Experimental studies are carried out at a low speed axial compressor with five different rotor/stator gaps. Analysis of the effect of axial spacing of two successive blade rows on the measured mean flow coefficient at...Experimental studies are carried out at a low speed axial compressor with five different rotor/stator gaps. Analysis of the effect of axial spacing of two successive blade rows on the measured mean flow coefficient at stall inception and on the flow range of compressor under multi-cell rotating stall operating conditions proves that the stator can suppress the flow disturbance in the compressor and strengthen the stability of the compressor. Experimental data show that the stall flow coefficient decreases by reducing the axial spacing of successive blade rows. Moreover, by reducing the axial spacing, the stall pattern transition pace from multi-cell stall to single-cell stall can be shifted. And the compressor directly slips into single-cell stall at 21.0% CR axial spacing. By analyzing the pressure fluctuation closed to the surge line, it can be known that there exists an eigenfrequency where the amplitude of the oscillating pressure suddenly and dramatically increases as the compressor runs close to the surge line and this pressure disturbance is relevant to the compressor instability.展开更多
The hydrodynamic performance of a hybrid CRP pod propulsion system was studied by RANS method with SST k ?? turbulence model and sliding mesh. The effect of axial spacing on the hydrodynamic performance of the hybri...The hydrodynamic performance of a hybrid CRP pod propulsion system was studied by RANS method with SST k ?? turbulence model and sliding mesh. The effect of axial spacing on the hydrodynamic performance of the hybrid CRP pod propulsion system was investigated numerically and experimentally. It shows that RANS with the sliding mesh method and SST k -ω turbulence model predicts accurately the hydrodynamic performance of the hybrid CRP pod propulsion system. The axial spacing has little influence on the hydrodynamic performance of the forward propeller, but great influence on that of the pod unit. Thrust coefficient of the pod unit declines with the increase of the axial spacing, but the trend becomes weaker, and the decreasing amplitude at the lower advance coefficient is larger than that at the higher advance coefficient. The thrust coefficient and open water efficiency of the hybrid CRP pod propulsion system decrease with the increase of the axial spacing, while the torque coefficient keeps almost constant. On this basis, the design principle of axial spacing of the hybrid CRP pod propulsion system was proposed.展开更多
Using the variable transformation method,the formulae of the axial symmetrical wall temperature distribution during steady heat conduction of a hollow cylinder are derived in this paper.The wall temperature distributi...Using the variable transformation method,the formulae of the axial symmetrical wall temperature distribution during steady heat conduction of a hollow cylinder are derived in this paper.The wall temperature distribution and the wall heat flux distribution in both axial and radial direction can be calculated by the temperature distribution of the liquid medium both inside and outside the cylinder with temperature changing in axial direction.The calculation results are almost consistent with the experience results.The applicative condition of the formulae in this paper consists with most of practice.They can be applied to the engineering calculation of the steady heat conduction.The calculation is simple and accurate.展开更多
文摘Experimental studies are carried out at a low speed axial compressor with five different rotor/stator gaps. Analysis of the effect of axial spacing of two successive blade rows on the measured mean flow coefficient at stall inception and on the flow range of compressor under multi-cell rotating stall operating conditions proves that the stator can suppress the flow disturbance in the compressor and strengthen the stability of the compressor. Experimental data show that the stall flow coefficient decreases by reducing the axial spacing of successive blade rows. Moreover, by reducing the axial spacing, the stall pattern transition pace from multi-cell stall to single-cell stall can be shifted. And the compressor directly slips into single-cell stall at 21.0% CR axial spacing. By analyzing the pressure fluctuation closed to the surge line, it can be known that there exists an eigenfrequency where the amplitude of the oscillating pressure suddenly and dramatically increases as the compressor runs close to the surge line and this pressure disturbance is relevant to the compressor instability.
基金financially supported by the National Natural Science Foundation of China(Grant Nos.51479207 and 51179198)the High Technology Marine Scientific Research Project of the Ministry of Industry and Information Technology of China(Grant No.[2012]534)
文摘The hydrodynamic performance of a hybrid CRP pod propulsion system was studied by RANS method with SST k ?? turbulence model and sliding mesh. The effect of axial spacing on the hydrodynamic performance of the hybrid CRP pod propulsion system was investigated numerically and experimentally. It shows that RANS with the sliding mesh method and SST k -ω turbulence model predicts accurately the hydrodynamic performance of the hybrid CRP pod propulsion system. The axial spacing has little influence on the hydrodynamic performance of the forward propeller, but great influence on that of the pod unit. Thrust coefficient of the pod unit declines with the increase of the axial spacing, but the trend becomes weaker, and the decreasing amplitude at the lower advance coefficient is larger than that at the higher advance coefficient. The thrust coefficient and open water efficiency of the hybrid CRP pod propulsion system decrease with the increase of the axial spacing, while the torque coefficient keeps almost constant. On this basis, the design principle of axial spacing of the hybrid CRP pod propulsion system was proposed.
文摘Using the variable transformation method,the formulae of the axial symmetrical wall temperature distribution during steady heat conduction of a hollow cylinder are derived in this paper.The wall temperature distribution and the wall heat flux distribution in both axial and radial direction can be calculated by the temperature distribution of the liquid medium both inside and outside the cylinder with temperature changing in axial direction.The calculation results are almost consistent with the experience results.The applicative condition of the formulae in this paper consists with most of practice.They can be applied to the engineering calculation of the steady heat conduction.The calculation is simple and accurate.