A Study on HA Titanium Surface with Atomic Force Microscope (AFM)

Three kinds of titanium surface especially the HA surface are analyzed. Titanium was treated by 3 kinds of methods that were acid ＆ alkali, calcic solution and apathe solution. Samples were observed by optic microscope and atomic force microscope （ AFM ） . The typical surface morphology of the acid and alkali group is little holes, and on the two HA surface the tiny protuberances is typical. The surface treated by apatite solution was smoother than the two formers. The rough surface treated with acid and alkali was propitious to Ca^＋ , P^- and proteins＇ adhesion, and the relatively smooth HA surface was of benefit to the cell adhesion.

IMPROVED FABRICATION METHOD FOR CARBON NANOTUBE PROBE OF ATOMIC FORCE MICROSCOPY(AFM)

An improved arc discharge method is developed to fabricate carbon nanotube probe of atomic force microscopy （AFM） here. First, silicon probe and carbon nanotube are manipulated under an optical microscope by two high precision microtranslators. When silicon probe and carbon nanotube are very close, several tens voltage is applied between them. And carbon nanotube is divided and attached to the end of silicon probe, which mainly due to the arc welding function. Comparing with the arc discharge method before, the new method here needs no coat silicon probe with metal film in advance, which can greatly reduce the fabrication＇s difficulty. The fabricated carbon nanotube probe shows good property of higher aspect ratio and can more accurately reflect the true topography of silicon grating than silicon probe. Under the same image drive force, carbon nanotube probe had less indentation depth on soft triblock copolymer sample than silicon probe. This showed that carbon nanotube probe has lower spring constant and less damage to the scan sample than silicon probe.

MICRO/NANO-MACHINING ON SILICON SURFACE WITH A MODIFIED ATOMIC FORCE MICROSCOPE

To understand the deformation and removal mechanism of material on nano-scale at ultralow loads,a systemic study on AFM micro/nano-machining on single crystal ailicon is conducted. The results indicate that AFM nano- machining has a precisely dimensional controllability and a good surface quality on nanometer scale.A SEM is adopted to observe nano-machined region and chips,the results indicate that the material removal mechanisms change with the applied normal load. An XPS is used to analyze the changes of chemical composition inside and outside the nano-machined region respectively.The nano-indentation which is conducted with the same AFM diamond tip on the machined region shows a big discrepancy compared with that on the macro-scale. The calculated results show higher nano-hardness and elastic modulus than normal values .This phenomenon on be regarded as the indentation size effect(ISE).

Nonlinear control techniques for an atomic force microscope system

Two nonlinear control techniques are proposed for an atomic force microscopesystem. Initially, a learning-based control algorithm is developed for the microcantilever-samplesystem that achieves asymptotic cantilever tip tracking for periodic trajectories. Specifically, thecontrol approach utilizes a learning-based feedforward term to compensate for periodic dynamics andhigh-gain terms to account for non-periodic dynamics. An adaptive control algorithm is thendeveloped to achieve asymptotic cantilever tip tracking for bounded tip trajectories despiteuncertainty throughout the system parameters. Simulation results are provided to illustrate theefficacy and performance of the control strategies.

Surface Electromechanical Coupling on DLC Film with Conductive Atomic Force Microscope

Diamond-like carbon (DLC) film composed of microscopically insulation but microscopically a mixture of conducting (sp2) and insulating (sp3) phases was discussed on the local modification with a conductive atomic force microscope (C-APM). Especially, a topographic change was observed when a direct current (DC) bias-voltage was applied to the DLC film. Experimental results show that a nanoscale pit on DLC surface was formed when applying a positive 25 V on DLC film. According to the interacting force between CoCr-coated microelectronic scanning probe (MESP) tip and DLC surface, as well as the Sondheimer oscillation theory, the 'scalewing effect' of the pit was explained. Electromechanical coupling on DLC film suggested that the depth of pits increased with an increase of load applied to surface when the cantilever-deflected signal was less than a certain threshold voltage.

Sorting Gold and Sand(Silica) Using Atomic Force Microscope-Based Dielectrophoresis

Additive manufacturing-also known as 3D printing-has attracted much attention in recent years as a powerful method for the simple and versatile fabrication of complicated three-dimensional structures.However,the current technology still exhibits a limitation in realizing the selective deposition and sorting of various materials contained in the same reservoir,which can contribute significantly to additive printing or manufacturing by enabling simultaneous sorting and deposition of different substances through a single nozzle.Here,we propose a dielectrophoresis(DEP)-based material-selective deposition and sorting technique using a pipette-based quartz tuning fork(QTF)-atomic force microscope(AFM) platform DEPQA and demonstrate multi-material sorting through a single nozzle in ambient conditions.We used Au and silica nanoparticles for sorting and obtained 95% accuracy for spatial separation,which confirmed the surfaceenhanced Raman spectroscopy(SERS).To validate the scheme,we also performed a simulation for the system and found qualitative agreement with the experimental results.The method that combines DEP,pipette-based AFM,and SERS may widely expand the unique capabilities of 3D printing and nano-micro patterning for multi-material patterning,materials sorting,and diverse advanced applications.

Atomic force microscope study of WC-10Co cemented carbide sintered from nanocrystalline composite powders

In order to compare the spark plasma sintedng （SPS） process plus hot isostatic press （HIP） with vacuum sintedng plus HIP, an investigation was carried out on the topography, microstructure and gain size distribution of nanocrystalline WC-10Co composite powder and the sintered specimens prepared by SPS plus HIP and by vacuum sintering plus HIP by means of atomic force microscopy （AFM）. The mechanical properties of the sintered specimens were also investigated. It is very easy to find cobalt lakes in the specimen prepared by vacuum sintering plus HIP process. But the microstructure of the specimen prepared by SPS plus HIP is more homogeneous, and the grain size is smaller than that prepared by vacuum sintering plus HIP. The WC-10Co ultrafine cemented carbide consolidated by SPS plus HIP can reach a relative density of 99.4%, and the transverse rupture strength （TRS） is higher than 3540 MPa, the Rockwell A hardness （HRA） is higher than 92.8, the average grain size is smaller than 300 nm, and the WC-10Co ultrafine cemented carbide with excellent properties is achieved. The specimen prepared by SPS with HIP has better properties and microstructure than that prepared by vacuum sintering with HIP.

Observation and characterization of asphalt microstructure by atomic force microscopy

The microstructure of asphalt is investigated by atomic force microscopy （AFM）. In order to analyze the impacts of asphalt types on microstructures, two neat asphalts with different penetration grades （50# and 70#） and one styrene-butadiene-styrene （SBS） modified asphalt are chosen. The influence of short-term aging is also studied. Based on the knowledge of asphalt＇s microproperties, the relationship between microstructures and healing property is analyzed. The results indicate that the microstructures of three asphalts are quite different and the effects of aging on the surface characteristics for different asphalts are also different. It is proposed that the bee structure is a type of wax crystal and it has a close relationship with the ＂bridge-healing＂ mechanism. The findings may reveal the formation mechanism of microstructure and the healing property for asphalts.

Research on a Diamond Tip Wear Mechanism in Atomic Force Microscope-based Micro/nano-machining

The object is to investigate the wear of an atomic force microscope (AFM) diamond tip when conducting micro/nano machining on single crystal silicon surface. The experimental research and theoretical analysis were carried out on the worn tip in terms of wear rate, wear mechanism and the effect of the tip wear on micro machining process. The wear rate was calculated as 1.7(10～10mm 3/(N·m) by using a theoretical model combined with the experimental results. Through an integration of an AFM observation on the worn tip features with the FEM simulation of the stress distribution, in addition to the unit cutting force calculation on the AFM diamond tip, the wear mechanism of the AFM diamond tip was concluded as mainly chemical wear, and the wear process was also elaborated as well.

Surface topography of La-Ti composite oxide nanocrystallines examined with atomic force microscope

By means of atomic force microscope, the surface pattern, particle size distribution, and specific surface area of La Ti composite oxide were studied. The compound particle surface appears as a smooth sheet, the even size of the compound ranges from 19.85 nm to 25.38 nm. The particle seems smooth, which erects at a height from 4.69 nm to 5.88 nm.The surface area ranges from 58.90 nm 2 to 1 238.04 nm 2. The La Ti composite oxide nanocrystallines enjoy a narrow and even particle size distribution and accumulate closely.

Edge Effects and Coupling Effects in Atomic Force Microscope Images

The AFM images were obtained by an atomic force microscope (AFM) and transformed from the deformation of AFM micro cantilever probe. However, due to the surface topography and surface forces applied on the AFM tip of sample, the deformation of AFM probe results in obvious edge effects and coupling effects in the AFM images.The deformation of AFM probe was analyzed,the mechanism of the edge effects and the coupling effects was investigated, and their results in the AFM images were studied. It is demonstrated by the theoretical analysis and AFM experiments that the edge effects make lateral force images more clear than the topography images,also make extraction of frictional force from lateral force images more complex and difficult. While the coupling effects make the comparison between topography images and lateral force images more advantage to acquire precise topography information by AFM.

Preparation of La-Ti Composite Oxide Nanocrystal and Examination of Their Surface Topography with Atomic Force Microscope

With sol-gel method, nanometer La-Ti composite oxide was successfully prepared at a low temperature (750～800C) using polyethylene glycol as dispersant. By means of atomic force microscope, the surface pattern, particle size distribution, and specific surface area were studied. The compound particle surface appears as a smooth sheet, the mean size of the compound is 25.38 nm. On the specific surface, the particle erects at a height of 4.69 nm. The surface area is 58.90 nm2. The La-Ti composite oxide nanocrystal prefers to narrow and even particle size distribution and the homogeneity of surface topography.

Competitive Adsorption between Bovine Serum Albumin and Collagen Observed by Atomic Force Microscope

Atomic force microscopy (AFM) was used to study the competitive adsorption betweenbovine serum albumin (BSA) and type Ⅰ collagen on hydrophilic and hydrophobic silicon wafers.BSA showed a grain shape and the type Ⅰ collagen displayed fibril-like molecules with relativelyhomogeneous height and width, characterized with clear twisting (helical formation). These AFMimages illustrated that quite a lot of type Ⅰ collagen appeared in the adsorption layer on hydrophilicsurface in a competitive adsorption state, but the adsorption of BSA was more preponderant than thatof type Ⅰ collagen on hydrophobic silicon wafer surface. The experiments showed that theinfluence of BSA on type Ⅰ collagen adsorption on hydrophilic surface was less than that onhydrophobic surface.

Studying Aggregate in Lysozyme Solution by Atomic Force Microscope

The aggregates in lysozyme solution with different NaCl concentration were investigated by Atomic Force Microscope (AFM). The AFM images show that there exist lysozyme monomers, n-mers and clusters in lysozyme solution when the conditions are not suitable for crystal growth. In favorable conditions for crystal growth, the lysozyme clusters disappear and almost only monomers exist in solution.

Development of XY scanner with minimized coupling motions for high-speed atomic force microscope

The design and fabrication processes of a novel scanner with minimized coupling motions for a high-speed atomic force microscope （AFM） were addressed. An appropriate design modification was proposed through the analyses of the dynamic characteristics of existing linear motion stages using a dynamic analysis program, Recurdyn. Because the scanning speed of each direction may differ, the linear motion stage for a high-speed scanner was designed to have different resonance frequencies for the modes, with one dominant displacement in the desired directions. This objective was achieved by using one-direction flexure mechanisms for each direction and mounting one stage for fast motion on the other stage for slow motion. This unsymmetrical configuration separated the frequencies of two vibration modes with one dominant displacement in each desired direction, and hence suppressed the coupling between motions in two directions. A pair of actuators was used for each axis to decrease the crosstalk between the two motions and give a sufficient force to actuate the slow motion stage, which carried the fast motion stage, A lossy material, such as grease, was inserted into the flexure hinge to suppress vibration problems that occurred when using an input triangular waveforrn. With these design modifications and the vibration suppression method, a novel scanner with a scanning speed greater than 20 Hz is achieved.

In situ observation of surface structures of cardiovascular endothelial cells with atomic force microscope

Objective To observe the surface structures of cardiovascular endothelial cells in situ with atomic force microscope （AFM）. Methods Fresh aorta and aortic valve were dissected from 10 healthy male New Zealand white rabbits. Before fixed in 1% formaldehyde, the fresh tissues were washed in the buffer phosphate solution. Under general microscope, the fixed aorta or valve was spread on the double side stick tape which had already been stuck on the glass slide. The intima of aorta or the aorta side of valve was towards upside, Then the specimen was dried under 37 degrees centigrade in an attemperator and was washed with pure water. After dried again, the specimen was loaded on the platform ofNanoScope Ⅲa AFM and was scanned in tapping mode with the scanning speed of 0.5 HZ. Results The surface structures of endothelial cell on the fixed and dried tissue could be observed clearly in situ with AFM. aortic endothelial cells were large, branched and arranged sparsely and parallel to the direction of blood flow, whereas endothelial cells on aorta valve surface were small, less branched and arranged intensively and vertical to the direction of blood flow. When the scanning range was dwindled, granular ultra-structures could be observed on the surface of endothelial cells, and, as the scanning range was dwindled further, fissure and convolution could be seen on the surface of granules from aortic endothelial cells. Centre cavity and surrounding swelling volcano-like structure could be seen on the surface of granules from endothelial cells of aortic valve. Conclusions It＇s feasible to observe the surface ultra-structures of cardiovascular endothelial cells in situ with AFM and morphological information provided by AFM might be of clinical value in future histopathological diagnosis（JGeriatr Cardiol2009; 6：178-181）.

Constant Force Feedback Controller Design Using PID-Like Fuzzy Technique for Tapping Mode Atomic Force Microscopes

A novel constant force feedback mechanism based on fuzzy logic for tapping mode Atomic Force Microscopes (AFM) is proposed in this paper. A mathematical model for characterizing the cantilever-sample interaction subsystem which is nonlinear and contains large uncertainty is first developed. Then, a PID-like fuzzy controller, combing a PD-like fuzzy controller and a PI controller, is designed to regulate the controller efforts and schedule the applied voltage of the Z-axis of the piezoelectric tube scanner to maintain a constant tip-sample interaction force during sample-scanning. Using the PID-like fuzzy controller allows the cantilever tip to track sample surface rapidly and accurately even though the topography of the surface is arbitrary and not given in advance. This rapid tracking response facilitates us to observe samples with high aspect ratio micro structures accurately and quickly. Besides, the overshoot which will result in tip crash in commercial AFMs with a traditional PID controller could be avoided. Additionally, the controller efforts can be intelligently scheduled by using the fuzzy logic. Thus, continuous manual gain-tuning by trial and error such as those in commercial AFMs is alleviated. In final, computer simulations and experimental verifications are provided to demonstrate the effectiveness and confirm the validity of the proposed controller.

Antiproliferative effects of cinobufacini on human hepatocellular carcinoma HepG2 cells detected by atomic force microscopy

AIM:To investigate the antiproliferative activity of cinobufacini on human hepatocellular carcinoma HepG2 cells and the possible mechanism of its action.METHODS:HepG2 cells were treated with different concentrations of cinobufacini.Cell viability was measured by methylthiazolyl tetrazolium(MTT) assay.Cell cycledistribution was analyzed by flow cytometry(FCM).Cytoskeletal and nuclear alterations were observed by fluorescein isothiocyanate-phalloidin and DAPI staining under a laser scanning confocal microscope.Changes in morphology and ultrastructure of cells were detected by atomic force microscopy(AFM) at the nanoscale level.RESULTS:MTT assay indicated that cinobufacini significantly inhibited the viability of HepG2 cells in a dosedependent manner.With the concentration of cinobufacini increasing from 0 to 0.10 mg/m L,the cell viability decreased from 74.9% ± 2.7% to 49.41% ± 2.2% and 39.24% ± 2.1%(P < 0.05).FCM analysis demonstrated cell cycle arrest at S phase induced by cinobufacini.The immunofluorescence studies of cytoskeletal and nuclear morphology showed that after cinobufacini treatment,the regular reorganization of actin filaments in HepG2 cells become chaotic,while the nuclei were not damaged seriously.Additionally,high-resolution AFM imaging revealed that cell morphology and ultrastructure changed a lot after treatment with cinobufacini.It appeared as significant shrinkage and deep pores in the cell membrane,with larger particles and a rougher cell surface.CONCLUSION:Cinobufacini inhibits the viability of HepG2 cells via cytoskeletal destruction and cell membrane toxicity.

Application of Atomic Force Microscopy in the Study of Polysaccharide

This paper gives a brief introduction to basic principle and working mode of atomic force microscope （AFM）. Sample preparation methods and factors that affect the AFM imaging of polysaccharide are described in detail. Advance in using AFM for morphological observation and quantitative study on polysaccharide molecules are reviewed. Research on single molecule force spectroscopy of polysaccharide and determination and adjustment of conformational change of sugar residue are introduced. Perspective on further application of AFM in polysaccharide investigation is presented.

Hydration film measurement on mica and coal surfaces using atomic force microscopy and interfacial interactions

The hydration film on particle surface plays an important role in bubble-particle adhesion in mineral flotation process. The thicknesses of the hydration films on natural hydrophobic coal and hydrophilic mica surfaces were measured directly by atomic force microscopy （AFM） based on the bending mode of the nominal constant compliance regime in AFM force curve in the present study. Surface and solid-liquid interfacial energies were calculated to explain the forming mechanism of the hydration film and atomic force microscopy data. The results show that there are significant differences in the structure and thickness of hydration films on coal and mica surfaces. Hydration film formed on mica surface with the thickness of 22.5 nm. In contrast, the bend was not detected in the nominal constant compliance regime. The van der Waals and polar interactions between both mica and coal and water molecules are characterized by an attractive effect, while the polar attractive free energy between water and mica （-87.36 mN/m） is significantly larger than that between water and coal （-32.89 mN/m）, which leads to a thicker and firmer hydration layer on the mica surface. The interfacial interaction free energy of the coal/water/bubble is greater than that of mica. The polar attractive force is large enough to overcome the repulsive van der Waals force and the low energy barrier of film rupture, achieving coal particle bubble adhesion with a total interfacial free energy of-56.30 mN/m.