The presence of waste tires poses an environmental challenge as they occupy a significant amount of land and are expensive to dispose in landfills.However,reusing waste tires can address this issue when waste tires ar...The presence of waste tires poses an environmental challenge as they occupy a significant amount of land and are expensive to dispose in landfills.However,reusing waste tires can address this issue when waste tires are used in geotechnical applications.To determine the viability of this approach,laboratoryscale tests were conducted to investigate load-bearing capacity of circular footings on sand-tire shred(STS)mixtures with shredded waste tire contents of 5%e15%by weight and three different widths of shreds.The investigation focused on analyzing the thickness of layers composed of STS mixtures,the soil cap,and the impact of geogrids on bearing capacity.The results indicate that a specific mixture of sand and tire shreds provides the highest footing-bearing capacity.In addition,the optimal shred content and size were found to be 10%by weight and 2 cm×10 cm,respectively.Furthermore,for a given tire shred width,a particular length provides the largest bearing capacity.The results agree well with that of previous research conducted by the first author and his colleagues in direct shear and California bearing ratio(CBR)tests.The primary finding of this research is that the use of two-layered STS mixtures reinforced by geogrids significantly enhances the bearing capacity.展开更多
A theoretical analysis of upward deflection and midspan deflection of prestressed bamboo-steel composite beams is presented in this study.The deflection analysis considers the influences of interface slippage and shea...A theoretical analysis of upward deflection and midspan deflection of prestressed bamboo-steel composite beams is presented in this study.The deflection analysis considers the influences of interface slippage and shear deformation.Furthermore,the calculation model for flexural capacity is proposed considering the two stages of loading.The theoretical results are verified with 8 specimens considering different prestressed load levels,load schemes,and prestress schemes.The results indicate that the proposed theoretical analysis provides a feasible prediction of the deflection and bearing capacity of bamboo-steel composite beams.For deflection analysis,the method considering the slippage and shear deformation provides better accuracy.The theoretical method for bearing capacity matches well with the test results,and the relative errors in the serviceability limit state and ultimate limit state are 4.95%and 5.85%,respectively,which meet the accuracy requirements of the engineered application.展开更多
A bridge project is taken as an example to analyze the application of bearing capacity detection and evaluation.This article provides a basic overview of the project,the application of bearing capacity detection techn...A bridge project is taken as an example to analyze the application of bearing capacity detection and evaluation.This article provides a basic overview of the project,the application of bearing capacity detection technology,and the bearing capacity assessment analysis.It is hoped that this analysis can provide a scientific reference for the load-bearing capacity detection and evaluation work in bridge engineering projects,thereby achieving a scientific assessment of the overall load-bearing capacity of the bridge engineering structure.展开更多
The bearing capacity testing and evaluation of the existing bridge engineering structure is not only the key to clarify its structural quality and safety performance,but it also can lay a solid foundation for subseque...The bearing capacity testing and evaluation of the existing bridge engineering structure is not only the key to clarify its structural quality and safety performance,but it also can lay a solid foundation for subsequent repairs and maintenance work.To ensure the bearing capacity,durability and reliability of existing bridges,this paper analyzes the importance and methods of testing and evaluation of structural bearing capacity of a bridge.This analysis aims to provide scientific reference for the quality assessment and subsequent repair and maintenance of existing bridge engineering structures.展开更多
This paper aims to determine the load bearing capacity of pre-stressed expandable props with different geometries and load eccentricities for flexible support in underground mining or excavation.It is deduced that the...This paper aims to determine the load bearing capacity of pre-stressed expandable props with different geometries and load eccentricities for flexible support in underground mining or excavation.It is deduced that the expandable device could have much higher strength(>89 MPa)by laboratory tests,and the load bearing capacity of the expandable prop may depend on the stability of the supporting steel pipe structure.A good agreement was found between the laboratory test and numerical results in terms of the load bearing capacity and the final macro-bending failure pattern for expandable props with heights of 1.5 and 2.7 m,and the theoretical calculation for the strength of traditional steel structures is not directly suitable for the expandable props.Moreover,additional numerical simulations were performed for the expandable props with different normalized slenderness ratiosλ_(n)and loading eccentric distances e.The variation of stability coefficient of the expandable prop is in line with the Perry-Robertson equation and its correlation coefficients are fitted as a of 0.979 and b of 0.314.For estimating the load bearing capacity of the expandable props,the strength equation for traditional steel structures is improved by introducing a bending magnification factor and by modifying the normalized slenderness ratio to a converted slenderness ratio.Based on the underground field monitoring for the strength of expandable props with different heights,the empirical eccentric distances were back calculated,and a safety factor is introduced to obtain the designed strength of the expandable prop.In addition,a four-step design procedure is proposed for the expandable prop.展开更多
This paper investigates the validity and shortcomings of the existing analytical solution for the ultimate bearing capacity of a pile embedded in a rock mass using the modified HoekeBrown failure criterion.Although th...This paper investigates the validity and shortcomings of the existing analytical solution for the ultimate bearing capacity of a pile embedded in a rock mass using the modified HoekeBrown failure criterion.Although this criterion is considered a reference value for empirical and numerical calculations,some limitations of its basic simplifications have not been clarified yet.This research compares the analytical results obtained from the novel discontinuity layout optimization(DLO)method and the numerical solutions from the finite difference method(FDM).The limitations of the analytical solution are considered by comparing different DLO failure modes,thus allowing for the first time a critical evaluation of its scope and conditioning for implementation.Errors of up to 40%in the bearing capacity and unrealistic failure modes are the main issues in the analytical solution.The main aspects of the DLO method are also analyzed with an emphasis on the linearization of the rock failure criterion and the accuracy resulting from the discretization size.The analysis demonstrates DLO as a very efficient and accurate tool to address the pile tip bearing capacity,presenting considerable advantages over other methods.展开更多
Slope bearing capacity is one of the most important characteristics in slope engineering and is strongly influenced by weak planes,loading conditions,and slope geometry.By presenting the evolution of slip surfaces,thi...Slope bearing capacity is one of the most important characteristics in slope engineering and is strongly influenced by weak planes,loading conditions,and slope geometry.By presenting the evolution of slip surfaces,this paper explored how the slope bearing capacity is affected by widely observed influencing factors.The initiation and propagation of slip surfaces are presented in laboratory model tests of slope using the transparent soil technique.Shear band evolution under various weak planes,loading conditions,and slope geometries were experimentally presented,and slope bearing capacities were analyzed with the process of shear band evolution.This paper verified that slip surface morphologies have a strong relation with the slope bearing capacity.The same slip surface morphology can have different evolutionary processes.In this case,it is the shear band evolution that determines the slope bearing capacity,not the morphology of the slip surface.The influencing factors such as pre-existing weak planes,loading conditions,and slope geometry strongly affect the slope bearing capacity as these factors govern the process of shear band evolution inside the slope.展开更多
Ultimate bearing capacity(UBC)is a key subject in geotechnical/foundation engineering as it determines the limit of loads imposed on the foundation.The most reliable means of determining UBC is through experiment,but ...Ultimate bearing capacity(UBC)is a key subject in geotechnical/foundation engineering as it determines the limit of loads imposed on the foundation.The most reliable means of determining UBC is through experiment,but it is costly and time-consuming which has led to the development of various models based on the simplified assumptions.The outcomes of the models are usually validated with the experimental results,but a large gap usually exists between them.Therefore,a model that can give a close prediction of the experimental results is imperative.This study proposes a grasshopper optimization algorithm(GOA)and salp swarm algorithm(SSA)to optimize artificial neural networks(ANNs)using the existing UBC experimental database.The performances of the proposed models are evaluated using various statistical indices.The obtained results are compared with the existing models.The proposed models outperformed the existing models.The proposed hybrid GOA-ANN and SSA-ANN models are then transformed into mathematical forms that can be incorporated into geotechnical/foundation engineering design codes for accurate UBC measurements.展开更多
Artificial cementation is a method commonly used to enhance and improve soil properties. This paper investigates the effect of using different amounts of cement on soil strength parameters and soil bearing capacity, u...Artificial cementation is a method commonly used to enhance and improve soil properties. This paper investigates the effect of using different amounts of cement on soil strength parameters and soil bearing capacity, using the finite element method. Experimental tests are conducted on soil samples with different amounts of Portland cement. A 2-D numerical model is created and validated using the numerical modelling software, COMSOL Multiphysics 5.6 software. The study finds that the cohesion, and the angle of the internal friction of the soil samples increase significantly as a result of adding 1%, 2%, and 4% of Portland cement. The results demonstrate that the stresses and strain under the strip footing proposed decrease by 3.24% and 7.42%. Moreover, the maximum displacement also decreases by 1.47% and 2.97%, as a result of adding cements of 2% and 4%. The bearing capacity values obtained are therefore excellent, especially when using the 2% and 4% cement. The increase identified is due to the increased values of the bearing capacity factors. It is concluded that from an economic viewpoint, using 2% cement is the best option.展开更多
This study addresses the pressing need to assess foundation bearing capacity in Opolo,Yenagoa,Bayelsa State,Nigeria.The significance lies in the dearth of comprehensive geotechnical data for construction planning in t...This study addresses the pressing need to assess foundation bearing capacity in Opolo,Yenagoa,Bayelsa State,Nigeria.The significance lies in the dearth of comprehensive geotechnical data for construction planning in the region.Past research is limited and this study contributes valuable insights by integrating Geographic Information System(GIS)with the Generalized Reciprocal Method(GRM).To collect data,near-surface seismic refraction surveys were conducted along three designated lines,utilizing ABEM Terraloc Mark 6 equipment,Easy Refract,and ArcGIS 10.4.1 software.This methodology allowed for the determination of key geotechnical parameters essential for soil characterization at potential foundation sites.The results revealed three distinct geoseismic layers.The uppermost layer,within a depth of 0.89 to 1.50 meters,exhibited inadequate compressional and shear wave velocities and low values for oedometric modulus,shear modulus,N-value,ultimate bearing capacity,and allowable bearing capacity.This indicates the presence of unsuitable,soft,and weak alluvial deposits for substantial structural loads.In contrast,the second layer(1.52 to 3.84 m depth)displayed favorable geotechnical parameters,making it suitable for various construction loads.The third layer(15.00 to 26.05 m depth)exhibited varying characteristics.The GIS analysis highlighted the unsuitability of the uppermost layer for construction,while the second and third layers were found to be fairly competent and suitable for shallow footing and foundation design.In summary,this study highlights the importance of geotechnical surveys in Opolo’s construction planning.It offers vital information for informed choices,addresses issues in the initial layer,and suggests secure,sustainable construction options.展开更多
The paper presents conclusions related to the design of shallow foundations,at the site where the Substation at Kashari,in Tirana is foreseen to be constructed.The project includes buildings with small to medium struc...The paper presents conclusions related to the design of shallow foundations,at the site where the Substation at Kashari,in Tirana is foreseen to be constructed.The project includes buildings with small to medium structures with 1-3 stories.The geological survey works include 6 boreholes of a depth 20.0 m,90 SPT(Standard Penetration Tests)tests,and laboratory works include 13 direct shear tests,27 unconfined and compressive strength tests,7 CU(consolidated undrained)tests and 9 UU(unconsolidated undrained)tests,etc.The foundation design must fulfill both,bearing and settlement criteria,but in this case the settlements of foundations are not possible to be calculated,since the laboratory works do not include any consolidation test.So,the local bearing capacity is expected to control the design in terms of bearing capacity and settlements.The local bearing capacity of shallow square foundations is evaluated by using Terzaghi’s formula,based on reduced shear strength parameters of soils below the bottom of foundations.The results are compared with the bearing capacity values calculated by using Burland and Burbdige(1984)method,based on the data of SPT tests.This method is used for checking the settlement(serviceability)criterion in the foundation design,when the direct settlement calculation is missing.The paper presents some conclusions related to local bearing capacity foundation-based design.展开更多
Suction caisson foundations are often subjected to vertical uplift loads,but there are still no wide and spread engineering specifications on design and calculation method for uplift bearing capacity of suction caisso...Suction caisson foundations are often subjected to vertical uplift loads,but there are still no wide and spread engineering specifications on design and calculation method for uplift bearing capacity of suction caisson foundation.So it is important to establish an uplift failure criterion.In order to study the uplift bearing mechanism and failure mode of suction caisson foundation,a series of model tests were carried out considering the effects of aspect ratio,soil permeability and loading mode.Test results indicate that the residual negative pressure at the top of caisson is beneficial to enhance uplift bearing capacity.The smaller the permeability coefficient is,the higher the residual negative pressure will be.And the residual negative pressure is approximately equal to the water head that causes seepage in the caisson.When the load reaches the ultimate bearing capacity,both the top and bottom negative pressures are smaller than Su and both the top and bottom reverse bearing capacity factors are smaller than 1.0 in soft clay.Combined the uplift bearing characteristics of caisson in sandy soil and soft clay,the bearing capacity composition and the calculation method are proposed.It can provide a reference for the engineering design of suction caisson foundation under vertical load.展开更多
Low gravity fields have been simulated through magnetic acceleration to conduct experimental study on bearing capacity of circular footings on a type of crushable planetary regolith simulant,which has comparable densi...Low gravity fields have been simulated through magnetic acceleration to conduct experimental study on bearing capacity of circular footings on a type of crushable planetary regolith simulant,which has comparable density and particle size distribution of lunar soil.The loadesettlement responses of surface spread footings are obtained by investigating the relative density,footing size and gravity effects.Applying the hyperbolic asymptote method,normalised foundation stiffness and ultimate bearing capacity are obtained by curve fitting and predicted by power functions using multivariate nonlinear regression.The results show that the nonlinear gravity effect is not negligible,related to stress condition,soil dilatancy and mobilised friction angle.A cone penetration test(CPT)-based method for prediction of bearing capacity is proposed with correlations between ultimate bearing capacity of footings and shallow penetration stiffness of CPTs,avoiding the uncertainties of soil property estimations.Analyses of allowable bearing capacity and footing influence zone in consideration of footing size and gravity effects could therefore improve the design of shallow foundations on the Moon and Mars,and provide new understandings and potential implications to the bearing capacity of shallow foundations on crushable granular material in both terrestrial and extraterrestrial geotechnical engineering.展开更多
Reducing the cost of offshore platform construction is an urgent issue for marginal oilfield development.The offshore oil well structure includes a riser and a surface casing.The riser,surface casing and oil well ceme...Reducing the cost of offshore platform construction is an urgent issue for marginal oilfield development.The offshore oil well structure includes a riser and a surface casing.The riser,surface casing and oil well cement can be considered special variable cross-section piles.Replacing or partially replacing the steel pipe pile foundation with a variable cross-section pile to provide the required bearing capacity for an offshore oil platform can reduce the cost of foundation construction and improve the economic efficiency of production.In this paper,the finite element analysis method is used to investigate the variable cross-section bearing mode of composite piles composed of a riser and a surface casing in saturated clay under a vertical load.The calculation formula of the bearing capacity at the variable section is derived based on the theory of spherical cavity expansion,the influencing factors of the bearing capacity coefficient N_(c) are revealed,and the calculation method of N_(c) is proposed.By comparing the calculation results with the results of the centrifuge test,the accuracy and applicability of the calculation method are verified.The results show that the riser composite pile has a rigid core in the soil under the variable cross-section,which increases the bearing capacity at the variable cross-section.展开更多
Suction caisson foundation derives most of their uplift resistance from passive suction developed during the pullout movement. It was observed that the passive suction generated in soil at the bottom of the caisson an...Suction caisson foundation derives most of their uplift resistance from passive suction developed during the pullout movement. It was observed that the passive suction generated in soil at the bottom of the caisson and the failure mode of suction caisson foundation subjecting pullout loading behaves as a reverse compression failure mechanism.The upper bound theorems have been proved to be a powerful method to find the critical failure mechanism and critical load associated with foundations, buried caissons and other geotechnical structures. However, limited attempts have been reported to estimate the uplift bearing capacity of the suction caisson foundation using the upper bound solution. In this paper, both reverse failure mechanisms from Prandtl and Hill were adopted as the failure mechanisms for the computation of the uplift bearing capacity of the suction caisson. New equations were proposed based on both failure mechanisms to estimate the pullout capacity of the suction caisson. The proposed equations were verified by the test results and experimental data from published literature. And the two solutions agree reasonably well with the other test results. It can be proved that both failure mechanisms are reasonably and more consistent with the actual force condition.展开更多
A bearing capacity evaluation for the surface strip foundation on a working platform modelled on a twolayered substrate is considered in the study.The upper layer is assumed as man-made and wellcontrolled and thus non...A bearing capacity evaluation for the surface strip foundation on a working platform modelled on a twolayered substrate is considered in the study.The upper layer is assumed as man-made and wellcontrolled and thus non-variable.The lower layer modelling natural cohesive soil is subjected to spatial variability of undrained shear strength.The random failure mechanism method(RFMM)is used to evaluate the bearing capacity.This approach employs a kinematic assessment of the critical load and incorporates the averaging of three-dimensional(3 D)random field along dissipation surfaces that result from the failure mechanism geometry.A novel version of the approach considering an additional linear trend of undrained shear strength in the spatially variable layer is proposed.The high efficiency of the RFMM algorithm is preserved.The influences of foundation length,trend slope in the spatially variable layer,fluctuation scales,and thickness of the homogenous sand layer on the resulting bearing capacity evaluations are analysed.Moreover,for selected cases,verification of the RFMM based assessment obtained using random finite difference method(RFDM)based on 3 D analysis is provided.Two types of analyses are performed using RFDM based on associated and non-associated flow rules.For associated flow rule which corresponds to RFMM,the RFMM is conservative and efficient and thus it seems preferable.However,if RFDM employs non-associated flow rule(much lower dilation angle for sand layer),the efficient RFMM is no longer conservative.For this situation,a combined approach that improves the efficiency of the numerical method is suggested.展开更多
Bearing the large moment that is generated by the wind load that acts on the upper structure of offshore wind turbines is an important feature of their foundations that is different from other offshore structures.A co...Bearing the large moment that is generated by the wind load that acts on the upper structure of offshore wind turbines is an important feature of their foundations that is different from other offshore structures.A composite bucket shallow foundation(CBSF)has been proposed by Tianjin University to address the soft geological conditions in the offshore regions of China for wind turbines.The CBSF is a new type of foundation and is effective against large moments.The soil deformation test of a CBSF and the numerical simulation study under the same working conditions are carried out to determine the failure mechanism of a CBSF under moment loading.The resisting soil compression rateηm is defined as a new empirical parameter that indicates the ability of the soil inside the bucket to resist moment loading.The upper limit of the resisting moment bearing capacity of the bucket foundation is derived through the upper bound theorem of classical plasticity theory based on the failure mechanism.The calculation method is validated by tests of bucket models with different height-diameter ratios in sand under moment loading.展开更多
The conventional pseudo-dynamic(CPD)and modified pseudo-dynamic(MPD)methods are invoked to obtain the seismic bearing capacity of strip foundations using the limit equilibrium method,with a two-wedge failure mechanism...The conventional pseudo-dynamic(CPD)and modified pseudo-dynamic(MPD)methods are invoked to obtain the seismic bearing capacity of strip foundations using the limit equilibrium method,with a two-wedge failure mechanism.A spectral version of the conventional pseudo-dynamic method(SPD)is also invoked by considering the ground motion amplification factor,to be a function of the non-dimensional frequencyλ/B and soil damping.Numeric analyses show that bearing capacity results obtained by the MPD and SPD methods are generally consistent.Both experience the same general reduction in bearing capacity with the increase ofλ/B,with successive ups and downs corresponding to soil′s natural frequencies.For 5<λ/B<10,SPD and MPD results fluctuated between falling above and below CPD results.Forλ/B<2.5,SPD and MPD results were consistent with attenuation of the shear wave,while for 10<λ/B,amplification was exhibited.Results obtained by the CPD method monotonically decrease,due to the fact that CPD fails to inherently consider site effects and damping,and instead and relies on a single factor to consider the ground motion amplification.展开更多
Much empiricism is involved in design of rock-socketed piles in rock masses.In light of this,an analytical solution based on the cavity expansion theory is proposed for calculating the ultimate bearing capacity at the...Much empiricism is involved in design of rock-socketed piles in rock masses.In light of this,an analytical solution based on the cavity expansion theory is proposed for calculating the ultimate bearing capacity at the tip of a pile embedded in rock masses obeying the Hoek-Brown failure criterion.The ultimate end bearing capacity is evaluated by assuming that the pressure exerted at the boundaries of a pressure bulb immediately beneath the pile tip is equal to the limit pressure required to expand a spherical cavity.In addition,a relationship is derived to predict the pile load-settlement response.To demonstrate the applicability of the presented solution,the results of this study were compared to those of 91 field tests from technical literature.Despite the limitations,it is found that the end bearing resistance computed by the present work is in good agreement with the field test results.展开更多
The present study proposes a novel and simplified methodology to assess the seismic bearing capacity(SBC) of a shallow strip footing by incorporating strength non-linearity arising due to partial saturation of a soil ...The present study proposes a novel and simplified methodology to assess the seismic bearing capacity(SBC) of a shallow strip footing by incorporating strength non-linearity arising due to partial saturation of a soil matrix. Furthermore, developed methodology incorporates the modal response analysis of soil layers to assess SBC. A constant matric suction distribution profile has been considered throughout the depth of the soil. The Van Genuchten equation and corresponding fitting parameters have been considered to quantify matric suction in the analysis. SBC has been obtained for three different geomaterials;viz. sand, fly ash and clay, based on their predominant grain size and diverse soil water characteristics curve(SWCC) attributes. Variation of SBC with different modes of vibration and damping ratio are reported for ranges of matric suction pertinent to the geomaterials considered in the study. The relative significance of matric suction on SBC has been reported for suction values within the transition zone of each geomaterial. It is observed that the SBC of sand is drastically reduced, with matric suction reaching beyond the residual suction value. The SBC of fly ash remains constant beyond the residual suction value, whereas the SBC of clay shows an increasing trend toward the practical range of matric suction values.展开更多
文摘The presence of waste tires poses an environmental challenge as they occupy a significant amount of land and are expensive to dispose in landfills.However,reusing waste tires can address this issue when waste tires are used in geotechnical applications.To determine the viability of this approach,laboratoryscale tests were conducted to investigate load-bearing capacity of circular footings on sand-tire shred(STS)mixtures with shredded waste tire contents of 5%e15%by weight and three different widths of shreds.The investigation focused on analyzing the thickness of layers composed of STS mixtures,the soil cap,and the impact of geogrids on bearing capacity.The results indicate that a specific mixture of sand and tire shreds provides the highest footing-bearing capacity.In addition,the optimal shred content and size were found to be 10%by weight and 2 cm×10 cm,respectively.Furthermore,for a given tire shred width,a particular length provides the largest bearing capacity.The results agree well with that of previous research conducted by the first author and his colleagues in direct shear and California bearing ratio(CBR)tests.The primary finding of this research is that the use of two-layered STS mixtures reinforced by geogrids significantly enhances the bearing capacity.
基金supported by the National Natural Science Foundation of China(51978345,52278264).
文摘A theoretical analysis of upward deflection and midspan deflection of prestressed bamboo-steel composite beams is presented in this study.The deflection analysis considers the influences of interface slippage and shear deformation.Furthermore,the calculation model for flexural capacity is proposed considering the two stages of loading.The theoretical results are verified with 8 specimens considering different prestressed load levels,load schemes,and prestress schemes.The results indicate that the proposed theoretical analysis provides a feasible prediction of the deflection and bearing capacity of bamboo-steel composite beams.For deflection analysis,the method considering the slippage and shear deformation provides better accuracy.The theoretical method for bearing capacity matches well with the test results,and the relative errors in the serviceability limit state and ultimate limit state are 4.95%and 5.85%,respectively,which meet the accuracy requirements of the engineered application.
文摘A bridge project is taken as an example to analyze the application of bearing capacity detection and evaluation.This article provides a basic overview of the project,the application of bearing capacity detection technology,and the bearing capacity assessment analysis.It is hoped that this analysis can provide a scientific reference for the load-bearing capacity detection and evaluation work in bridge engineering projects,thereby achieving a scientific assessment of the overall load-bearing capacity of the bridge engineering structure.
文摘The bearing capacity testing and evaluation of the existing bridge engineering structure is not only the key to clarify its structural quality and safety performance,but it also can lay a solid foundation for subsequent repairs and maintenance work.To ensure the bearing capacity,durability and reliability of existing bridges,this paper analyzes the importance and methods of testing and evaluation of structural bearing capacity of a bridge.This analysis aims to provide scientific reference for the quality assessment and subsequent repair and maintenance of existing bridge engineering structures.
基金This work was financially supported by the National Key Research and Development Program of China(No.2022YFC2903804)the National Natural Science Foundation of China(Nos.52004054,52274115,51874068 and 52074062).
文摘This paper aims to determine the load bearing capacity of pre-stressed expandable props with different geometries and load eccentricities for flexible support in underground mining or excavation.It is deduced that the expandable device could have much higher strength(>89 MPa)by laboratory tests,and the load bearing capacity of the expandable prop may depend on the stability of the supporting steel pipe structure.A good agreement was found between the laboratory test and numerical results in terms of the load bearing capacity and the final macro-bending failure pattern for expandable props with heights of 1.5 and 2.7 m,and the theoretical calculation for the strength of traditional steel structures is not directly suitable for the expandable props.Moreover,additional numerical simulations were performed for the expandable props with different normalized slenderness ratiosλ_(n)and loading eccentric distances e.The variation of stability coefficient of the expandable prop is in line with the Perry-Robertson equation and its correlation coefficients are fitted as a of 0.979 and b of 0.314.For estimating the load bearing capacity of the expandable props,the strength equation for traditional steel structures is improved by introducing a bending magnification factor and by modifying the normalized slenderness ratio to a converted slenderness ratio.Based on the underground field monitoring for the strength of expandable props with different heights,the empirical eccentric distances were back calculated,and a safety factor is introduced to obtain the designed strength of the expandable prop.In addition,a four-step design procedure is proposed for the expandable prop.
文摘This paper investigates the validity and shortcomings of the existing analytical solution for the ultimate bearing capacity of a pile embedded in a rock mass using the modified HoekeBrown failure criterion.Although this criterion is considered a reference value for empirical and numerical calculations,some limitations of its basic simplifications have not been clarified yet.This research compares the analytical results obtained from the novel discontinuity layout optimization(DLO)method and the numerical solutions from the finite difference method(FDM).The limitations of the analytical solution are considered by comparing different DLO failure modes,thus allowing for the first time a critical evaluation of its scope and conditioning for implementation.Errors of up to 40%in the bearing capacity and unrealistic failure modes are the main issues in the analytical solution.The main aspects of the DLO method are also analyzed with an emphasis on the linearization of the rock failure criterion and the accuracy resulting from the discretization size.The analysis demonstrates DLO as a very efficient and accurate tool to address the pile tip bearing capacity,presenting considerable advantages over other methods.
基金The work described in this paper is partially supported by the ARC Discovery Project(Grant Nos.DP210100437 and DP230100126)the National Natural Science Foundation of China(Grant No.41790445),for which the authors are very grateful.
文摘Slope bearing capacity is one of the most important characteristics in slope engineering and is strongly influenced by weak planes,loading conditions,and slope geometry.By presenting the evolution of slip surfaces,this paper explored how the slope bearing capacity is affected by widely observed influencing factors.The initiation and propagation of slip surfaces are presented in laboratory model tests of slope using the transparent soil technique.Shear band evolution under various weak planes,loading conditions,and slope geometries were experimentally presented,and slope bearing capacities were analyzed with the process of shear band evolution.This paper verified that slip surface morphologies have a strong relation with the slope bearing capacity.The same slip surface morphology can have different evolutionary processes.In this case,it is the shear band evolution that determines the slope bearing capacity,not the morphology of the slip surface.The influencing factors such as pre-existing weak planes,loading conditions,and slope geometry strongly affect the slope bearing capacity as these factors govern the process of shear band evolution inside the slope.
基金supported by Korea Research Fellowship Program through the National Research Foundation of Korea(NRF)funded by the Ministry of Science and ICT(Grant No.2019H1D3A1A01102993)the Inha University Research Grant(2022).
文摘Ultimate bearing capacity(UBC)is a key subject in geotechnical/foundation engineering as it determines the limit of loads imposed on the foundation.The most reliable means of determining UBC is through experiment,but it is costly and time-consuming which has led to the development of various models based on the simplified assumptions.The outcomes of the models are usually validated with the experimental results,but a large gap usually exists between them.Therefore,a model that can give a close prediction of the experimental results is imperative.This study proposes a grasshopper optimization algorithm(GOA)and salp swarm algorithm(SSA)to optimize artificial neural networks(ANNs)using the existing UBC experimental database.The performances of the proposed models are evaluated using various statistical indices.The obtained results are compared with the existing models.The proposed models outperformed the existing models.The proposed hybrid GOA-ANN and SSA-ANN models are then transformed into mathematical forms that can be incorporated into geotechnical/foundation engineering design codes for accurate UBC measurements.
文摘Artificial cementation is a method commonly used to enhance and improve soil properties. This paper investigates the effect of using different amounts of cement on soil strength parameters and soil bearing capacity, using the finite element method. Experimental tests are conducted on soil samples with different amounts of Portland cement. A 2-D numerical model is created and validated using the numerical modelling software, COMSOL Multiphysics 5.6 software. The study finds that the cohesion, and the angle of the internal friction of the soil samples increase significantly as a result of adding 1%, 2%, and 4% of Portland cement. The results demonstrate that the stresses and strain under the strip footing proposed decrease by 3.24% and 7.42%. Moreover, the maximum displacement also decreases by 1.47% and 2.97%, as a result of adding cements of 2% and 4%. The bearing capacity values obtained are therefore excellent, especially when using the 2% and 4% cement. The increase identified is due to the increased values of the bearing capacity factors. It is concluded that from an economic viewpoint, using 2% cement is the best option.
文摘This study addresses the pressing need to assess foundation bearing capacity in Opolo,Yenagoa,Bayelsa State,Nigeria.The significance lies in the dearth of comprehensive geotechnical data for construction planning in the region.Past research is limited and this study contributes valuable insights by integrating Geographic Information System(GIS)with the Generalized Reciprocal Method(GRM).To collect data,near-surface seismic refraction surveys were conducted along three designated lines,utilizing ABEM Terraloc Mark 6 equipment,Easy Refract,and ArcGIS 10.4.1 software.This methodology allowed for the determination of key geotechnical parameters essential for soil characterization at potential foundation sites.The results revealed three distinct geoseismic layers.The uppermost layer,within a depth of 0.89 to 1.50 meters,exhibited inadequate compressional and shear wave velocities and low values for oedometric modulus,shear modulus,N-value,ultimate bearing capacity,and allowable bearing capacity.This indicates the presence of unsuitable,soft,and weak alluvial deposits for substantial structural loads.In contrast,the second layer(1.52 to 3.84 m depth)displayed favorable geotechnical parameters,making it suitable for various construction loads.The third layer(15.00 to 26.05 m depth)exhibited varying characteristics.The GIS analysis highlighted the unsuitability of the uppermost layer for construction,while the second and third layers were found to be fairly competent and suitable for shallow footing and foundation design.In summary,this study highlights the importance of geotechnical surveys in Opolo’s construction planning.It offers vital information for informed choices,addresses issues in the initial layer,and suggests secure,sustainable construction options.
文摘The paper presents conclusions related to the design of shallow foundations,at the site where the Substation at Kashari,in Tirana is foreseen to be constructed.The project includes buildings with small to medium structures with 1-3 stories.The geological survey works include 6 boreholes of a depth 20.0 m,90 SPT(Standard Penetration Tests)tests,and laboratory works include 13 direct shear tests,27 unconfined and compressive strength tests,7 CU(consolidated undrained)tests and 9 UU(unconsolidated undrained)tests,etc.The foundation design must fulfill both,bearing and settlement criteria,but in this case the settlements of foundations are not possible to be calculated,since the laboratory works do not include any consolidation test.So,the local bearing capacity is expected to control the design in terms of bearing capacity and settlements.The local bearing capacity of shallow square foundations is evaluated by using Terzaghi’s formula,based on reduced shear strength parameters of soils below the bottom of foundations.The results are compared with the bearing capacity values calculated by using Burland and Burbdige(1984)method,based on the data of SPT tests.This method is used for checking the settlement(serviceability)criterion in the foundation design,when the direct settlement calculation is missing.The paper presents some conclusions related to local bearing capacity foundation-based design.
基金the National Key Research and Development Program(Grant No.2017YFC0703408)the National Natural Science Foundation of China(Grant Nos.51678145 and 51478160)the Natural Science Foundation of Jiangsu Province(Grant No.BK20180155).
文摘Suction caisson foundations are often subjected to vertical uplift loads,but there are still no wide and spread engineering specifications on design and calculation method for uplift bearing capacity of suction caisson foundation.So it is important to establish an uplift failure criterion.In order to study the uplift bearing mechanism and failure mode of suction caisson foundation,a series of model tests were carried out considering the effects of aspect ratio,soil permeability and loading mode.Test results indicate that the residual negative pressure at the top of caisson is beneficial to enhance uplift bearing capacity.The smaller the permeability coefficient is,the higher the residual negative pressure will be.And the residual negative pressure is approximately equal to the water head that causes seepage in the caisson.When the load reaches the ultimate bearing capacity,both the top and bottom negative pressures are smaller than Su and both the top and bottom reverse bearing capacity factors are smaller than 1.0 in soft clay.Combined the uplift bearing characteristics of caisson in sandy soil and soft clay,the bearing capacity composition and the calculation method are proposed.It can provide a reference for the engineering design of suction caisson foundation under vertical load.
基金The authors wish to thank the support from the‘Double Tops’Construction Independent Innovation Project of China University of Mining and Technology(Grant No.2018ZZCX04).
文摘Low gravity fields have been simulated through magnetic acceleration to conduct experimental study on bearing capacity of circular footings on a type of crushable planetary regolith simulant,which has comparable density and particle size distribution of lunar soil.The loadesettlement responses of surface spread footings are obtained by investigating the relative density,footing size and gravity effects.Applying the hyperbolic asymptote method,normalised foundation stiffness and ultimate bearing capacity are obtained by curve fitting and predicted by power functions using multivariate nonlinear regression.The results show that the nonlinear gravity effect is not negligible,related to stress condition,soil dilatancy and mobilised friction angle.A cone penetration test(CPT)-based method for prediction of bearing capacity is proposed with correlations between ultimate bearing capacity of footings and shallow penetration stiffness of CPTs,avoiding the uncertainties of soil property estimations.Analyses of allowable bearing capacity and footing influence zone in consideration of footing size and gravity effects could therefore improve the design of shallow foundations on the Moon and Mars,and provide new understandings and potential implications to the bearing capacity of shallow foundations on crushable granular material in both terrestrial and extraterrestrial geotechnical engineering.
基金This research was financially supported by the National Science Fund for Distinguished Young Scholars(Grant No.51825904)the National Science and Technology Major Project from the Ministry of Science and Technology(MOST)of China(Grant No.2016ZX05058004-005).
文摘Reducing the cost of offshore platform construction is an urgent issue for marginal oilfield development.The offshore oil well structure includes a riser and a surface casing.The riser,surface casing and oil well cement can be considered special variable cross-section piles.Replacing or partially replacing the steel pipe pile foundation with a variable cross-section pile to provide the required bearing capacity for an offshore oil platform can reduce the cost of foundation construction and improve the economic efficiency of production.In this paper,the finite element analysis method is used to investigate the variable cross-section bearing mode of composite piles composed of a riser and a surface casing in saturated clay under a vertical load.The calculation formula of the bearing capacity at the variable section is derived based on the theory of spherical cavity expansion,the influencing factors of the bearing capacity coefficient N_(c) are revealed,and the calculation method of N_(c) is proposed.By comparing the calculation results with the results of the centrifuge test,the accuracy and applicability of the calculation method are verified.The results show that the riser composite pile has a rigid core in the soil under the variable cross-section,which increases the bearing capacity at the variable cross-section.
基金financially supported by the National Key Research and Development Program(Grant No.2017YFC0703408)the National Natural Science Foundation of China(Grant Nos.51678145 and 51878160)
文摘Suction caisson foundation derives most of their uplift resistance from passive suction developed during the pullout movement. It was observed that the passive suction generated in soil at the bottom of the caisson and the failure mode of suction caisson foundation subjecting pullout loading behaves as a reverse compression failure mechanism.The upper bound theorems have been proved to be a powerful method to find the critical failure mechanism and critical load associated with foundations, buried caissons and other geotechnical structures. However, limited attempts have been reported to estimate the uplift bearing capacity of the suction caisson foundation using the upper bound solution. In this paper, both reverse failure mechanisms from Prandtl and Hill were adopted as the failure mechanisms for the computation of the uplift bearing capacity of the suction caisson. New equations were proposed based on both failure mechanisms to estimate the pullout capacity of the suction caisson. The proposed equations were verified by the test results and experimental data from published literature. And the two solutions agree reasonably well with the other test results. It can be proved that both failure mechanisms are reasonably and more consistent with the actual force condition.
文摘A bearing capacity evaluation for the surface strip foundation on a working platform modelled on a twolayered substrate is considered in the study.The upper layer is assumed as man-made and wellcontrolled and thus non-variable.The lower layer modelling natural cohesive soil is subjected to spatial variability of undrained shear strength.The random failure mechanism method(RFMM)is used to evaluate the bearing capacity.This approach employs a kinematic assessment of the critical load and incorporates the averaging of three-dimensional(3 D)random field along dissipation surfaces that result from the failure mechanism geometry.A novel version of the approach considering an additional linear trend of undrained shear strength in the spatially variable layer is proposed.The high efficiency of the RFMM algorithm is preserved.The influences of foundation length,trend slope in the spatially variable layer,fluctuation scales,and thickness of the homogenous sand layer on the resulting bearing capacity evaluations are analysed.Moreover,for selected cases,verification of the RFMM based assessment obtained using random finite difference method(RFDM)based on 3 D analysis is provided.Two types of analyses are performed using RFDM based on associated and non-associated flow rules.For associated flow rule which corresponds to RFMM,the RFMM is conservative and efficient and thus it seems preferable.However,if RFDM employs non-associated flow rule(much lower dilation angle for sand layer),the efficient RFMM is no longer conservative.For this situation,a combined approach that improves the efficiency of the numerical method is suggested.
基金supported by the National Natural Science Foundation of China(Grant Nos.51709199 and 51322904).
文摘Bearing the large moment that is generated by the wind load that acts on the upper structure of offshore wind turbines is an important feature of their foundations that is different from other offshore structures.A composite bucket shallow foundation(CBSF)has been proposed by Tianjin University to address the soft geological conditions in the offshore regions of China for wind turbines.The CBSF is a new type of foundation and is effective against large moments.The soil deformation test of a CBSF and the numerical simulation study under the same working conditions are carried out to determine the failure mechanism of a CBSF under moment loading.The resisting soil compression rateηm is defined as a new empirical parameter that indicates the ability of the soil inside the bucket to resist moment loading.The upper limit of the resisting moment bearing capacity of the bucket foundation is derived through the upper bound theorem of classical plasticity theory based on the failure mechanism.The calculation method is validated by tests of bucket models with different height-diameter ratios in sand under moment loading.
文摘The conventional pseudo-dynamic(CPD)and modified pseudo-dynamic(MPD)methods are invoked to obtain the seismic bearing capacity of strip foundations using the limit equilibrium method,with a two-wedge failure mechanism.A spectral version of the conventional pseudo-dynamic method(SPD)is also invoked by considering the ground motion amplification factor,to be a function of the non-dimensional frequencyλ/B and soil damping.Numeric analyses show that bearing capacity results obtained by the MPD and SPD methods are generally consistent.Both experience the same general reduction in bearing capacity with the increase ofλ/B,with successive ups and downs corresponding to soil′s natural frequencies.For 5<λ/B<10,SPD and MPD results fluctuated between falling above and below CPD results.Forλ/B<2.5,SPD and MPD results were consistent with attenuation of the shear wave,while for 10<λ/B,amplification was exhibited.Results obtained by the CPD method monotonically decrease,due to the fact that CPD fails to inherently consider site effects and damping,and instead and relies on a single factor to consider the ground motion amplification.
文摘Much empiricism is involved in design of rock-socketed piles in rock masses.In light of this,an analytical solution based on the cavity expansion theory is proposed for calculating the ultimate bearing capacity at the tip of a pile embedded in rock masses obeying the Hoek-Brown failure criterion.The ultimate end bearing capacity is evaluated by assuming that the pressure exerted at the boundaries of a pressure bulb immediately beneath the pile tip is equal to the limit pressure required to expand a spherical cavity.In addition,a relationship is derived to predict the pile load-settlement response.To demonstrate the applicability of the presented solution,the results of this study were compared to those of 91 field tests from technical literature.Despite the limitations,it is found that the end bearing resistance computed by the present work is in good agreement with the field test results.
文摘The present study proposes a novel and simplified methodology to assess the seismic bearing capacity(SBC) of a shallow strip footing by incorporating strength non-linearity arising due to partial saturation of a soil matrix. Furthermore, developed methodology incorporates the modal response analysis of soil layers to assess SBC. A constant matric suction distribution profile has been considered throughout the depth of the soil. The Van Genuchten equation and corresponding fitting parameters have been considered to quantify matric suction in the analysis. SBC has been obtained for three different geomaterials;viz. sand, fly ash and clay, based on their predominant grain size and diverse soil water characteristics curve(SWCC) attributes. Variation of SBC with different modes of vibration and damping ratio are reported for ranges of matric suction pertinent to the geomaterials considered in the study. The relative significance of matric suction on SBC has been reported for suction values within the transition zone of each geomaterial. It is observed that the SBC of sand is drastically reduced, with matric suction reaching beyond the residual suction value. The SBC of fly ash remains constant beyond the residual suction value, whereas the SBC of clay shows an increasing trend toward the practical range of matric suction values.