Application Strategies of Automatic Addressable Single-Lamp Control Technology in Tunnel Lighting

The article mainly studies the application strategy of automatic addressable single-lamp control technology in tunnel lighting.It encompasses an introduction to this technology,an analysis of the tunnel lighting system using automatic addressable single-lamp control technology,and outlines the main development direction for this technology in modern tunnel lighting.The aim is to offer insights that can inform the rational deployment of this technology,thereby enhancing the lighting control effectiveness in modern tunnels and meeting their specific lighting requirements more effectively.

A low-noise X-band microwave source with digital automatic frequency control for electron paramagnetic resonance spectroscopy

We report a new design of microwave source for X-band electron paramagnetic resonance spectrometer.The microwave source is equipped with a digital automatic frequency control circuit.The parameters of the digital automatic frequency control circuit can be flexibly configured for different experimental conditions,such as the input powers or the quality factors of the resonator.The configurability makes the microwave source universally compatible and greatly extends its application.To demonstrate the ability of adapting to various experimental conditions,the microwave source is tested by varying the input powers and the quality factors of the resonator.A satisfactory phase noise as low as-135 d Bc/Hz at 100-k Hz offset from the center frequency is achieved,due to the use of a phase-locked dielectric resonator oscillator and a direct digital synthesizer.Continuous-wave electron paramagnetic resonance experiments are conducted to examine the performance of the microwave source.The outstanding performance shows a prospect of wide applications of the microwave source in numerous fields of science.

Design and Simulation of an Audio Signal Alerting and Automatic Control System

A large part of our daily lives is spent with audio information. Massive obstacles are frequently presented by the colossal amounts of acoustic information and the incredibly quick processing times. This results in the need for applications and methodologies that are capable of automatically analyzing these contents. These technologies can be applied in automatic contentanalysis and emergency response systems. Breaks in manual communication usually occur in emergencies leading to accidents and equipment damage. The audio signal does a good job by sending a signal underground, which warrants action from an emergency management team at the surface. This paper, therefore, seeks to design and simulate an audio signal alerting and automatic control system using Unity Pro XL to substitute manual communication of emergencies and manual control of equipment. Sound data were trained using the neural network technique of machine learning. The metrics used are Fast Fourier transform magnitude, zero crossing rate, root mean square, and percentage error. Sounds were detected with an error of approximately 17%;thus, the system can detect sounds with an accuracy of 83%. With more data training, the system can detect sounds with minimal or no error. The paper, therefore, has critical policy implications about communication, safety, and health for underground mine.

Principle, Modeling and Control of DC-DC Convertors for EV

DC DC convertors can convert the EV's high voltage DC power supply into the low voltage DC power supply. In order to design an excellent convertor one must be guided by theory of automatic control. The principle and the method of design, modeling and control for DC DC convertors of EV are introduced. The method of the system response to a unit step function input and the frequency response method are applied to researching the convertor's mathematics model and control characteristic. Experiments show that the designed DC DC convertor's output voltage precision is high, the antijamming ability is strong and the adjustable performance is fast and smooth.

Design and implementation of digital closed-loop drive control system of a MEMS gyroscope

In order to effectively control the working state of the gyroscope in drive mode, the drive characteristics of the micro electromechanical system （MEMS） gyroscope are analyzed in principle. A novel drive circuit for the MEMS gyroscope in digital closed-loop control is proposed, which utilizes a digital phase-locked loop （PLL） in frequency control and an automatic gain control （AGC） method in amplitude control. A digital processing circuit with a field programmable gate array （FPGA） is designed and the experiments are carried out. The results indicate that when the temperature changes, the drive frequency can automatically track the resonant frequency of gyroscope in drive mode and that of the oscillating amplitude holds at a set value. And at room temperature, the relative deviation of the drive frequency is 0.624 ×10^-6 and the oscillating amplitude is 8.0 ×10^-6, which are 0. 094% and 18. 39% of the analog control program, respectively. Therefore, the control solution of the digital PLL in frequency and the AGC in amplitude is feasible.

Single-Stage Wide-Range CMOS VGA with Temperature Compensation and Linear-in-dB Gain Control

A novel wide-range CMOS variable gain amplifier （VGA） topology is presented. The proposed VGA is composed of a variable transconductor and a novel variable output resistor and can offer a high gain variation range of 80dB while using a single variable-gain stage. Temperature-compensation and decibel-linear gain characteristic are achieved by using a control circuit that provides a gain error lower than ±1.5dB over the full temperature and gain ranges. Realized in 0.25μm CMOS technology, a prototype of the proposed VGA provides a total gain range of 64.5dB with 55.6dB-linear range,a P-1dB varying from - 17.5 to 11.5dBm,and a 3dB-bandwith varying from 65 to 860MHz while dissipating 16.5mW from a 2.5V supply voltage.

Automatic Control of Automobile Transmission Performance Test Stand

To realize automatic control of automobile transmission performance test stand Methods The automatic control technique of the lubricant temperature,the program- controll- edautomaticshifting of the transmission,the continuous adjusting of revolution speed and load, data-acquisition and data real-time processing were adopted.Results The lubricant temperature was controlled at the set temperature ±2℃.The automatic shifting of the trans- mission is simple,reliable and accurate.The automatic adjusting of load and rotation speed is rapidandaccurate,the torque divergence is ±1N·m,the rotation speed divergence is ±5r/min Conclusion The four kinds of techniques are applied into the automobile transmission perfor- mance test stand successfully. mancetest stand successfully.

Improved Smith prediction monitoring AGC system based on feedback-assisted iterative learning control

The performance of Smith prediction monitoring automatic gauge control(AGC) system is influenced by model mismatching greatly in strip rolling process. Aiming at this problem, a feedback-assisted iterative learning control strategy, which learned unknown modeling error by using previous control information repeatedly, was introduced into Smith prediction monitoring AGC system. Firstly, conventional Smith predictor and improved Smith predictor with PI-P controller were analyzed. Secondly, on the basis of establishing of feedback-assisted iterative learning control strategy for improved Smith predictor, process control signal update law and control error were deduced, then convergence condition of this strategy was put forward and proved. Finally, after modeling the automatic position control system, the PI-P Smith prediction monitoring AGC system with feedback-assisted iterative learning control was researched through simulation. Simulation results indicate that this system remains stable during model mismatching. The robustness and response of monitoring AGC is improved by development of feedback-assisted iterative learning control strategy for PI-P Smith predictor.

HUMAN-IMITATING INTELLIGENT CONTROL AND TRIPLE INVERTED-PENDULUM

A 'Human-Imitating Intelligent Control Theory' with 'generalized reduction' and 'Human Imitating' concepts as its kernel is proposed. And a world puzzlein the control circles is solved successfully based on this theory. The puzzle is thewell-known 'triple inverted pendulum control' using a SINGLE motor. A human-imitating intelligent technique to control inverted pendulum is here described. The success. ful experimental results show that our control objective can be achieved without a precise mathematical model of the plant. Finally, general principles of designing complexautomatic control systems based on the human-imitating intelligent control theory areconcluded.

Monitor automatic gauge control strategy with a Smith predictor for steel strip rolling

The simplified transfer function diagram block for a monitor automatic gauge control （Mon-AGC） system of strip steel rolling process was investigated. The new notion of strip sample length was given. In this way, the delay time varying with the rolling speed was evaded. After a Smith predictor was used to monitor the AGC system, the control laws were deduced for both proportional and integral regulators. The control strategies showed that by choosing the controller parameter P=∞ for both control algo- rithms each regulator could compensate the whole strip gage error in the first control step. The result shows that the integral algo- rithm is more controllable for the system regulating process and has a better steady-state precision than the proportional regulator. Compared with the traditional control strategy, the new control laws have a faster response speed and a hieher steadv-state precision.

An Expert System in Automatic Gauge Control for Rolling Process

Beacuse the practical mathematic model of rolling process can't be built accurately,this paper established an expert system to control the rolling steels' gauge by adjusting the setup roll open, which combined the experience of theoreticians and operators. The system applied the expression method of rule-skeleton+rule-body', and selected an appropriate non-exact reference model and self-study algorithm. The whole system, including auxiliary routes, is designed in Borland C++. Some experiments on this system have been done, and a good result has been achieved.

Mathematical model of electric hydraulic and powered support control system at a plough mining face

Given the actual working of a fully mechanized plough at a mining face, we have proposed a formula for running constraints between powered supports and a coal plough under assumed geological conditions of the coal face and, on this basis, established an automatic control model of powered supports for the coal plough face. We introduced the working principle of the powered support control system of the plough at the mining face. We established three advanced characteristics of this control system： response speed, reliability and easy maintenance of the system. As well, we briefly introduced, the principal function of primary and subordinate controllers and the realization of the communication system by a Single Bus. Ten controllers were constructed and tested in our laboratorium. The results show that the control model is practical and meets actual conditions. It provides a theoretical basis for designing a comouter control system for a oowered support system of a plough at a mining face.

Multi-timescale robust dispatching for coordinated automatic generation control and energy storage

The increasing penetration of renewable energy into power grids is reducing the regulation capacity of automatic generation control(AGC).Thus,there is an urgent demand to coordinate AGC units with active equipment such as energy storage.Current dispatch decision-making methods often ignore the intermittent effects of renewable energy.This paper proposes a two-stage robust optimization model in which energy storage is used to compensate for the intermittency of renewable energy for the dispatch of AGC units.This model exploits the rapid adjustment capability of energy storage to compensate for the slow response speed of AGC units,improve the adjustment potential,and respond to the problems of intermittent power generation from renewable energy.A column and constraint generation algorithm is used to solve the model.In an example analysis,the proposed model was more robust than a model that did not consider energy storage at eliminating the effects of intermittency while offering clear improvements in economy and efficiency.

DECENTRALIZED OUTPUT FEEDBACK FAULT一TOLERANT CONTROL FOR UNCERTAIN LARGE一SCALE SYSTEMS

ＤＥＣＥＮＴＲＡＬＩＺＥＤＯＵＴＰＵＴＦＥＥＤＢＡＣＫＦＡＵＬＴ一ＴＯＬＥＲＡＮＴＣＯＮＴＲＯＬＦＯＲＵＮＣＥＲＴＡＩＮＬＡＲＧＥ一ＳＣＡＬＥＳＹＳＴＥＭＳＨｕＳｈｏｕｓｏｎｇ；ＦａｎＣｕｎｈａｉ（ＤｅｐａｒｔｍｅｎｔｏｆＡｕｔｏｍａｔｉｃＣｏｎｕｏ...

Treatment of Phenol-Contaminated Soil by Potassium Ferrate Based on pH Control

This study aims to optimize the treatment of phenol-contaminated soil by potassium ferrate. Variations in pH value can accurately reflect the state and reaction status of the entire treatment process. Therefore, the pH value could be an important variable for optimizing the reaction conditions and achieving the automatic control of the process. About 99.89% of phenol was removed after 10 min of the pH-contxolled reaction at a rotational speed of 40-70 r/min, with the initial phenol concentration equating to 10.0 g/kg and the total water consumption reaching 2.72 L （at a soil/water ratio of 1：0.68）. The test results could provide a basis for practical application of automatic reaction control by pH value.

Study and application of crown feedback control in hot strip rolling

Crown feedback control is one part of the automatic shape control （ASC） system. On the basis of large simulation researches conducted, a linear crown feedback control model was put forward and applied in actual strip rolling. According to its successful op- eration in the ASP 1700 hot strip mill of Angang Group for one year and also from the statistical results of several crown measurements, it can be definitely said that this control model is highly effective and shows stable performance. The control effectiveness of different gauges of strips with the feedback control is found to increase by 10%-30% compared with that without feedback control.

Control structure comparison for three-product Petlyuk column

The focus of this paper is to investigate different control structures(single-loop PI control) for a dividing wall(Petlyuk) column for separating ethanol, n-propanol and n-butanol. Four control structures are studied. All the results are simulations based on Aspen Plus. Control structure 1(CS1) is stabilizing control structure with only temperature controllers. CS2, CS3 and CS4, containing also composition controllers, are introduced to reduce the steady state composition deviations. CS2 adds a distillate composition controller(CCDB) on top of CS1. CS3 is much more complicated with three temperature-composition cascade controllers and in addition a selector to the reboiler duty to control the maximum controller output of light impurity composition control in side stream and bottom impurity control in the prefractionator. CS4 adds another high selector to control the light impurity in the sidestream. Surprisingly, when considering the dynamic and even steady state performance of the proposed control structures, CS1 proves to be the best control structure to handle feed disturbances inserted into the three-product Petlyuk column.

Design of a modern automatic control system for the activated sludge process in wastewater treatment

The Activated Sludge Process(ASP) exhibits highly nonlinear properties. The design of an automatic control system that is robust against disturbance of inlet wastewater flow rate and has short process settling times is a challenging matter. The proposed control method is an I-P modi fied controller automatic control system with state variable feedback and control canonical form simulation diagram for the process. A more stable response is achieved with this type of modern control. Settling times of 0.48 days are achieved for the concentration of microorganisms,(reference value step increase of 50 mg·L-1) and 0.01 days for the concentration of oxygen(reference value step increase of 0.1 mg·L-1). Fluctuations of concentrations of oxygen and microorganisms after an inlet disturbance of5 × 103m3·d-1are small. Changes in the reference values of oxygen and microorganisms(increases by 10%, 20% and 30%) show satisfactory response of the system in all cases. Changes in the value of inlet wastewater flow rate disturbance(increases by 10%, 25%, 50% and 100%) are stabilized by the control system in short time. Maximum percent overshoot is also taken in consideration in all cases and the largest value is 25% which is acceptable. The proposed method with I-P controller is better for disturbance rejection and process settling times compared to the same method using PI controller. This method can substitute optimal control systems in ASP.

Improved Voltage Control Strategy for Photovoltaic Grid-Connected System Based on DoubleLayer Coordination Control

An improved automatic voltage coordination control strategy （AVCCS） based on ;automatic voltage control （AVC） and battery energy storage control （BESC） is proposed for photovoltaic grid-connected system （PVGS） to mitigate the voltage fluctuations caused by environmental disturbances. Only AVC is used when small environ- mental disturbances happen, while BESC is incorporated with AVC to restrain the voltage fluctuations when large disturbances happen. An adjustable parameter determining the allowed amplitudes of voltage fluctuations is introduced to realize the above switching process. A benchmark low voltage distribution system including ]？VGS is established by using the commercial software Dig SILENT. Simulation results show that the voltage under AVCCS satisfies the IEEE Standard 1547, and the installed battery capacity is also reduced. Meanwhile, the battery＇s service life is ex- tended by avoiding frequent charges/discharges in the control process.

Effectiveness of Automatic Control over Flash Distillation Kettle for Liquid-Phase Bulk Polymerization of Propylene

Automatic control over flash distillation section at SINOPEC Cangzhou Refinery has been realized, resulting in saving of propylene feedstock and emission reduction to harvest significant economic benefits.