The study on the fluid flow, meniscus oscillation, slag entrapment in continuous casting mould was conducted mathematically and experimentally. The results show that the injection of argon into submerged nozzle enhan...The study on the fluid flow, meniscus oscillation, slag entrapment in continuous casting mould was conducted mathematically and experimentally. The results show that the injection of argon into submerged nozzle enhances the meniscus oscillation, thus increases the probability of slag entrapment, and the critical argon blowing flow rate, which will give rise to slag entrapment, is around 10l/min. The trajectory of bubble is affected by the bubble diameter and the molten steel flow, and the bubble diameter is dominant. The bubble with diameter 1.4mm floats fastest with 0.47m/s terminal velocity.展开更多
An improved self-consistent, multi-component, and one-dimensional plasma model for simulating atmospheric pressure argon glow discharge is presented. In the model, both the plasma hydrodynamics model and chemical mode...An improved self-consistent, multi-component, and one-dimensional plasma model for simulating atmospheric pressure argon glow discharge is presented. In the model, both the plasma hydrodynamics model and chemical model are considered. The numerical simulation is carried out for parallel-plate geometry with a separation of 0.06 cm. The results show that Ar＊ plays a major role in the discharge, which is mainly produced by ground state excitation reaction. The electron temperature reaches its maximum in the cathode sheath but maintains a low value （0.23 eV） in bulk plasma. Elastic collision is the dominant volumetric electron energy loss in atmosphere argon glow discharge, which is negligible in low pressure argon glow discharge. The metastable step-wise ionization is the main mechanism for electron production to sustain the discharge. However, the highest contribution to electron production rate is ground state ionization reaction. The bremsstrahlung power density is related to electric voltage. With the increase of the electric voltage, the bremsstrahlung power density increases, namely, the strength of ultraviolet radiation spectrum enhances in the cathode sheath.展开更多
The dominant process in relaxation of DC glow discharge between two plane parallel electrodes in argon at pressure 200 Pa is analyzed by measuring the breakdown time delay and by analytical and numerical models. By us...The dominant process in relaxation of DC glow discharge between two plane parallel electrodes in argon at pressure 200 Pa is analyzed by measuring the breakdown time delay and by analytical and numerical models. By using the approx- imate analytical model it is found that the relaxation in a range from 20 to 60 ms in afterglow is dominated by Ar＋ ions, produced by atomic-to-molecular conversion of Ar＋ ions in the first several milliseconds after the cessation of the discharge. This conversion is confirmed by the presence of double-Gaussian distribution for the formative time delay, as well as con- version maxima in a set of memory curves measured in different conditions. Finally, the numerical one-dimensional （1D） model for determining the number densities of dominant particles in stationary DC glow discharge and two-dimensional （2D） model for the relaxation are used to confirm the previous assumptions and to determine the corresponding collision and transport coefficients of dominant species and processes.展开更多
Targeting the single tuyere and double tuyere methods of argon blowing for Baosteel＇ s 300 t ladle furnace, the 3D continuity equation, the N-S equation and the turbulent k-ε double-equation were used to model the f...Targeting the single tuyere and double tuyere methods of argon blowing for Baosteel＇ s 300 t ladle furnace, the 3D continuity equation, the N-S equation and the turbulent k-ε double-equation were used to model the form of the molten steel flow and the dead areas under six different argon blowing conditions. The different flow field forms and the degree of mixing under different argon blowing methods were compared. The results demonstrate that when large ladles are operated via different methods of argon blowing, the spray from the centre of a single tuyere forms a symmetrical vortex, while when a double tuyere sprays, there is basically no clear vortex. In regards to the amount of argon blowing that will produce the best blend of molten steel, the amount of dead area reduction will not be clearly noticeable if there is an excessive argon blowing amount.展开更多
以国内某钢厂150 t LF为原型,通过水模型实验,对钢包原吹氩位置的合理性进行了分析和探讨,对双孔底吹不同底透气砖布置条件下钢包内的搅拌混合行为进行了研究,提出了该厂LF较佳底吹气搅拌位置及吹氩制度,并考察了有顶渣情况下的液面隆...以国内某钢厂150 t LF为原型,通过水模型实验,对钢包原吹氩位置的合理性进行了分析和探讨,对双孔底吹不同底透气砖布置条件下钢包内的搅拌混合行为进行了研究,提出了该厂LF较佳底吹气搅拌位置及吹氩制度,并考察了有顶渣情况下的液面隆起的变化规律.展开更多
文摘The study on the fluid flow, meniscus oscillation, slag entrapment in continuous casting mould was conducted mathematically and experimentally. The results show that the injection of argon into submerged nozzle enhances the meniscus oscillation, thus increases the probability of slag entrapment, and the critical argon blowing flow rate, which will give rise to slag entrapment, is around 10l/min. The trajectory of bubble is affected by the bubble diameter and the molten steel flow, and the bubble diameter is dominant. The bubble with diameter 1.4mm floats fastest with 0.47m/s terminal velocity.
基金supported by the Major State Basic Research Development Program of China (973 Program) (No. 2011CB20941)Scientific Research Foundation of State Key Lab. of Power Transmission Equipment and System Security of China (No. 2007DA10512709102)+1 种基金National Natural Science Foundation of China (No. 51007096)the Fundamental Research Funds for the Central Universities of China(No. CDJZR10150001)
文摘An improved self-consistent, multi-component, and one-dimensional plasma model for simulating atmospheric pressure argon glow discharge is presented. In the model, both the plasma hydrodynamics model and chemical model are considered. The numerical simulation is carried out for parallel-plate geometry with a separation of 0.06 cm. The results show that Ar＊ plays a major role in the discharge, which is mainly produced by ground state excitation reaction. The electron temperature reaches its maximum in the cathode sheath but maintains a low value （0.23 eV） in bulk plasma. Elastic collision is the dominant volumetric electron energy loss in atmosphere argon glow discharge, which is negligible in low pressure argon glow discharge. The metastable step-wise ionization is the main mechanism for electron production to sustain the discharge. However, the highest contribution to electron production rate is ground state ionization reaction. The bremsstrahlung power density is related to electric voltage. With the increase of the electric voltage, the bremsstrahlung power density increases, namely, the strength of ultraviolet radiation spectrum enhances in the cathode sheath.
基金supported by the Ministry of Education,Science and Technological Development of the Republic of Serbia(Grant No.ON171025)
文摘The dominant process in relaxation of DC glow discharge between two plane parallel electrodes in argon at pressure 200 Pa is analyzed by measuring the breakdown time delay and by analytical and numerical models. By using the approx- imate analytical model it is found that the relaxation in a range from 20 to 60 ms in afterglow is dominated by Ar＋ ions, produced by atomic-to-molecular conversion of Ar＋ ions in the first several milliseconds after the cessation of the discharge. This conversion is confirmed by the presence of double-Gaussian distribution for the formative time delay, as well as con- version maxima in a set of memory curves measured in different conditions. Finally, the numerical one-dimensional （1D） model for determining the number densities of dominant particles in stationary DC glow discharge and two-dimensional （2D） model for the relaxation are used to confirm the previous assumptions and to determine the corresponding collision and transport coefficients of dominant species and processes.
文摘Targeting the single tuyere and double tuyere methods of argon blowing for Baosteel＇ s 300 t ladle furnace, the 3D continuity equation, the N-S equation and the turbulent k-ε double-equation were used to model the form of the molten steel flow and the dead areas under six different argon blowing conditions. The different flow field forms and the degree of mixing under different argon blowing methods were compared. The results demonstrate that when large ladles are operated via different methods of argon blowing, the spray from the centre of a single tuyere forms a symmetrical vortex, while when a double tuyere sprays, there is basically no clear vortex. In regards to the amount of argon blowing that will produce the best blend of molten steel, the amount of dead area reduction will not be clearly noticeable if there is an excessive argon blowing amount.
