Effect of Chromium on CCT Diagrams of Novel Air-Cooled Bainite Steels Analyzed by Neural Network

The quantitative effects of chromium content on continuous cooling transformation （CCT） diagrams of novel air-cooled bainite steels were analyzed using artificial neural network models. The results showed that the chromium may retard the high and medium-temperature martensite transformation.

Quantitative analysis of Ni effect on CCT diagrams of novel air-cooled bainite steels using artificial neural network models

The quantitative effect of Ni content on continuous cooling transformation （CCT） diagrams of novel air-cooled bainite steels was analyzed using artificial neural network models. The results showed that Ni may retard the high- and medium-temperature transformation and martensite transformation. The results conform to the materials science theories.

Effect of zirconium addition on the austenite grain coarsening behavior and mechanical properties of 900 MPa low carbon bainite steel

The ultra-fine bainitic microstructure of a 900 MPa low carbon bainitic Cu-Ni-Mo-B steel was obtained by a newly developed relaxation precipitation control （RPC） phase transformation processing. In a pan-cake like prior-austenite grain, the micro- structure consisted of lath bainite, a little of abnormal granular bainite, and acicular ferrite. The effect of zirconium carbonitrides on the austenite grain coarsening behavior was studied by transmission electron microscopy （TEM）. The results show that, the lath is narrower with increasing cooling rate. The ratio of all kinds of bainitic microstructure is proper with the intermediate cooling rate; and Zr-containing precipitates distribute uniformly, which restrains austenite grain growing in heat-affected welding zone.

Heterogeneous Nuclei of Intergrowth Eutectic in Austenite-Bainite Steel Modified by Ce and Al

The nodular eutectic in the austenite bainite steel is pseudo eutectic of austenite and (Fe,Mn) 3C, which is formed between austenite dendrites at the end of the solidification because of the segregation of C and Mn. By thermodynamics calculation, two dimensional lattice misfitting calculation and observations of transmission electron microscope(TEM) and scanning electron microscope(SEM), it is shown that CeO 2 and CeAlO 3 may act as the heterogeneous nuclei of the nodular eutectic.

In situ measured growth rates of bainite plates in an Fe-C-Mn-Si superbainitic steel

The growth rates of bainite plates in an Fe-C-Mn-Si superbainitie steel were investigated by in situ observation. The lengthening rates of ferrite bainite during both cooling and isothermal holding processes were observed and the growth rates of bainite plates nucleating at grain boundaries, within grains and on preformed bainite were measured. It is indicated that the lengthening rates of bainite plates during the cooling and isothermal processes were different, and that the growth rates of bainite plates nucleating at different types of sites also demon- strated diversity. The bainite plates initiating at [vain boundaries during cooling grew the fastest, while the plates nucleating on preformed bainite did the slowest. However, the growth rate of the bainite plates nucleating at grain boundaries during isothermal transformation de- creased the most, whereas the bainite plates initiating within grains grew the fastest. In addition, the growth rate of ferrite bainite in the study supported the diffusion transformation mechanism of bainite from the viewooint of ~rowth rate.

Refinement of packet size in low carbon bainitic steel by special thermo-mechanical control process

The packet size of bainitic steel can be refined by a specialrelaxation-precipitation-control phase transformation (RFC) technology. When processed by RPCprocess, the low carbon bainitic steel composes of two kinds of main intermediate transformationphases. One is ultra-fine lath-like bainitic ferrite and the lath is less than 1μm in width andabout 6 μm in length; the alignment of laths forms a refined packet, and the size of packets isabout 5-7 μm in length and about 3-4μm in width. The other is acicular structure. The morphologyand distribution of these acicular structures are influenced by relaxation process, the thin andshort acicular structures cut the prior austenite grain and refine the bainitic packet size. For theoptimum relaxation time, the packet size can be refined to the finest. The mechanical propertiesare influenced by relaxation time and the 800 MPa grade low carbon bainitic steel with excellenttoughness can be obtained by RPC process.

In situ observations of austenite grain growth in Fe-C-Mn-Si super bainitic steel

In situ observations of austenite grain growth in Fe-C-Mn-Si super bainitic steel were conducted on a high-temperature laser scanning confocal microscope during continuous heating and subsequent isothermal holding at 850, 1000, and 1100℃ for 30 min. A grain growth model was proposed based on experimental results. It is indicated that the austenite grain size increases with austenitizing temperature and holding time. When the austenitizing temperature is above 1100℃, the austenite grains grow rapidly, and abnormal austenite grains occur. In addition, the effect of heating rate on austenite grain growth was investigated, and the relation between austenite grains and bainite morphology after bainitic transformations was also discussed.

Recent Development of Air-Cooled Bainitic Steels Containing Manganese

The superiorities of air-cooled bainitic steels were described. A series of air-cooled bainitic steels containing manganese were developed and presented, which include low carbon granular bainitic steels, low carbon grain-boundary allotriomorphic ferrite/granular bainite dual phase steels, medium and medium high carbon bainite/martensite dual phase steel, low carbon carbide free bainite/martensite dual phase steels and casting bainitic steels. The development of ultra-low carbon bainitic steels in China was also introduced.

Structure Character of M-A Constituent in CGHAZ of New Ultra-Low Carbon Bainitic Steel under Laser Welding Conditions

800 MPa grade new ultra-low carbon bainitic （NULCB） steel is the recently developed new generation steel. The microstructure in the coarse-grained heat affected zone （CGHAZ） of NULCB steel under laser welding conditions was investigated by thermal simulation. The influence of the cooling time from 800℃ to 500℃.t8/5 （0.3-30 s）, on the microstructure of the CGHAZ was discussed. The experimental results indicate that the microstructnre of the CGHAZ is only the granular bainite which consists of bainitic ferrite （BF） lath and M-A constituent while t8/5 is 0.3-30 s. The M-A constituent consists of twinned martensite and residual austenite, and the change of the volume fraction of the residual austenite in the M-A constituent is very small when t8/5 is between 0.3 and 30 s. The morphology of the M-A constituent obviously changes with the variation of t8/5.As t8/5 increases, tile average width, gross and shape parameter of the M-A constituent increase, while the line density of the M-A constituent decreases.

Complex Precipitation Mechanism of Ti-Nb-V Microalloyed Bainitic Base High Strength Steel

The addition of high Ti（>0.1%） in microalloyed bainitic high strength steel was designed, and the precipitation morphology of steels with different Ti, Nb, and V contents was studied by utilizing transmission electron microscopy（TEM）. Based on the classical nucleation-crystal growth theory and the Johnson-Mehl-Avrami equation, the precipitation thermodynamic and kinetic model of second phase particles in austenite was established in the form of（Nbx,Vy,Tiz）C, and the complex precipitation mechanism of second phase particles was emphatically studied. The experimental results show that the complex precipitation particles could be divided into two categories: the coarser particles with about 100 nm grain size and the independent complex precipitation particles in the form of（Nb,V,Ti）C with 35-50 nm grain size. The latter has a better precipitation strengthening effect, and the calculated PTT curve shows a typical "C" shape. When the deformed storage energy is 3 820 J?mol-1, the fastest precipitation temperature of calculated PTT curve is 925 °C, and the calculated result is essentially consistent with experimental values. The increase of Ti content increased the nose point temperature and expanded the range of fastest precipitation temperature.

Effects of Mn on Microstructures and Properties of Hot Rolled Low Carbon Bainitic Steels

Two kinds of Mn-Si-Mo low carbon steels were designed to study the effects of Mn on the microstructures and properties of hot rolled low carbon bainitic steels.To reduce the production cost,a very low Mo content of 0.13%was added in both steels.After hot rolling,the mechanical properties of samples were tested.Microstructure was observed and analyzed by optical microscope and transmission electron microscope.The results show that the strength of tested steels increases with the increase in Mn content,while the elongation decreases.When Mn content increases,the bainite microstructure increases.The results can provide a theoretical basis for composition design and industrial production of low cost low carbon bainitic steels.

Impact Toughness Scattering of Bainitic Steel in the Ductile-brittle Transition Temperature Region

The impact toughness scattering in the ductile-brittle transition temperature （DBTT） region was experimentally examined on mixed and homogeneous grains of low alloy high strength bainitic steel under dynamic loading conditions. The results revealed that the mixed grain microstructure had larger impact toughness scattering than the homogeneous one, and the impact toughness scattering was mainly caused by the scattering in the cleavage fractttre stress σf. The value of σf. is related to the size of the microcrack formed in the bainitic packet. When a bainitic packet-sized microcrack propagates from one bainitic packet into the adjacent packet, cleavage fracture occurs. The cleavage fracture is controlled by the few coarse packets in the microstructures, and the σf scattering is influenced by the varied distances/relative locations between these coarse packets, and homogenizing the distribution of fine bainitic packet sizes is an effective way to reduce the impact toughness scattering in the DBTT region.

Influence of Creep Strength of Weld on Interfacial Creep Damage of Dissimilar Welded Joint between Martensitic and Bainitic Heat-Resistant Steel

The mechanical properties, creep rupture strength, creep damage and failure characteristics of dissimilar metal welded joint （DMWJ） between martensitic （SA213T91） and bainitic heat-resistant steel （12Cr2MoWVTiB（G102）） have been investigated by means of pulsed argon arc welding, high temperature accelerated simulation, mechanical and creep rupture test, and scanning electronic microscope （SEM）. The results show that there is a marked drop of mechanical properties of undermatching joint, and low ductility cracking along weld/G102 interface is induced due to creep damage. Creep rupture strength of overmatching joint is the least. The mechanical properties of medium matching joint are superior to those of overmatching and undermatching joint, and creep damage and failure tendency along the interface of weld/G102 are lower than those of overmatching and undermatching joint after accelerated simulation for 500 h, 1 000 h, 1 500 h, and the creep rupture strength of medium matching joint is the same as that of undermatching joint. Therefore, it is reasonable that the medium matching material is used for dissimilar welded joint between martensitic and bainitic steel.

Welding of SA213-T91 and SA213-T23 heat-resistant steels applied in ultra supercritical thermal power units

The marteasite SA213-191 and bainite SA213-T23 high-temperature resistant steels were applied to the heating surface of the ultra supercritical thermal power unit boiler. The weld metal microstructures and welded joint performance between the two kinds of dissimilar steels were analyzed. The main reasons of the welding defects such as hot crack, cold crack, brittleness and decrease in toughness were discussed during the welding of the dissimilar heat-resistant steels of SA213- 191 and SA213-T23 in boiler manufacturing and processing operation. The welding materials were chosen and welding procedure was made according to the base metals.

Ratcheting led surface failure of medium carbon bainitic steel under mild operation conditions

The behavior of rolling contact fatigue (RCF) of medium carbon bainitic back-up roll steel was investigated under its actual work conditions. A kind of asperity-scale surface originated cracks, which is lying parallel or at an acute angle to the surfaces, initiated after unidirectional plastic flow of the material in thin surface layer had occurred. Theoretical analysis indicates that they nucleate due to plastic ratcheting induced by asperity contact stresses, and consequently are named as ratcheting cracks. After nucleating and initially propagating, they arrest at some depth and resume propagating till about 70%-80% of the RCF failure life by initially turning parallel to contact surfaces. Their behavior of initiation and propagation is confined to a thin layer prior to the formation of surface distress. According to the critical principle of the preventive grinding strategy, removing the asperity influenced surface layer at about 70%-80% of the RCF failure life can effectively prevent the ratcheting cracks from developing into surface distress, which can lead to the formation of macro-RCF failure soon.

Evaluation of factors affecting the edge formability of two hot rolled multiphase steels

In this study, the effect of various factors on the hole expansion ratio and hence on the edge formability of two hot rolled multiphase steels, one with a ferrite–martensite microstructure and the other with a ferrite-bainite microstructure, was investigated through systematic microstructural and mechanical characterization. The study revealed that the microstructure of the steels, which determines their strain hardening capacity and fracture resistance, is the principal factor controlling edge formability. The influence of other factors such as tensile strength, ductility, anisotropy, and thickness, though present, are secondary. A critical evaluation of the available empirical models for hole expansion ratio prediction is also presented.

CCT-DIAGRAMS OF Si-Mn-Mo BAINITIC STEELS

CCT-diagrams of Si-Mn-Mo bainitic steels have been determined.With Mo 0.25%,the high-temperature transformation of the steel shifts large to the right,and the bainitic trans- formation region becomes a“flat topped C-curve”at cooling rate in wide range.Si in the steel may cause shift of the bainitic transformation region towards the right,and of the pro-eutectoid ferritic transformation region towards the left.Mn may delay the high temper- ature transformation more violently than the bainitic transformation.

Study on laser welded heat-affected zone in new ultralow carbon bainitic steel

800 MPa grade ultralow carbon bainitic （NULCB） steel is the recently developed new generation steel, which was produced by thermo mechanical controlled processing ＆ relaxation-precipitation controlling transformation （TMCP＆RPC） tech- nique. The microstructure and the mechanical properties of the heat-affected zone （HAZ） in NULCB steel under laser welding conditions were investigated by using a Gleeble-1500 thermal simulator. The experimental results indicate that the simplex microstructure in the HAZ is granular bainite that consists of bainite-ferrite （BF） lath and M-A constituent when the cooling time from 800 to 500℃ （t8/5） is 0.3-30 s, and the M-A constituent consists of twinned martensite and residual austenite. As t8/5 increases, the hardness and tensile strength of HAZ decreases, but they are higher than that of the base metal, indicating the absence of softened zone after laser welding. The impact toughness of HAZ increases at first and then decreases when t8/5 increases. The impact energy of HAZ is much higher than that of the base metal when t8/5 is between 3 and 15 s. It indicates that excellent low temperature toughness can be obtained under appropriate laser welding conditions.

Research on microstructural evolution and dynamic recrystailization behavior of JB800 bainitic steel by FEM

Single pass compression tests were conducted on Gleeblel500 thermal simulator. The effect of different deformation parameters on the grain size of dynamically recrystallized austenite was analyzed. A mathematical model of dynamic recrystallization and a material database of JB800 steel, whose tensile strength is above 800 MPa, were set up. A subprogram was compiled using Fortran language and called by Marc finite element software. A thermal coupled elastoplastic finite element model was established to simulate the compression process. The grain size of recrystallized austenite obtained by different recrystallization models was simulated. The results show that the optimized dynamic recrystallization model of JB800 bainitic steel has a higher precision and yields good agreement with metallographic observations.

Mechanical Method Determining Precipitation in an Ultra-Low Carbon Bainitic Steel

Stress relaxation was chosen as the best method for monitoring the precipitation process. Tests were carried out on an ultra-low carbon bainitic steel containing Mn, Nb and B over 800~950℃. Specimens were solu- tion treated at 1250℃ for a certain holding period. A prestain of 20% was applied at a strain rate of 0.1/s. The exper- imental results are displayed by a set of stress vs. 1g(time) curves different from the typical stress relaxation curves. There are two singularities forming a stress plateau on the stress vs.1g(time) curves when precipitates could be observed. Suppose the first one is the start of precipitation (Ps), and the second represcnts the fihish (Pf). As a result Precipitation-Time-Temperature relationship is described as C-shape curves based on two points. This mechanical method is suitable and precise for measuring precipitates in microalloyed steels during hot working.