed.The“fist-like”die mainly consists of“skin”layer,“bone”layer and matrix.To obtain the material with good supportability and good bonding strength with the“skin”layer,iron-based alloys RMD248 and CN72 were selected to make the"bone"layer,and the properties were compared.In this paper,the"bone"layer and the"skin"layer(CHN327)were surfaced on 5CrNiMo matrix by wire arc additive manufacture(WAAM).Then,cyclic heating to 500℃and thermal compression with a maximum deformation of 30%were adapted to test the high temperature mechanical properties.The microstructure changes before and after thermal cycles and compressions were observed by optical microscopy(OM),X-ray diffraction(XRD),energy dispersive spectrometer(EDS)and scanning electron microscopy(SEM).The results show that CN72 has more carbides than RMD248 at the joint surface,which makes it easy to form brittle fracture at the joint.Mechanical properties were tested by using microhardness machine.Meanwhile,hot tensile tests were performed to study bonding strength between the“skin”layer and the“bone”layer.The results show that the RMD248 has stable microhardness distribution while the microhardness of CN72 decreases with the distance from the interface.And the ultimate tensile strength between CN72 and CHN327 is higher than RMD248 in the temperature range of 400-450℃.It can be inferred that CN72 has higher inter-layer wear resistance and RMD248 has more stable high temperature performance.

Effects of graphene nanoplates on microstructures and mechanical properties of NSA-TIG welded AZ31 magnesium alloy joints

The effects of graphene nanoplates(GNPs)on the microstructures and mechanical properties of nanoparticlesstrengthening activating tungsten inert gas arc welding(NSA-TIG)welded AZ31magnesium alloy joints were investigated.It wasfound that compared with those of activating TIG(A-TIG),and obvious refinement ofα-Mg grains was achieved and the finestα-Mggrains of fusion zone of NSA-TIG joints were obtained in the welded joints with TiO2+GNPs flux coating.In addition,thepenetrations of joints coated by TiO2+GNPs flux were similar to those coated by the TiO2+SiCp flux.However,the welded jointswith TiO2+GNPs flux coating showed better mechanical properties(i.e.,ultimate tensile strength and microhardness)than those withTiO2+SiCp flux coating.Moreover,the generation of necking only occurred in the welded joints with TiO2+GNPs flux.

EFFECT OF MELT SUPERHEATING ON MICROSTRUCTURE AND MECHANICAL PROPERTIES OF A357 ALLOY

ＥＦＦＥＣＴＯＦＭＥＬＴＳＵＰＥＲＨＥＡＴＩＮＧＯＮＭＩＣＲＯＳＴＲＵＣＴＵＲＥＡＮＤＭＥＣＨＡＮＩＣＡＬＰＲＯＰＥＲＴＩＥＳＯＦＡ３５７ＡＬＬＯＹ①ＬｉＰｅｉｙｏｎｇ１，２，ＪｉａＪｕｎ，ＧｕｏＪｉｎｇｊｉｅ，ＬｉＰｅｉｊｉｅ，ＳｈａｏＧａｏｌｉａ...

Influence of Electroshocking Treatment on Microstructure and Mechanical Properties of Ti-6.5Al-3.5Mo-1.5Zr-0.3Si Thin-Wall Specimen Manufactured by Laser Melting Deposition

In order to improve the properties of titanium alloys manufactured by laser melting deposition(LMD),the electroshocking treatment(EST)was proposed in this work.The effects of EST on microstructure and mechanical properties of LMD Ti-6.5Al-3.5Mo-1.5Zr-0.3Si were investigated.The results showed that the width of the heat affected band decreased and disappeared under the thermal and athermal effects of EST,resulting in the uniform microstructure.In the microstructure,theαlaths became coarser gradually,and the quantity ofα/βinterface was reduced.The reduction of the quantity ofα/βinterface leads to make less resistant to dislocation,resulting in the reduction in hardness and strength.The discontinuous grain boundaryαphase and nucleationαcolony near grain boundary inhibited the crack propagation and improved the ductility.Summary,EST can manipulate the microstructure and improve the mechanical properties of LMD titanium alloys.

Formability,microstructure evolution and mechanical properties of wire arc additively manufactured AZ80M magnesium alloy using gas tungsten arc welding

Wire arc additive manufacturing(WAAM)technology has been used to fabricate the multi-layer single-pass deposited wall of AZ80M magnesium(Mg)alloy by gas tungsten arc welding.The formability,thermal cycles,microstructural evolution and mechanical properties of the WAAM AZ80M Mg alloy were investigated.The results show that there was significant difference in the temperature variation and the geometries between the original several layers and the subsequent deposited layers.Owing to the arc energy input,the interpass temperature rised rapidly and then stabilized at 150℃.As a result,the width of the deposited wall increased and then kept stable.There were obvious differences in the microstructure of the WAAM AZ80M Mg alloy among the top zone,intermediate zone and bottom zone of deposited wall.During the arc deposition process,theβphase of the WAAM AZ80M Mg alloy redissolved due to the cyclic heat accumulation,and then precipitated in the grain boundary.The cyclic heat accumulation also led to weakening of dendrite segregation.From the substrate to the top zone,the hardness of the deposited wall decreased gradually,and the intermediate zone which was the main body of deposited wall had relatively uniform hardness.The tensile properties of the WAAM AZ80M Mg alloy were different between the vertical direction and the horizontal direction.And the maximum ultimate tensile strength of the WAAM AZ80M Mg alloy was 308 MPa which was close to that of the as-extruded AZ80M Mg alloy.

Microstructure and mechanical properties of high-strength low alloy steel by wire and arc additive manufacturing

A high-building multi-directional pipe joint(HBMDPJ)was fabricated by wire and arc additive manufacturing using high-strength low-alloy(HSLA)steel.The microstructure characteristics and transformation were observed and analyzed.The results show that the forming part includes four regions.The solidification zone solidifies as typical columnar crystals from a molten pool.The complete austenitizing zone forms from the solidification zone heated to a temperature greater than 1100℃,and the typical columnar crystals in this zone are difficult to observe.The partial austenitizing zone forms from the completely austenite zone heated between Ac1(austenite transition temperature)and1100℃,which is mainly equiaxed grains.After several thermal cycles,the partial austenitizing zone transforms to the tempering zone,which consistes of fully equiaxed grains.From the solidification zone to the tempering zone,the average grain size decreases from 75 to20μm.The mechanical properties of HBMDPJ satisfies the requirement for the intended application.

Influence of hot isostatic pressing on microstructure,properties and deformability of selective laser melting TC4 alloy

The influence of different hot isostatic pressing regimes on microstructure,phase constitution,microhardness,tensile properties and deformability of TC4 alloy fabricated by selective laser melting(SLM)technology was studied.The results show that the microstructure of SLM TC4 alloy is composed of acicular martensiteα’phase,and the sample exhibits high microhardness and strength,but low plasticity.After hot isostatic pressing,acicular martensiteα’phase transforms intoα+βphase,and with the increase of hot isostatic pressing temperature and duration,αphase with coarse lath is gradually refined,and the proportion ofαphase is gradually reduced.Because of the change of phase constitution in SLM TC4 alloy after hot isostatic pressing,the grain refinement strengthening is weakened,the density of dislocation is reduced,so that both microhardness and tensile strength are decreased by around 20%,the elongation is increased by more than about 70%,even over 100%,compared with as-deposited TC4 alloy.When the hot isostatic pressing regime is 940°C/3 h/150 MPa,the tensile strength and the elongation achieve optimal match,which are about890 MPa and around 14.0%in both directions.The fracture mechanism of alloy after 940 oC/3 h/150 MPa HIP is dultile fracture.Hot isostatic pressing causes concave deformation of SLM TC4 alloy thin-walled frames,and the deformation degree increases with the increase of temperature.

Solidification microstructure evolution and its correlations with mechanical properties and damping capacities of Mg-Al-based alloy fabricated using wire and arc additive manufacturing

Magnesium(Mg)alloys,as the lightest metal structural material with good damping capacities,have im-portant application prospects in realizing structural lightweight and vibration reduction.However,their engineering application is greatly limited by poor plastic formability.Wire and arc additive manufactur-ing(WAAM)provides a potential approach for fabricating large-scale Mg alloy components with high manufacturing flexibility.In this study,the evolution of the solidification microstructure of a WAAM-processed Mg-Al-based alloy was quantitatively analyzed based on the analytical models;then,the cor-relations between the solidification microstructure and mechanical properties/damping capacities were investigated.The results revealed that the WAAM-processed Mg-Al-based alloy with an equiaxed-grain-dominated microstructure displayed a simultaneous enhancement in mechanical properties and damping capacities compared to those of the cast Mg-Al-based alloy.The good combination of mechanical prop-erties and damping capacities are mainly attributed to the weakened basal texture with a relatively high Schmid factor for basalslip,the twinning-induced plasticity(TWIP)effect associated with the profuse{10-12}tensile twinning,and the relatively high dislocation density caused by the thermal stress during the WAAM process.

Effects of heat treatment on microstructures and properties of a heterostructured alloy with dissimilar components fabricated by WAAM

Heat treatment significantly influences homogeneous material microstructures and mechanical properties,which can be improved by an optimal heat treatment process.However,heat treatment application to heterogeneous materials presents significant challenges due to compositional and microstructural heterogeneities.Herein,a laminated heterostructured alloy comprising alternating316L stainless steel(SS)and 18Ni300 maraging steel(MS)layers fabricated using wire and arc additive manufacturing was investigated.A solution treatment was applied at900℃for 0.5 h.Subsequently,the solution-treated and asfabricated(AF)samples were aged at 500℃for 4 h;these samples were denoted SA and AT,respectively.The AT phase compositions and orientations were similar to those of AF.The SA 316L SS layer resembled that of AF,but the SA 18Ni300 MS layers exhibited a reduced austenite phase fraction and refined grain size,attributable to solid-state transformation.In the AT sample,aging induced the formation of nanoscale acicularωphase and ellipsoidal Ni_(3)Ti,Fe_(2)Mo,and X precipitates in the 18Ni300 MS layers.Conversely,the SA precipitates contained acicular Fe Ni_(2)and ellipsoidalω,Ni_(3)Ti,and X precipitates,and their fractions were lower than those in AT precipitates.The18Ni300 MS layer microhardness in the heat-treated samples increased due to nanoprecipitation,but the 316L SS layer microhardness resembled that of AF.The AT and SA ultimate tensile strengths increased to(1360±50)and(1473±41)MPa,respectively,attributable to precipitation strengthening.The SA 316L SS layer exhibited a high stress-induced martensite fraction,enhancing the ductility of heated samples.

Microstructure evolution and mechanical properties of ZK60 magnesium alloy produced by SSTT and RAP route in semi-solid state

The microstructure evolution and mechanical properties of a ZK60 magnesium alloy produced by the semi-solid thermal transformation （SSTT） route and the recrystallization and partial melting （RAP） route were studied, respectively. The microstructure evolution during partial remelting was studied at different temperatures for different time. The tensile mechanical properties of thixoformed components by the two routes at room temperature were examined. The results show that coalescence is dominant in the SSTT alloy and Ostwald ripening is dominant in the RAP alloy. Compared with the SSTT route, the RAP route can produce finer semi-solid microstructure under the similar isothermal holding condition. The microstructure of the RAP alloy is much more spheroidized compared with the SSTT alloy. Thixoforming for the ZK60 magnesium alloy produced by the SSTT and RAP route results in successful filling of the die, and the thixoforming process improves the mechanical properties of ZK60 magnesium alloy. The RAP alloy shows significantly advantageous mechanical properties over that of the SSTT alloy.

Microstructural evolution and mechanical properties of laser melting deposited Ti-6.5Al-3.5Mo-1.5Zr-0.3Si titanium alloy

A rectangular plate of Ti-6.5A1-3.5Mo-I.5Zr-0.3Si titanium alloy was fabricated by laser melting deposition （LMD） technology. Macrostructure and microstructure were characterized by optical microscope （OM） and scanning electron microscope （SEM）. Room temperature tensile properties were evaluated. Results indicate that the macro-morphology is dominated by large columnar grains traversing multiple deposited layers. Two kinds of bands, named the wide bands and the narrow bands, are observed. The wide band consists of crab-like a lath and Widmanstatten a colony. The narrow band consists of a lath and transformed ft. The formation mechanism of the two bands was explored. The influence of heat effect caused by subsequent deposition layers on microstructural evolution during deposition process was discussed. The room temperature tensile test demonstrates that the strength of laser deposited Ti-6.5A1-3.5Mo-I.5Zr-0.3Si is comparable to that of wrought bars.

Microstructure and properties of AlSi7Mg alloy fabricated by selective laser melting

The AlSi7Mg alloy was fabricated by selective laser melting(SLM),and its microstructure and properties at different building directions after heat treatment were analyzed.Results show that the microstructure of SLM AlSi7Mg samples containes three zones:fine grain zone,coarse grain zone,and heat affected zone.The fine-grain regions locate inside the molten pool,and the grains are equiaxed.The coarse-grain regions locate in the overlap of molten pools.After T6 treatment,the microstructure at the molten pool boundary is still the network eutectic Si,but the network structure becomes discrete,and is composed of intermittent,chain-like eutectic Si particles.The yield strength at three directions(xy,45°,z direction)of the AlSi7Mg alloy samples fabricated by SLM is improved after T6 heat treatment.The fracture mechanism of the samples is a mixed ductile and brittle fracture before heat treatment and ductile fracture after heat treatment.

Influence of arc constriction current frequency on tensile properties and microstructural evolution of tungsten inert gas welded thin sheets of aerospace alloy

The main objective of this investigation is to study the influence of arc constriction current frequency(ACCF)on tensile properties and microstructural evolution of aerospace Alloy 718 sheets(2 mm in thickness)joined by constricted arc TIG(CA-TIG)welding process.One variable at a time approach of design of experiments(DOE)was used,in which ACCF was varied from 4 to 20 kHz at an interval of 5 levels while other parameters were kept constant.The joints welded using ACCF of 4 kHz exhibited superior tensile properties extending joint efficiency up to 99.20%.It is attributed to the grain refinement in fusion zone leading to the evolution of finer,discrete Laves phase in interdendritic areas.An increase of ACCF above 12 kHz caused severe grain growth and evolution of coarser Laves phase in fusion zone.Alloy 718 welds showed more obvious tendency for Nb segregation and Laves phase formation at higher levels of ACCF due to the slower cooling rate.The volume fraction of Laves phase was increased by 62.31%at ACCF of 20 kHz compared to that at 4 kHz,thereby reducing the tensile properties of joints.This is mainly due to the stacking of heat input in weld thermal cycles at increased levels of ACCF.