逐次逼近寄存器模数转换器(SAR ADC)在逐次逼近的过程中,电容的切换会使参考电压上出现参考纹波噪声,该噪声会影响比较器的判定,进而输出错误的比较结果。针对该问题,基于CMOS 0.5μm工艺,设计了一种具有纹波消除技术的10 bit SAR ADC...逐次逼近寄存器模数转换器(SAR ADC)在逐次逼近的过程中,电容的切换会使参考电压上出现参考纹波噪声,该噪声会影响比较器的判定,进而输出错误的比较结果。针对该问题,基于CMOS 0.5μm工艺,设计了一种具有纹波消除技术的10 bit SAR ADC。通过增加纹波至比较器输入端的额外路径,将参考纹波满摆幅输入至比较器中;同时设计了消除数模转换器(DAC)模块,对参考纹波进行采样和输入,通过反转纹波噪声的极性,消除参考纹波对ADC输出的影响。该设计将信噪比(SNR)提高到56.75 dB,将有效位数(ENOB)提升到9.14 bit,将积分非线性(INL)从-1~5 LSB降低到-0.2~0.3 LSB,将微分非线性(DNL)从-3~4 LSB降低到-0.5~0.5 LSB。展开更多
Bit Error Probability (BEP) provides a fundamental performance measure for wireless diversity systems. This paper presents two new exact BEP expressions for Maximal Ratio Combining (MRC) diversity systems. One BEP exp...Bit Error Probability (BEP) provides a fundamental performance measure for wireless diversity systems. This paper presents two new exact BEP expressions for Maximal Ratio Combining (MRC) diversity systems. One BEP expression takes a closed form, while the other is derived by treating the squared-sum of Rayleigh random variables as an Erlang variable. Due to the fact that the extant bounds are loose and could not properly characterize the error performance of MRC diversity systems, this paper presents a very tight bound. The numerical analysis shows that the new derived BEP expressions coincide with the extant expressions, and that the new approximation tightly bounds the accurate BEP.展开更多
针对正交频分复用(Orthogonal Frequency Division Multiplexing,OFDM)系统中最小均方误差(Minimum Mean Squared Error,MMSE)信道估计算法误码率(BER)高的问题,提出一种平均最小均方误差(Averaged-Minimum Mean Squared Error,A-MMSE)...针对正交频分复用(Orthogonal Frequency Division Multiplexing,OFDM)系统中最小均方误差(Minimum Mean Squared Error,MMSE)信道估计算法误码率(BER)高的问题,提出一种平均最小均方误差(Averaged-Minimum Mean Squared Error,A-MMSE)信道估计算法。该算法首先基于802.11n标准而构造了一种新的导频结构,收发两端分别进行降采样和过采样处理,利用已知训练序列和导频获得信道频域响应。仿真结果表明,所提出的A-MMSE信道估计算法与传统的MMSE算法相比,在BER为10^(-3)时,信噪比改善了约8dB。因而所提出的信道估计算法能明显改善系统的BER性能。展开更多
为降低电磁干扰对信号传输的影响,分析了应答器上行链路信号传输过程及其易遭受干扰信号的特点,设计了基于符号最小均方误差(least mean square,LMS)算法的自适应解调方法。为在硬件平台中实现该解调方法,通过仿真计算,确定LMS算法的自...为降低电磁干扰对信号传输的影响,分析了应答器上行链路信号传输过程及其易遭受干扰信号的特点,设计了基于符号最小均方误差(least mean square,LMS)算法的自适应解调方法。为在硬件平台中实现该解调方法,通过仿真计算,确定LMS算法的自适应算法中间变量变化范围,使用截位操作完成权值系数的更新,设置均衡器长度、步长因子、中值滤波系数分别为1、1/64、16,可在不占用过多硬件资源情况下获得良好的解调性能。解调算法在现场可编程门阵列(field programmable gata array,FPGA)上予以验证,实验表明,当信噪比为6 dB时,FPGA中自适应解调误码率为0.000001,在信噪比大于等于6 dB时,实测误码率与仿真分析误码率基本一致;FPGA自适应解调方法在列车不同速度等级下误码率均小于10^(-6)。展开更多
The theoretical lower bounds on mean squared channel estimation errors for typical fading channels are presented by the infinite-length and non-causal Wiener filter and the exact closed-form expressions of the lower b...The theoretical lower bounds on mean squared channel estimation errors for typical fading channels are presented by the infinite-length and non-causal Wiener filter and the exact closed-form expressions of the lower bounds for different channel Doppler spectra are derived. Based on the obtained lower bounds on mean squared channel estimation errors, the limits on bit error rate （BER） for maximal ratio combining （MRC） with Gaussian distributed weighting errors on independent and identically distributed （i. i. d） fading channels are presented. Numerical results show that the BER performances of ideal MRC are the lower bounds on the BER performances of non-ideal MRC and deteriorate as the maximum Doppler frequency increases or the SNR of channel estimate decreases.展开更多
In today’s rapidly evolving landscape of communication technologies,ensuring the secure delivery of sensitive data has become an essential priority.To overcome these difficulties,different steganography and data encr...In today’s rapidly evolving landscape of communication technologies,ensuring the secure delivery of sensitive data has become an essential priority.To overcome these difficulties,different steganography and data encryption methods have been proposed by researchers to secure communications.Most of the proposed steganography techniques achieve higher embedding capacities without compromising visual imperceptibility using LSB substitution.In this work,we have an approach that utilizes a combinationofMost SignificantBit(MSB)matching andLeast Significant Bit(LSB)substitution.The proposed algorithm divides confidential messages into pairs of bits and connects them with the MSBs of individual pixels using pair matching,enabling the storage of 6 bits in one pixel by modifying a maximum of three bits.The proposed technique is evaluated using embedding capacity and Peak Signal-to-Noise Ratio(PSNR)score,we compared our work with the Zakariya scheme the results showed a significant increase in data concealment capacity.The achieved results of ourwork showthat our algorithmdemonstrates an improvement in hiding capacity from11%to 22%for different data samples while maintaining a minimumPeak Signal-to-Noise Ratio(PSNR)of 37 dB.These findings highlight the effectiveness and trustworthiness of the proposed algorithm in securing the communication process and maintaining visual integrity.展开更多
An experimental study of rock-breaking with an offset single cone bit was completed on the bit bench test equipment. Data such as transmission ratio, weight on bit （WOB）, rate of penetration （ROP） and torque on bi...An experimental study of rock-breaking with an offset single cone bit was completed on the bit bench test equipment. Data such as transmission ratio, weight on bit （WOB）, rate of penetration （ROP） and torque on bit were acquired in the experiments. Based on analyzing the experimental results, several conclusions were drawn as follows. The transmission ratio of the offset single-cone bit changed slightly with rotary speed of bit, weight on bit and offset distance. The rate of penetration of the offset singlecone bit increased with increase of WOB and off＇set distance. The torque on bit increased with increase of offset distance under the same WOB and bit rotary speed, decreased with increase of bit rotary speed under the same WOB. The rock-breaking mechanism of the offset single-cone bit was a scraping action. This indicates that the offset single-cone bit is a chipping type bit.展开更多
It is difficult to determine the optimal weight on bit (WOB) of the double-driven bottomhole assembly (DD-BHA, with double stabilizers and a bent housing positive displacement motor (PDM)) which is employed during ver...It is difficult to determine the optimal weight on bit (WOB) of the double-driven bottomhole assembly (DD-BHA, with double stabilizers and a bent housing positive displacement motor (PDM)) which is employed during vertical and fast drilling. High WOB leads to well deviation out of control, and low WOB leads to low rate of penetration (ROP). So considering the rock physical properties, the anisotropy index function of polycrystalline diamond compact (PDC) bit was derived with the structure and cutting performance parameters of the bit, and the effect of natural hole deviation tendencies on the performance of DD-BHA resisting deviation was represented. The concept of elliptic deformation ratio was used to characterize the performance of DD-BHA resisting deviation. Eventually, a model calculating the critical WOB was established. By comparing the model predictions with the measured hole angle changes in the field, the results show that the model predictions are accurate with error less than 5.8%, which can meet the operational requirements in the projects. Furthermore, the model was adopted to justify and guide the operating conditions and parameters during drilling, which shows that the optimum WOB predicted by the model can not only control deviation but also improve ROP effectively. The model is independent on the formation characteristics of blocks, so it can be expanded widely to other oilfields.展开更多
A new tracking algorithm is proposed aiming at the tracking problem in low bit signal-to- noise ratio （i. e. , Eb/N0 ） scenarios, in which the bit clock regenerated by bit synchronization loop decides loop update mo...A new tracking algorithm is proposed aiming at the tracking problem in low bit signal-to- noise ratio （i. e. , Eb/N0 ） scenarios, in which the bit clock regenerated by bit synchronization loop decides loop update moment. The double frequency processing and non-coherent accumulation tech- nologies are applied to eliminate the impact of data polarity inversion, and then long time accumula- tion improves the input signal-to-noise ratio of discriminator. The frequency locked loop and phase locked loop constitute a carrier loop in parallel, which can meet the high dynamic demands. The ef- fectiveness of this algorithm has been corroborated by theoretical analysis, simulation and measure- ments, and the new tracking algorithm has been used in an aerospace engineering project successfully.展开更多
基金Supported by the National Natural Science Foundation of China (No.60572059)Foundation of Guangdong Province for Ph.D. (No. 5300707).
文摘Bit Error Probability (BEP) provides a fundamental performance measure for wireless diversity systems. This paper presents two new exact BEP expressions for Maximal Ratio Combining (MRC) diversity systems. One BEP expression takes a closed form, while the other is derived by treating the squared-sum of Rayleigh random variables as an Erlang variable. Due to the fact that the extant bounds are loose and could not properly characterize the error performance of MRC diversity systems, this paper presents a very tight bound. The numerical analysis shows that the new derived BEP expressions coincide with the extant expressions, and that the new approximation tightly bounds the accurate BEP.
文摘针对正交频分复用(Orthogonal Frequency Division Multiplexing,OFDM)系统中最小均方误差(Minimum Mean Squared Error,MMSE)信道估计算法误码率(BER)高的问题,提出一种平均最小均方误差(Averaged-Minimum Mean Squared Error,A-MMSE)信道估计算法。该算法首先基于802.11n标准而构造了一种新的导频结构,收发两端分别进行降采样和过采样处理,利用已知训练序列和导频获得信道频域响应。仿真结果表明,所提出的A-MMSE信道估计算法与传统的MMSE算法相比,在BER为10^(-3)时,信噪比改善了约8dB。因而所提出的信道估计算法能明显改善系统的BER性能。
文摘The theoretical lower bounds on mean squared channel estimation errors for typical fading channels are presented by the infinite-length and non-causal Wiener filter and the exact closed-form expressions of the lower bounds for different channel Doppler spectra are derived. Based on the obtained lower bounds on mean squared channel estimation errors, the limits on bit error rate （BER） for maximal ratio combining （MRC） with Gaussian distributed weighting errors on independent and identically distributed （i. i. d） fading channels are presented. Numerical results show that the BER performances of ideal MRC are the lower bounds on the BER performances of non-ideal MRC and deteriorate as the maximum Doppler frequency increases or the SNR of channel estimate decreases.
基金in part by the Basic Science Research Program through the National Research Foundation of Korea(NRF)funded by the Ministry of Education(NRF-2021R1A6A1A03039493)by the 2024 Yeungnam University Research Grant.
文摘In today’s rapidly evolving landscape of communication technologies,ensuring the secure delivery of sensitive data has become an essential priority.To overcome these difficulties,different steganography and data encryption methods have been proposed by researchers to secure communications.Most of the proposed steganography techniques achieve higher embedding capacities without compromising visual imperceptibility using LSB substitution.In this work,we have an approach that utilizes a combinationofMost SignificantBit(MSB)matching andLeast Significant Bit(LSB)substitution.The proposed algorithm divides confidential messages into pairs of bits and connects them with the MSBs of individual pixels using pair matching,enabling the storage of 6 bits in one pixel by modifying a maximum of three bits.The proposed technique is evaluated using embedding capacity and Peak Signal-to-Noise Ratio(PSNR)score,we compared our work with the Zakariya scheme the results showed a significant increase in data concealment capacity.The achieved results of ourwork showthat our algorithmdemonstrates an improvement in hiding capacity from11%to 22%for different data samples while maintaining a minimumPeak Signal-to-Noise Ratio(PSNR)of 37 dB.These findings highlight the effectiveness and trustworthiness of the proposed algorithm in securing the communication process and maintaining visual integrity.
文摘An experimental study of rock-breaking with an offset single cone bit was completed on the bit bench test equipment. Data such as transmission ratio, weight on bit （WOB）, rate of penetration （ROP） and torque on bit were acquired in the experiments. Based on analyzing the experimental results, several conclusions were drawn as follows. The transmission ratio of the offset single-cone bit changed slightly with rotary speed of bit, weight on bit and offset distance. The rate of penetration of the offset singlecone bit increased with increase of WOB and off＇set distance. The torque on bit increased with increase of offset distance under the same WOB and bit rotary speed, decreased with increase of bit rotary speed under the same WOB. The rock-breaking mechanism of the offset single-cone bit was a scraping action. This indicates that the offset single-cone bit is a chipping type bit.
基金Projects(50804040,51004082)supported by the National Natural Science Foundation of China
文摘It is difficult to determine the optimal weight on bit (WOB) of the double-driven bottomhole assembly (DD-BHA, with double stabilizers and a bent housing positive displacement motor (PDM)) which is employed during vertical and fast drilling. High WOB leads to well deviation out of control, and low WOB leads to low rate of penetration (ROP). So considering the rock physical properties, the anisotropy index function of polycrystalline diamond compact (PDC) bit was derived with the structure and cutting performance parameters of the bit, and the effect of natural hole deviation tendencies on the performance of DD-BHA resisting deviation was represented. The concept of elliptic deformation ratio was used to characterize the performance of DD-BHA resisting deviation. Eventually, a model calculating the critical WOB was established. By comparing the model predictions with the measured hole angle changes in the field, the results show that the model predictions are accurate with error less than 5.8%, which can meet the operational requirements in the projects. Furthermore, the model was adopted to justify and guide the operating conditions and parameters during drilling, which shows that the optimum WOB predicted by the model can not only control deviation but also improve ROP effectively. The model is independent on the formation characteristics of blocks, so it can be expanded widely to other oilfields.
基金Supported by the National High Technology Research and Development Program of China(863 Program)(2011AA1569)
文摘A new tracking algorithm is proposed aiming at the tracking problem in low bit signal-to- noise ratio （i. e. , Eb/N0 ） scenarios, in which the bit clock regenerated by bit synchronization loop decides loop update moment. The double frequency processing and non-coherent accumulation tech- nologies are applied to eliminate the impact of data polarity inversion, and then long time accumula- tion improves the input signal-to-noise ratio of discriminator. The frequency locked loop and phase locked loop constitute a carrier loop in parallel, which can meet the high dynamic demands. The ef- fectiveness of this algorithm has been corroborated by theoretical analysis, simulation and measure- ments, and the new tracking algorithm has been used in an aerospace engineering project successfully.
