Upconversion Emission in Er^(3+) Doped Novel Bismuthate Glass

Novel Er3+-doped bismuth lead strontiam glass was fabricated and characterized, and the absorption spectrum and upconversion spectrum of the glass were studied. The Judd-Ofelt intensity parameters Ωt (t=2, 4, 6) were found to be Ω2=3.27×10-20 cm2, Ω4=1.15×10-20 cm2, and Ω6=0.38×10-20 cm2. The oscillator strength, the spontaneous transition probabilities, the fluorescence branching ratios, and excited state lifetimes were also measured and calculated. The upconversion emission intensity varies with the power of infrared excitation intensity. A plot of log Iup vs log IIR yields a straight line with slope 1.86, 1.88 and 1.85, corresponding to 525, 546, and 657 nm emission bands, respectively, which indicates that a two-photon process for the red and green emission.

超声引导下PTCD应用于BismuthⅢ型胆道梗阻患者临床对照研究

目的探讨超声引导下的经皮肝穿刺胆道引流术(PTCD)应用于BismuthⅢ、Ⅳ型胆道梗阻患者的临床疗效。方法将95例恶性胆道梗阻患者中的BismuthⅢ型患者65例设为Ⅲ型组,BismuthⅣ型患者30例设为Ⅳ型组。比较两组患者手术时间、临床疗效及术后并发症发生情况,比较治疗前后肝功能指标[丙氨酸氨基转移酶(ALT)、天门冬氨酸氨基转移酶(AST)、谷氨酰转肽酶(GGT)、碱性磷酸酶(ALP)、总胆红素(TBIL)和直接胆红素(DBIL)]水平及癌症患者生命质量测定量表(QLQ-C30)评分。结果Ⅲ型组患者手术时间短于Ⅳ型组,治疗总有效率高于Ⅳ型组(P<0.05或0.01)。治疗后两组患者血清ALT、AST、GGT、ALP、TBIL和DBIL水平均较治疗前降低,且Ⅲ型组低于Ⅳ型组(P<0.05或0.01)。治疗后两组患者QLQ-C30的总体健康状况、躯体功能、角色功能、情绪功能、认知功能、社会功能、疲乏、恶心呕吐、疼痛、呼吸困难、睡眠障碍、食欲丧失、便秘维度评分均较治疗前改善,Ⅲ型组患者QLQ-C30的总体健康状况、躯体功能、情绪功能、社会功能维度评分高于Ⅳ型组,而疲乏、恶心呕吐、疼痛、呼吸困难、睡眠障碍、食欲丧失、便秘维度评分低于Ⅳ型组(P<0.05或0.01)。Ⅲ型组患者术后并发症发生率低于Ⅳ型组,但差异无统计学意义(P>0.05)。结论相较于BismuthⅣ型胆道梗阻,超声引导下的PTCD应用于BismuthⅢ型胆道梗阻患者有较好的疗效,可以改善患者肝功能和生存质量。

Solid Bi_(2)O_(3)-derived nanostructured metallic bismuth with high formate selectivity for the electrocatalytic reduction of CO_(2)

CO_(2) electrochemical reduction(CO_(2)ER)is an important research area for carbon neutralization.However,available catalysts for CO_(2) reduction are still characterized by limited stability and activity.Recently,metallic bismuth(Bi)has emerged as a promising catalyst for CO_(2) ER.Herein,we report the solid cathode electroreduction of commercial micronized Bi2O3as a straightforward approach for the preparation of nanostructured Bi.At-1.1 V versus reversible hydrogen electrode in a KHCO3aqueous electrolyte,the resulting nanostructure Bi delivers a formate current density of~40 mA·cm^(-2) with a current efficiency of~86%,and the formate selectivity reaches97.6% at-0.78 V.Using nanosized Bi2O3as the precursor can further reduce the primary particle sizes of the resulting Bi,leading to a significantly increased formate selectivity at relatively low overpotentials.The high catalytic activity of nanostructured Bi is attributable to the ultrafine and interconnected Bi nanoparticles in the nanoporous structure,which exposes abundant active sites for CO_(2) electrocatalytic reduction.

Systematic engineering of BiVO_(4)photoanode for efficient photoelectrochemical water oxidation

BiVO_(4)is one of the most promising photoanode materials for photoelectrochemical(PEC)solar energy conversion,but it still suffers from poor photocurrent density due to insufficient light‐harvesting efficiency(LHE),weak photogenerated charge separation efficiency(Φ_(Sep)),and low water oxidation efficiency(Φ_(OX)).Herein,we tackle these challenges of the BiVO_(4)photoanodes using systematic engineering,including catalysis engineering,bandgap engineering,and morphology engineering.In particular,we deposit a NiCoO_(x)layer onto the BiVO_(4)photoanode as the oxygen evolution catalyst to enhance theΦ_(OX)of Fe‐g‐C_(3)N_(4)/BiVO_(4)for PEC water oxidation,and incorporate Fe‐doped graphite‐phase C_(3)N_(4)(Fe‐g‐C_(3)N_(4))into the BiVO_(4)photoanode to optimize the bandgap and surface areas to subsequently expand the light absorption range of the photoanode from 530 to 690 nm,increase the LHE andΦ_(Sep),and further improve the oxygen evolution reaction activity of the NiCoO_(x)catalytic layer.Consequently,the maximum photocurrent density of the as‐prepared NiCoO_(x)/Fe‐g‐C_(3)N_(4)/BiVO_(4)is remarkably boosted from 4.6 to 7.4 mA cm^(−2).This work suggests that the proposed systematic engineering strategy is exceptionally promising for improving LHE,Φ_(Sep),andΦ_(OX)of BiVO_(4)‐based photoanodes,which will substantially benefit the design,preparation,and large‐scale application of next‐generation high‐performance photoanodes.

Efficient Preparation and Electrochemical Properties of BiOCl/Graphite by One-step Solvothermal Method

We used the surface-pretreated graphite paper(Gp)as a carrier and loaded BiOCl with high selectivity to Cl^(-)on its surface by solvothermal method to form BiOCl@Gp electrode.The morphology,structure,and composition of the materials were characterized by scanning electron microscopy and nitrogen adsorption/desorption,and the results showed that the spherical BiOCl particles were uniformly dispersed on the surface of the Gp,forming a mesoporous BiOCl@Gp composite with a specific surface area of 22.82 m^(2)/g and a pore volume of 0.043 cm3/g.Furthermore,cyclic voltammetry and electrochemical impedance spectroscopy were used to test the electrochemical properties of the composites,and the stability of BiOCl and the high conductivity of Gp were synergistic,the BiOCl@Gp exhibited a specific capacitance of 30.2 F·g^(-1) at a current density of 0.5 A·g^(-1),and the selectivity of the BiOCl@Gp materials for Cl^(-)was significantly higher than that of SO_(4)^(2-),NO_(2)^(-),and HCO_(3)^(-).Therefore,BiOCl@Gp composite electrode materials can be used for the selective adsorption of Cl^(-)in wastewater,in order to achieve efficient wastewater recycling.

2D black arsenic phosphorous

Since the successful exfoliation of graphene in 2014,twodimensional(2D)materials have explosively increased in the past few years[1].2D pnictogen materials with intriguing properties beyond graphene are gradually coming into eyesight,such as black phosphorous(BP)[2],arsenene[3],antimonene[4],bismuthine[5],etc.BP is a star material in 2D materials.

Kinetic-boosted CO_(2) electroreduction to formate via synergistic electric-thermal field on hierarchical bismuth with amorphous layer

Electrocatalytic converting CO_(2) into chemical products has emerged as a promising approach to achieving carbon neutrality.Herein,we report a bismuth-based catalyst with high curvature terminal and amorphous layer which fabricated via two-step electrodeposition achieves stable formate output in a wide voltage window of 600 mV.The Faraday efficiency(FE) of formate reached up to 99.4% at-0.8 V vs.RHE and it remained constant for more than 92 h at-15 mA cm^(-2).More intriguingly,FE formate of95.4% can be realized at a current density of industrial grade(-667.7 mA cm^(-2)) in flow cell.The special structure promoted CO_(2) adsorption and reduced its activation energy and enhanced the electric-thermal field and K^(+) enrichment which accelerated the reaction kinetics.In situ spectroscopy and theoretical calculation further confirmed that the introduction of amorphous structure is beneficial to adsorpting CO_(2)and stabling*OCHO intermediate.This work provides special insights to fabricate efficient electrocatalysts by means of structural and crystal engineering and makes efforts to realize the industrialization of bismuth-based catalysts.

In situ observation of the phase transformation kinetics of bismuth during shock release

A time-resolved x-ray diffraction technique is employed to monitor the structural transformation of laser-shocked bismuth.Results reveal a retarded transformation from the shock-induced Bi-Ⅴphase to a metastable Bi-Ⅳphase during the shock release,instead of the thermodynamically stable Bi-Ⅲphase.The emergence of the metastable Bi-Ⅳphase is understood by the competitive interplay between two transformation pathways towards the Bi-Ⅳand Bi-Ⅲ,respectively.The former is more rapid than the latter because the Bi-Ⅴto B-Ⅳtransformation is driven by interaction between the closest atoms while the Bi-Ⅴto B-Ⅲtransformation requires interaction between the second-closest atoms.The nucleation time for the Bi-Ⅴto Bi-Ⅳtransformation is determined to be 5.1±0.9 ns according to a classical nucleation model.This observation demonstrates the importance of the formation of the transient metastable phases,which can change the phase transformation pathway in a dynamic process.

Growth and characterization of Bi(110)/CrTe_(2) heterostructures:Exploring interplay between magnetism and topology

The interplay between topology and magnetism is vital for realizing exotic quantum phenomena,significant examples including quantum anomalous Hall effect,axion insulators,and high-order topological states.These states host great potential for future applications in high-speed and low-consumption electronic devices.Despite being extensively investigated,practical platforms are still scarce.In this work,with molecular beam epitaxy(MBE),we provide the first experimental report on high-quality Bi(110)/CrTe_(2) magnetic heterostructure.By employing in-situ high-resolution scanning tunneling microscopy,we are able to examine the interaction between magnetism and topology.There is a potential edge state at an energy level above the Fermi level,but no edge states observed near the Fermi level The absence of high-order topological corner states near EF highlights the importance of lattice matching and interface engineering in designing high-order topological states.Our study provides key insights into the interplay between two-dimensional magnetic and topological materials and offers an important dimension for engineering magnetic topological states.

Soil Profile Concentration Distributions of Antimony and Bismuth across Southeastern Missouri (USA)

Recent research has suggested that increased industrial and technological utilization of antimony and bismuth necessitates greater research to determine the soil and water chemistry and the environmental risks associated with these elements. The near-total soil profile concentrations of antimony and bismuth were determined for key soil series across southeastern Missouri. The antimony concentrations ranged from 0.65 to 0.08 mg kg−1, whereas the bismuth soil profile concentrations ranged from 0.92 to 0.03 mg kg−1. Most pedons showed antimony concentrations ranging from 20 to 30 mg kg−1, whereas bismuth concentrations were commonly 10 to 20 mg kg−1. For soils having argillic horizons, antimony and bismuth concentrations were greater for the illuvial horizons than the eluvial horizons, whereas Entisols, Inceptisols, and one Vertisol showed rather uniform antimony and bismuth concentrations, features paralleling the soil texture distribution. Both antimony and bismuth showed significant correlations with iron.

Effect of Bismuth Subgallate/Borneol Combined with Autologous Platelet-Rich Gel in the Treatment of Patients with Diabetic Foot Ulcers

Objective: To explore the effect of Bismuth Subgallate/Borneol (SuileTM BSB) healing dressing combined with autologous platelet-rich gel (APG) in the treatment of diabetic foot ulcer (DFU). Methods: A total of 120 patients with DFU hospitalized in the Changsha Central Hospital from August 2020 to September 2021 were selected and randomly divided into an experimental group (BSB + APG, n = 60) and a control group (BSB, n = 60) according to random number table method. The total therapeutic effect, healing time, hospital stay, level indexes of various inflammatory factors before and after treatment and ulcer area were observed in the two groups. Results: The total effect of the control group was worse than that of the experimental group, and the data between the two groups were significant (P 0.05);after treatment, the levels of inflammatory factors including WBC, CRP, IL-6 and TNF-α in the control group were higher than those in the experimental group, and there was significant difference between the two groups (P 0.05);after 14 days of treatment, the ulcer area in the control group was larger than that in the experimental group, and the data between the two groups were significant (P Conclusion: BSB combined with APG can achieve better therapeutic effect, reduce the inflammatory reaction of patients, and promote wound healing in the treatment of patients with diabetic foot ulcer.

Effective ethanol-to-CO_(2) electrocatalysis at iridium-bismuth oxide featuring the impressive negative shifting of the working potential

Since low overpotential for the anodic ethanol oxidation reaction(EOR)can favor the higher output voltage and power of direct ethanol fuel cells(DEFCs),it is critical to design new EOR catalysts with efficient ethanol-to-CO_(2)activity at low applied potentials.Thereby,carbon-supported Ir-Bi_(2)O_(3)(Ir-Bi_(2)O_(3)/C)catalysts with highly dispersive bismuth oxide on the iridium surface are designed and prepared,which can merit splitting the ethanol C–C bond and promoting the oxidation of C1 intermediates at the bifunctional interfaces.The as-obtained Ir-Bi2O3/C catalysts show superior EOR mass activity of up to ca.2250 m A mgIr-1.Moreover,they exhibit the record lowest onset oxidation potentials(0.17–0.22 V vs.RHE)and the peak potential(ca.0.58 V vs.RHE),being 130–300 m V lower than the previous landmark noble metallic catalysts.Furthermore,an apparent C1 pathway faraday efficiency(FEC1)of 28%±5.9%at 0.5 V vs.RHE can be obtained at Ir-Bi_(2)O_(3)/C.This work might provide new insights into the new anodic EOR catalysts for increasing the power of DEFCs.

Preparation of Y^(3+)-doped Bi-_(2)MoO_(6) nanosheets for improved visible-light photocatalytic activity: Increased specific surface area, oxygen vacancy formation and efficient carrier separation

Although Bi_(2)Mo O_(6)(BMO) has recently received extensive attention, its visible-light photocatalytic activity remains poor due to its limited photoresponse range and low charge separation efficiency. In this work, a series of visible-light-driven Y^(3+)-doped BMO(Y-BMO) photocatalysts were synthesized via a hydrothermal method. Degradation experiments on Rhodamine B and Congo red organic pollutants revealed that the optimal degradation rates of Y-BMO were 4.3 and 5.3 times those of pure BMO, respectively. The degradation efficiency of Y-BMO did not significantly decrease after four cycle experiments. As a result of Y^(3+)doping, the crystal structure of BMO changed from a thick layer structure to a thin flower-like structure with an increased specific surface area. X-ray photoelectron spectroscopy showed the presence of highintensity peaks for the O 1s orbital at 531.01 and 530.06 eV, confirming the formation of oxygen vacancies in Y-BMO. Photoluminescence(PL) and electrochemical impedance spectroscopy measurements revealed that the PL intensity and interface resistances of composites decreased significantly, indicating reduced electron–hole pair recombination. This work provides an effective way to prepare high-efficiency Bibased photocatalysts by doping rare earth metal ions for improved photocatalytic performance.

Self-adaptive bulk/surface engineering of Bi_(x)O_(y)Br_(z) towards enhanced photocatalysis:Current status and future challenges

The bulk/surface states of semiconductor photocatalysts are imperative parameters to maneuver their performance by significantly affecting the key processes of photocatalysis including light absorption,separation of charge carrier,and surface site reaction.Recent years have witnessed the encouraging progress of self-adaptive bulk/surface engineered Bi_(x)O_(y)Br_(z) for photocatalytic applications spanning various fields.However,despite the maturity of current research,the interaction between the bulk/surface state and the performance of Bi_(x)O_(y)Br_(z) has not yet been fully understood and highlighted.In this regard,a timely tutorial overview is quite urgent to summarize the most recent key progress and outline developing obstacles in this exciting area.Herein,the structural characteristics and fundamental principles of Bi_(x)O_(y)Br_(z)for driving photocatalytic reaction as well as related key issues are firstly reviewed.Then,we for the first time summarized different self-adaptive engineering processes over Bi_(x)O_(y)Br_(z)followed by a classification of the generation approaches towards diverse Bi_(x)O_(y)Br_(z)materials.The features of different strategies,the up-to-date characterization techniques to detect bulk/surface states,and the effect of bulk/surface states on improving the photoactivity of Bi_(x)O_(y)Br_(z)in expanded applications are further discussed.Finally,the present research status,challenges,and future research opportunities of self-adaptive bulk/surface engineered Bi_(x)O_(y)Br_(z)are prospected.It is anticipated that this critical review can trigger deeper investigations and attract upcoming innovative ideas on the rational design of Bi_(x)O_(y)Br_(z)-based photocatalysts.

Efficacy and safety of modified tetracycline dosing in a quadruple therapy for Helicobacter pylori:A retrospective single center study

BACKGROUND Although highly effective as a component of Helicobacter pylori(H.pylori)treatment regimen,tetracycline is associated with a high incidence of medicationrelated adverse events.Modified dosing of tetracycline as part of quadruple therapy may improve safety while providing comparable eradication rates.AIM To evaluate the efficacy and safety of modified dosing of tetracycline in patients receiving tetracycline and furazolidone-containing quadruple therapy in patients with H.pylori infection.METHODS Consecutive patients(10/2020-12/2021)who received tetracycline and furazolidone quadruple therapy for H.pylori infection at Sir Run Run Shaw Hospital were identified.All patients received tetracycline,furazolidone,proton pump inhibitor,and bismuth for 14 d as primary or rescue therapy.Modified tetracycline dose group received tetracycline 500 mg twice daily while standard group received 750 mg twice daily or 500 mg three times daily.RESULTS Three hundred and ninety-four patients[mean age=46.3±13.9,male=137(34.8%),and 309(78.4%)primary therapy]completed tetracycline and furazolidone quadruple therapy for H.pylori infection including those who received modified tetracycline dose in 157 and standard doses in 118(750 mg twice daily)and 119(500 mg three times daily).Eradication rates in the modified tetracycline dose group were 92.40%and in the standard groups,eradication rates were 93.20%for 750 mg twice daily group and 92.43%for 500 mg three times daily group,respectively,without statistical difference(P=0.959).The incidence of adverse events was lower in the modified tetracycline dose(15.3%vs 32.3%and 29.4%;P=0.002)compared to the standard dose group.CONCLUSION In a real-world experience,modified tetracycline dosing as part of tetracycline and furazolidone quadruple therapy for 14 d demonstrated high efficacy,comparable to standard tetracycline dose regimens,with a favorable safety profile.

Bi nanoparticles encapsulated in nitrogen-doped carbon as a long-life anode material for magnesium batteries

Bismuth has garnered significant interest as an anode material for magnesium batteries(MBs) because of its high volumetric specific capacity and low working potential. Nonetheless, the limited cycling performance(≤100 cycles) limits the practical application of Bi as anode for MBs. Therefore, the improvement of Bi cycling performance is of great significance to the development of MBs and is also full of challenges. Here, Bi nanoparticles encapsulated in nitrogen-doped carbon with single-atom Bi embedded(Bi@NC) are prepared and reported as an anode material for MBs. Bi@NC demonstrates impressive performance, with a high discharge capacity of 347.5 mAh g^(-1) and good rate capability(206.4 mAh g^(-1)@500 mA g^(-1)) in a fluoride alkyl magnesium salt electrolyte. In addition, Bi@NC exhibits exceptional long-term stability, enduring 400 cycles at 500 mA g^(-1). To the best of our knowledge, among reported Bi and Bi-based compounds for MBs, Bi@NC exhibits the longest cycle life in this work. The magnesium storage mechanism of Bi@NC is deeply studied through X-ray diffraction, transmission electron microscopy and X-ray photoelectron spectroscopy. This work provides some guidance for further improving the cycling performance of other alloy anodes in MBs.

Recent advances in bismuth-based photocatalysts:Environment and energy applications

Photocatalysis is an effective way to solve the problems of environmental pollution and energy shortage.Numerous photocatalysts have been developed and various strategies have been proposed to improve the photocatalytic performance.Among them,Bi-based photocatalysts have become one of the most popular research topics due to their suitable band gaps,unique layered structures,and physicochemical properties.In this review,Bi-based photocatalysts(BiOX,BiVO_(4),Bi_(2)S_(3),Bi_(2)MoO_(6),and other Bi-based photocatalysts)have been summarized in the field of photocatalysis,including their applications of the removal of organic pollutants,hydrogen production,oxygen production etc.The preparation strategies on how to improve the photocatalytic performance and the possible photocatalytic mechanism are also summarized,which could supply new insights for fabricating high-efficient Bi-based photocatalysts.Finally,we summarize the current challenges and make a reasonable outlook on the future development direction of Bi-based photocatalysts.

Tailored BiVO_(4)/In_(2)O_(3)nanostructures with boosted charge separation ability toward unassisted water splitting

The development of new heterostructures with high photoactivity is a breakthrough for the limitation of solar-driven water splitting.Here,we first introduce indium oxide(In_(2)O_(3))nanorods(NRs)as a novel electron transport layer for bismuth vanadate(BiVO_(4))with a short charge diffusion length.In_(2)O_(3)NRs reinforce the electron transport and hole blocking of BiVO_(4),surpassing the state-of-the-art photoelectrochemical performances of BiVO_(4)-based photoanodes.Also,a tannin-nickel-iron complex(TANF)is used as an oxygen evolution catalyst to speed up the reaction kinetics.The final TANF/BiVO_(4)/In_(2)O_(3)NR photoanode generates photocurrent densities of 7.1 mAcm^(−2) in sulfite oxidation and 4.2 mA cm^(−2) in water oxidation at 1.23 V versus the reversible hydrogen electrode.Furthermore,the“artificial leaf,”which is a tandem cell with a perovskite/silicon solar cell,shows a solar-to-hydrogen conversion efficiency of 6.2%for unbiased solar water splitting.We reveal significant advances in the photoactivity of TANF/BiVO_(4)/In_(2)O_(3)NRs from the tailored nanostructure and band structure for charge dynamics.

One-photo excitation pathway in 2D in-plane heterostructures for effective visible-light-driven photocatalytic degradation

Broad-spectrum absorption and highly effective charge-carrier separation are two essential requirements to improve the photocatalytic performance of semiconductor-based photocatalysts.In this work,a fascinating one-photon system is reported by rationally fabricating 2D in-plane Bi_(2)O_(3)/BiOCl(i-Cl)heterostructures for efficient photocatalytic degradation of RhB and TC.Systematic investigations revealed that the matched band structure generated an internal electric field and a chemical bond connection between the Bi_(2)O_(3)and BiOCl in the Bi_(2)O_(3)/BiOCl composite that could effectively improve the utilization ratio of visible light and the separation effectivity of photo-generated carriers in space.The formed interactions at the 2D in-plane heterojunction interface induced the one-photon excitation pathway which has been confirmed by the experiment and DFT calculations.As a result,the i-Cl samples showed significantly enhanced photocatalytic efficiency towards the degradation of RhB and TC(RhB:0.106 min^(-1);TC:0.048 min^(-1))under visible light.The degradation activities of RhB and TC for i-Cl were 265.08 and 4.08times that of pure BiOCl,as well as 9.27 and 2.14 times that of mechanistically mixed Bi_(2)O_(3)/BiOCl samples,respectively.This work provides a logical strategy to construct other 2D in-plane heterojunctions with a one-photon excitation pathway with enhanced performance.

Metal-organic-frameworks passivated CuBi_(2)O_(4)photocathodes boost CO_(2)reduction kinetics

Photoelectrochemical reduction of CO_(2)to produce CO with metal-organic frameworks(MOFs)is recognized as a desirable technology to mitigate CO_(2)emission and generate sustainable energy.To achieve highly efficient electrocatalyst,it is essential to design a new material interface and uncover new reaction mechanisms or kinetics.Herein,we developed two metal-organic Cu-MOF and Bi-MOF layers using benzene tricarboxylic acid(H_(3)BTC)ligands on CuBi_(2)O_(4) photocathodes.Both MOF layers drastically improved the photoelectrochemical stability by suppressing the photo-corrosion through conformal surface passivation.The Cu-MOF modified CuBi_(2)O_(4) showed more significant charge separation and transfer efficiencies than the Bi-MOF modified control.Based on the transient photocurrent curves under the applied potential of 0.6 V vs.RHE,the rate-law analysis showed the CO_(2)photoreduction took place through a first-order reaction.Further,the photoelectrochemical impedance spectra(PEIS)revealed this reaction order,representing an“operando”analysis.Moreover,the reaction rate constant on Cu-MOF modified sample was higher than that on Bi-MOF modified one and bare CuBi_(2)O_(4).Combined with the density functional theory calculation,the surface absorption of CO_(2)and CO molecules and the higher energy barrier for*COOH intermediates could significantly determine the first order reaction.