Precipitation of spherical boehmite from concentrated sodium aluminate solution by adding gibbsite as seed

The precipitation of spherical boehmite was studied by surface energy calculations, measurements of precipitation ratios, Fourier transform infrared spectroscopy, X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. The surface energy calculation results show that the(001) and(112) planes of gibbsite surfaces are remarkably stable because of their low surface energies. In addition, the(010) plane of boehmite grows preferentially during precipitation because of its low surface energy. Thus, we propose a method to precipitate spherical boehmite from a supersaturated sodium aluminate solution by adding gibbsite as seed in a heterogeneous system. In this method, gibbsite acts as the preliminary seed and saturation modifier. The results show that the fine boehmite first nucleates on the(001) and(112) planes of gibbsite and then grows vertically on the(001) and(112) basal planes of gibbsite via self-assembly, thereby forming spherical boehmite. Simultaneously, gibbsite is dissolved into the aluminate solution to maintain the saturation for the precipitation of boehmite. The precipitation ratio fluctuates(forming an M-shaped curve) because of gibbsite dissolution and boehmite precipitation. The mechanism of boehmite precipitation was further discussed on the basis of the differences in surface energy and solubility between gibbsite and boehmite. This study provides an environmentally friendly and economical method to prepare specific boehmite in a heterogeneous system.

Influence of hydrothermal temperature on structure and microstructure of boehmite

Boehmites(Al2O3·xH2O)were hydrothermally prepared from aluminum alkoxide.The effect of temperature on preparation was studied in the range of 100-180℃.The XRD analysis shows that with temperature increasing,the transformation of pseudo-boehmite into well-crystallized boehmite takes place.The micro-morphologies change also from irregular clew to thin cubic platelets.From the mass loss of the samples prepared at different temperatures,the value of x is estimated to vary between 1.06 and 1.67.γ-Al2O3 obtained by subsequent calcination of boehmite at 600℃is also characterized by XRD and its morphology remains unchanged.

Solvothermal Synthesis of Boehmite and γ-Alumina Nanorods

Boehmite nanorods were synthesized by a solvothermal method using AICl3·6H2O in mixed solvents of water and aniline. The solvothermal time, heating temperature and the concentration of aniline have effects on the morphology of boehmite. γ-alumina nanorods were prepared by a simple thermal transformation of boehmite nanorods. A rational mechanism based on the oriented attachment is proposed for the formation of boehmite nanorods. The products were characterized by X-ray powder diffraction （XRD） and transmission electron microscopy （TEM）. Photoluminescence （PL） spectrum of the boehmite nanorods was also investigated.

Influence of Nanoparticle Shapes of Boehmite Alumina on the Thermal Performance of a Straight Microchannel Printed Circuit Heat Exchanger

The efficiency and irreversibility defined based on the second law of thermodynamics provide a new path for heat exchangers design and make performance analysis more straightforward and elegant.The second law of thermodynamics is applied in a Straight Microchannel Printed Circuit heat exchanger to determine the thermal performance of different shapes of Boehmite Alumina compared to Al2O3 aluminum oxide.The various forms of non-spherical Boehmite Alumina are characterized dynamically and thermodynamically through dynamic viscosity and thermal conductivity,using empirical coefficients.The non-spherical shape includes platelet,cylindrical,blades,and bricks forms.Graphical results are presented for thermal efficiency,thermal irreversibility,heat transfer rate,and nanofluid exit temperature.The non-spherical shapes of Boehmite Alumina show different thermal characteristics concerning the spherical shape when there are variations in fluid flow rates and the nanoparticles fraction.Furthermore,it was theoretically demonstrated that non-spherical particles have higher heat transfer rates than spherical particles,emphasizing platelets and cylindrical shapes for the low volume fraction of nanoparticles and bricks and blades for high volume fraction.

Formation of CoAl layered double hydroxide on the boehmite surface and its role in tungstate sorption

Sorption of tungstate on boehmite（γ-Al OOH）is increased by co-sorption with Co^（2＋）over the near-neutral p H range.Batch uptake experiments show up to a 3-fold increase in tungstate uptake over the range WO4^（2-）=50–1000μmol/L compared to boehmite not treated with Co^（2＋）.Desorption experiments reveal a corresponding decrease in sorption reversibility for tungstate co-sorbed with Co^（2＋）.Reaction of boehmite with Co^（2＋）results in the formation of Co Al layered double hydroxide（LDH）,as confirmed by X-ray diffraction and X-ray absorption spectroscopy.Tungsten L3-edge X-ray absorption near edge structure（XANES）reveals that W（VI）is octahedrally coordinated in all sorption samples,with polymeric tungstate species forming at higher tungstate concentrations.X-ray diffraction and X-ray absorption spectroscopy indicate that the mechanism for enhancement of tungstate uptake is the formation of surface complexes on boehmite at low tungstate concentrations,while exchange into the Co Al LDH becomes important at higher tungstate concentrations.The results provide a basis for developing strategies to enhance tungstate sorption and to limit its environmental mobility at near-neutral pH conditions.

Solvothermal preparations of α-alumina and boehmite crystallites and investigations on the formation of their morphologies

The solvothermal preparations of α alumina and boehmite crystallites have been investigated, and the effects of solvothermal conditions such as reactive medium and temperature on the phase, crystallization morphology and size of the crystallites have been discussed. The calculation of the stability energies of the growth units of the crystallites has been performed based on the model of anion coordinate polyhedron’s growth unit. The results could explain the formation mechanisms of the crystallites.

Preparation and Phase Transformation Behavior of Boehmite via Heat Treatment in Water Vapor

Boehmite was prepared under heat treatment in water vapour, and the phase transformation of gibbsite heat-treated at various temperatures was investigated. The sample was characterized by scanning electron microscopy(SEM), X-ray diffraction (XRD), thermogravimetry and differential thermalanalysis (TG-DTA), fourier transform infrared (FTIR),and BET surface area.Effect of temperature on preparation was studied in the range of 155°–195°.With the increase in temperature, transformation of gibbsite into crystalline boehmites took place as indicated by the X-ray diffraction (XRD). The shape of the grains in the prepared sample was cube-like morphology.In water vapour gibbsite transform into boehmite by a dissolution - precipitation mechanism.

Pristine point of zero charge (p.p.z.c.) and zeta potentials of boehmite’s nanolayer and nanofiber surfaces

The pristine point of zero charge(p.p.z.c)and zeta potential as a function of pH of boehmite oxide/hydroxide(α-Al_(2)O_(3)·H_(2)O)have been determined for three filter media.The active component in the first two filter media is boehmite nanofibers,only 2 nm in diameter and about 300 nm long.Boehmite nanofibers create high zeta potential(ζtrue≥46 mV)in aqueous solutions in the pH range of 3–8.The p.p.z.c.values were determined to be 11.60±0.15 for nanofibers grafted onto microglass fibers and 11.40±0.15 for agglomerated nanofibers.In the third filter media,a boehmite nanolayer in the form of monocrystalline oxide/hydroxide with a thickness of approximately 1.2 nm is electroadhesively deposited onto siliceous support material with large surface area of about 50 m^(2)/g,therefore forming a highly electropositive composite of boehmite nanolayer on the second highly electronegative solid.Boehmite’s oxide-hydroxide nanolayer surface creates high zeta potential(ζtrue≥50 mV)in aqueous solutions in the pH range of 3–8.The p.p.z.c.value was determined to be 11.38±0.15.The reported values are within accuracy,but they are much higher than the values reported in the literature.X-ray powder diffraction data were supplemented by microscopy,infrared spectroscopy in order to characterize fully synthetic boehmite surfaces.

Synthesization and crystallization mechanism of nano-scale γ-AlOOH with various morphologies

Nano-scale γ-AIOOH with various morphologies, such as whisker, bar, ball, and sheet, was synthesized successfully and control- lably through a facile hydrothermal method just by adjusting the pH value of the solvent. Based on the analysis of the experimental data, the growth mechanism of nano-scale γ-AlOOH in the hydrothermal process was established. It is proposed that the growth unit and the growth direction are determined by the pH value of the solution and the growth unit, respectively. One-dimensional γ-AlOOH, such as whisker and bar, is formed in lower pH ranges, while two-dimensional γ-AlOOH sueli as sheet is formed only in high pH environment following the plane expansion crystallization mechanism.

载体改性及其对负载型Fe催化剂降解苯酚废水性能的影响

采用聚乙二醇(Polyethylene glycol,PEG)改性的Boehmite为载体,利用浸渍法制备了Fe为活性组分的负载型催化剂。考察了催化剂对苯酚废水降解的催化活性,并通过SEM、BET以及XRD等技术手段对改性前后的Boehmite进行了表征。结果表明,改性后的Boehmite比表面积及孔体积都有所增大,孔径分布更加集中。催化剂活性显示:利用改性Boehmite所制得的Fe/PEG-Boehmite催化剂在苯酚废水降解过程中活性优于没有利用PEG改性的催化剂,二者在反应60 min后对苯酚废水化学需氧量(Chemical demand oxygen,COD)去除率分别为93%和67%。因此,对于活性组分含量相同的催化剂而言,PEG对Boehmite载体的改性有助于所制备催化剂对苯酚废水COD去除率的提高。

Rehydration and Phase Transformation of Aluminas

ＲｅｈｙｄｒａｔｉｏｎａｎｄＰｈａｓｅＴｒａｎｓｆｏｒｍａｔｉｏｎｏｆＡｌｕｍｉｎａｓＺｈａｎｇＭｉｎｇｈａｉ，ＬｉＧｕａｎｇｈｕｉ，ＹｅＧａｎｇ（ＲｅｓｅａｒｃｈＩｎｓｔｉｔｕｔｅｏｆＰｅｔｒｏｌｅｕｍＰｒｏｃｅｓｉｎｇ，Ｂｅｉｊｉｎｇ１０００８３...

Impact of nanoparticle shape on thermohydraulic performance of a nanofluid in an enhanced microchannel heat sink for utilization in cooling of electronic components

In this article,the thermal–hydraulic efficacy of a boehmite nanofluid with various particle shapes is evaluated inside a microchannel heat sink.The study is done for particle shapes of platelet,cylinder,blade,brick,and oblate spheroid at Reynolds numbers(Re)of 300,800,1300,and 1800.The particle volume fraction is assumed invariant for all of the nanoparticle shapes.The heat transfer coefficient(h),flow irregularities,pressure loss,and pumping power heighten by the elevation of the Re for all of the nanoparticle shapes.Also,the nanofluid having the platelet-shaped nanoparticles leads to the greatest h,and the nanofluid having the oblate spheroid particles has the lowest h and smallest pressure loss.In contrast,the nanofluid having the platelet-shaped nanoparticles leads to the highest pressure loss.The mean temperature of the bottom surface,thermal resistance,and temperature distribution uniformity decrease by the rise in the Reynolds number for all of the particle shapes.Also,the best distribution of the temperature and the lowest thermal resistance are observed for the suspension containing the platelet particles.Thereby,the thermal resistance of the nanofluid with the platelet particles shows a 9.5%decrement compared to that with the oblate spheroid particles at Re=300.For all the nanoparticle shapes,the figure of merit(FoM)uplifts by elevating the Re,while the nanofluids containing the brickand oblate spheroid-shaped nanoparticles demonstrate the highest FoM values.

Effects of Nano-Filler on the Thermal and Fire-Resistant Properties of Ethylene-Vinyl Acetate Copolymer

Sepiolite （S9, B10, B20, B40） and boehmite have been added to an intumecent flame retardant （IFR） system to produce the halogen-free and fire-resistant ethylene-vinyl acetate copolymer （EVM） rubber. The rubber contains ammonium polyphosphate （APP） as acid source, double pentaerythritol （D-PER） as carbon source and melamine （MN） as gas source. The effects of nano-filler sepiolite and boehmite on the fire-resistant property of EVM rubber based on IFR system were investigated. The test results show that the system with nano-filler of sepiolite B10 has the best fire-resistant property. The process of smoke emission and thermal decomposition, the element composition of char surface and the micro morphology of intumecent char layer of the EVM IFR system with nano-filler were also studied by NBS chamber, thermogravimetric （TG） analysis, X- ray photoelectron spectroscopy （XPS） and scanning electron microscope （SEM）.

STUDY ON PREPARATION OF SUPPORTED ALUMINA MEMBRANE USING SOL- GEL METHOD

A stable colloidal boehmite sol was made with the aluminium iso propoxide made in China and used to prepare the supported γ alumina membrane using sol gel method. The γ alumina thin layer was characterized by SEM, N 2 sorption method and permeation measurement. The γ alumina membrane was prepared with uniform surface, thickness of 3 μm and average diameter of about 5 nm. The permeabilities of the single gases of H 2, N 2, Ar and their separation factors were measured. The experimental data explained a behavior of Knudsen diffusion for the gas transport through the thin membrane.

Ultralong and Mesoporous ZnO and γ-Al_2O_3 Oriented Nanowires Obtained by Template-assisted Hydrothermal Approach

Highly mesoporous Zn O and g-Al2O3nanowires（NWs） are both synthesized by a hydrothermal method using commercially available porous anodic aluminium oxide（AAO） as template. AAO membrane acts as template for Zn O NWs and both as template and precursor for g-Al2O3 NWs. The formation of intermediate phases of porous Zn6Al2（OH）16CO3and boehmite（g-Al OOH） were observed, both occurring during the hydrothermal synthesis of porous Zn O and g-Al2O3 NWs, respectively, and disappearing after annealing at 600 C. This novel template-assisted hydrothermal process leads to the formation of porous Zn O and g-Al2O3NWs（specific surface area of 192 m2 g 1and 263 m2 g 1, respectively）, showing pore sizes around 4 nm in diameter. The influence of the reaction parameters on the nanostructure morphology was also investigated. A Zn O seed layer, deposited on the AAO channels prior to the hydrothermal synthesis, leads to more compact Zn O nanowires（99 m2 g-1） protecting the AAO host from the chemical attack of the precursor solution.

Effect of konjac glucomannan and chitosan-based film coatings on the quality of fresh sea bass(Lateolabrax maculatus)under refrigerated condition

Sea bass(Lateolabrax maculatus)is one of the important seafood in China.Its shelf-life under refrigerated storage exponentially deteriorate due to the growth of spoilage microorganisms,protein degradation and lipid oxidation.In this study,4 coating materials namely,konjac glucomannan-whey protein isolate(KGM-WPI)film,chitosan-sweet potato starch(CHI-SPS)film,chitosan-bamboo fungus(CHI-BF)film,and chitosan-boehmite alumina(CHI-BAH)have been explored to enhance the shelf life of sea bass during 8 days of refrigerated storage.Overall,CHI-BF was observed to be best in retaining hardness,gumminess and maintaining total volatile basic nitrogen value.Whereas CHI-SPS was found to retain chewiness and maintain lower values for drip loss and peroxide value.CHI-BAH coating was observed to maintain the lower values for pH and EC values of sea bass under refrigerated storage.However,the least increase in total viable count and minimum change in b^(*)value was observed in the case of sea bass coated with KGM-WPI.The current research fi ndings provide a new practical storage method for the entire fresh fish.The fresh fish can be coated with different coating materials and store on the ice at 4℃without packaging during retailing.These film coated whole fresh fish retains its microbial and sensory quality.