Failure Characteristics of Rock-like Mortar Specimens with Arc-shaped Flaws under Freezing-thaw Cycles and Uniaxial Compression

To investigate the freeze-thaw(F-T)damages and failure characteristics of rock mass with arc-shaped joints in cold regions,three types of cement mortar specimens with different central angles and prefabricated arc-shaped flaws are subjected to uniaxial compressive tests under different F-T cycles.Experimental observations show that the uniaxial compressive strength of specimens are significantly influenced by F-T cycles and their failure modes are mainly affected by the central angleαof the prefabricated flaws.Unlike the specimens with a central angle of 60°,the specimens with a central angle of 120°and 180°have greater curvature of flaws,so tensile cracks occur in the arc-top area of their prefabricated flaws.According to experimental images observed by environmental scanning electron microscope(ESEM),as the number of F-T cycles increases,the deterioration effect of the specimen becomes more obvious,which is specifically reflected in the increase of the mass loss,peak stress loss,and damage variables as a power function,and the peak strain decreases as a quadratic polynomial.According to numerical results using two-dimensional particle flow code(PFC2D),it is found that F-T cycles cause more damage to the specimen in the early stages than in the later ones.The area of the concentrated compressive stress zone in the middle is decreased due to the increased number of F-T cycles,while the area of the surrounding tensile-shear stress zone is increased.The models appear different failure modes due to the release of concentrated stress in different tensile-shear zones.

The Origins of the Arc-Shaped Langshan Uplift and Linhe Trench

In the northern part of the Ordos Basin, there is a 325 km long arc-shaped Langshan uplift and a 15 km-deep Linhe Trench in front of Langshan, which are rare geological phenomena for which origins no one has explained. This article comprehensively analyzes the research achievements over the past 40 years of geology, geomorphology, seismic exploration, paleogeography, and oil and gas exploration in the Ordos Basin and Langshan. It recognizes that the northern part of the Ordos Basin experienced a meteorite impact in the Late Cretaceous period. The impact pushed the block northwest ward, subducting after colliding with igneous rocks in the north. This sudden event formed a clear arc-shaped mountain zone in the north and a wedge-shaped trench in front of the mountain. The chaotic layers, prolonged and continuous faults, and numerous thrust layers in the Langshan, a negative anomaly area in the center of the northern Ordos, abnormal orientation of crystalline basement structures in the north of Ordos, Moho uplift, and distribution of meteorite fragments in the northwest of Langshan, all of these geological phenomena support the occurrence of the meteorite impact event, forming the arc-shaped Langshan and the Trench.

Wave Diffraction on Arc-Shaped Floating Perforated Breakwaters

An analytical method is developed to study the sheltering effects on arc-shaped floating perforated breakwaters. In the process of analysis, the tloating breakwater is assumed to be rigid, thin, vertical, and immovable and located in water with constant depth. The fluid domain is divided into two regions by imaginary interface. The velocity potential in each region is expanded by eigenfunction in the context of linear theory. By satisfying continuity of pressure and normal velocity across the imaginary fluid interface, a set of linear algebraic equations can be obtained to determine the unknown coefficients for eigenfunction expansions. The accuracy of the present model was verified by a comparison with existing results for the case of arc-shaped floating breakwater. Numerical results, in the form of contour maps of the non-dimensional wave amplitude around the breakwater and diffracted wave amplitude at typical sections, are presented for a range of wave and breakwater parameters. Results show that the sheltering effects on the arc-shaped floating perforated breakwater are closely related to the incident wavelength, the draft and the porosity of the breakwater.

Numerical simulations of rip currents off arc-shaped coastlines

The rip currents induced by waves off arc-shaped coastlines are seriously harmful to humans, but understanding of their characteristics is lacking. In this study, the FUNWAVE model was used to calculate the wave-induced currents in the Haller experiment and the ideal arc-shaped coast similar to Sanya Dadonghai, Hainan Province,China. The results showed that the FUNWAVE model has considerable ability to simulate the rip currents, and it was used to further simulate rip currents off arc-shaped coastlines to investigate their characteristics. The rip currents were found to be stronger as the curvature of arc-shaped coastline increased. Coastal beach slope exerts a significant influence on rip currents; in particular, an overly steep or overly mild slope is not conducive to creating rip currents. Furthermore, the rip currents were found to become weaker as the size of arc-shaped coast decreased. When the height and period of waves increase, the strength of rip currents also increases, and, in some cases, wave heights of 0.4 m may produce dangerous rip currents.

Plastic Mechanism of Multi-pass Double-roller Clamping Spinning for Arc-shaped Surface Flange

Compared with the conventional single-roller spinning process, the double-roller clamping spinning（DRCS） process can effectively prevent the sheet metal surface wrinkling and improve the the production efficiency and the shape precision of final spun part. Based on ABAQUS/Explicit nonlinear finite element software, the finite element model of the multi-pass DRCS for the sheet metal is established, and the material model, the contact definition, the mesh generation, the loading trajectory and other key technical problems are solved. The simulations on the multi-pass DRCS of the ordinary Q235A steel cylindrical part with the arc-shaped surface flange are carried out. The effects of number of spinning passes on the production efficiency, the spinning moment, the shape error of the workpiece, and the wall thickness distribution of the final part are obtained. It is indicated definitely that with the increase of the number of spinning passes the geometrical precision of the spun part increases while the production efficiency reduces. Moreover, the variations of the spinning forces and the distributions of the stresses, strains, wall thickness during the multi-pass DRCS process are revealed. It is indicated that during the DRCS process the radical force is the largest, and the whole deformation area shows the tangential tensile strain and the radial compressive strain, while the thickness strain changes along the generatrix directions from the compressive strain on the outer edge of the flange to the tensile strain on the inner edge of the flange. Based on the G-CNC6135 NC lathe, the three-axis linkage computer-controlled experimental device for DRCS which is driven by the AC servo motor is developed. And then using the experimental device, the Q235A cylindrical parts with the arc-shape surface flange are formed by the DRCS. The simulation results of spun parts have good consistency with the experimental results, which verifies the feasibility of DRCS process and the reliability of the finite element model for DRCS.

Study on Submerged Upper Arc-Shaped Plate Type Breakwater

Based on the wave radiation and diffraction theory, this paper investigates a new type breakwater with upper arcshaped plate by using the boundary element method(BEM). By comparing with other three designs of plate type breakwater(lower arc-shaped plate, single horizontal plate and double horizontal plate), this new type breakwater has been proved more effective. The wave exiting force, transmission and reflection coefficients are analyzed and discussed. In order to reveal the wave elimination mechanism of this type of breakwater, the velocity field around the breakwater is obtained. It is shown that:(1) The sway exciting force is minimal.(2) When the ratio of the submergence and wave amplitude is 0.05, the wave elimination effect will increase by 50% compared with other three types of breakwater.(3) The obvious backflow is found above the plate in the velocity field analysis.

Coastline configuration and geomorphologic development mode of arc-shaped coast in South China

Coastline configuration indexes of 34 typical arc-shaped coasts in South China are investigated by the method of principal component analysis, and meanwhile deposition and geomorphologic features of arc-shaped coast are also analyzed. The results show: (1) The configuration of arc-shaped coast in South China is of the characteristic of variability and complexity. (2) The wave power and the openings of the bay are the decisive factors to result in the changes of the configuration of the arc-shaped coast in South China, however, incidence direction of the wave has no effect on configuration development of the coast. (3) Commonly, geomorphologic modes of the arc-shaped coast system in South China consist of barriers, lagoons and tidal-inlets, and can be divided into four types:the openings of the bay leaning to the east, the openings of the bay leaning to the south, the openings of the bay leaning to the west and the openings of the bay leaning to the north.

Numerical simulations of stress wave propagation and attenuation at arc-shaped interface inlayered SiC/Al composite

The effects of interface shape on stress wave distribution and attenuation were investiga- ted using finite element method （ FEM ）. The simulation results indicate that when the stress wave propagates from SiC ceramic to A1 alloy, the tensile stress decreases and the attenuation coefficient of the stress wave increases with increasing central angle of the concave interface between SiC and A1. But for the convex interface, the tensile stress increases and attenuation coefficient decreases with increasing central angle. As the stress wave propagates from A1 alloy to SiC ceramic, the atten- uation coefficient of stress wave decreases with increasing the central angle of the concave interface. For the convex interface, the attenuation coefficient increases with increasing central angle.

Hydrodynamic Performance of the Arc-Shaped Bottom-Mounted Breakwater

The problem of the hydrodynamic interaction with the arc-shaped bottom-mounted breakwaters is investigated theoretically. The breakwater is assumed to be rigid, thin, impermeable and vertically located in a finite water depth. The fluid domain is divided into two sub-regions of inner and outer by an auxiliary circular interface. Linear theory is assumed and the eigenfunction expansion approach is used to determine the wave field. In order to examine the validity of the theoretical model, the analytical solutions are compared to agree well with published results with the same parameters. Numerical results including wave amplitude, surge pressure, and wave force are presented with different model parameters. The major factors including wave parameters, structure configuration, and water depth that affect the surge pressure, wave forces, and wave amplitudes are discussed and illustrated by some graphs and cloud maps.

Miniature tunable Airy beam optical meta-device

Tunable Airy beams with controllable propagation trajectories have sparked interest in various fields,such as optical manipulation and laser fabrication.Existing research approaches encounter challenges related to insufficient compactness and integration feasibility,or they require enhanced tunability to enable real-time dynamic manipulation of the propagation trajectory.In this work,we present a novel method that utilizes a dual metasurface system to surpass these limitations,significantly enhancing the practical potential of the Airy beam.Our approach involves encoding a cubic phase profile and two off-axis Fresnel lens phase profiles across the two metasurfaces.The validity of the proposed strategy has been confirmed through simulation and experimental results.The proposed meta-device addresses the existing limitations and lays the foundation for broadening the applicability of Airy beams across diverse domains,encompassing light-sheet microscopy,laser fabrication,optical tweezers,etc.

Fully automatic AI segmentation of oral surgery-related tissues based on cone beam computed tomography images

Accurate segmentation of oral surgery-related tissues from cone beam computed tomography(CBCT)images can significantly accelerate treatment planning and improve surgical accuracy.In this paper,we propose a fully automated tissue segmentation system for dental implant surgery.Specifically,we propose an image preprocessing method based on data distribution histograms,which can adaptively process CBCT images with different parameters.Based on this,we use the bone segmentation network to obtain the segmentation results of alveolar bone,teeth,and maxillary sinus.We use the tooth and mandibular regions as the ROI regions of tooth segmentation and mandibular nerve tube segmentation to achieve the corresponding tasks.The tooth segmentation results can obtain the order information of the dentition.The corresponding experimental results show that our method can achieve higher segmentation accuracy and efficiency compared to existing methods.Its average Dice scores on the tooth,alveolar bone,maxillary sinus,and mandibular canal segmentation tasks were 96.5%,95.4%,93.6%,and 94.8%,respectively.These results demonstrate that it can accelerate the development of digital dentistry.

A DECAGONAL QUASICRYSTAL WITH AN ARC-SHAPED CRACK

A decagonal quasicrystal, which is weakened by an arc-shaped crackpenetrating through the solid in the period direction, and which is subjected to remote uniformphonon stresses, is investigated by applying the complex variable method which is just developed bythe authors. It is found that the phonon and phason stresses near the crack tips exhibit inversesquare root singularities. The four complex stress functions characterizing the phonon and phasonfields are derived. Explicit expressions for the phonon and phason stress intensity factors, crackopening displacements and energy release rate are also presented.

Determination of Wind Pressure Coefficients for Arc-Shaped Canopy Roof with Numerical Wind Tunnel Method

In this paper,the wind load on an arc-shaped canopy roof was studied with numerical wind tunnel method(NWTM) .Three-dimensional models were set up for the canopy roof with opened or closed skylights.The air flow around the roof under wind action from three directions was analysed respectively.Wind pressure coefficients on the canopy roof were determined by NWTM.The results of NWTM agreed well with those of wind tunnel test for the roof with opened skylights,which verified the applicability and rationality of NWTM.The effect of the closure of skylights was then investigated with NWTM.It was concluded that the closure of the skylights may increase the wind suction on the top surface of the roof greatly and should be considered in the structure design of the canopy roof.

Properties of focused Laguerre–Gaussian beam propagating in anisotropic ocean turbulence

We analyze the properties of a focused Laguerre–Gaussian(LG)beam propagating through anisotropic ocean turbulence based on the Huygens–Fresnel principle.Under the Rytov approximation theory,we derive the analytical formula of the channel capacity of the focused LG beam in the anisotropic ocean turbulence,and analyze the relationship between the capacity and the light source parameters as well as the turbulent ocean parameters.It is found that the focusing mirror can greatly enhance the channel capacity of the system at the geometric focal plane in oceanic turbulence.The results also demonstrate that the communication link can obtain high channel capacity by adopting longer beam wavelength,greater initial beam waist radius,and larger number of transmission channels.Further,the capacity of the system increases with the decrease of the mean squared temperature dissipation rate,temperature-salinity contribution ratio and turbulence outer scale factor,and with the increase of the kinetic energy dissipation rate per unit mass of fluid,turbulence inner scale factor and anisotropy factor.Compared to a Hankel–Bessel beam with diffraction-free characteristics and unfocused LG beam,the focused LG beam shows superior anti-turbulence interference properties,which provide a theoretical reference for research and development of underwater optical communication links using focused LG beams.

Generation of structured light beams with polarization variation along arbitrary spatial trajectories using tri-layer metasurfaces

Conventionally,the spatially structured light beams produced by metasurfaces primarily highlight the polarization modulation of the beams propagating along the optical axis or the beams'spatial transmission trajectory.In particular,along the optical axis,the polarization state is either constant or varies continuously in each output plane.Here,we develop innovative spatially structured light beams with continually changing polarization along any arbitrary spatial transmission trajectories.With tri-layer metallic metasurfaces,the geometric characteristics of each layer structure can be adjusted to modulate the phase and polarization state of the incident terahertz(THz)wave.The beam will converge to the predefined trajectory along several paths to generate a Bessel-like beam with longitudinal polarization changes.We demonstrate the versatility of the approach by designing two THz-band structured light beams with varying polarization states along the spatial helical transmission trajectory.Continuous linear polarization changes and linear polarization to right circular polarization(RCP)and back to linear polarization changes are realized respectively.The experimental results are basically consistent with the simulated results.Our proposal for arbitrary trajectory structured light beams with longitudinally varying polarization offers a practical method for continuously regulating the characteristics of spatial structured light beams with non-axial transmission.This technique has potential uses in optical encryption,particle manipulation,and biomedical imaging.

Development of a high-repetition-rate lumped-inductance kicker magnet prototype for the beam switchyard of SHINE

The Shanghai high-repetition-rate X-ray free-electron laser and extreme light facility(SHINE)operates at a maximum repetition rate of 1 MHz.Kicker magnets are key components that distribute electron bunches into three different undulator lines in a bunch-by-bunch mode.The kicker field width must be less than the time interval between bunches.A lumpedinductance kicker prototype was developed using a vacuum chamber with a single-turn coil.The full magnetic field strength was 0.005 T.This paper presents the requirements,design considerations,design parameters,magnetic field calculations,and measurements of the kicker magnets.The relevant experimental results are also presented.The pulse width of the magnetic field was approximately 600 ns,and the maximum operation repetition rate was 1 MHz.The developed kicker satisfies the requirements for the SHINE project.Finally,numerous recommendations for the future optimization of kicker magnets are provided.

Development of in situ characterization techniques in molecular beam epitaxy

Ex situ characterization techniques in molecular beam epitaxy(MBE)have inherent limitations,such as being prone to sample contamination and unstable surfaces during sample transfer from the MBE chamber.In recent years,the need for improved accuracy and reliability in measurement has driven the increasing adoption of in situ characterization techniques.These techniques,such as reflection high-energy electron diffraction,scanning tunneling microscopy,and X-ray photoelectron spectroscopy,allow direct observation of film growth processes in real time without exposing the sample to air,hence offering insights into the growth mechanisms of epitaxial films with controlled properties.By combining multiple in situ characterization techniques with MBE,researchers can better understand film growth processes,realizing novel materials with customized properties and extensive applications.This review aims to overview the benefits and achievements of in situ characterization techniques in MBE and their applications for material science research.In addition,through further analysis of these techniques regarding their challenges and potential solutions,particularly highlighting the assistance of machine learning to correlate in situ characterization with other material information,we hope to provide a guideline for future efforts in the development of novel monitoring and control schemes for MBE growth processes with improved material properties.

Co-doped BaFe_(2)As_(2) Josephson junction fabricated with a focused helium ion beam

Josephson junction plays a key role not only in studying the basic physics of unconventional iron-based superconductors but also in realizing practical application of thin-film based devices,therefore the preparation of high-quality iron pnictide Josephson junctions is of great importance.In this work,we have successfully fabricated Josephson junctions from Co-doped BaFe_(2)As_(2)thin films using a direct junction fabrication technique which utilizes high energy focused helium ion beam(FHIB).The electrical transport properties were investigated for junctions fabricated with various He^(+)irradiation doses.The junctions show sharp superconducting transition around 24 K with a narrow transition width of 2.5 K,and a dose correlated foot-structure resistance which corresponds to the effective tuning of junction properties by He^(+)irradiation.Significant J_c suppression by more than two orders of magnitude can be achieved by increasing the He^(+)irradiation dose,which is advantageous for the realization of low noise ion pnictide thin film devices.Clear Shapiro steps are observed under 10 GHz microwave irradiation.The above results demonstrate the successful fabrication of high quality and controllable Co-doped BaFe_(2)As_(2)Josephson junction with high reproducibility using the FHIB technique,laying the foundation for future investigating the mechanism of iron-based superconductors,and also the further implementation in various superconducting electronic devices.

Unraveling the efficacy network: A network meta-analysis of adjuvant external beam radiation therapy methods after hepatectomy

BACKGROUND Primary liver cancer is a malignant tumor with a high recurrence rate that significantly affects patient prognosis.Postoperative adjuvant external radiation therapy(RT)has been shown to effectively prevent recurrence after liver cancer resection.However,there are multiple RT techniques available,and the differ-ential effects of these techniques in preventing postoperative liver cancer re-currence require further investigation.AIM To assess the advantages and disadvantages of various adjuvant external RT methods after liver resection based on overall survival(OS)and disease-free survival(DFS)and to determine the optimal strategy.METHODS This study involved network meta-analyses and followed the PRISMA guidelines.The data of qualified studies published before July 10,2023,were collected from PubMed,Embase,the Web of Science,and the Cochrane Library.We included relevant studies on postoperative external beam RT after liver resection that had OS and DFS as the primary endpoints.The magnitudes of the effects were determined using risk ratios with 95%confidential intervals.The results were analyzed using R software and STATA software.RESULTS A total of 12 studies,including 1265 patients with hepatocellular carcinoma(HCC)after liver resection,were included in this study.There was no significant heterogeneity in the direct paired comparisons,and there were no significant differences in the inclusion or exclusion criteria,intervention measures,or outcome indicators,meeting the assumptions of heterogeneity and transitivity.OS analysis revealed that patients who underwent stereotactic body radiotherapy(SBRT)after resection had longer OS than those who underwent intensity modulated radiotherapy(IMRT)or 3-dimensional conformal RT(3D-CRT).DFS analysis revealed that patients who underwent 3D-CRT after resection had the longest DFS.Patients who underwent IMRT after resection had longer OS than those who underwent 3D-CRT and longer DFS than those who underwent SBRT.CONCLUSION HCC patients who undergo liver cancer resection must consider distinct advantages and disadvantages when choosing between SBRT and 3D-CRT.IMRT,a RT technique that is associated with longer OS than 3D-CRT and longer DFS than SBRT,may be a preferred option.

Beam Training and Tracking in mmWave Communication:A Survey

Communicating on millimeter wave(mmWave)bands is ushering in a new epoch of mobile communication which provides the availability of 10 Gbps high data rate transmission.However,mmWave links are easily prone to short transmission range communication because of the serious free space path loss and the blockage by obstacles.To overcome these challenges,highly directional beams are exploited to achieve robust links by hybrid beamforming.Accurately aligning the transmitter and receiver beams,i.e.beam training,is vitally important to high data rate transmission.However,it may cause huge overhead which has negative effects on initial access,handover,and tracking.Besides,the mobility patterns of users are complicated and dynamic,which may cause tracking error and large tracking latency.An efficient beam tracking method has a positive effect on sustaining robust links.This article provides an overview of the beam training and tracking technologies on mmWave bands and reveals the insights for future research in the 6th Generation(6G)mobile network.Especially,some open research problems are proposed to realize fast,accurate,and robust beam training and tracking.We hope that this survey provides guidelines for the researchers in the area of mmWave communications.