Bi26MO10O69 nanopowder was prepared by hydrothermal method and used as a surface modification material for oxygen separation membrane to enhance oxygen permeability. Thermal decomposition behavior and phase variation ...Bi26MO10O69 nanopowder was prepared by hydrothermal method and used as a surface modification material for oxygen separation membrane to enhance oxygen permeability. Thermal decomposition behavior and phase variation of the precursor were investigated by thermal analyzer （TG-DSC） and high-temperature X-ray diffraction （HT-XRD）. Bi26MO10O69 porous layer was coated on the air side of BaCo0.7Fe0.2Nb0.1O3-δ （BCFN） oxygen permeable membrane by dipping method. In the partial oxidation experiment of coke oven gas （COG）, the Bi26Mo10O69-coated BCFN membrane exhibits higher oxygen permeability and CH4 conversion than the uncoated BCFN membrane. When the thickness of BCFN membrane was 1 mm and the COG and air fluxes were 120 and 100 mL/min, the oxygen permeation flux reached 16.48 mL/（min.cm^2） at 875℃, which was 16.96% higher than the uncoated BCFN membrane. Therefore, Bi26MoloO69 porous layer on the air side will be promising modification coating on the oxygen permeability of BCFN membrane.展开更多
Fluidized bed reactor is widely used in coal char-CO2 gasification. In this work, the production of syngas by using a fluidized bed gasification technique was first investigated and then the effect of the produced syn...Fluidized bed reactor is widely used in coal char-CO2 gasification. In this work, the production of syngas by using a fluidized bed gasification technique was first investigated and then the effect of the produced syngas on the performance of the solid oxide fuel cell with a configuration of La0.4Sr0.6Co0.2 Fe0.7 Nb0.1O3-δ//La0.8Sr0.2Ga0.83Mg0.17O3-δ//La0.4Sr0.6Co0.2Fe0.7Nb0.1O3-δ（LSCFN//LSGM//LSCFN） was studied. During the syngas production, we found that the volume fraction of CO increased with the increment of gasification temperature, and it reached a maximum value of 88.8%, corresponding to a composition of 0.76% H2, 88.8% CO, and 10.44% CO2, when the ratio of oxygen mass flow rate to that of coal char （Mo2/Mchar） increased to 0.29. In the following utilization of the produced syngas in solid oxide fuel cells, it was found that the increasing CO volume fraction in the syngas results in a gradual increase of the peak power density of the LSCFN//LSGM//LSCFN cell. The maximum peak power density of 410 mW/cm^2 was achieved for the syngas produced at 0.29 of Mo2/Mchar. In the stability test, the cell voltage decreased by 4% at a constant current density of 0.475 A/cm^2 after 54 h when fueled with the syngas with the composition of 0.76% H2, 88.8% CO, and 10.44% CO2. It reveals that a carbon deposition with the content of 13.66% in the anode is attributed to the cell performance degradation.展开更多
选择具有双钙钛矿结构的Sr2Fe Nb O6(SFN)及La0.9Sr0.1Ga0.8Mg0.2O3-δ(LSGM)材料混合作为固体氧化物电解池(SOEC)的阴极,在SFN-LSGM中掺杂不同比例的淀粉,经过干压成型并在1400℃下烧结后得到测试样。利用真实密度仪及阿基米德法测定...选择具有双钙钛矿结构的Sr2Fe Nb O6(SFN)及La0.9Sr0.1Ga0.8Mg0.2O3-δ(LSGM)材料混合作为固体氧化物电解池(SOEC)的阴极,在SFN-LSGM中掺杂不同比例的淀粉,经过干压成型并在1400℃下烧结后得到测试样。利用真实密度仪及阿基米德法测定了样品的孔隙率;利用热分析仪测定了不同孔隙率的样品在35~1400℃条件下的热膨胀系数,研究该材料与常用SOEC电解质材料La0.9Sr0.1Ga0.8Mg0.2O3-δ(LSGM)的热匹配性能;之后利用电化学工作站测试了该材料在纯氢气气氛下电导率与孔隙率的关系。结果表明,样品孔隙率与淀粉掺杂量成正比,孔隙率对该材料热膨胀系数影响不大,且该材料与LSGM电解池热匹配性能良好。另外,当样品孔隙率增加时,该材料在850℃纯氢气气氛下的电导率在18%孔隙率时达到最大值。展开更多
基金Projects(51272154,51472156)supported by the National Natural Science Foundation of ChinaProjects(sdcx2012033,sdcx2012062)supported by the Innovation Fund of Shanghai University,China+1 种基金Project(14ZR1416400)supported by Special Research Foundation for Training and Selecting Outstanding Young Teachers of Universities in Shanghai,Chinasupported by Shanghai Science and Technology Committee,China
文摘Bi26MO10O69 nanopowder was prepared by hydrothermal method and used as a surface modification material for oxygen separation membrane to enhance oxygen permeability. Thermal decomposition behavior and phase variation of the precursor were investigated by thermal analyzer （TG-DSC） and high-temperature X-ray diffraction （HT-XRD）. Bi26MO10O69 porous layer was coated on the air side of BaCo0.7Fe0.2Nb0.1O3-δ （BCFN） oxygen permeable membrane by dipping method. In the partial oxidation experiment of coke oven gas （COG）, the Bi26Mo10O69-coated BCFN membrane exhibits higher oxygen permeability and CH4 conversion than the uncoated BCFN membrane. When the thickness of BCFN membrane was 1 mm and the COG and air fluxes were 120 and 100 mL/min, the oxygen permeation flux reached 16.48 mL/（min.cm^2） at 875℃, which was 16.96% higher than the uncoated BCFN membrane. Therefore, Bi26MoloO69 porous layer on the air side will be promising modification coating on the oxygen permeability of BCFN membrane.
基金financially supported by the National Basic Research Program of China (Grant Nos. 2012CB215404, 2012CB215406)State Key Laboratory of Power Systems in Tsinghua University (No. SKLD15Z02, Fuel Cell Distributed Power Generation System)One-hundred Leading Talents Development Project for Progress on Science and Technology of Beijing (No. 041504130)
文摘Fluidized bed reactor is widely used in coal char-CO2 gasification. In this work, the production of syngas by using a fluidized bed gasification technique was first investigated and then the effect of the produced syngas on the performance of the solid oxide fuel cell with a configuration of La0.4Sr0.6Co0.2 Fe0.7 Nb0.1O3-δ//La0.8Sr0.2Ga0.83Mg0.17O3-δ//La0.4Sr0.6Co0.2Fe0.7Nb0.1O3-δ（LSCFN//LSGM//LSCFN） was studied. During the syngas production, we found that the volume fraction of CO increased with the increment of gasification temperature, and it reached a maximum value of 88.8%, corresponding to a composition of 0.76% H2, 88.8% CO, and 10.44% CO2, when the ratio of oxygen mass flow rate to that of coal char （Mo2/Mchar） increased to 0.29. In the following utilization of the produced syngas in solid oxide fuel cells, it was found that the increasing CO volume fraction in the syngas results in a gradual increase of the peak power density of the LSCFN//LSGM//LSCFN cell. The maximum peak power density of 410 mW/cm^2 was achieved for the syngas produced at 0.29 of Mo2/Mchar. In the stability test, the cell voltage decreased by 4% at a constant current density of 0.475 A/cm^2 after 54 h when fueled with the syngas with the composition of 0.76% H2, 88.8% CO, and 10.44% CO2. It reveals that a carbon deposition with the content of 13.66% in the anode is attributed to the cell performance degradation.
文摘选择具有双钙钛矿结构的Sr2Fe Nb O6(SFN)及La0.9Sr0.1Ga0.8Mg0.2O3-δ(LSGM)材料混合作为固体氧化物电解池(SOEC)的阴极,在SFN-LSGM中掺杂不同比例的淀粉,经过干压成型并在1400℃下烧结后得到测试样。利用真实密度仪及阿基米德法测定了样品的孔隙率;利用热分析仪测定了不同孔隙率的样品在35~1400℃条件下的热膨胀系数,研究该材料与常用SOEC电解质材料La0.9Sr0.1Ga0.8Mg0.2O3-δ(LSGM)的热匹配性能;之后利用电化学工作站测试了该材料在纯氢气气氛下电导率与孔隙率的关系。结果表明,样品孔隙率与淀粉掺杂量成正比,孔隙率对该材料热膨胀系数影响不大,且该材料与LSGM电解池热匹配性能良好。另外,当样品孔隙率增加时,该材料在850℃纯氢气气氛下的电导率在18%孔隙率时达到最大值。
