Na_(3)V_(2)(PO_(4))_(3)(NVP)cathode material of the sodium ion battery(1 C=117 mAh g-1)has a NASICON-type structure,which not only facilitates the rapid migration of sodium ions,but also has a small volume deformation...Na_(3)V_(2)(PO_(4))_(3)(NVP)cathode material of the sodium ion battery(1 C=117 mAh g-1)has a NASICON-type structure,which not only facilitates the rapid migration of sodium ions,but also has a small volume deformation during sodium ion de-intercalation and the main frame mechanism remains unchanged,and thus is seen as an energy storage material for a wide range of applications,but has a limited electronic conductivity due to its structure.In this paper,NVP cathode materials with finer primary particles are successfully prepared using a simple hydrothermal treatment-assisted sol-gel method.The increased pore size of the NVP materials prepared under the hydrothermal process allows for more active sites and more effective resistance to the volume deformation of sodium ions during insertion/extraction processes,effectively facilitating the diffusion of ions and electrons.The Na_(3)V_(2)(PO_(4))_(3) material obtained by the optimized process exhibited good crystallinity in XRD characterization,as well as superior electrochemical properties in a series of electrochemical tests.A specific capacitance of 106.3 mAh g^(-1) at 0.2 C is demonstrated,compared to 96.5 mAh g^(-1) for Na_(3)V_(2)(PO_(4))_(3) without hydrothermal treatment,and cycling performance is also improved with 93%capacity retention.The calculated sodium ion diffusion coefficient(DNa=5.68×10^(-14))obtained after EIS curve fitting of the improved sample illustrates that the pore structure is beneficial to the performance of the Na_(3)V_(2)(PO_(4))_(3)cathode material.展开更多
Li3V2-2/3xMnx（PO4）3（0≤x≤0.12） powders were synthesized by sol-gel method. The effect of Mn2＋-doping on the structure and electrochemical performances of Li3V2（PO4）3/C was characterized by XRD, SEM, XPS, galva...Li3V2-2/3xMnx（PO4）3（0≤x≤0.12） powders were synthesized by sol-gel method. The effect of Mn2＋-doping on the structure and electrochemical performances of Li3V2（PO4）3/C was characterized by XRD, SEM, XPS, galvanostatic charge /discharge and electrochemical impedance spectroscopy（EIS）. The XRD study shows that a small amount of Mn2＋-doped does not alter the structure of Li3V2（PO4）3/C materials, and all Mn2＋-doped samples are of pure single phase with a monoclinic structure （space group P21/n）. The XPS analysis indicates that valences state of V and Mn are ＋3 and ＋2 in Li3V1.94Mn0.09（PO4）3/C, respectively, and the citric acid in raw materials was decomposed into carbon during calcination, and residual carbon exists in Li3V1.94Mn0.09（PO4）/C. The results of electrochemical measurements show that Mn2＋-doping can improve the cyclic stability and rate performance of these cathode materials. The Li3V1.94Mn0.09（PO4）3/C cathode material shows the best cyclic stability and rate performance. For example, at the discharge current density of 40 mA/g, after 100 cycles, the discharge capacity of Li3V1.94Mn0.09（PO4）3/C declines from initial 158.8 mA·h/g to 120.5 mA·h/g with a capacity retention of 75.9%; however, that of the Mn-undoed sample declines from 164.2 mA·h/g to 72.6 mA·h/g with a capacity retention of 44.2%. When the discharge current is increased up to 1C, the intial discharge capacity of Li3V1.94Mn0.09（PO4）3/C still reaches 146.4 mA·h/g, and the discharge capacity maintains at 107.5 mA·h/g after 100 cycles. The EIS measurement indicates that Mn2＋-doping with a appropriate amount of Mn2＋ decreases the charge transfer resistance, which is favorable for the insertion/extraction of Li＋.展开更多
Ag3PO4 is found to be a highly efficient photocatalyst and receives great attention. The high activity of the photocatalyst is credited to the intrinsic electronic structure. The morphology control and nano-composite ...Ag3PO4 is found to be a highly efficient photocatalyst and receives great attention. The high activity of the photocatalyst is credited to the intrinsic electronic structure. The morphology control and nano-composite fabrication are used to improve the performance and practicability. This paper reviews the structure, properties and some theoretical aspects of Ag3PO4 single crystal. Also, the major strategies, namely the morphology control and hetero-nanostructure construction, as ways to improve the performance of Ag3PO4-based photocatalysts, are summarized with the aid of some typical instances.展开更多
2LiFe1-xCoxPO4-Li3V2（P04）3/C was synthesized using Fel-2xCo2xVO4 as precursor which was prepared by a simple co-precipitation method. 2LiFej-xCoxPO4-Li3V2（PO4）3/C samples were characterized by X-ray diffraction （...2LiFe1-xCoxPO4-Li3V2（P04）3/C was synthesized using Fel-2xCo2xVO4 as precursor which was prepared by a simple co-precipitation method. 2LiFej-xCoxPO4-Li3V2（PO4）3/C samples were characterized by X-ray diffraction （XRD）, scanning electron microscopy （SEM） and electrochemical measurements. All 2LiFel-xCoxPOa-Li3V2（PO4）3/C composites are of the similar crystal structure. The XRD analysis and SEM images show that 2LiFe0.96Co0.04PO4-Li3V2（PO4）3/C sample has the best-ordered structure and the smallest particle size. The charge-discharge tests demonstrate that these powders have the best electrochemical properties with an initial discharge capacity of 144.1 mA.h/g and capacity retention of 95.6% after 100 cycles when cycled at a current density of 0.1C between 2.5 and 4.5 V.展开更多
文摘Na_(3)V_(2)(PO_(4))_(3)(NVP)cathode material of the sodium ion battery(1 C=117 mAh g-1)has a NASICON-type structure,which not only facilitates the rapid migration of sodium ions,but also has a small volume deformation during sodium ion de-intercalation and the main frame mechanism remains unchanged,and thus is seen as an energy storage material for a wide range of applications,but has a limited electronic conductivity due to its structure.In this paper,NVP cathode materials with finer primary particles are successfully prepared using a simple hydrothermal treatment-assisted sol-gel method.The increased pore size of the NVP materials prepared under the hydrothermal process allows for more active sites and more effective resistance to the volume deformation of sodium ions during insertion/extraction processes,effectively facilitating the diffusion of ions and electrons.The Na_(3)V_(2)(PO_(4))_(3) material obtained by the optimized process exhibited good crystallinity in XRD characterization,as well as superior electrochemical properties in a series of electrochemical tests.A specific capacitance of 106.3 mAh g^(-1) at 0.2 C is demonstrated,compared to 96.5 mAh g^(-1) for Na_(3)V_(2)(PO_(4))_(3) without hydrothermal treatment,and cycling performance is also improved with 93%capacity retention.The calculated sodium ion diffusion coefficient(DNa=5.68×10^(-14))obtained after EIS curve fitting of the improved sample illustrates that the pore structure is beneficial to the performance of the Na_(3)V_(2)(PO_(4))_(3)cathode material.
基金Project (20771100) supported by the National Natural Science Foundation of China
文摘Li3V2-2/3xMnx（PO4）3（0≤x≤0.12） powders were synthesized by sol-gel method. The effect of Mn2＋-doping on the structure and electrochemical performances of Li3V2（PO4）3/C was characterized by XRD, SEM, XPS, galvanostatic charge /discharge and electrochemical impedance spectroscopy（EIS）. The XRD study shows that a small amount of Mn2＋-doped does not alter the structure of Li3V2（PO4）3/C materials, and all Mn2＋-doped samples are of pure single phase with a monoclinic structure （space group P21/n）. The XPS analysis indicates that valences state of V and Mn are ＋3 and ＋2 in Li3V1.94Mn0.09（PO4）3/C, respectively, and the citric acid in raw materials was decomposed into carbon during calcination, and residual carbon exists in Li3V1.94Mn0.09（PO4）/C. The results of electrochemical measurements show that Mn2＋-doping can improve the cyclic stability and rate performance of these cathode materials. The Li3V1.94Mn0.09（PO4）3/C cathode material shows the best cyclic stability and rate performance. For example, at the discharge current density of 40 mA/g, after 100 cycles, the discharge capacity of Li3V1.94Mn0.09（PO4）3/C declines from initial 158.8 mA·h/g to 120.5 mA·h/g with a capacity retention of 75.9%; however, that of the Mn-undoed sample declines from 164.2 mA·h/g to 72.6 mA·h/g with a capacity retention of 44.2%. When the discharge current is increased up to 1C, the intial discharge capacity of Li3V1.94Mn0.09（PO4）3/C still reaches 146.4 mA·h/g, and the discharge capacity maintains at 107.5 mA·h/g after 100 cycles. The EIS measurement indicates that Mn2＋-doping with a appropriate amount of Mn2＋ decreases the charge transfer resistance, which is favorable for the insertion/extraction of Li＋.
文摘Ag3PO4 is found to be a highly efficient photocatalyst and receives great attention. The high activity of the photocatalyst is credited to the intrinsic electronic structure. The morphology control and nano-composite fabrication are used to improve the performance and practicability. This paper reviews the structure, properties and some theoretical aspects of Ag3PO4 single crystal. Also, the major strategies, namely the morphology control and hetero-nanostructure construction, as ways to improve the performance of Ag3PO4-based photocatalysts, are summarized with the aid of some typical instances.
基金Project(51072233) supported by National Natural Science Foundation of China
文摘2LiFe1-xCoxPO4-Li3V2（P04）3/C was synthesized using Fel-2xCo2xVO4 as precursor which was prepared by a simple co-precipitation method. 2LiFej-xCoxPO4-Li3V2（PO4）3/C samples were characterized by X-ray diffraction （XRD）, scanning electron microscopy （SEM） and electrochemical measurements. All 2LiFel-xCoxPOa-Li3V2（PO4）3/C composites are of the similar crystal structure. The XRD analysis and SEM images show that 2LiFe0.96Co0.04PO4-Li3V2（PO4）3/C sample has the best-ordered structure and the smallest particle size. The charge-discharge tests demonstrate that these powders have the best electrochemical properties with an initial discharge capacity of 144.1 mA.h/g and capacity retention of 95.6% after 100 cycles when cycled at a current density of 0.1C between 2.5 and 4.5 V.
