Experimental investigation of axially loaded steel fiber reinforced high strength concrete-filled steel tube columns

An experimental study on the compressive behavior of steel fiber reinforced concrete-filled steel tube columns is presented. Specimens were tested to investigate the effects of the concrete strength, the thickness of steel tube and the steel fiber volume fraction on the ultimate strength and the ductility. The experimental results indicate that the addition of steel fibers in concrete can significantly improve the ductility and the energy dissipation capacity of the concrete-filled steel tube columns and delay the local buckling of the steel tube, but has no obvious effect on the failure mode. It has also been found that the addition of steel fibers is a more effective method than using thicker steel tube in enhancing the ductility, and more advantageous in the case of higher strength concrete. An analytical model to estimate the load capacity is proposed for steel tube columns filled with both plain concrete and steel fiber reinforced concrete. The predicted results are in good agreement with the experimental ones obtained in this work and literatures.

Investigation of granite failure precursor under axial load using modified LSTM framework

Granite is usually composed of quartz,biotite,feldspar,and cracks,and the variation characteristics of these components could reflect the deformation and failure process of rock well.Taking granite as an example,the video camera was used to record the deformation and failure process of rock.The distribution of meso-components in video images was then identified.The meso-components of rock failure precursors were also discussed.Moreover,a modified LSTM(long short-term memory method)based on SSA(sparrow search algorithm)was proposed to estimate the change of meso-components of rock failure precursor.It shows that the initiation and expansion of cracks are mainly caused by feldspar and quartz fracture,and when the quartz and feldspar exit the stress framework,rock failure occurs;the second large increase of crack area and the second large decrease of quartz or feldspar area may be used as a precursor of rock failure;the precursor time of rock failure based on meso-scopic components is about 4 s earlier than that observed by the naked eye;the modified LSTM network has the strongest estimation ability for quartz area change,followed by feldspar and biotite,and has the worst estimation ability for cracks;when using the modified LSTM network to predict the precursors of rock instability and failure,quartz and feldspar could be given priority.The results presented herein may provide reference in the investigation of rock failure mechanism.

Axial load-share ratio testing to assess the healing of open tibial fractures treated with the Taylor Spatial Frame

Background:The Taylor Spatial Frame(TSF)has gained popularity among orthopedic surgeons for treating open fractures.However,a key challenge is the timely and safe removal of the frame.This study assessed the efficacy and safety of axial load-share ratio(ALSR)testing to evaluate callus healing strength after TSF treatment of open tibial fractures.Methods:A retrospective case-control study was conducted,analyzing 180 adult patients with open tibial fractures treated at Tianjin Hospital’s Orthopedic Limb Correction Unit between August 2019 and August 2022.All patients underwent TSF external fixation surgery,and were divided into two groups based on ALSR testing.Group I(92 patients)underwent ALSR testing,with frame removal if the test value fell below 5%.Traditional methods were used for fixator removal guidance in Group II(88 patients).Clinical outcomes,including fixation duration,complications after fixator removal,and Johner-Wruhs functional scores,were compared between the two groups.Results:The groups showed no statistically significant differences(P>0.05)in sex,age,injury side,body mass index,surgery timing,or fracture type.Group I had a significantly shorter fixation duration(25.85±5.57 weeks)compared to Group II(31.82±6.98 weeks)(P<0.05).Following fixator removal,Group I demonstrated superior Johner-Wruhs scores compared to Group II,indicating better outcomes(P<0.05).Complication rates did not differ significantly between the groups at the last follow-up(P>0.05).Conclusion:Regular postoperative ALSR testing could safely and effectively guide TSF removal following open tibial fracture treatment.This method significantly reduced fixation duration compared to traditional guidance methods while maintaining efficacy and safety.

DYNAMIC BUCKLING OF STATICALLY PRELOADED RING-STIFFENED CYLINDRICAL SHELLS UNDER AXIAL FLUID-SOLID IMPACT LOADING

The Initial Imperfection Amplified Criterion is applied toinvestigate the geometric nonlinear dynamic buckling of staticallypreloaded ring-stiffened cylindrical shells under axial fluid-solidimpact. Tak- ing account of the effects of large deformation andinitial geometric imperfection, the governing equations are obtainedby the Galerkin method and solved by the Runge-Kutta method. Theeffects of static preloading (uniform external radial pressure) onthe buckling features and the load-carrying ability of ring-stiffenedcy- lindrical shells against axial impact are discussed.

POST-BUCKLING ANALYSIS AND STRUCTURE OPTIMIZATION OF INTEGRAL FUSELAGE PANEL SUBJECTED TO AXIAL COMPRESSION LOAD

Build-up panels for the commercial aircraft fuselage subjected to the axial compression load are studied by both experimental and theoretical methods.An integral panel is designed with the same overall size and weight as the build-up structure,and finite element models（FEMs）of these two panels are established.Experimental results of build-up panels agree well with the FEM results with the nonliearity and the large deformation,so FEMs are validated.FEM calculation results of these two panels indicate that the failure mode of the integral panel is different from that of the build-up panel,and the failure load increases by 18.4% up to post-buckling.Furthermore,the integral structure is optimized by using the multi-island genetic algorithm and the sequential quadratic programming.Compared with the initial design,the optimal mass is reduced by 8.7% and the strength is unchanged.

Seismic performance of steel reinforced ultra high-strength concrete composite frame joints

To investigate the seismic performance of a composite frame comprised of steel reinforced ultra high-strength concrete （SRUHSC） columns and steel reinforced concrete （SRC） beams, six interior frame joint specimens were designed and tested under low cyclically lateral load. The effects of the axial load ratio and volumetric stirrup ratio were studied on the characteristics of the frame joint performance including crack pattern, failure mode, ductility, energy dissipation capacity, strength degradation and rigidity degradation. It was found that all joint specimens behaved in a ductile manner with flexural-shear failure in the joint core region while plastic hinges appeared at the beam ends. The ductility and energy absorption capacity of joints increased as the axial load ratio decreased and the volumetric stirIup ratio increased. The displacement ductility coefficient and equivalent damping coefficient of the joints fell between the corresponding coefficients of the steel reinforced concrete （SRC） frame joint and RC frame joint. The axial load ratio and volumetric stirrup ratio have less influence on the strength degradation and more influence on the stiffness degradation. The stiffness of the joint degrades more significantly for a low volumetric stirrup ratio and high axial load ratio. The characteristics obtained from the SRUHSC composite frame joint specimens with better seismic performance may be a useful reference in future engineering applications.

Experimental research on behavior of 460 MPa high strength steel I-section columns under cyclic loading

To investigate the seismic behavior of I-section columns made of 460 MPa high strength steel （HSS）, six specimens were tested under constant axial load and cyclic horizontal load. The specimens were designed with different width-to-thickness ratios and loaded under different axial load ratios. For each specimen, the failure mode was observed and hysteretic curve was measured. Comparison of different specimens on hysteretic characteristic, energy dissipation capacity and deformation capacity were further investigated. Test results showed that the degradation of bearing capacity was due to local buckling of flange and web. Under the same axial load ratio, as width-to-thickness ratio increased, the deformation area of local buckling became smaller. And also, displacement level at both peak load and failure load became smaller. In addition, the full extent of hysteretic curve, energy dissipation capacity, ultimate story drift angle decreased, and capacity degradation occurred more rapidly with the increase of width-to-thickness ratio or axial load ratio. Based on the capacity of story drift angle, limiting values which shall not be exceeded are suggested respectively for flange and web plate of 460 MPa HSS I-section columns when used in SMFs and in IMFs in the case of axial load ratio no more than 0.2. Such values should be smaller when the axial load ratio increases.

Axial bearing behavior of super-long piles in deep soft clay over stiff layers

In order to find out the bearing behavior of super-long piles located in deep soft clay over stiff layers around Dongting Lake, China, a test pile was first designed with the field loading test finished afterward. Based on the measured test results, load transfer mechanism and bearing behavior of the pile shaft were discussed in detail. Then, by introducing a bi-linear model for shaft friction and the tri-linear model for pile tip resistance, respectively, the governing differential equation of pile soil system was set up by the load transfer method with the analytical solutions derived as well, taking into account the effect by stratified feature and various bearing conditions of subsoil, material nonlinearity, and the sediment under pile tip. Furthermore, formulas to determine the axial capacity of super-long piles by the pile top settlement were advised and applied to analyze the test pile. Good agreement between the predicted load settlement variations and the measured data is obtained to verify the validity of the present method. The results also show that, the axial bearing capacity of super-long piles should be controlled by the allowable pile top settlement, and buckling stability of the pile shaft should be paid attention as well.

High-resolution,three-dimensional magnetic resonance imaging axial load dynamic study improves diagnostics of the lumbar spine in clinical practice

BACKGROUND The response to axial physiological pressure due to load transfer to the lumbar spine structures is among the various back pain mechanisms.Understanding the spine adaptation to cumulative compressive forces can influence the choice of personalized treatment strategies.AIM To analyze the impact of axial load on the spinal canal’s size,intervertebral foramina,ligamenta flava and lumbosacral alignment.METHODS We assessed 90 patients using three-dimensional isotropic magnetic resonance imaging acquisition in a supine position with or without applying an axial compression load.Anatomical structures were measured in the lumbosacral region from L1 to S1 in lying and axially-loaded magnetic resonance images.A paired t test atα=0.05 was used to calculate the observed differences.RESULTS After axial loading,the dural sac area decreased significantly,by 5.2%on average(4.1%,6.2%,P<0.001).The intervertebral foramina decreased by 3.4%(2.7%,4.1%,P<0.001),except for L5-S1.Ligamenta flava increased by 3.8%(2.5%,5.2%,P<0.001),and the lumbosacral angle increased.CONCLUSION Axial load exacerbates the narrowing of the spinal canal and intervertebral foramina from L1-L2 to L4-L5.Cumulative compressive forces thicken ligamenta flava and exaggerate lumbar lordosis.

Multi-objective optimization of multi-cell conical structures under dynamic loads

In this paper,crashworthiness performance of multi-cell conical tubes with new sectional configuration design(i.e.square,hexagonal,octagonal,decagon and circular)has been evaluated under axial and three different oblique loads.The same weight conical tubes were comparatively studied using an experimentally validated finite element model generated in LS-DYNA.Complex proportional assessment(COPRAS)method was then employed to select the most efficient tube using two conflicting criteria,namely peak collapse force(PCF)and energy absorption(EA).From the COPRAS calculations,the multi-cell conical tube with decagonal cross-section(MCDT)showed the best crashworthiness performance.Furthermore,the effects of possible number of inside ribs on the crashworthiness of the decagonal conical tubes were also evaluated,and the results displayed that the tubes performed better as the number of ribs increased.Finally,parameters(the cone angle,θ,and ratio of the internal tube size to the external one,S)of MCDT were optimized by adopting artificial neural networks(ANN)and genetic algorithm(GA)techniques.Based on the multi-objective optimization results,the optimum dimension parameters were found to beθ=7.9o,S=0.46 andθ=8o,S=0.74 from the minimum distance selection(MDS)and COPRAS methods,respectively.

Unified expression for failure of reinforced concrete members in bridge

Reinforced concrete structural elements with box section are commonly used in the horizontal and vertical structure of bridges. The reinforced concrete structure in bridge often failed under the combined forces of bending, axial load, shear and torsion caused by wind and earthquake. It is very important to study the mechanism of RC box section structures subjected to a combi-nation of forces. A theoretical study and deduction of the unified expression for failure of reinforced concrete members with box section under combined bending, shear, axial force and torsion were carried out with stress equilibrium assumption. Comparison of theoretical analysis results with experimental results showed that the unified expression for failure of reinforced concrete members with box section can be used for static calculation of such structure members.

Nosing process of empty and foam-filled circular metal tubes on semispherical die by theoretical and experimental investigations

Nosing process of circular metal tubes in empty and polyurethane foam-filled conditions on a semispherical rigid die was analyzed by theoretical and experimental methods.A new theoretical model of plastic deformation of circular metal tubes was demonstrated during the nosing process on a rigid semispherical die.Based on the analytical model,some theoretical relations were calculated to estimate instantaneous forming load and dissipated energy of empty and foam-filled circular metal tubes versus axial displacement.Some circular brazen and aluminum tubes were prepared and shaped into semispherical nosed nozzles to verify the present theory.Comparison of theoretical predictions and the corresponding experimental measurements reveals that predicted load?displacement and dissipated energy?displacement diagrams by theoretical formulas have a good correlation with the corresponding experimental curves and it proves verity of the theory.Also,the present theory shows that dissipated energy and axial load of empty tubes depend on material type,wall thickness and diameter of the tubes and they are independent of tube initial length.Furthermore,the experimental results show that the presence of polyethylene Teflon-constraints increases ultimate axial displacement of the forming process.

Numerical Analysis of Local Joint Flexibility of K-joints with External Plates Under Axial Loads in Offshore Tubular Structures

The Local Joint Flexibility(_(LJF))of steel K-joints reinforced with external plates under axial loads is investigated in this paper.For this aim,firstly,a finite element(FE)model was produced and verified with the results of several experimental tests.In the next step,a set of 150 FE models was generated to assess the effect of the brace angle(θ),the stiffener plate size(ηandλ),and the joint geometry(γ,τ,ξ,andβ)on the_(LJF)factor(f_(LJF)).The results showed that using the external plates can decrease 81%of the f_(LJF).Moreover,the reinforcing effect of the reinforcing plate on the f_(LJF)is more remarkable in the joints with smallerβ.Also,the effect of theγon the f_(LJF)ratio can be ignored.Despite the important effect of the f_(LJF)on the behavior of tubular joints,there is not available any study or equation on the f_(LJF)in any reinforced K-joints under axial load.Consequently,using the present FE results,a design parametric equation is proposed.The equation can reasonably predict the f_(LJF)in the reinforced K-joints under axial load.

Flexural Capacity Formula of Diaphragm-Through Joints of Concrete-Filled Square Steel Tubular Columns

Finite element analysis and parametric studies were performed to investigate the flexural capacity of the panel zone of diaphragm-through joints between concrete-filled square steel tubular columns and H-shaped steel beams. Through the comparisons of failure modes, load–displacement curves, and bearing capacity, it was found that the flexural capacity of the panel zone of diaphragm-through joints was determined by the tensile action and influence of the web of H-shaped steel beams, and the axial load should be taken into account. The steel tube and the diaphragm were the major parts of the joint that resisted the bending moment. The contribution of in-filled concrete had little influence on the flexural capacity of the panel zone of the joint and could be neglected. According to the results of these numerical studies, a formula that considered the influence of the web of H-shaped steel beams and the axial load was developed based on the yield lines in the diaphragm and the steel tube. The results of the proposed formula were in good agreement with the numerical data of this investigation. © 2017, Tianjin University and Springer-Verlag Berlin Heidelberg.

Analysis of Geometrical Parameters of Tubular TY-Joints on Stress Concentration Factors Due to Axial Loads

In this paper,the influence of geometric parameters on the stress concentration factors due to three different types of axial loading on 81 TY tubular structures is studied.Our results reveal that,geometric parameters have a considerable impact on the variation of stress concentration factors on tubular TY-joints under axial loads.Thus,the highest stress concentration factor values are observed on the vertical brace than on the inclined one.The finite element results of the tubular structures were verified by parametric equations and experimental data.A parametric study was carried out by analyses using the nonlinear regression method to obtain parametric equations.These equations are used to calculate stress concentration factors and to analyse the fatigue resistance of TY-joints due to axial loads.

Nonlinear fi nite element analysis of high-strength concrete columns and experimental verification

This paper describes a nonlinear finite element （FE） analysis of high strength concrete （HSC） columns, and verifies the results through laboratory experiments. First, a cyclically lateral loading test on nine cantilever column specimens of HSC is described and a numerical simulation is presented to verify the adopted FE models. Next, based on the FE model for specimen No.6, numerical simulations for 70 cases, in which different concrete strengths, stirrup ratios and axial load ratios are considered, are presented to explore the effect of these parameters on the behavior of the HSC columns, and to check the rationality of requirements for these columns specified in the China Code for Seismic Design of Buildings （GB 50011- 2001）. In addition, three cases with different stirrup strengths are analyzed to investigate their effect on the behavior of HSC columns. Finally, based on the numerical results some conclusions are presented.

Seismic ductility of very-high-strength-concrete short columns subject to combined axial loading and cyclic lateral loading

The seismic ductility of reinforced very-high-strength-concrete （VHSC） short columns was studied by combinatively applying axial load and low cyclic lateral load on specimens to simulate seismic impact. Twelve specimens with concrete compressive strength ranging from 95.6 MPa to 118.6 MPa and a shear-span ratio of 2.0 were tested for shear failure pattern and fear force-displacement hysteretic responses. Combinative application of axial load and low cyclic lateral load to VHSC short columns incurs shear failure. The displacement ductility is much smaller when the axial load ratio is larger; whereas a larger stirrup ratio is accompanied with a better displacement ductility. The relationship of displacement ductility factor,μ△, with stirrup characteristic value, λv, and test axial load ratio, nt, is μ△=（1＋8λv）/（0.33＋nt）. By this relationship and relevant codes for aseismatic design, the axial load ratio limits for aseismatic design of reinforced VHSC （C95 to C100） short columns for frame construction are respectively 0.5, 0.6, and 0.7 for seismic classes Ⅰ, Ⅱ, and Ⅲ; corresponding minimum characteristic values of stirrups are calculated according to the required characteristic values of at least 1.273 times of experimental results. These data are very useful to aseismatic engineering.

Behavior and design method of square-tubed reinforced concrete short columns under axial compression

The behavior of square-tubed reinforced concrete (STRC) short columns subjected to axial compression was studied in detail with an accurate nonlinear finite element model (FEM) . Different width to thickness ratios (D/t = 50 150) of the steel tube and the compressive strength of concrete (C80 and C50) were adopted in this research. The axial load strength,steel tube strain and load-shortening response were determined from FEM and the analysis results from FEM were compared with those from experiment. The analysis and test results indicate that the concrete strength little affectes the confinement of the steel tube on the concrete. The transverse stress of the tube at the axial load point increases with the increment in the width to thickness ratio. Based on the results from FEM and experiment,a formula for the prediction of the axial load strength was proposed in this paper.

Elastic solutions for partially embedded single piles subjected to simultaneous axial and lateral loading

In order to improve the design level of partially embedded single piles under simultaneous axial and lateral loads, the differential solutions were deduced, in which the soil was treated as an ideal, elastic, homogeneous, semi-infinite isotropic medium. A comparison was made between model test results and the obtained solutions to show their validity. The calculation results indicate that the horizontal displacement and bending moment of the pile increase with increases of the axial and lateral loads. The maximum horizontal displacement and bending moment decrease by 37.9% and 13.9%, respectively, when the elastic modulus of soil increases from 4 MPa to 20 MPa. The Poisson ratio of soil plays a marginal role in pile responses. There is a critical pile length under the ground, beyond which the pile behaves as though it was infinitely long. The presented solutions can make allowance for the continuous nature of soil, and if condition permits, they can approach exact ones.

Crashworthiness of double-cell conical tubes with different cross sections subjected to dynamic axial and oblique loads

Thin-walled tubes are increasingly used in automobile industries to improve structural safety.The present work deals with the collapse behavior of double-cell conical tubes subjected to dynamic axial and oblique loads.Crashworthiness of these tubes having different sections(e.g.,circular,square,hexagonal,octagonal,decagonal)was numerically investigated by using an experimentally validated finite element model generated in LS-DYNA.Geometry of these tubes was then optimized by decreasing the cross section dimensions at the distal end while the weight remained unchanged.Octagonal conical tube was finally found to be more preferable to the others as a collision energy absorber.In addition,square and circular tubes showed diamond deformation mode,while the other tubes collapsed in concertina mode.A decision making method called TOPSIS was finally implemented on the numerical results to select the most efficient energy absorber.