Monitoring Method for Blast Furnace Wall With Copper Staves

A monitoring method that has been designed for the first time for blast furnace wall with copper staves manufactured in China was introduced. Combining the method of ＂inverse problem＂ and the concept ＂non-inverse problem＂, the monitoring program for blast furnace wall with copper staves has been realized, which can be used to calculate online the accretion thickness and temperature of hot surface of copper staves after obtaining the values of thermocouples of copper staves. The accretion state obtained in the actual investigation has proved that the result of the program is correct. The monitoring program shows that the accretion would easily fluctuate when the accretion layer is extremely thick or thin, thereby the stable and smooth operation of the blast furnace is hindered. By maintaining appropriate accretion thickness, both long campaigns and high productivity of the blast furnace can be achieved; furthermore, it can also optimize the operation of blast furnace and maximize its production. Approximately 30--50 mm in thickness of accretion layer is maintained on the wall of Shougang blast furnace 2, which can meet the requirement for obtaining both long campaign and high productivity.

Analysis of temperature,stress,and displacement distributions of staves for a blast furnace

The temperature of gas flow inside a blast furnace （BF） changes significantly when the blast furnace is under unstable operations, and the temperature and stress distributions of cooling staves （CS） for BF work the same pattern. The effect of gas temperature on the temperature, stress, and displacement distributions of the cooling stave were analyzed as the gas temperature inside the blast furnace rose from 1000 to 1600℃ in 900 s. The results show that both the temperature and temperature gradient of the hot side of CS increase when the gas flow temperature inside BF rises. The temperature gradient of the hot side of CS is greater than that of the other area of CS and it can reach 65℃/mm. In the vertical direction of the hot side of CS, closer to the central part of CS, the stress intensity is greater than that of the other area of the hot side of CS, which causes cracks on the hot side of CS in the vertical di- rection. As the gas temperature increases, the stress intensity rate near the fixed pin increases and finally reaches 45 MPa/s. Fatigues near the fixed pin and bolts are caused by great stress intensity rate and the area around the pin can be damaged easily. The edge of CS bends toward the cold side and the central part of CS shifts toward the hot surface.

Quantificational indexes for design and evaluation of copper staves for blast furnaces

The quantificational and normative design is the precondition of improving the design of copper staves for blast furnaces. Based on a 3-dimensional temperature field calculation model, from the view point of heat transfer and long campaigns note with the core of forming accretion, the forming-accretion-ability （FAA） and the rib hot surface maximum temperature difference （ATmax） as quantificational indexes to direct and evaluate the design of copper staves for blast furnaces were presented. The application of the two indexes in design essentially embodies the new long campaigns in the stage of design. With the application of the two indexes, good results can be obtained. Firstly, it was suggested that the rib height of a copper stave can be reduced to 15 mm, which is a new method and theory for the reduction of copper staves. Secondly, the influence of insert on FAA and ATmax, is decided by the volume of insert. According to this, the principle of design for the hot surface geometry of copper staves was put forward that the ratio of the rib hot surface to the copper stave hot surface （abbreviated as the ratio of rib to stave） must be maintained in the range of 45% to 55%; for the present copper stave with a 35-40 mm thick rib, the ratio of rib to stave in the range of 50% to 55% can optimize the design of copper staves; for the copper stave with a smaller rib thickness, for example 15 ram, the ratio of rib to stave in the range of 45% to 50% can optimize the design of copper staves. It can be summarized that the thicker the rib thickness, the larger is the ratio of rib to stave. 2008 University of Science and Technology Beijing. All rights reserved.

Designing for Long Campaign Life Blast Furnace (2)-The Simulation of Temperature Field of Lining and Cooling Apparatus

Through the numerical modeling of temperature field for Blast Furnace (BF) lining and stave coolers, it can tell designers how to design a cooler which the hot surface temperature is less than its critical temperature under very high heat flux. Applying low heat re- sistance lining and staves cooler to BF is good for a layer of slag skull frozen on the hot surface of cooling stave. As long as the slag skull can stand, the furnace wall is stable and the heat loss of furnace does not increase. This is the basic principle for designing long campa- ignship BF.

Effect of cooling rate on the crystallization behavior of perovskite in high titanium-bearing blast furnace slag

The effect of cooling rate on the crystallization of perovskite in high Ti-bearing blast furnace（BF） slag was studied using confocal scanning laser microscopy（CSLM）. Results showed that perovskite was the primary phase formed during the cooling of slag. On the slag surface, the growth of perovskite proceeded via the successive production of quasi-particles along straight lines, which further extended in certain directions. The morphology and structure of perovskite was found to vary as a function of cooling rate. At cooling rates of 10 and 30 K/min, the dendritic arms of perovskite crossed obliquely, while they were orthogonal at a cooling rate of 20 K/min and hexagonal at cooling rates of 40 and 50 K/min. These three crystal morphologies thus obtained at different cooling rates respectively corresponded to the orthorhombic, cubic and hexagonal crystal structures of perovskite. The observed change in the structure of perovskite could probably be attributed to the deficiency of O^2-, when Ti2O3 was involved in the formation of perovskite.

New Type Regulating Valve Applied in Cooling System of Blast Furnace

A new type regulating valve with the cooling mode of constant temperature difference water supply, temperature difference self operated regulating valve, was introduced into blast furnace cooling system to overcome shortcomings of the cooling mode of constant flow rate water supply. The results show that the temperature difference between inlet and outlet water of cooling wall can be decreased greatly and steadily, and the water supply for blast furnace cooling can be reduced considerably.

Cooling Water Flow Rate Calculation for Hearth of Large Blast Furnaces

The cooling water flow rate for hearth of large blast furnaces was calculated by simulation. The results show that the cooling water flow rate shall be above 4 200m3/ h for hearth of large blast furnaces; to meet requirements of the increasing smelting intensity and to ensure the safety at the end of the first campaign,the designed maximum cooling water flow rate should be 5 900m3/ h; according to the flow distribution stability and the calculated resistance loss,hearth cooling stave pipes with the specification of 76 mm × 6 mm shall be adopted to assure the flow velocity in pipes of hearth cooling stave in the range of 1. 9- 2. 3 m / s.

Numerical simulation for the lower shaft and the hearth bottom of blast furnace

One of the methods forming the shell is to appropriately design the coolingstaves and hearth without overheating during the campaign life of the furnace. The three-dimensionalsteady mathematical models for calculating the temperature distribution in the coolers andtwo-dimensional unsteady mathematical models with phase-change latent heat for calculating thetemperature distribution of the hearth bottom were established. The calculation results show thatthe formation of the slag-metal protection shell can be achieved by optimizing the design parametersof the coolers. Increasing the heat conductivity of the carbon brick can move the isothermal lineof 1150 deg C upward outside the hearth bottom.

Physical Properties of Crushed Air-cooled Blast Furnace Slag and Numerical Representation of Its Morphology Characteristics

Physical properties and geometrical morphologies of crushed air-cooled blast furnace slag （SCR） and crushed limestone （LCR） were comparatively investigated. The shape, angularity, surface texture and internal pore structure of aggregate particles for different size and gradation were numerically represented by sphericity （ψ） and shape index （SI）, angularity number （AN）, index of aggregate particle shape and texture （IAPST）, porosity and pore size, respectively. The results show that SCR is a porous and rough aggregate. Apparent density, void, water absorption and smashing index of SCR are obviously higher than those of LCR with the same gradation, respectively. However, bulk density of SCR is lower than that of LCR with the same gradation. SI, AN, IAPST and porosity of SCR are obviously higher than those of LCR with the same gradation, respectively. The smaller particle size of SCR, the larger of its AN, IAPST and porosity.

Application of Air-cooled Blast Furnace Slag Aggregates as Replacement of Natural Aggregates in Cement-based Materials：A Study on Water Absorption Property

The influence of air-cooled blast furnace slag aggregates as replacement of natural aggregates on the water absorption of concrete and mortar was studied, and the mechanism was analyzed. The interface between aggregate and matrix in concrete was analyzed by using a micro-hardness tester, a laser confocal microscope and a scanning electron microscope with backscattered electron image mode. The pore structure of mortar matrixes under different curing conditions was investigated by mercury intrusion porosimetry. The results showed that when natural aggregates were replaced with air-cooled blast furnace slag aggregates in mortar or concrete, the content of the capillary pore in the mortar matrix was reduced and the interfacial structure between aggregate and matrix was improved, resulting in the lower water absorption of mortar or concrete. Compared to the concrete made with crushed limestone and natural river sand, the initial absorption coefficient, the secondary absorption coefficient and the water absorption capacity through the surface for 7 d of the concrete made from crushed air-cooled blast furnace slag and air-cooled blast furnace slag sand were reduced by 48.9%, 52.8%, and 46.5%, respectively.

Effect of Crushed Air-cooled Blast Furnace Slag on Mechanical Properties of Concrete

Morphology characteristics of mix aggregates with crushed air-cooled blast furnace slag（SCR） and crushed limestone（LCR） with 5-20 mm and 20-40 mm gradation were represented by numerical parameters including angularity number（AN） and index of aggregate particle shape and texture（IAPST）.The effect of mix aggregates containing SCR on compressive strength and splitting tensile strength of concrete was investigated.Fracture characteristics of concrete,interfacial structure between aggregates and matrix were analyzed.The experimental results show that porous and rough SCR increases contact area with matrix in concrete,concave holes and micro-pores on the surface of SCR are filled by mortar and hydrated cement paste,which may increase interlocking and mechanical bond between aggregate and matrix in concrete.SCR can be used to produce a high-strength concrete with better mechanical properties than corresponding concrete made with LCR.The increase of AN and IAPST of aggregate may enhance mechanical properties of concrete.

Model of Forming-Accretion on Blast Furnace Copper Stave and Industrial Application

Copper staves have been equipped on nearly all of BF （blast furnaces） with volume over than 1000 m3 in China since their introduction from abroad about more than 10 years ago. Because of short application and lack of experience, phenomena of thickened or naked of copper stave happen occasionally which influence production severely. So it is important to study the model of forming-accretion on BF copper stave and realize real-time monitoring of forming-accretion on different copper staves. Therefore, mathematic model of calculating accretion thickness by heat flow of BF is proposed, and the calculated results indicate that accretion thickness could be kept at a reasonable range of around 50 mm by controlling heat flux around 22.0 kW/mz. The monitoring program based on the model was applied to a certain BF in China successfully, and it is found that slip of BF near the inner wall is one of most important reasons that cause fluctuation of accretion thickness. During the period of scheduled maintenance of the certain BF, the thickness of accretion measured through the static pressure holes is in good accordance with the value calculated by the monitoring program, so the results calculated by the monitoring program can be used to guide industrial production

Cooling phenomena in blast furnace hearth

Cooling water provides the best protection for refractory in the blast furnace hearth. Stable and suitable water quality and abundant cooling water are the basis for long service life of the hearth. Some phenomena about cooling system in the commercial blast furnaces were described, and reasonable explanations of these phenomena were analyzed. The results show that increasing the amount of cooling water and reducing the inlet temperature of cooling water can increase the cooling effect significantly in the case of water scaling. Heat flux in the blast furnace hearth is the average heat flux of cooling stave, and the erosion of carbon brick is uneven. There is no direct connection between the actual erosion condition and the heat flux in the hearth. The change trend of thermocouple temperature and heat flux in the hearth can reflect whether the gaps exist among the bricks or not, providing an effective guidance for industrial production and the evaluation of safety state in the hearth. And, the film boiling will not occur in the normal cooling system in the blast furnace hearth.

Design and Operation Control for Long Campaign Life of Blast Furnaces

At the beginning of 1990s, Shougang blast furnaces （BFs） No. 2, No. 4, No. 3 and No. 1 were rebuilt se quently for new technological modernization in succession. The campaign life of BFs No. 1, No. 3 and No. 4 reaches 16.4, 17.6 and 15.6 years, respectively, and the hot metal output of one campaign reaches 33.8, 35.48 and 26.37 Mt, respectively; the hot metal output of BF effective volume of one campaign reaches 13328, 13991 and 12560 t/m^3, respectively, which reaches the international advanced level of BF high efficiency and long campaign life. In BF desig-ning, several advanced BF long campaign technologies were adopted. BF proper inner profile was optimized, reasona- ble inner profile was adopted, and closed circulating soften water cooling technology was applied in 4 BFs. Double row cooling pipe high efficiency cooling stave was developed which could prolong the service life of bosh, belly and stack. Hot pressed carbon brick and ceramic cup hearth lining structure were applied and optimized. BF operation was improved continuously to ensure stable and smooth operation of BF. Hearth working condition control was strengthened, burden distribution control technology was applied to achieve reasonable distribution of gas flow, and heat load monitoring was strengthened to maintain BF reasonable working inner profile. Proper maintenance at the end of BF campaign was enhanced. Hearth and bottom service life was prolonged by adding titaniferous material and enhancing hearth cooling. Gunning of lining was carried out periodically for the area above tuyere zone.

3-D temperature distribution of a full size BF copper stave with oblate channel

An experiment of a new type full size copper stave for a real blast furnacewas carried out in a special-designed experimental system. The 3-D temperature distribution insidethe stave including isotherm was obtained based on the experiment data. And the effects of thetemperature of cooling water and the velocity of the water as well as the temperature of the furnaceon the 3-D temperature distribution were obtained. The experimental and calculation results showthat the highest temperature of the hot surface is lower than 90 deg C which is very good for thesolidified slag formation on the hot surface and protecting the stave.

铜冷却壁长寿的使用维护及结构优化浅析

首钢股份高炉铜冷却壁的长寿使用维护经验,主要是对冷却水温、水量、水压,入炉有害元素及边沿煤气流等进行有效控制,同时对中长期休风和降料面停炉等特殊时段进行专门维护,保障铜冷却壁长期稳定安全运行。针对铜冷却壁在长期使用后可能存在的热面磨损和累积变形,采用热面镶嵌钢砖、本体加强等结构优化设计,能大幅度提高耐磨和挂渣性能,增强抗变形能力,延长在异常工况条件下的使用寿命。认为,只要铜冷却壁设计合理、使用维护得当,就完全能在保障高炉高水平稳定顺行的基础上,实现超过一代炉役的长寿目标。

基于热阻及成本分析的高炉冷却壁多目标优化

本文建立了高炉冷却壁热阻模型,冷却壁热阻包括火积耗散热阻和对流热阻,分别表征其导热性能和换热表面的对流换热性能。分析冷却壁运行过程中的各项成本,包括冷却壁材料成本、运行耗水成本、运行能耗成本以及冷却壁厚度减薄时产生的额外收益。应用遗传算法以冷却壁热阻和成本为目标函数,以冷却壁各结构参数为决策变量,对冷却壁进行多目标优化,获得了Pareto最优解集。优化后的冷却壁与初始冷却壁相比,可在传热性能相当的前提下成本下降79.9%,或在冷却成本相当的前提下,热阻下降27.3%。

新钢7^(#)高炉炉凉事故分析与处理

新钢7^(#)高炉在有上部结厚的情况下计划检修,休风期间炉墙西南结厚物整体坍塌,复风过程因结厚物进入炉缸破坏了热平衡,补加净焦量不够,风口自动吹开,使用质量差的烧结开机料,最终造成炉温大凉。本文通过对高炉炉凉事故起因、处理经过及恢复到正常三个阶段进行了分析,为处理高炉炉凉事故快速恢复提供了宝贵经验。

沙钢2680m^(3)高炉长寿技术特点及铜冷却壁使用效果

沙钢2680m高炉设计及操作遵从炉料膨胀、收缩与炉型相适应的原则,通过设计合理炉型、优化铜冷却壁设计及操作制度等,延长铜冷却壁寿命。炉型设计采用合理的炉腰体积占比(12%~16%);优化炉身上部结构,减少铸铁冷却壁厚度,增加耐材厚度,可降低炉身上部冷却强度,避免边沿气流温度过低影响炉料的干燥和预热;优化铜冷却壁设计,壁体采用侧凸台,加强高炉周向传热的均匀性;优化操作制度,合理调剂上下部制度,增大炉缸活跃区占比,避免软熔带根部位置过低。采用上述措施后,2680m高炉铜冷却壁寿命普遍超过17年,部分达到23年。

酒钢1号高炉冷却壁长寿技术应用简析

酒钢1号高炉大修停炉检查冷却壁基本完好,5~7段铜冷却壁的使用效果明显优于8、9段铸铁冷却壁。1号高炉冷却壁使用效果较好,主要是采用了优化设计炉型、铜冷却壁、增加冷却水量提高冷却强度、联合软水密闭循环冷却系统等技术;同时,存在炉身中下部铸铁冷却壁冷却水流速偏小、冷却强度不足的问题,不易形成稳定的渣皮。认为,铜冷却壁上部的铸铁冷却壁是制约高炉长寿的重要环节,应结合高炉实际原燃料条件和操作制度优化设计,增加炉身下部铜冷却壁的高度,将铜冷却壁延伸至干湿交接部位。