Finite-Element Analysis of Parts Stress State of Tight Joint Assembled by Press Fitting

This paper includes descriptions of the stress distribution regularities in the tight joint parts, regularities of the stress state changes in the contact region along coupling length, stress concentration factors, levels of additional stresses caused by press fitting. Distributions of stress intensity, axial stress, contact pressure, tangent stress in parts and in contact zone along coupling length are considered. Calculation results obtained by three approaches: Lame relationships, FEM without considering assembly method, FEM with considering press fitting process are analyzed and compared. The adequacy of research carried out is confirmed.

Optimization of Fixture Number in Large Thin-Walled Parts Assembly Based on IPSO

There are lots of researches on fixture layout optimization for large thin-walled parts.Current researches focus on the positioning problem,i.e.,optimizing the positions of a constant number of fixtures.However,how to determine the number of fixtures is ignored.In most cases,the number of fixtures located on large thin-walled parts is determined based on engineering experience,which leads to huge fixture number and extra waste.Therefore,this paper constructs an optimization model to minimize the number of fixtures.The constraints are set in the optimization model to ensure that the part deformation is within the surface profile tolerance.In addition,the assembly gap between two parts is also controlled.To conduct the optimization,this paper develops an improved particle swarm optimization(IPSO)algorithm by integrating the shrinkage factor and adaptive inertia weight.In the algorithm,particles are encoded according to the fixture position.Each dimension of the particle is assigned to a sub-region by constraining the optional position range of each fixture to improve the optimization efficiency.Finally,a case study on ship curved panel assembly is provided to prove that our method can optimize the number of fixtures while meeting the assembly quality requirements.This research proposes a method to optimize the number of fixtures,which can reduce the number of fixtures and achieve deformation control at the same time.

Performance Characterization of CR/PU Asphalt for Potential Application in Assembled Fast-Repairing Engineering

Conventional repairing methods for asphalt pavement have some inconveniences,such as insufficient strength,and are typically time-consuming.To address these issues,this study proposes a new technological method to design and prepare a high-performance assembled asphalt concrete block for fast repair of the potholes.A series of composite modified asphalt binders with 10%crumb rubber(CR)and different dosages(0%,1%,3%,5%)of polyurethane(PU)are examined to determine the optimized binder.Subsequently,the corresponding asphalt mixtures are prepared for further comparison and assessment of engineering properties,such as moistureinduced damage,high-temperature deformation,and low-temperature cracking characteristics.The test results show that PU can significantly improve the high-temperature performance and hardness of(crumb rubber modified asphalt)CRMA binder;3%PU contributes allowing the resistance of CRMA mixture to moisture-induced damage at higher levels,particularly under water whole immersion;as 3%PU is added,the high-temperature rutting deformation resistance of the CRMA mixture increases significantly,and the low-temperature anti-cracking properties are also improved slightly.Therefore,the innovatively designed high-quality assembled fast-repairing asphalt concrete block is recommended as an appropriate option for highway maintenance.

Development of Fixture Layout Optimization for Thin-Walled Parts:A Review

An increasing number of researchers have researched fixture layout optimization for thin-walled part assembly during the past decades.However,few papers systematically review these researches.By analyzing existing literature,this paper summarizes the process of fixture layout optimization and the methods applied.The process of optimization is made up of optimization objective setting,assembly variation/deformation modeling,and fixture layout optimization.This paper makes a review of the fixture layout for thin-walled parts according to these three steps.First,two different kinds of optimization objectives are introduced.Researchers usually consider in-plane variations or out-of-plane deformations when designing objectives.Then,modeling methods for assembly variation and deformation are divided into two categories:Mechanism-based and data-based methods.Several common methods are discussed respectively.After that,optimization algorithms are reviewed systematically.There are two kinds of optimization algorithms:Traditional nonlinear programming and heuristic algorithms.Finally,discussions on the current situation are provided.The research direction of fixture layout optimization in the future is discussed from three aspects:Objective setting,improving modeling accuracy and optimization algorithms.Also,a new research point for fixture layout optimization is discussed.This paper systematically reviews the research on fixture layout optimization for thin-walled parts,and provides a reference for future research in this field.

Numerical Simulation-Based Analysis of the Impact of Overloading on Segmentally Assembled Bridges

Segmentally assembled bridges are increasinglyfinding engineering applications in recent years due to their unique advantages,especially as urban viaducts.Vehicle loads are one of the most important variable loads acting on bridge structures.Accordingly,the influence of overloaded vehicles on existing assembled bridge structures is an urgent concern at present.This paper establishes thefinite element model of the segmentally assembled bridge based on ABAQUS software and analyzes the influence of vehicle overload on an assembled girder bridge struc-ture.First,afinite element model corresponding to the target bridge is established based on ABAQUS software,and the load is controlled to simulate vehicle movement in each area of the traveling zone at different times.Sec-ond,the key cross-sections of segmental girder bridges are monitored in real time based on the force character-istics of continuous girder bridges,and they are compared with the simulation results.Finally,a material damage ontology model is introduced,and the structural damage caused by different overloading rates is compared and analyzed.Results show that thefinite element modeling method is accurate by comparing with on-site measured data,and it is suitable for the numerical simulation of segmental girder bridges;Dynamic sensors installed at 1/4L,1/2L,and 3/4L of the segmental girder main beams could be used to identify the dynamic response of segmental girder bridges;The bottom plate of the segmental girder bridge is mostly damaged at the position where the length of the precast beam section changes and the midspan position.With the increase in load,damage in the direction of the bridge develops faster than that in the direction of the transverse bridge.Thefindings of this study can guide maintenance departments in the management and maintenance of bridges and vehicles.

Application Strategies of Modular Design in Assembled Teaching Buildings

As an efficient,environmentally friendly,energy-saving construction method,assembled buildings are now widely used in campus building construction.Modular design thinking is system-based design thinking,and its application to the design of an assembled teaching building project will comprehensively improve the rationality of the teaching building and component design.The paper focuses on the application of modular design thinking in assembled teaching building design,aiming to provide references for China’s architectural design units,giving full play to the advantages of modular design thinking in future teaching building design projects,and enhancing the level of design,for the construction of the teaching building and the basis of the technical guarantee.

In vitro corrosion and antibacterial properties of layer-by-layer assembled GS/PSS coating on AZ31 magnesium alloys

To enhance the corrosion resistance of magnesium（Mg） alloy and to impart its surface with antibacterial functionality for inhibiting biofilm formation and biocorrosion, Mg（OH）2 films were fabricated on AZ31 magnesium alloy substrates by an in-situ hydrothermal method and well-defined multilayer coatings, consisting of gentamicin sulfate（GS） and poly（sodium 4-styrene sulfonate）（PSS）, were prepared via layer-by-layer（Lb L） assembly. The morphologies, chemical compositions and corrosion resistance of the obtained（PSS/GS）n/Mg sample were investigated using scanning electron microscopy, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, electrochemical methods and immersion tests. Finally, the bactericidal activity of（PSS/GS）n/Mg samples against Staphylococcus aureus was assessed by the zone of inhibition methods and plate-counting method. The so-synthesized composite coating on the Mg alloy substrates exhibits good corrosion resistance and antibacterial performance, which make them attractive as coatings for medical implanted devices.

In vitro corrosion resistance and antibacterial properties of layer-by-layer assembled chitosan/poly-L-glutamic acid coating on AZ31 magnesium alloys

Surface functionalization of magnesium(Mg)alloys is desired to obtain the surfaces with both improved corrosion resistance and antibacterial property.A corrosion-resistant and antimicrobial coating was prepared on Mg alloy surface by layer-by-layer(LbL)assembly of chitosan(CHI)and poly-L-glutamic acid(PGA)by electrostatic attraction.The functionalized surfaces of the Mg alloys were characterized by field-emission scanning electron microscopy(FE-SEM),Fourier transform infrared(FT-IR)spectroscopy and electrochemical tests.The bactericidal activity of the samples against Staphylococcus aureus was assessed by the zone of plate-counting method.The obtained coating on the Mg alloy substrates exhibits good corrosion resistance and antibacterial performance.

In vitro corrosion resistance,antibacterial activity and cytocompatibility of a layer-by-layer assembled DNA coating on magnesium alloy

A chitosan/deoxyribonucleic acid(CHI/DNA)_(5)coating was constructed by layer-by-layer(LbL)assembly dip coating method with Mg(OH)_(2)coating as an inner protective layer on AZ31 alloy.X-ray diffractometry,X-ray photoelectron spectrometry,Fourier transform infrared spectroscopy and field-emission scanning electron microscopy were utilized to represent the chemical compositions and surface morphologies of the coatings.Electrochemical tests and hydrogen evolution measurements were implemented to confirm the good corrosion resistance of the composite coating in artificial body fluid.Antimicrobial activity of the composite coatings was tested via the plate-counting method,and the cytotoxicity of the samples was appraised by MTT assay and Live/dead staining.A double action was put into effect for the composite coating,which the inner Mg(OH)2 coating plays the part of physical barrier,and the outer(CHI/DNA)5 coating is employed as an inducer to fabricate a biocompatible Ca-P corrosion product coating during immersion,making up for its thin thickness.Otherwise,the composite coating is also beneficial for the growth of bone,resulting from the biomineralization effect of the outer polyelectrolyte multilayer.The good antibacterial property of the(CHI/DNA)5/Mg(OH)2 coating is ascribed to the contact-killing strength of CHI.Thus,the obtained(CHI/DNA)5/Mg(OH)2 coating has a wide application prospect in the field of Mg-based bone implantation.

Numerical simulation analysis for deformation deviation and experimental verification for an antenna thin-wall parts considering riveting assembly with finite element method

In the process of thin-wall parts assembly for an antenna,the parts assembly deformation deviation is occurring due to the riveting assembly.In view of the riveting assembly deformation problems,it can be analyzed through transient and static simulation.In this work,the theoretical deformation model for riveting assembly is established with round head rivet.The simulation analysis for riveting deformation is carried out with the riveting assembly piece including four rivets,which comparing with the measuring points experiment results of riveting test piece through dealing with the experimental data using the point coordinate transform method and the space line fitting method.Simultaneously,the deformation deviation of the overall thin-wall parts assembly structure is analyzed through finite element simulation;and its results are verified by the measuring experiment for riveting assembly with the deformation deviation of some key points on the thin-wall parts.Through the comparison analysis,it is shown that the simulation results agree well with the experimental results,which proves the correctness and effectiveness of the theoretical analysis,simulation results and the given experiment data processing method.Through the study on the riveting assembly for thin-wall parts,it will provide a theoretical foundation for improving thin-wall parts assembly quality of large antenna in future.

Thermal analysis of an LED module with a novelly assembled heat pipe heat sink

This work aims to improve the thermal performance of a light emitting diode(LED) module by employing a novelly assembled heat pipe heat sink. The heat pipe was embedded into the heat sink by a phase change expansion assembly(PCEA) process, which was developed by both finite element(FE) analysis and experiments. Heat transfer performance and optical performance of the LED modules were experimentally investigated and discussed. Compared to the LED module with a traditionally assembled heat pipe heat sink, the LED module employing the PCEA process exhibits about 20% decrease in the thermal resistance from the MCPCB to the heat pipe. The junction temperature is 4% lower and the luminous flux is 2% higher. The improvement in the thermal and optical performance is important to the high power LED applications.

Room-Temperature Assembled MXene-Based Aerogels for High Mass-Loading Sodium-Ion Storage

Low-temperature assembly of MXene nanosheets into three-dimensional(3D) robust aerogels addresses the crucial stability concern of the nano-building blocks during the fabrication process,which is of key importance for transforming the fascinating properties at the nanoscale into the macroscopic scale for practical applications.Herein,suitable cross-linking agents(amino-propyltriethoxysilane,Mn^(2+),Fe^(2+),Zn^(2+),and Co^(2+)) as interfacial mediators to engineer the interlayer interactions are reported to realize the graphene oxide(GO)-assisted assembly of Ti_(3)C_(2)T_(x) MXene aerogel at room temperature.This elaborate aerogel construction not only suppresses the oxidation degradation of Ti_(3)C_(2)T_(x) but also generates porous aerogels with a high Ti_(3)C_(2)T_(x) content(87 wt%) and robustness,thereby guaranteeing the functional accessibility of Ti_(3)C_(2)T_(x) nanosheets and operational reliability as integrated functional materials.In combination with a further sulfur modification,the Ti_(3)C_(2)T_(x) aerogel electrode shows promising electrochemical performances as the freestanding anode for sodium-ion storage.Even at an ultrahigh loading mass of 12.3 mg cm^(-2),a pronounced areal capacity of 1.26 mAh cm^(-2) at a current density of 0.1 A g^(-1) has been achieved,which is of practical significance.This work conceptually suggests a new way to exert the utmost surface functionalities of MXenes in 3D monolithic form and can be an inspiring scaffold to promote the application of MXenes in different areas.

Novel Kriging-Based Decomposed-Coordinated Approach for Estimating the Clearance Reliability of Assembled Structures

Turbine blisks are assembled using blades,disks and casings.They can endure complex loads at a high temperature,high pressure and high speed.The safe operation of assembled structures depends on the reliability of each component.Monte Carlo(MC)simulation is commonly used to analyze structural reliability,but this method needs to run thousands of computations.In order to assess the clearance reliability of assembled structures in an efficient and precise manner,the novel Kriging-based decomposed-coordinated(DC)(DCNK)approach is proposed by integrating the DC strategy,the Kriging model and the importance sampling-based Markov chain(MCIS)technique.In this method,the DC strategy is used to decompose a multi-objective problem into many single-objective problems.The relationships between these many single-objectives and the overall objective are then coordinated.The Kriging model is applied to establish the limit state functions of the single-objectives and multi-objective problems,while the MCIS method is used to assess the structural assembled clearance reliability.Moreover,a highly nonlinear complex compound function is first utilized to verify the DCNK model from a mathematical perspective.Then,the reliability of an aeroengine high-pressure turbine(HPT)blade-tip radial running clearance(BTRRC)is analyzed to validate the DCNK approach by considering thermo-structural interaction.The analytical results show that the reliability is 0.9976 when the allowance value of the BTTRC is 1.7650×10^(−3)m.Compared with different methodologies(including direct simulation,the classical Kriging model,and the weighted response surface method(WRSM)),the proposed method holds obvious advantages in computing time and precision,as well as simulation efficiency and precision.The efforts of this paper provide a useful approach to analyzing assembled clearance reliability and contribute to the development of structural reliability theory.

Green manuring facilitates bacterial community dispersal across different compartments of subsequent tobacco

Green manure–crop rotation is a sustainable approach to protect crops against diseases and improve yield.However,the mechanism by which green manuring manipulates the crop-associated microbial community remains to be elucidated.In this study,we explored the horizontal processes of bacterial communities in different compartments of the soil–root interface(bulk soil,rhizosphere soil,rhizoplane and endosphere)of tobacco by performing a field experiment including four rotation practices,namely,tobacco rotated with smooth vetch,ryegrass,radish,and winter fallow(without green manure).Results showed that the co-occurrence networks constructed by adjacent compartments of the soil–root interface with green manuring had more edges than without green manuring,indicating dramatic microbial interactions.Green manuring increased the dispersal-niche continuum index between bulk soil and other compartments,indicating that it facilitated the horizontal dispersal of microbes.For the different green manuring practices,the neutral community model explained 24.6–27.6%of detection frequency for bacteria,and at least one compartment under each practice had a normalized stochasticity ratio higher than the 50%boundary point,suggesting that the deterministic and stochastic processes jointly shaped the tobacco microbiome.In conclusion,green manuring generally facilitates bacterial community dispersal across different compartments and enhances potential interactions among adjacent compartments.This study provides empirical evidence for understanding the microbiome assembly under green manure–crop rotation.

Molecular recognition by gold, silver and copper nanoparticles

The intrinsic physical properties of the noble metal nanoparticles,which are highly sensitive to the nature of their local molecular environment,make such systems ideal for the detection of molecular recognition events.The current review describes the state of the art concerning molecular recognition of Noble metal nanoparticles.In the first part the preparation of such nanoparticles is discussed along with methods of capping and stabilization.A brief discussion of the three common methods of functionalization:Electrostatic adsorption;Chemisorption;Affinity-based coordination is given.In the second section a discussion of the optical and electrical properties of nanoparticles is given to aid the reader in understanding the use of such properties in molecular recognition.In the main section the various types of capping agents for molecular recognition;nucleic acid coatings,protein coatings and molecules from the family of supramolecular chemistry are described along with their numerous applications.Emphasis for the nucleic acids is on complementary oligonucleotide and aptamer recognition.For the proteins the recognition properties of antibodies form the core of the section.With respect to the supramolecular systems the cyclodextrins,calix[n]arenes,dendrimers,crown ethers and the cucurbitales are treated in depth.Finally a short section deals with the possible toxicity of the nanoparticles,a concern in public health.

Electrodeposited 3D hierarchical NiFe microflowers assembled from nanosheets robust for the selective electrooxidation of furfuryl alcohol

A robust and green strategy for the selective upgrading of biomass-derived platform chemicals towards highly valuable products is important for the sustainable development.Herein,the efficient electrocatalytic oxidation of biomass-derived furfuryl alcohol(FFA)into furoic acid(FurAc)catalyzed by the electrodeposited non-precious NiFe microflowers was successfully reached under the low temperature and ambient pressure.The 3D hierarchical NiFe microflowers assembled from ultrathin nanosheets were controllably synthesized by the electrodeposition method and uniformly grown on carbon fiber paper(CFP).Electrochemical analysis confirmed that NiFe nanosheets more preferred in the selective oxidation of FFA(FFAOR)than oxygen evolution reaction(OER).The linear sweep voltammetry(LSV)in FFAOR displayed a clear decrease towards lower potential,resulting in 30 mV reduction of overpotential at 20 mA cm^(-2) compared with that of OER.The optimal catalyst Ni_(1)Fe_(2) nanosheets exhibited the highest selectivity of FurAc(94.0%)and 81.4%conversion of FFA within 3 h.Besides,the influence of various reaction parameters on FFAOR was then explored in details.After that,the reaction pathway was investigated and rationally proposed.The outstanding performance for FFAOR can be ascribed to the unique structure of 3D flower-like NiFe nanosheets and oxygen vacancies,resulting in large exposure of active sites,faster electron transfer and enhanced adsorption of reactants.Our findings highlight a facile and convenient mean with a promising green future,which is promising for processing of various biomass-derived platform chemicals into value-added products.

Adjustable Luminescence of SrAl_2O_4:Eu^(2+),Dy ^(3+) Assembled in Zeolite

Capsulating guest into the nanometer voids of zeolites is a effective way to form novel host-guest material. In our work, stoichiometric SrAl2O4 : Eu2+, Dy3+ sol guest was prepared by sol-gel method and assembled into the nanometer channels of zeolite ZSM-5 host through mechanical mixing, hydrothemial reaction and microwave heating reaction, respectively. After being reduced and diffused in a microwave muffle, the fluorescence spectra of the host-guest materials exhibit remarkable blue shifts in companison of that of SrAl2O4 : Eu2+, Dy3+ Some interesting phenomena in the assembled host-guest materials are that the after-low emission spectra exist two bands at about 400 nm and 517 nm and the relative strengths of these two hands can be adjusted by changing the assembly methods and the assembly concentration. These are attributed to the fact that the phosphor was capsuiated into the voids of zeolite ZSM-5 and generated the quantum size effect and the host-guest effect.

Cx31 is assembled and trafficked to cell surface by ER-Golgi pathway and degraded by proteasomal or lysosomal pathways

Gap junctions, consisting of connexins, allow the exchange of small molecules (<1 kD) between adjacent cells, thusproviding a mechanism for synchronizing the responses of groups of cells to environmental stimuli. Connexin 31 is amember of the connexin family. Mutations on connexin 31 are associated with erythrokeratodermia variabilis, hearingimpairment and peripheral neuropathy. However, the pathological mechanism for connexin 31 mutants in these diseasesare still unknown. In this study, we analyzed the assembly, trafficking and metabolism of connexin 31 in HeLa cellsstably expressing connexin 31. Calcein transfer assay showed that calcein transfer was inhibited when cells weretreated with Brefeldin A or cytochalasin D, but not when treated with nocodazole or α-glycyrrhetinic acid, suggestingthat Golgi apparatus and actin filaments, but not microtubules, are crucial to the trafficking and assembly of connexin31, as well as the formation of gap junction intercellular communication by connexin 31. Additionally, α-glycyrrhetinicacid did not effectively inhibit gap junctional intercellular communication formed by connexin 31. Pulse-chase assayrevealed that connexin 31 had a half-life of about 6 h. Moreover, Western blotting and fluorescent staining demonstratedthat in HeLa cells stably expressing connexin 31, the amount of connexin 31 was significantly increased after these cellswere treated with proteasomal or lysosomal inhibitors. These findings indicate that connexin 31 was rapidly renewed,and possibly degraded by both proteasomal and lysosomal pathways.

Preparation of iridium nano-and submicroparticles on solid substrates by direct surface growth and drop-drying assembly

Iridium nanoparticles (IrNPs) and submicroparticles (IrSMPs) with different shapes were synthesized and assembled on indium thin oxide (ITO) and Si substrates using two different methods: direct surface growth and drop-drying assembly. The obtained IrNPs and IrSMPs were characterized using scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). The IrSMPs (or IrNPs) with disc-like shape and irregular shapes were obtained on ITO substrate by direct surface growth method using polyvinylpyrrolidone (PVP) and sodium citrate as different stabilizers, respectively. The reaction time and the injection temperature of reducing agent are found to have great effect on the size and morphology of the surface-grown Ir particles. The disc-like, ellipsoidal, and spherical IrSMPs (or IrNPs) were also synthesized in homogeneous solution in the presence of H3BO3 and Na2B4O7 as assistant-stabilizer. These IrNPs and IrSMPs were used as building blocks to construct nanoparticle assemblies by using a simple drop-drying method. Uniform IrNP and IrSMP assemblies were successfully prepared on Si and ITO substrates, indicating that the drop-drying method is efficient for the preparation of not only nanoparticle assemblies but also submicroparticle assemblies.

RESEARCH ON VIRTUAL-PART-BASED CONNECTING ELEMENT MODELING

Based on the inner character analysis of interpart, detail modification andassembly relation of mechanical connecting element, the idea, which extends the feature modeling ofpart to the interpart feature modeling for assembly purpose, is presented, and virtual-part-basedconnecting element modeling is proposed. During the assembly modeling, base parts are modified bythe Boolean subtraction between the virtual part and the part to be connected. Dynamic matchingalgorithm, which is based on list database, is designed for dynamic extension and off-line editingof connecting part and virtual part, and design rules of connecting element is encapsulated by thevirtual part. A prototyped software module for rapid design of connecting elements is implementedunder self-developed CAD/CAM platform-SuperMan.