Gypsum-based Silica Gel Humidity-controlling Composite Materials:Preparation,Characterization,and Performance

Gypsum was used as substrate,and silica gel was mixed into substrate at a certain mass ratio to prepare humidity-controlling composites;moreover,the moisture absorption and desorption properties of gypsum-based composites were compared with adding different silica gel particle size and proportion.The morphological characteristics,the isothermal equilibrium moisture content curve,moisture absorption and desorption rate,moisture absorption and desorption stability,and humidity-conditioning performance were tested and analyzed.The experimental results show that,compared with pure-gypsum,the surface structure of the gypsum-based composites is relatively loose,the quantity,density and aperture of the pores in the structure increase.The absorption and desorption capacity increase along with the increase of silica gel particle size and silica gel proportion.When 3 mm silica gel particle size is added with a mass ratio of 40%,the maximum equilibrium moisture content of humidity-controlling composites is 0.161 g/g at 98% relative humidity(RH),3.22 times that of pure-gypsum.The moisture absorption and desorption rates are increased,the equilibrium moisture absorption and desorption rates are 2.68 times and 1.61 times that of pure-gypsum at 58.5% RH,respectively.The gypsum-based composites have a good stability,which has better timely response to dynamic humidity changes and can effectively regulate indoor humidity under natural conditions.

The Adsorption of Pb(II)Using Silica Gel Synthesized from Chemical Bottle Waste:Optimization Using Box-Behnken Design

The adsorption of Pb(II)on silica gel synthesized from chemical glass bottle waste has been studied.The effect of independent variables(adsorbent dose,initial concentration of Pb(II),contact time,and pH)on the Pb(II)removal from water was evaluated and optimized using the Response Surface Methodology(RSM).Under optimized conditions(adsorbent dose:20 mg;contact time:30 min;initial Pb(II)concentration:120 mg.L^(−1);and pH:8),the removal of Pb(II)was 99.77%.The adsorption equilibrium data obtained from the batch experiment were investigated using different isotherm models.The Langmuir isotherm model fits the experimental data.This shows that the surface of the silica gel synthesized from chemical bottles waste was covered by a Pb(II)monolayer.XRF analysis showed that the synthesized silica gel had a SiO_(2) content of 75.63%.Amorphous silica was observed from XRD analysis.SEM-EDX characterization showed that Pb was adsorbed on the silica gel surface.SEM analysis showed that silica gel has irregular particles with a surface area of 297.08 m2.g^(−1) with a pore radius of 15.74 nm calculated from BET analysis.

Silica Gel from Chemical Glass Bottle Waste as Adsorbent for Methylene Blue:Optimization Using BBD

This research focuses on the effective removal of methylene blue dye using silica gel synthesized from chemical glass bottle waste as an environmentally friendly and cost-effective adsorbent.The adsorption process was optimized using Box-Behnken Design(BBD)and Response Surface Methodology(RSM)to investigate the influence of pH(6;8 and 10),contact time(15;30 and 45 min),adsorbent mass(30;50 and 70 mg),and initial concentration(20;50 and 80 mg/L)of the adsorbate on the adsorption efficiency.The BBD was conducted using Google Colaboratory software,which encompassed 27 experiments with randomly assigned combinations.The silica gel synthesized from chemical glass bottle was characterized by XRD,FTIR,SEM-EDX and TEM.The adsorption result was measured by spectrophotometer UV-Vis.The optimized conditions resulted in a remarkable methylene blue removal efficiency of 99.41%.Characterization of the silica gel demonstrated amorphous morphology and prominent absorption bands characteristic of silica.The Langmuir isotherm model best described the adsorption behavior,revealing chemisorption with a monolayer coverage of methylene blue on the adsorbent surface,and a maximum adsorption capacity of 82.02 mg/g.Additionally,the pseudo-second-order kinetics model indicated a chemisorption mechanism during the adsorption process.The findings highlight the potential of silica gel from chemical glass bottle waste as a promising adsorbent for wastewater treatment,offering economic and environmental benefits.Further investigations can explore its scalability,regenerability,and reusability for industrial-scale applications.

Selective removal of 2,4-dichlorophenoxyacetic acid from water by molecularly-imprinted amino-functionalized silica gel sorbent

A molecularly-imprinted amino-functionalized sorbent for selective removal of 2,4-dichlorophenoxyacetic acid （2,4-D） was prepared by a surface imprinting technique in combination with a sol-gel process. The 2,4-D-imprinted amino-functionalized silica sorbent was characterized by FT-IR, nitrogen adsorption and static adsorption experiments. The selectivity of the sorbent was investigated by a batch competitive binding experiment using an aqueous 2,4-D and 2,4-dichlorophenol （2,4-DCP） mixture or using an aqueous 2,4-D and 2,4- dichlorophenylacetic acid （DPAC） mixture. The largest selectivity coefficient for 2,4-D in the presence of 2,4-DCP was found to be over 18, the largest relative selectivity coefficient between 2,4-D and 2,4-DCP over 9. The static uptake capacity and selectivity coefficient of the 2,4-D-imprinted functionalized sorbent are higher than those of the non-imprinted sorbent. The imprinted functionalized silica gel sorbent offered a fast kinetics for the extraction/stripping of 2,4-D, 73% of binding capacity （200 mg/L 2,4-D onto 20 mg of imprinted sorbent） was obtained within 5 min and the adsorbed 2,4-D can be easily stripped by the mixture solution of ethanol and 6 mol/L HC1 （V：V =1：1）. In a test of five extraction/stripping cycles, the adsorption capacity of the sorbent was all above 93% of that of the fresh sorbent. Experimental result showed the potential of molecularly-imprinted amino-functionalized sorbent for selective removal of 2,4-D.

Removal of siloxanes from biogas using acetylated silica gel as adsorbent

Biogas can be used as an alternative energy source for producing heat and electricity;however, volatile methylsiloxanes(VOSiC) present in biogas can severely damage heat exchangers, turbines and gas engines. Consequently, e cient removal of VOSiC from biogas that is used as a biofuel is required. In this work, acetylated silica gel(Ac@SG) was synthesized,via treatment of microporous silica gel(SG) with acetic anhydride as an adsorbent, for removal of VOSiC from biogas,and characterized with XRD, SEM–EDS, N2-BET and FT-IR. This Ac@SG adsorbent exhibited a meso-/microporous structure and hydrophobic surface, indicating it was a more e cient adsorbent for removing hexamethyldisiloxane(L2) and octamethylcyclotetrasiloxane(D4) from biogas samples than conventional SG. It was found that the adsorption capacities of Ac@SG reached 304 mg L2/g for hexamethyldisiloxane and 916 mg D4/g for octamethylcyclotetrasiloxane at lower temperatures in the experimental range, and water had no significant e ect on its absorption e ciency. The used Ac@SG could be easily regenerated by heating it at 110 °C, and the adsorption capacity of recycled Ac@SG for hexamethyldisiloxane and octamethylcyclotetrasiloxane was kept constant in four recycle adsorption experiments.

Preparation of organically functionalized silica gel as adsorbent for copper ion adsorption

A novel adsorbent （AMPS-silica） was synthesized by bounding AMPS （2-acrylamido-2-methylpropanesulfonic acid） onto silica surface, which functioned with γ-methacryloxypropyltrimethoxysilane reagent. The adsorbent was characterized by nitrogen adsorption/desorption measurement, thermogravimetric analysis （TGA） and potentiometric titration analysis. The TGA result indicated that the surface modification reactions introduced some organic functional groups onto the surface of silica. The surface area of AMPSsilica was 389.7 m2/g. The adsorbent was examined for copper ion removal in series of batch adsorption experiments. Results showed that the adsorption of Cu2＋ onto AMPS-silica was pH dependent, and the adsorption capacity increased with increasing pH from 2 to 6. The adsorption kinetics showed that Cu^2＋ adsorption was fast and the data fitted well with a pseudo secondorder kinetic model. The adsorption of Cu^2＋ onto AMPS-silica obeyed both Freundlich and Langmuir isotherms, with r^2 = 0.993 and r^2 = 0.984, respectively. The maximum Cu^2＋ adsorption capacity was 19.9 mg/g. The involved mechanism might be the adsorption through metal binding with organic functional groups such as carboxyl, amino and sulfonic groups. Cu^2＋ loaded on AMPS-silica could be desorbed in HNO3 solution, and the adsorption properties remain stable after three adsorption-desorption cycles.

Silica gel supported AlCl_3 catalyzed Friedel-Crafts acylation of aromatic compounds

Silica gel supported aluminium trichloride（SiO2-AlCl3） has been shown to be a mild,efficient,and chemoseiective heterogeneous Lewis acid catalyst for the acylation of aromatic compounds with acid chlorides.The catalyst can be reused up to five times after simple washing with ether and is stable（as a bench top catalyst）.

Efficient CO_2 capture on low-cost silica gel modified by polyethyleneimine

In this work, a series of polyethyleneimine （PEI） functionalized commercial silica gel were prepared by wet impregnation method and used as CO2 sorbent. The as-prepared sorbents were characterized by N2 adsorption, FT-1R and SEM techniques. CO2 capture was tested in a fixed bed reactor using a simulated flue gas containing 15.1% CO2 in a temperature range of 25-100 ~C. The effects of sorption temperature and amine content on CO2 uptake of the adsorbents were investigated. The silica gel with a 30 wt% PEI loading manifested the largest CO2 uptake of 93.4 mgcoz/gadsorbent （equal to 311.3 mg^oz/gPEI） among the tested sorbents under the conditions of 15.1% （v/v） CO2 in N2 at 75 ~C and atmospheric pressure. Moreover, it was rather low-cost. In addition, the PEI-impregnated silica gel exhibited stable adsorption-desorption behavior during 5 consecutive test cycles. These results suggest that the PEI-impregnated silica gel is a promising and cost-effective sorbent for CO2 capture from flue gas and other stationary sources with low CO2 concentration.

Separation and purification of deoxynivalenol(DON) mycotoxin from wheat culture using a simple two-step silica gel column chromatography

Deoxynivalenol（DON） is a type B trichothecenes mycotoxin produced by several Fusarium species, often found in foodstuffs for humans and animals. DON is in great demand for the toxicological researches both in vivo and in vitro. In this work, wheat culture was inoculated with a Fusarium graminearum PH-1 strain for DON production. The solvent system for crude extraction was acetonitrile-water（84：16, v/v）. A simple two-step silica gel column chromatography was employed to separate the DON mycotoxin from wheat culture, combined with preparative high performance liquid chromatography（preparative HPLC） to purify the compound. The solvent system for the second silica gel column chromatography was methylene chloride-methanol（17：1, v/v）, which provided a good elution effect selected on thin layer chromatography（TLC）. The target compound was identified by HPLC, and the chemical structure was confirmed by mass spectrometry（MS） and ~1H and ^（13）C nuclear magnetic resonance（NMR） spectroscopy. A total of 433 mg of purified DON was obtained from 1 kg of wheat culture, with a purity of 99.01%. The study had provided an easy-operating and cost-effective method to isolate an expensive compound in a simple way.

Synthesis of Hydroxypropyl-β-cyclodextrin Bonded Silica-gel and its Application to Resolution

In order to set up a simple and effective method for resolution of optical isomers, hydroxypropyl-β-cyclodextrin was bonded to silica-gel, which can be used for preparation of thin-layer chromatography plates. Resolution of clenbuterol and propranolol were investigated on these thin-layer chromatography plates using different combinations of solvent systems at ambient temperature. The best simultaneous resolution was achieved in solvent system of acetonitrilen-butanol （50：50, v/v）. Rst values of resolution of clenbuterol hydrochloride and propranolol hydrochloride are 3.6 and 4.3, respectively. The spots of different enantiomers are separated clearly. The results showed that hydroxypropyl-β-cyclodextrin bonded silica-gel could be successful in resolution of chiral adrenergic drugs. The study offers a direct, rapid and reliable method for separation of this kind of optically active compounds.

Preparation and Characterization of Silica Aerogels Derived from Ambient Pressure

Silica aerogels were prepared by sol-gel technique from industrial silicon derivatives （polyethoxydisiloxanes, E40）, followed by silylation and drying under ambient pressure. The specific surface area, pore size distribution and thermal conductivity of the silica aerogels were investigated and the results showed that the diameter of the silica particles is about 6 nm and the average pore size of the silica aerogels is 14.7 nm. The specific surface area of which is about 1000 m^2.g^-1 and the thermal conductivity is about 0.014 wm^-l.K^-1 at room temperature and pressure of 1.01×10^5 Pa. The Si-CH3 groups were also detected on the internal surface of the silica aerogels, which show hydrophobic. Silica aerogels derived by this technique is low cost and have wide applications.

Microstructure Control of Nanoporous Silica Thin Film Prepared by Sol-gel Process

Nanoporous silica films were prepared by sol-gel process with base, acid and base/acid two-step catalysis.Transmission electron microscope （TEM） and particle size analyzer were used to characterize the microstructure and the particle size distribution of the sols. Scanning electron microscopy （SEM）, atomic force microscopy （AFM） and spectroscopic ellipsometer were used to characterize the surface microstructure and the optical properties of the silica films. Stability of the sols during long-term storage was investigated. Moreover,the dispersion relation of the optical constants of the silica films, and the control of the microstructure and properties of the films by changing the catalysis conditions during sol-gel process were also discussed.

Silica-gel Supported V Complexes： Preparation, Characterization and Catalytic Oxidative Desulfurization

In this manuscript, a series of catalyst SG n-[VVO2-PAMAM-MSA] (SG silica gel, PAMAM polyamidoamine, MSA 5-methyl salicylaldehyde, n=0, 1, 2, 3) was prepared and their structures were fully characterized by Fourier transform-infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA), X-ray photoelectron spectroscopy (XPS) and inductive coupled plasma emission spectrometer (ICP) etc. XPS revealed that the metal V and SG n-PAMAM-MSA combined more closely after the formation of Schiff base derivatives. Their catalytic activities for oxidation of dibenzothiophene were evaluated using tert-butyl hydroperoxide as oxidant. The results showed that the catalyst SG 2.0-[VVO2-PAMAM-MSA] presented good catalytic activity and recycling time. Meanwhile, the optimal condition for the catalytic oxidation of SG 2.0-[VVO2-PAMAM-MSA] was also investigated, which showed that when the oxidation temperature was 90 °C, time was 60 min, the O/S was 3:1, and the mass content of catalyst was 1%, the rate of desulfurization could reach 85.2%. Moreover, the catalyst can be recycled several times without significant decline in catalytic activity.

SYNTHESIS OF MESOPOROUS POLY(STYRENE-co-MALEIC ANHYDRIDE)/SILICA HYBRID MATERIALS VIA A NONSURFACTANT-TEMPLATED SOL-GEL PROCESS

Mesoporous poly(styrene-co-maleic anhydride)/silica hybrid materials have been prepared. The synthesis was achieved by the HCl-catalyzed sol-gel reactions of tetraethyl orthosilicate (TEOS) and styrene-maleic anhydride copolymer in the presence of 3-aminopropyl triethoxysilane (APTES) as a coupling agent and citric acid as a nonsurfactant template or pore-forming agent, followed by ethanol extraction. Characterization results from nitrogen sorption isotherms and powder X-ray diffraction indicate that polymer-modified mesoporous materials with large specific surface areas (e.g. 900 m(2)/g) and pore volumes (e.g. 0.6 cm(3)/g) could be prepared. As the citric acid concentration is increased, the specific surface areas, pore volumes and pore diameters of the hybrid materials increase.

Mechanical Properties of Silica Aerogels Prepared from a Mixture of TEOS and Organo-alkoxysilanes of Type R_1SiX_3

Silica aerogels were prepared from a mixture of tetraethylorthosilicate and organo- alkoxysilanes. The effects of organo-alkoxysilanes on the mechanical properties of the silica aerogels were studied. The flexibility of silica aerogels was significantly improved by incorporation of organo-alkoxysilanes. When MTES and TEOS were combined as precursors of silica areogels, with the increased amount of MTES, the apparent elastic modulus and apparent compressive strength monotonously rose. At the same organo- alkoxysilanes to TEOS ratio, the size of alkyl groups of the organo-alkoxysilanes had little effect on the mechanical properties. In series of MTES and TEOS, the lowest elastic modulus of silica skeleton and the highest compressive strength of silica skeleton were observed at MTES to TEOS ratio of around 50：50. At a certain organo-alkoxysilanes to TEOS ratio, the elastic modulus of silica skeleton increased and the compressive strength of silica skeleton decreased with the size increase of the alkvl grouns.

Silica gel-assisted solvothermal production of CdS,Cu_xS (x=1,2) and ZnS with different morphologies

CdS, CuxS (x=1, 2) and ZnS with different morphologies were produced by the solvothermal reactions of M(CH3COO)2·2H2O (M=Cd, Cu and Zn) and NH2CSNH2 in hexane with and without silica gel as a hard template at 200 ℃ for 24 h. The product phases were detected using X-ray diffraction (XRD). Different morphologies were characterized using a scanning electron microscope (SEM). The existence of silica gel in modeling morphologies of the sulfides was characterized using Fourier transform infrared (FTIR) spectrometer. Raman spectra of different products show the vibrations at the same wavenumbers, although they are composed of different morphologies. Photoluminescence (PL) emissions of the corresponding phases with different morphologies are at the same values, but their intensities are increased by template adding.

Preparation and characterization of silica microcapsules containing butyl-stearate via sol-gel method

For thermal energy storage application in energy-saving building materials,silica microcapsules containing phase change material were prepared using sol-gel method in O/W emulsion system. In the system droplets in microns are formed by emulsifying an organic phase consisting of butyl-stearate as core material. The silica shell was formed via hydrolysis and condensation from tetraethyl silicate with acetate as catalyst. The SEM photographs show the particles possess spherical morphology and core-shell structure. The as-prepared silica microcapsules mainly consist of microsphere in the diameter of 3-7 μm and the median diameter of these microcapsules equals to 5.2 μm. The differential scanning calorimetry(DSC) curves indicate that the latent heat and the melting point of microcapsules are 86 J/g and 22.6 ℃,respectively. The results of DSC and TG further testify the microcapsules with core-shell structure.

Hierarchically Structured Monolithic ZSM-5 through Macroporous Silica Gel Zeolitization

The hierarchically structured ZSM-5 monolith was prepared through transforming the skeletons of the macroporous silica gel into ZSM-5 by the steam-assisted conversion method. The morphology and monolithic shapes of macroporous silica gel were well preserved. The hierarchically structured ZSM-5 monolith exhibited the hierarchical porosity, with mesopores and macropores existing inside the macroporous silica gel, and micropores formed by the ZSM-5. The products have been characterized properly by using the XRD, SEM and N2 adsorption–desorption methods.

PREPARATION AND CHARACTERIZATION OF SILICA GEL POWDERS

ＰＲＥＰＡＲＡＴＩＯＮＡＮＤＣＨＡＲＡＣＴＥＲＩＺＡＴＩＯＮＯＦＳＩＬＩＣＡＧＥＬＰＯＷＤＥＲＳＬｉＺｈｏｎｇｊｕｎＺｈａｏＱｉｎｓｈｅｎｇ（ＤｅｐａｒｔｍｅｎｔｏｆＮｏｎｆｅｒｒｏｕｓＭｅｔａｌｕｒｇｙ，ＣｅｎｔｒａｌＳｏｕｔｈＵｎｉｖｅｒｓｉｔｙ...

Separation and Purification of Acetophenones from Cynanchum bengei Decne Root Bark by Combination of Silica Gel and High-speed Counter-current Chromatography

[Objectives] To develop a method for separation and purification of acetophenones from Cynanchum bengei Decne root bark by combination of silica gel and high-speed counter-current chromatography( HSCCC). [Methods]The crude extract of Cynanchum bengei Decne root bark was separated by silica gel column chromatography,and parts A and B containing acetophenones were obtained. Then,parts A and B were separated by HSCCC with a two-phase solvent system composed of petroleum ether-ethyl acetate-methanol-water( 4∶ 6∶ 4. 5∶ 5. 5 and4∶ 6 ∶ 3 ∶ 7, V/V), respectively. [Results] From 260 mg of part A, four compounds with p-dihydroxybenzene 3. 9 mg(Ⅰ),4-hydroxyacetophenone 17. 1 mg( Ⅱ),2,5-di-hydroxyacetophenone 13. 3 mg(Ⅲ) and 2,4-dihydroxyaceto-phenone 21. 0 mg(Ⅳ) were obtained. And from 300 mg of part B,136 mg of Radix Cynanchi Bungei benzophenone(Ⅴ) was obtained. The purity of compounds determined by HPLC was 97. 0%,96. 6%,99. 2%,99. 7%,99. 5%,respectively. [Conclusions] The established method is simple and efficient. It can be used for separation of acetophenones from Cynanchum bengei Decne root bark and has better practical value,which could provide a reference basis for development and utilization of Cynanchum bengei Decne root bark.