Studies on ultrafine particle catalyst have attracted many researchers' attention by its large surface area,higher activity and selectivity.Based on the mechanism of α-Fe and Fe_xC_y as the catalytical active spe...Studies on ultrafine particle catalyst have attracted many researchers' attention by its large surface area,higher activity and selectivity.Based on the mechanism of α-Fe and Fe_xC_y as the catalytical active species this paper reports for the first time the preparation method of Fe_3C ultrafine parti- cle catalyst,from highly dispersed amorphous Fe powder and free carbon.The Fe powder and free car- bon,prepared by laser pyrolysis technique,was then treated by washing and heating at high tempera- ture protected with N_2.The catalyst prepared under different experimental conditions was characterazed by means of XRD,electronic diffraction and TEM.It shows that the crystlline grain size is in a range of 1-4nm and composed of Fe_3C and α-Fe.It has been found that the ultrafine particle iron-carbonide catalyst exhibited much higher activity and selectivity to light olefins.At the standard atmosphere and 380℃ reaction temperature,the conversion of CO reached a maximum of 80%.展开更多
The stress–strain behavior and strain rate sensitivity of pre-strained Ni80Cr20（Ni20Cr） were studied at strain rates from 4.8×10^（–4）s^（–1） to 1.1×10^（–1）s^（–1）. Specimens were prepared throug...The stress–strain behavior and strain rate sensitivity of pre-strained Ni80Cr20（Ni20Cr） were studied at strain rates from 4.8×10^（–4）s^（–1） to 1.1×10^（–1）s^（–1）. Specimens were prepared through cold drawing with abnormal plastic deformation. The texture of the specimen was characterized using electron backscatter diffraction. Results revealed that the ultimate tensile strength and ductility of the pre-strained Ni20Cr microwires simultaneously increased with increasing strain rate. Twinning-induced negative strain rate sensitivity was discovered. Positive strain rate sensitivity was present in fracture flow stress, whereas negative strain rate sensitivity was detected in flow stress values of σ_（0.5%） and σ_（1%）. Tensile test of the pre-strained Ni20Cr showed that twinning deformation predominated, whereas dislocation slip deformation dominated when twinning deformation reached saturation. The trends observed in the fractions of 2°-5°, 5°-15°, and 15°-180° grain boundaries confirmed that twinning deformation dominated the first stage.展开更多
基金The project was supported by the National Natural Science Foundation of China.
文摘Studies on ultrafine particle catalyst have attracted many researchers' attention by its large surface area,higher activity and selectivity.Based on the mechanism of α-Fe and Fe_xC_y as the catalytical active species this paper reports for the first time the preparation method of Fe_3C ultrafine parti- cle catalyst,from highly dispersed amorphous Fe powder and free carbon.The Fe powder and free car- bon,prepared by laser pyrolysis technique,was then treated by washing and heating at high tempera- ture protected with N_2.The catalyst prepared under different experimental conditions was characterazed by means of XRD,electronic diffraction and TEM.It shows that the crystlline grain size is in a range of 1-4nm and composed of Fe_3C and α-Fe.It has been found that the ultrafine particle iron-carbonide catalyst exhibited much higher activity and selectivity to light olefins.At the standard atmosphere and 380℃ reaction temperature,the conversion of CO reached a maximum of 80%.
基金Funded by the National Natural Science Foundation of China(No.11135007)
文摘The stress–strain behavior and strain rate sensitivity of pre-strained Ni80Cr20（Ni20Cr） were studied at strain rates from 4.8×10^（–4）s^（–1） to 1.1×10^（–1）s^（–1）. Specimens were prepared through cold drawing with abnormal plastic deformation. The texture of the specimen was characterized using electron backscatter diffraction. Results revealed that the ultimate tensile strength and ductility of the pre-strained Ni20Cr microwires simultaneously increased with increasing strain rate. Twinning-induced negative strain rate sensitivity was discovered. Positive strain rate sensitivity was present in fracture flow stress, whereas negative strain rate sensitivity was detected in flow stress values of σ_（0.5%） and σ_（1%）. Tensile test of the pre-strained Ni20Cr showed that twinning deformation predominated, whereas dislocation slip deformation dominated when twinning deformation reached saturation. The trends observed in the fractions of 2°-5°, 5°-15°, and 15°-180° grain boundaries confirmed that twinning deformation dominated the first stage.
