In this paper,a 5G wideband power amplifier(PA)with bandpass filtering response is synthesized using a bandwidth-extended bandpass filter as the matching network(MN).In this structure,the bandwidth(θ_(C))is defined a...In this paper,a 5G wideband power amplifier(PA)with bandpass filtering response is synthesized using a bandwidth-extended bandpass filter as the matching network(MN).In this structure,the bandwidth(θ_(C))is defined as a variable in the closedform equations provided by the microstrip bandpass filter.It can be extended over a wide range only by changing the characteristic impedances of the structure.Different from the other wideband MNs,the extension of bandwidth does not increase the complexity of the structure(order n is fixed).In addition,based on the bandwidth-extended structure,the wideband design of bandpass filtering PA is not limited to the fixed bandwidth of the specific filter structure.The theoretical analysis of the MN and the design flow of the PA are provided in this design.The fabricated bandpass filtering PA can support almost one-octave bandwidth(2-3.8 GHz),covering the two 5G bands(n41 and n78).The drain efficiency of 47%-60%and output power higher than 40 dBm are measured.Good frequency selectivity in S-parameter measurements can be observed.展开更多
A class of new planar dual-mode filters without coupling gaps is proposed. The proposed structures use a single patch wiuhout coupling gaps. Attenuation poles can be implemented on either side of the passband by chang...A class of new planar dual-mode filters without coupling gaps is proposed. The proposed structures use a single patch wiuhout coupling gaps. Attenuation poles can be implemented on either side of the passband by changing the locations of two feed lines. By cutting two corners in the patch, two attenuation poles on both sides of passband are implemented. A novel dual-mode elliptic-function bandpass filter structure without coupling gaps is also proposed. These new filters can provide a low insertion loss and reduce uncertainty in fabrication owing to the absence of coupling gaps.展开更多
This paper reviews the state-of-the-art filter designs for 60 GHz applications. The most promising filter solutions at this frequency include fiher-in-package where the filter itself is design in the packaging platfor...This paper reviews the state-of-the-art filter designs for 60 GHz applications. The most promising filter solutions at this frequency include fiher-in-package where the filter itself is design in the packaging platform and filter-on-chip which is an on-chip filter co-design for miniaturized system size with low packaging cost. Design methodology, design technology, key performance parameters, similarities and dift)rences, advantages and drawbacks, and future trends are explored and studied. Filters in the printed circuit board (PCB), low temperature co-fired ceramics (LTCC), organie material, and bipolar complementary metal oxide semicomtuctor (BiCMOS) chips are summarized and compared in details. Future design trends and challenges are also given after the review.展开更多
We report the design of a novel multiband metamaterial bandpass filter (BPF) in the terahertz (THz)-wave region. The designed BPF is composed of a metal-dielectric-metal sandwiched structure with three nested ring...We report the design of a novel multiband metamaterial bandpass filter (BPF) in the terahertz (THz)-wave region. The designed BPF is composed of a metal-dielectric-metal sandwiched structure with three nested rings on the top surface and a cross structure on the bottom surface. Full-wave simulation results show that the designed BPF has three transmission peaks at frequencies of 0.42, 1.27, and 1.86 THz with transmission rates of-0.87,-1.85, and-1.83 dB, respectively. Multi-reflection interference theory is introduced to explain the transmission mechanism of the designed triple-band BPF. The theoretical transmission spectrum is in good agreement with the full-wave simulated results. The designed BPF can maintain a stable performance as the incident angle varies from 0 to 30 for both transverse electric and transverse magnetic polarizations of the incident wave. The designed BPF can be potentially used in THz devices due to its multiband transmissions, polarization insensitivity, and stable wide-angle response in the THz region.展开更多
We investigate the guiding modes of spoof surface plasmon polaritons (SPPs) on a symmetric ultra-thin plasmonic structure. From the analysis, we deduce the operating frequency region of the single-mode propagation. ...We investigate the guiding modes of spoof surface plasmon polaritons (SPPs) on a symmetric ultra-thin plasmonic structure. From the analysis, we deduce the operating frequency region of the single-mode propagation. Based on this property, a spoof SPPs lowpass filter is then constituted in the microwave frequency. By introducing a transmission zero at the lower frequency band using a pair of stepped-impedance stubs, a wide passband filter is further realized. The proposed filter is fed by.a transducer composed of a microstrip line with a flaring ground. The simulated results show that the presented filter has an extremely wide upper stopband in addition to excellent passband filtering characteristics such as low loss, wide band, and high square ratio. A prototype passband filter is also fabricated to validate the predicted performances. The proposed spoof-SPPs filter is believed to be very promising for other surface waveguide components in microwave and terahertz bands.展开更多
This study is concerned with the diagnosis of discrepancies in a steel truss bridge by identifying dynamic properties from the vibration response signals of the bridges.The vibration response signals collected at brid...This study is concerned with the diagnosis of discrepancies in a steel truss bridge by identifying dynamic properties from the vibration response signals of the bridges.The vibration response signals collected at bridges under three different vehicular speeds of 10 km/hr,20 km/hr,and 30 km/hr are analyzed using statistical features such as kurtosis,magnitude of peak-to-peak,root mean square,crest factor as well as impulse factor in time domain,and Stockwell transform in the time-frequency domain.The considered statistical features except for kurtosis show uncertain behavior.The Stockwell transform showed low-resolution outcomes when the presence of noise in the recorded vibration responses.The elimination of noise and extraction of meaningful dynamic properties from the vibration responses is done by applying a new method which comes from the fusion of Hilbert transform with Spectral kurtosis and bandpass filtering.The outcomes obtained from Hilbert transform processed residual signals which are further filtered using bandpass filter show more robustness and accuracy in characterizing bridge modal frequencies from the noisy vibration responses.The proposed method produces a high-resolution frequency response which can unveil the joint discrepancy in the bridge structure.展开更多
In this study, we propose a novel resonator that is composed of a modified spiral with an embedded interdigital capacitor. A large ratio of the first spurious frequency to the fundamental resonant frequency is obtaine...In this study, we propose a novel resonator that is composed of a modified spiral with an embedded interdigital capacitor. A large ratio of the first spurious frequency to the fundamental resonant frequency is obtained, which is suitable for the design of filters with wide stopbands, and the circuit size is considerably reduced by embedding the interdigital structure in the spiral. For demonstration, a compact four-pole high temperature superconducting(HTS) filter with a center frequency of 568 MHz is designed and fabricated on double-sided YBCO film with a size of 11.4 mm×8.0 mm. The filter measurement shows excellent performance with an out-of-band rejection level better than 60.9 dB up to 3863 MHz.展开更多
A novel bandpass filter(BPF)based on spoof surface plasmon polaritons(SSPPs)using a compact folded slotline structure is proposed and experimentally demonstrated.The proposed novel SSPPs structure compared with a conv...A novel bandpass filter(BPF)based on spoof surface plasmon polaritons(SSPPs)using a compact folded slotline structure is proposed and experimentally demonstrated.The proposed novel SSPPs structure compared with a conventional plasmonic waveguide with slot line SSPPs unit structure at the same size,the considerable advantages in much lower asymptotic frequency with tight field confinement,which enable the proposed filter to be more miniaturization.A high-efficient mode conversion structure is designed to transition from TE-mode to SSPPs-mode by gradient slotline lengths.The low-frequency stop-band can be committed with microstrip to slotline evolution on both sides of the dielectric,while the high-frequency cutoff band is realized by the proposed SSPPs structure.The influence of dispersion relation,electric field distribution,surface current,and structural parameters on the transmission characteristics of the proposed BPF are analyzed by finite difference time domain(FDTD).To validate the design concept,the prototype of the miniaturized SSPPs BPF has been manufactured and measured.The experimental results show high performance of the fabricated sample,in which the working in a range of 0.9 GHz-5.2 GHz with the relative bandwidth is 142%,the insertion loss less than 0.5 dB,the reflection coefficient less than-10 dB,and the group delay is less than one ns.This works provides a mirror for realizing the miniaturization of waveguides,and the application and development of high-confinement SSPPs functional devices in the microwave and THz regimes.展开更多
An ultra-wideband bandpass filter(BPF)with a wide out-of-band rejection based on a surface plasmonic waveguide(SPW)slotline with ring grooves is designed and analyzed.A paired microstrip-to-slotline transition is desi...An ultra-wideband bandpass filter(BPF)with a wide out-of-band rejection based on a surface plasmonic waveguide(SPW)slotline with ring grooves is designed and analyzed.A paired microstrip-to-slotline transition is designed for quasiTEM to TM mode conversion by using a microstrip line with a circular pad and the slotline with the same circular slot.The mode conversion between the TM and the surface plasmon polariton(SPP)mode is realized by using a gradient slotline with ring grooves and an impedance matching technique.The upper cut-off frequencies of the passband can be adjusted by using these proposed SPP units,while the lower frequencies of the passband are created by using the microstrip-toslotline transitions to give an ultra-wideband BPF.The dispersion curves of SPP units,electric field distribution,and the transmission spectra of the proposed ultra-wideband bandpass filter are all calculated and analyzed by the finite-difference time-domain(FDTD)method.The simulated results show that the presented filter has good performance including a wide3-dB bandwidth of 149%from 0.57 GHz to 3.93 GHz,an extremely wide 40-dB upper-band rejection from 4.2 GHz to18.5 GHz,and low loss and high selectivity in the passband.To prove the design validity,a prototype of the BPF has been manufactured and measured,showing a reasonable agreement with simulation results.The unique features of the proposed BPF may make it applicable for integrated circuit and plasmonic devices in microwave or THz frequency ranges.展开更多
Modern electronic circuit requires compact,multifunctional technology in communication systems.However,it is very difficult due to the limitations in passive component miniaturization and the complication of fabricati...Modern electronic circuit requires compact,multifunctional technology in communication systems.However,it is very difficult due to the limitations in passive component miniaturization and the complication of fabrication process.The bandpass filter is one of the most important passive components in millimeter(mm)-wave communication system,attracting significant interest in three-dimension(3D) miniaturized design,which is few reported.In this paper,a bandpass filter structure using low-temperature co-fired ceramic(LTCC) technology,which is fully integrated in a system-in package(SIP) communication module,is presented for miniaturized and high reliable mm-wave application.The bandpass filter with 3D end-coupled microstrip resonators is implemented in order to achieve a high performance bandwidth characteristic.Specifically,all of the resonators are embedded into different ceramic layers to decrease the insertion loss and enhance the out-of-band rejection performance by optimizing the coupling coefficient and the coupling strength.A fence structure,which is formed by metal-filled via array with the gap less than quarter wavelength,is placed around the embedded bandpass filter to avoid electromagnetic(EM) interference problem in multilayer structure.This structural model is validated through actual LTCC process.The bandpass filter is successfully manufactured by modifying the co-fireablity characteristics,adjusting the sintering profile,releasing the interfacial stress,and reducing the shrinkage mismatch with different materials.Measured results show good performance and agree well with the high frequency EM full wave simulation.The influence of layer thickness and dielectric constant on the frequency response in fabricated process is analyzed,where thicker ceramic sheets let the filter response shift to higher frequency.Moreover,measured S-parameters denote the center frequency is also strongly influenced by the variation of ceramic material's dielectric constants.By analyzing the relationship between the characteristics of the ceramic tape and the center frequency of the filter,both theoretical and experimental data are accumulated for broadening application filed.With the coupling resonators embedded into the ceramic layers,the bandpass filter exhibits advantages of small size and high reliability compared to conventional planar filter structure,which makes the bandpass filter suitable for SIP communicational application.展开更多
A prototype IIR bandpass filter is derived from an analog bandpass filter using bilinear transformation. The formulas relating the IIR bandpass filter's coefficients with its centre frequency and bandwidth are obt...A prototype IIR bandpass filter is derived from an analog bandpass filter using bilinear transformation. The formulas relating the IIR bandpass filter's coefficients with its centre frequency and bandwidth are obtained. Using N sections of such filters, a cascade IIR bandpass filter is constructed. Based on given specifications and the formulas, the parameter N and the bandwidth of prototype filter can be obtained, and the required cascade IIR bandpass filter is obtained. The filter has a small set of coefficients with a simple structure, therefore is easy to design. The described approach is especially suitable for hardware implementation.展开更多
The development of wireless communication standards necessitates optimal filter design for the selection of appropriate bands of frequencies.In this work,a compact in size pair of parallel coupled symmetric stepped im...The development of wireless communication standards necessitates optimal filter design for the selection of appropriate bands of frequencies.In this work,a compact in size pair of parallel coupled symmetric stepped impedancebased resonator is designed with supporting to the WiMAX communication standards.The coupled resonator is tuned to allow the frequency band between 3.4 GHz and 3.8 GHz,which is centered at 3.6 GHz.A parasitic effect of capacitively coupled feed structure is used for exciting the two symmetrical stepped impedance resonators.The bandwidth and selectivity of the filter are enhanced with the change of characteristic impedances and controlling the coupling gap between resonators.This design offers single narrow sharp passband selectivity as well as multiple stopband harmonic suppression arising as a result of multiple transmission zeros.The designed filter operates with a fractional bandwidth(FBW)of 11.47%.The proposed single narrowband bandpass filter provides better suppression in either side of the tuned frequency(3.6 GHz)without degrading the passband performance.Also,this novel filter offers an insertion loss of about−0.08 dB and a return loss of greater than−30 dB in passband.This approach is useful for eliminating unwanted spurious harmonics responses that enter the desired response.The suggested bandpass filter has been simulated using Advanced Design System(ADS)tool,and the measurement has been made using a network analyzer,and the results are reported.展开更多
A miniaturized periodic element for constructing bandpass frequency selective surface(FSS)independent of incident angles and polarizations is presented.An interdigital resonator(IR)with one extending finger to connect...A miniaturized periodic element for constructing bandpass frequency selective surface(FSS)independent of incident angles and polarizations is presented.An interdigital resonator(IR)with one extending finger to connect the two separate parts of the interdigital capacitor is explored to achieve parallel resonance.The equivalent circuit model(ECM)and electric field distributions are introduced to explain frequency performance of FSS.The whole structure has only one layer and possesses a low profile(a thickness of 0.0015λ,where λ represents the resonant wavelength in free space)as well as a small size(0.03λ×0.03λ).This FSS performs as a spatial bandpass filter which exhibits a great angular stability with incident angles ranging from 0° to 80° for both transverse electric(TE)and transverse magnetic(TM)polarizations.As an example,a prototype of one proposed FSS is fabricated and tested.The measured results show a good angular stability.展开更多
In this paper, the resonant frequency of a dual\|mode dielectric resonator is calculated using a finite difference time\|domain method. A new type of bandpass filter is designed with the calculated coupling coefficien...In this paper, the resonant frequency of a dual\|mode dielectric resonator is calculated using a finite difference time\|domain method. A new type of bandpass filter is designed with the calculated coupling coefficient. The filter designed in this paper has reached the design goal, verified by simulation with Ansoft HFSS.展开更多
A high performance Balun BandPass Filter (BPF) with capacitively loaded multiple coupled lines with very simple structure is proposed in this paper, this structure realizes simultaneous size reduction and superior har...A high performance Balun BandPass Filter (BPF) with capacitively loaded multiple coupled lines with very simple structure is proposed in this paper, this structure realizes simultaneous size reduction and superior harmonic response suppression performance in bandpass filtering meanwhile good differential performance of the Balun. The theory of this structure for unbalanced input into balanced output has been studied in this paper and a proper Balun and BPF characteristic by the symmetric feeding and skew symmetric feeding have been obtained to prove the theory. The enter frequency of the fabricated Balun-BPF is operated at 2.45 GHz with 6.93% Fractional Band Width (FBW), and this frequency is used for Bluetooth and some other communication systems. The differences between the two outputs are 180°± 1.92° in phase and within 0.33 dB in magnitude. At f0, the amplitude imbalance and phase difference are within 0.25 dB and 180.86°, respectively. The measured frequency responses agree well with the simulated ones. With the theoretical analyses and practical results, it is shown that the proposed one has the advantages of simple structure, convenient analysis and good performance of both BPF and Balun.展开更多
In this paper,a Slotted Stepped-Impedance Resonator (SSIR) is proposed.Due to the slots in the low-impedance section of the conventional SIR,the new resonator has a lower fundamental resonance f0 and can provide a pot...In this paper,a Slotted Stepped-Impedance Resonator (SSIR) is proposed.Due to the slots in the low-impedance section of the conventional SIR,the new resonator has a lower fundamental resonance f0 and can provide a potential finite transmission zero fz close to f0.Based on the proposed SSIR,a fourth-order Chebychev BandPass Filter (BPF) is designed at f0=1 GHz.The measured results show that a better than-65 dB rejection is achieved on both the lower and the upper stopband.Moreover,the new filter has a wide-30 dB rejection upper stopband from 1.13f0 to 6.52f0.The fabricated filter exhibits a size of The new filter has a planar topology and is easily integrated with modern portable communication systems.展开更多
A wideband tunable frequency-doubling optoelectronic oscillator (FD-OEO) is proposed and experimentally demonstrated based on a polarization modulator and an optical bandpass filter (OBPF). The central frequency o...A wideband tunable frequency-doubling optoelectronic oscillator (FD-OEO) is proposed and experimentally demonstrated based on a polarization modulator and an optical bandpass filter (OBPF). The central frequency of the correspondingly fundamental OEO could be adjusted by tuning the bandwidth and central frequency of the OBPF, which could also be regarded as a photonic-assisted tunable microwave filter. The frequency tuning range of the FD-OEO covers from 9.5 to 32.8?GHz, and the single sideband phase noise of the fundamental signal is lower than -100dBc/Hz at an offset of 10?kHz. Moreover, the frequency stability of the generated signal is investigated by measuring its Allan deviation. The Allan deviation of the generated fundamental signal at 10?GHz is 2.39×10^-9.展开更多
In this paper, the variational method combined with Green's function is used to analyze the characteristics of suspended, stripline. The result is in good agreement with references. The design of mm-wave end-coupl...In this paper, the variational method combined with Green's function is used to analyze the characteristics of suspended, stripline. The result is in good agreement with references. The design of mm-wave end-coupled bandpass filter with suspended substrate is discussed. The computer programs for design of suspended stripline and bandpass filter are established.展开更多
Compact fifth-generation(5G)low-frequency band filtering antennas(filtennas)with stable directive radiation patterns,improved bandwidth(BW),and gain are designed,fabricated,and tested in this research.The proposed fil...Compact fifth-generation(5G)low-frequency band filtering antennas(filtennas)with stable directive radiation patterns,improved bandwidth(BW),and gain are designed,fabricated,and tested in this research.The proposed filtennas are achieved by combining the predesigned compact 5G(5.975–7.125 GHz)third-order uniform and non-uniform transmission line hairpin bandpass filters(UTL and NTL HPBFs)with the compact ultrawide band Vivaldi tapered slot antenna(UWB VTSA)in one module.The objective of this integration is to enhance the performance of 5.975–7.125GHz filtennas which will be suitable for modern mobile communication applications by exploiting the benefits of UWB VTSA.Based on NTL HPBF,more space is provided to add the direct current(DC)biassing circuits in cognitive radio networks(CRNs)for frequency reconfigurable applications.To overcome the mismatch between HPBFs and VTSA,detailed parametric studies are presented.Computer simulation technology(CST)software is used for the simulation in this study.Good measured S11 appeared to be<−13 and<−10.54 dB at 5.48–7.73 and 5.9–7.98GHz with peak realized gains of 6.37 and 6.27 dBi,for VTSA with UTL and NTL HPBFs,respectively which outperforms the predesigned filters.Validation is carried out by comparing the measured and simulated results.展开更多
The probability hypothesis density (PHD), a well-known scheme for multi-target tracking in clutters, can obtain peaks of possible tracks, and its cluster-indexed method is widely accepted in further track extraction. ...The probability hypothesis density (PHD), a well-known scheme for multi-target tracking in clutters, can obtain peaks of possible tracks, and its cluster-indexed method is widely accepted in further track extraction. However, the track extraction may face high risk in the case that the targets are so approached that it is hardly to discern their measurements. The concept of the distance between track sets in two adjacent times is defined and a consistency measure metric between any two peaks in two adjacent times is further proposed based on 'global information', containing spatial information (topology feature) among tracks, along with the temporal information of each track. Then, a global track extraction method is proposed based on the consistency belief and four decision rules. Via the simulation comparison with the cluster-indexed method, the proposed method can avoid the track break and mistake association. ? 2016 Beijing Institute of Aerospace Information.展开更多
基金supported by National Natural Science Foundations of China (No.61971052 and No.U20A20203)Key Research and Development Project of Guangdong Province (2020B0101080001)
文摘In this paper,a 5G wideband power amplifier(PA)with bandpass filtering response is synthesized using a bandwidth-extended bandpass filter as the matching network(MN).In this structure,the bandwidth(θ_(C))is defined as a variable in the closedform equations provided by the microstrip bandpass filter.It can be extended over a wide range only by changing the characteristic impedances of the structure.Different from the other wideband MNs,the extension of bandwidth does not increase the complexity of the structure(order n is fixed).In addition,based on the bandwidth-extended structure,the wideband design of bandpass filtering PA is not limited to the fixed bandwidth of the specific filter structure.The theoretical analysis of the MN and the design flow of the PA are provided in this design.The fabricated bandpass filtering PA can support almost one-octave bandwidth(2-3.8 GHz),covering the two 5G bands(n41 and n78).The drain efficiency of 47%-60%and output power higher than 40 dBm are measured.Good frequency selectivity in S-parameter measurements can be observed.
文摘A class of new planar dual-mode filters without coupling gaps is proposed. The proposed structures use a single patch wiuhout coupling gaps. Attenuation poles can be implemented on either side of the passband by changing the locations of two feed lines. By cutting two corners in the patch, two attenuation poles on both sides of passband are implemented. A novel dual-mode elliptic-function bandpass filter structure without coupling gaps is also proposed. These new filters can provide a low insertion loss and reduce uncertainty in fabrication owing to the absence of coupling gaps.
文摘This paper reviews the state-of-the-art filter designs for 60 GHz applications. The most promising filter solutions at this frequency include fiher-in-package where the filter itself is design in the packaging platform and filter-on-chip which is an on-chip filter co-design for miniaturized system size with low packaging cost. Design methodology, design technology, key performance parameters, similarities and dift)rences, advantages and drawbacks, and future trends are explored and studied. Filters in the printed circuit board (PCB), low temperature co-fired ceramics (LTCC), organie material, and bipolar complementary metal oxide semicomtuctor (BiCMOS) chips are summarized and compared in details. Future design trends and challenges are also given after the review.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.11504418,11447033,and 61372048)the Fundamental Research Funds for the Central Universities,China(Grant No.2015XKMS075)
文摘We report the design of a novel multiband metamaterial bandpass filter (BPF) in the terahertz (THz)-wave region. The designed BPF is composed of a metal-dielectric-metal sandwiched structure with three nested rings on the top surface and a cross structure on the bottom surface. Full-wave simulation results show that the designed BPF has three transmission peaks at frequencies of 0.42, 1.27, and 1.86 THz with transmission rates of-0.87,-1.85, and-1.83 dB, respectively. Multi-reflection interference theory is introduced to explain the transmission mechanism of the designed triple-band BPF. The theoretical transmission spectrum is in good agreement with the full-wave simulated results. The designed BPF can maintain a stable performance as the incident angle varies from 0 to 30 for both transverse electric and transverse magnetic polarizations of the incident wave. The designed BPF can be potentially used in THz devices due to its multiband transmissions, polarization insensitivity, and stable wide-angle response in the THz region.
基金Project supported by the Key Grant Project of Ministry of Education of China(Grant No.313029)the FDCT Research Grant from Macao Science and Technology Development Fund,China(Grant No.051/2014/A1)the Multi-Year Research Grant from University of Macao,Macao SAR,China(Grant No.MYRG2014-00079-FST)
文摘We investigate the guiding modes of spoof surface plasmon polaritons (SPPs) on a symmetric ultra-thin plasmonic structure. From the analysis, we deduce the operating frequency region of the single-mode propagation. Based on this property, a spoof SPPs lowpass filter is then constituted in the microwave frequency. By introducing a transmission zero at the lower frequency band using a pair of stepped-impedance stubs, a wide passband filter is further realized. The proposed filter is fed by.a transducer composed of a microstrip line with a flaring ground. The simulated results show that the presented filter has an extremely wide upper stopband in addition to excellent passband filtering characteristics such as low loss, wide band, and high square ratio. A prototype passband filter is also fabricated to validate the predicted performances. The proposed spoof-SPPs filter is believed to be very promising for other surface waveguide components in microwave and terahertz bands.
文摘This study is concerned with the diagnosis of discrepancies in a steel truss bridge by identifying dynamic properties from the vibration response signals of the bridges.The vibration response signals collected at bridges under three different vehicular speeds of 10 km/hr,20 km/hr,and 30 km/hr are analyzed using statistical features such as kurtosis,magnitude of peak-to-peak,root mean square,crest factor as well as impulse factor in time domain,and Stockwell transform in the time-frequency domain.The considered statistical features except for kurtosis show uncertain behavior.The Stockwell transform showed low-resolution outcomes when the presence of noise in the recorded vibration responses.The elimination of noise and extraction of meaningful dynamic properties from the vibration responses is done by applying a new method which comes from the fusion of Hilbert transform with Spectral kurtosis and bandpass filtering.The outcomes obtained from Hilbert transform processed residual signals which are further filtered using bandpass filter show more robustness and accuracy in characterizing bridge modal frequencies from the noisy vibration responses.The proposed method produces a high-resolution frequency response which can unveil the joint discrepancy in the bridge structure.
基金supported by the National Key Scientific Instrument and Equipment Development Project,China(Grant No.2014YQ030975)the National Natural Science Foundation of China(Grant Nos.61371009 and 61401282)
文摘In this study, we propose a novel resonator that is composed of a modified spiral with an embedded interdigital capacitor. A large ratio of the first spurious frequency to the fundamental resonant frequency is obtained, which is suitable for the design of filters with wide stopbands, and the circuit size is considerably reduced by embedding the interdigital structure in the spiral. For demonstration, a compact four-pole high temperature superconducting(HTS) filter with a center frequency of 568 MHz is designed and fabricated on double-sided YBCO film with a size of 11.4 mm×8.0 mm. The filter measurement shows excellent performance with an out-of-band rejection level better than 60.9 dB up to 3863 MHz.
基金the National Natural Science Foundation of China(Grant Nos.62071221 and 62071442)the Equipment Advance Research Foundation of China(Grant No.80909010302)the Key Laboratory of Radar Imaging and Microwave Photonics(Nanjing University of Aeronautics and Astronautics),Ministry of Education of China(Grant No.NJ20210006).
文摘A novel bandpass filter(BPF)based on spoof surface plasmon polaritons(SSPPs)using a compact folded slotline structure is proposed and experimentally demonstrated.The proposed novel SSPPs structure compared with a conventional plasmonic waveguide with slot line SSPPs unit structure at the same size,the considerable advantages in much lower asymptotic frequency with tight field confinement,which enable the proposed filter to be more miniaturization.A high-efficient mode conversion structure is designed to transition from TE-mode to SSPPs-mode by gradient slotline lengths.The low-frequency stop-band can be committed with microstrip to slotline evolution on both sides of the dielectric,while the high-frequency cutoff band is realized by the proposed SSPPs structure.The influence of dispersion relation,electric field distribution,surface current,and structural parameters on the transmission characteristics of the proposed BPF are analyzed by finite difference time domain(FDTD).To validate the design concept,the prototype of the miniaturized SSPPs BPF has been manufactured and measured.The experimental results show high performance of the fabricated sample,in which the working in a range of 0.9 GHz-5.2 GHz with the relative bandwidth is 142%,the insertion loss less than 0.5 dB,the reflection coefficient less than-10 dB,and the group delay is less than one ns.This works provides a mirror for realizing the miniaturization of waveguides,and the application and development of high-confinement SSPPs functional devices in the microwave and THz regimes.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.U2141232,62071221,and 62071442)the Aeronautical Science Foundation of China(Grant No.2019ZA037001)。
文摘An ultra-wideband bandpass filter(BPF)with a wide out-of-band rejection based on a surface plasmonic waveguide(SPW)slotline with ring grooves is designed and analyzed.A paired microstrip-to-slotline transition is designed for quasiTEM to TM mode conversion by using a microstrip line with a circular pad and the slotline with the same circular slot.The mode conversion between the TM and the surface plasmon polariton(SPP)mode is realized by using a gradient slotline with ring grooves and an impedance matching technique.The upper cut-off frequencies of the passband can be adjusted by using these proposed SPP units,while the lower frequencies of the passband are created by using the microstrip-toslotline transitions to give an ultra-wideband BPF.The dispersion curves of SPP units,electric field distribution,and the transmission spectra of the proposed ultra-wideband bandpass filter are all calculated and analyzed by the finite-difference time-domain(FDTD)method.The simulated results show that the presented filter has good performance including a wide3-dB bandwidth of 149%from 0.57 GHz to 3.93 GHz,an extremely wide 40-dB upper-band rejection from 4.2 GHz to18.5 GHz,and low loss and high selectivity in the passband.To prove the design validity,a prototype of the BPF has been manufactured and measured,showing a reasonable agreement with simulation results.The unique features of the proposed BPF may make it applicable for integrated circuit and plasmonic devices in microwave or THz frequency ranges.
基金supported by Research Fund for the Doctoral Program of Higher Education of China(Grant No.20060614021)Sichuan Provincial Fundamental Research of China(Grant No.2008JY0057),Fundamental Research Funds for the Central Universities of China(Grant No.ZYGX2009J091)
文摘Modern electronic circuit requires compact,multifunctional technology in communication systems.However,it is very difficult due to the limitations in passive component miniaturization and the complication of fabrication process.The bandpass filter is one of the most important passive components in millimeter(mm)-wave communication system,attracting significant interest in three-dimension(3D) miniaturized design,which is few reported.In this paper,a bandpass filter structure using low-temperature co-fired ceramic(LTCC) technology,which is fully integrated in a system-in package(SIP) communication module,is presented for miniaturized and high reliable mm-wave application.The bandpass filter with 3D end-coupled microstrip resonators is implemented in order to achieve a high performance bandwidth characteristic.Specifically,all of the resonators are embedded into different ceramic layers to decrease the insertion loss and enhance the out-of-band rejection performance by optimizing the coupling coefficient and the coupling strength.A fence structure,which is formed by metal-filled via array with the gap less than quarter wavelength,is placed around the embedded bandpass filter to avoid electromagnetic(EM) interference problem in multilayer structure.This structural model is validated through actual LTCC process.The bandpass filter is successfully manufactured by modifying the co-fireablity characteristics,adjusting the sintering profile,releasing the interfacial stress,and reducing the shrinkage mismatch with different materials.Measured results show good performance and agree well with the high frequency EM full wave simulation.The influence of layer thickness and dielectric constant on the frequency response in fabricated process is analyzed,where thicker ceramic sheets let the filter response shift to higher frequency.Moreover,measured S-parameters denote the center frequency is also strongly influenced by the variation of ceramic material's dielectric constants.By analyzing the relationship between the characteristics of the ceramic tape and the center frequency of the filter,both theoretical and experimental data are accumulated for broadening application filed.With the coupling resonators embedded into the ceramic layers,the bandpass filter exhibits advantages of small size and high reliability compared to conventional planar filter structure,which makes the bandpass filter suitable for SIP communicational application.
文摘A prototype IIR bandpass filter is derived from an analog bandpass filter using bilinear transformation. The formulas relating the IIR bandpass filter's coefficients with its centre frequency and bandwidth are obtained. Using N sections of such filters, a cascade IIR bandpass filter is constructed. Based on given specifications and the formulas, the parameter N and the bandwidth of prototype filter can be obtained, and the required cascade IIR bandpass filter is obtained. The filter has a small set of coefficients with a simple structure, therefore is easy to design. The described approach is especially suitable for hardware implementation.
文摘The development of wireless communication standards necessitates optimal filter design for the selection of appropriate bands of frequencies.In this work,a compact in size pair of parallel coupled symmetric stepped impedancebased resonator is designed with supporting to the WiMAX communication standards.The coupled resonator is tuned to allow the frequency band between 3.4 GHz and 3.8 GHz,which is centered at 3.6 GHz.A parasitic effect of capacitively coupled feed structure is used for exciting the two symmetrical stepped impedance resonators.The bandwidth and selectivity of the filter are enhanced with the change of characteristic impedances and controlling the coupling gap between resonators.This design offers single narrow sharp passband selectivity as well as multiple stopband harmonic suppression arising as a result of multiple transmission zeros.The designed filter operates with a fractional bandwidth(FBW)of 11.47%.The proposed single narrowband bandpass filter provides better suppression in either side of the tuned frequency(3.6 GHz)without degrading the passband performance.Also,this novel filter offers an insertion loss of about−0.08 dB and a return loss of greater than−30 dB in passband.This approach is useful for eliminating unwanted spurious harmonics responses that enter the desired response.The suggested bandpass filter has been simulated using Advanced Design System(ADS)tool,and the measurement has been made using a network analyzer,and the results are reported.
基金supported by the Aeronautical Science Foundation of China(2017ZF37005)the National Natural Science Foundation of China(62001389).
文摘A miniaturized periodic element for constructing bandpass frequency selective surface(FSS)independent of incident angles and polarizations is presented.An interdigital resonator(IR)with one extending finger to connect the two separate parts of the interdigital capacitor is explored to achieve parallel resonance.The equivalent circuit model(ECM)and electric field distributions are introduced to explain frequency performance of FSS.The whole structure has only one layer and possesses a low profile(a thickness of 0.0015λ,where λ represents the resonant wavelength in free space)as well as a small size(0.03λ×0.03λ).This FSS performs as a spatial bandpass filter which exhibits a great angular stability with incident angles ranging from 0° to 80° for both transverse electric(TE)and transverse magnetic(TM)polarizations.As an example,a prototype of one proposed FSS is fabricated and tested.The measured results show a good angular stability.
文摘In this paper, the resonant frequency of a dual\|mode dielectric resonator is calculated using a finite difference time\|domain method. A new type of bandpass filter is designed with the calculated coupling coefficient. The filter designed in this paper has reached the design goal, verified by simulation with Ansoft HFSS.
文摘A high performance Balun BandPass Filter (BPF) with capacitively loaded multiple coupled lines with very simple structure is proposed in this paper, this structure realizes simultaneous size reduction and superior harmonic response suppression performance in bandpass filtering meanwhile good differential performance of the Balun. The theory of this structure for unbalanced input into balanced output has been studied in this paper and a proper Balun and BPF characteristic by the symmetric feeding and skew symmetric feeding have been obtained to prove the theory. The enter frequency of the fabricated Balun-BPF is operated at 2.45 GHz with 6.93% Fractional Band Width (FBW), and this frequency is used for Bluetooth and some other communication systems. The differences between the two outputs are 180°± 1.92° in phase and within 0.33 dB in magnitude. At f0, the amplitude imbalance and phase difference are within 0.25 dB and 180.86°, respectively. The measured frequency responses agree well with the simulated ones. With the theoretical analyses and practical results, it is shown that the proposed one has the advantages of simple structure, convenient analysis and good performance of both BPF and Balun.
文摘In this paper,a Slotted Stepped-Impedance Resonator (SSIR) is proposed.Due to the slots in the low-impedance section of the conventional SIR,the new resonator has a lower fundamental resonance f0 and can provide a potential finite transmission zero fz close to f0.Based on the proposed SSIR,a fourth-order Chebychev BandPass Filter (BPF) is designed at f0=1 GHz.The measured results show that a better than-65 dB rejection is achieved on both the lower and the upper stopband.Moreover,the new filter has a wide-30 dB rejection upper stopband from 1.13f0 to 6.52f0.The fabricated filter exhibits a size of The new filter has a planar topology and is easily integrated with modern portable communication systems.
基金Supported by the National Natural Science Foundation of China under Grant No 61675196the National Basic Research Program of China under Grant No 2014CB340102+1 种基金the National High-Tech Research and Development Program of China under Grant No 2015AA016903the Open Research of Beijing University of Posts and Telecommunications under Grant No IOOC2013A002
文摘A wideband tunable frequency-doubling optoelectronic oscillator (FD-OEO) is proposed and experimentally demonstrated based on a polarization modulator and an optical bandpass filter (OBPF). The central frequency of the correspondingly fundamental OEO could be adjusted by tuning the bandwidth and central frequency of the OBPF, which could also be regarded as a photonic-assisted tunable microwave filter. The frequency tuning range of the FD-OEO covers from 9.5 to 32.8?GHz, and the single sideband phase noise of the fundamental signal is lower than -100dBc/Hz at an offset of 10?kHz. Moreover, the frequency stability of the generated signal is investigated by measuring its Allan deviation. The Allan deviation of the generated fundamental signal at 10?GHz is 2.39×10^-9.
文摘In this paper, the variational method combined with Green's function is used to analyze the characteristics of suspended, stripline. The result is in good agreement with references. The design of mm-wave end-coupled bandpass filter with suspended substrate is discussed. The computer programs for design of suspended stripline and bandpass filter are established.
基金This work was supported by the Postdoctoral Fellowship Scheme under the Professional Development Research University from Universiti Teknologi Malaysia(UTM)under Grant 06E07.
文摘Compact fifth-generation(5G)low-frequency band filtering antennas(filtennas)with stable directive radiation patterns,improved bandwidth(BW),and gain are designed,fabricated,and tested in this research.The proposed filtennas are achieved by combining the predesigned compact 5G(5.975–7.125 GHz)third-order uniform and non-uniform transmission line hairpin bandpass filters(UTL and NTL HPBFs)with the compact ultrawide band Vivaldi tapered slot antenna(UWB VTSA)in one module.The objective of this integration is to enhance the performance of 5.975–7.125GHz filtennas which will be suitable for modern mobile communication applications by exploiting the benefits of UWB VTSA.Based on NTL HPBF,more space is provided to add the direct current(DC)biassing circuits in cognitive radio networks(CRNs)for frequency reconfigurable applications.To overcome the mismatch between HPBFs and VTSA,detailed parametric studies are presented.Computer simulation technology(CST)software is used for the simulation in this study.Good measured S11 appeared to be<−13 and<−10.54 dB at 5.48–7.73 and 5.9–7.98GHz with peak realized gains of 6.37 and 6.27 dBi,for VTSA with UTL and NTL HPBFs,respectively which outperforms the predesigned filters.Validation is carried out by comparing the measured and simulated results.
基金supported by the National Natural Science Foundation of China(611350016137402361374159)
文摘The probability hypothesis density (PHD), a well-known scheme for multi-target tracking in clutters, can obtain peaks of possible tracks, and its cluster-indexed method is widely accepted in further track extraction. However, the track extraction may face high risk in the case that the targets are so approached that it is hardly to discern their measurements. The concept of the distance between track sets in two adjacent times is defined and a consistency measure metric between any two peaks in two adjacent times is further proposed based on 'global information', containing spatial information (topology feature) among tracks, along with the temporal information of each track. Then, a global track extraction method is proposed based on the consistency belief and four decision rules. Via the simulation comparison with the cluster-indexed method, the proposed method can avoid the track break and mistake association. ? 2016 Beijing Institute of Aerospace Information.