改进型高增益耦合电感Boost-Sepic变换器

针对光伏电池输出电压等级低、稳定性差的问题,本文将Boost-Sepic变换器进行改进,并加入耦合电感与开关电容两种增益单元,提出一种高增益耦合电感组合Boost-Sepic变换器。首先将组合后的Boost-Sepic变换器中输入电感替换为耦合电感原边,保证输入侧电流连续并钳位开关管电压;同时将耦合电感倍压单元与开关电容进行串联以提高电压增益。采用无源钳位吸收回路回收耦合电感漏感的能量,抑制开关管两端产生的电压尖峰。详细分析了Boost-Sepic变换器的工作模态、电压增益、开关器件电压/电流应力及器件参数的选择,并与其他高增益变换器对比。最后,通过200 W实验样机验证了变换器的可行性与正确性。

Recent advancements in continuously scalable conversion-ratio switched-capacitor converter

Switched-capacitor(SC)DC-DC converter[1]is an impor-tant alternative to inductive DC-DC converter,in terms of removing the bulky power inductor.Hence,it is widely used in low-profile,low-power applications,such as the internet of things(IoT)sensor nodes and energy harvesting[2].Mean-while,considering that capacitor has a much higher energy density than inductor,high-power applications.

A real-time calibration method based on time-to-digital converter for accelerator timing system

The high-intensity heavy-ion accelerator facility(HIAF)is a scientific research facility complex composed of multiple cas-cade accelerators of different types,which pose a scheduling problem for devices distributed over a certain range of 2 km,involving over a hundred devices.The white rabbit,a technology-enhancing Gigabit Ethernet,has shown the capability of scheduling distributed timing devices but still faces the challenge of obtaining real-time synchronization calibration param-eters with high precision.This study presents a calibration system based on a time-to-digital converter implemented on an ARM-based System-on-Chip(SoC).The system consists of four multi-sample delay lines,a bubble-proof encoder,an edge controller for managing data from different channels,and a highly effective calibration module that benefits from the SoC architecture.The performance was evaluated with an average RMS precision of 5.51 ps by measuring the time intervals from 0 to 24,000 ps with 120,000 data for every test.The design presented in this study refines the calibration precision of the HIAF timing system.This eliminates the errors caused by manual calibration without efficiency loss and provides data support for fault diagnosis.It can also be easily tailored or ported to other devices for specific applications and provides more space for developing timing systems for particle accelerators,such as white rabbits on HIAF.

Robust optical mode converter based on topological waveguide arrays

Optical mode converters are essential for enhancing the capacity of optical communication systems. However, fabrication errors restrict the further improvement of conventional mode converters. To address this challenge, we have designed an on-chip TE0–TE1mode converter based on topologically protected waveguide arrays. The simulation results demonstrate that the converter exhibits a mode coupling efficiency of 93.5% near 1550 nm and can tolerate a relative fabrication error of 30%. Our design approach can be extended to enhance the robustness for other integrated photonic devices, beneficial for future development of optical network systems.

Energy-Efficient Implementation of BCD to Excess-3 Code Converter for Nano-Communication Using QCA Technology

Code converters are essential in digital nano communication;therefore,a low-complexity optimal QCA layout for a BCD to Excess-3 code converter has been proposed in this paper.A QCA clockphase-based design technique was adopted to investigate integration with other complicated circuits.Using a unique XOR gate,the recommended circuit’s cell complexity has been decreased.The findings produced using the QCADesigner-2.0.3,a reliable simulation tool,prove the effectiveness of the current structure over earlier designs by considering the number of cells deployed,the area occupied,and the latency as design metrics.In addition,the popular tool QCAPro was used to estimate the energy dissipation of the proposed design.The proposed technique reduces the occupied space by∼40%,improves cell complexity by∼20%,and reduces energy dissipation by∼1.8 times(atγ=1.5EK)compared to the current scalable designs.This paper also studied the suggested structure’s energy dissipation and compared it to existing works for a better performance evaluation.

Hydrodynamic Performance of An Integrated System of Breakwater and A Multi-Chamber OWC Wave Energy Converter

A multi-chamber oscillating water column wave energy converter(OWC-WEC)integrated to a breakwater is investigated.The hydrodynamic characteristics of the device are analyzed using an analytical model based on the linear potential flow theory.A pneumatic model is employed to investigate the relationship between the air mass flux in the chamber and the turbine characteristics.The effects of chamber width,wall draft and wall thickness on the hydrodynamic performance of a dual-chamber OWC-WEC are investigated.The results demonstrate that the device,with a smaller front wall draft and a wider rear chamber exhibits a broader effective frequency bandwidth.The device with a chamber-width-ratio of 1:3 performs better in terms of power absorption.Additionally,results from the analysis of a triplechamber OWC-WEC demonstrate that reducing the front chamber width and increasing the rearward chamber width can improve the total performance of the device.Increasing the number of chambers from 1 to 2 or 3 can widen the effective frequency bandwidth.

Negative Stiffness Mechanism on An Asymmetric Wave Energy Converter by Using A Weakly Nonlinear Potential Model

Salter's duck,an asymmetrical wave energy converter(WEC)device,showed high efficiency in extracting energy from 2D regular waves in the past;yet,challenges remain for fluctuating wave conditions.These can potentially be addressed by adopting a negative stiffness mechanism(NSM)in WEC devices to enhance system efficiency,even in highly nonlinear and steep 3D waves.A weakly nonlinear model was developed which incorporated a nonlinear restoring moment and NSM into the linear formulations and was applied to an asymmetric WEC using a time domain potential flow model.The model was initially validated by comparing it with published experimental and numerical computational fluid dynamics results.The current results were in good agreement with the published results.It was found that the energy extraction increased in the range of 6%to 17%during the evaluation of the effectiveness of the NSM in regular waves.Under irregular wave conditions,specifically at the design wave conditions for the selected test site,the energy extraction increased by 2.4%,with annual energy production increments of approximately 0.8MWh.The findings highlight the potential of NSM in enhancing the performance of asymmetric WEC devices,indicating more efficient energy extraction under various wave conditions.

ANovel Non-Isolated Cubic DC-DC Converter with High Voltage Gain for Renewable Energy Power Generation System

In recent years,switched inductor(SL)technology,switched capacitor(SC)technology,and switched inductor-capacitor(SL-SC)technology have been widely applied to optimize and improve DC-DC boost converters,which can effectively enhance voltage gain and reduce device stress.To address the issue of low output voltage in current renewable energy power generation systems,this study proposes a novel non-isolated cubic high-gain DC-DC converter based on the traditional quadratic DC-DC boost converter by incorporating a SC and a SL-SC unit.Firstly,the proposed converter’s details are elaborated,including its topology structure,operating mode,voltage gain,device stress,and power loss.Subsequently,a comparative analysis is conducted on the voltage gain and device stress between the proposed converter and other high-gain converters.Then,a closed-loop simulation system is constructed to obtain simulation waveforms of various devices and explore the dynamic performance.Finally,an experimental prototype is built,experimental waveforms are obtained,and the experimental dynamic performance and conversion efficiency are analyzed.The theoretical analysis’s correctness is verified through simulation and experimental results.The proposed converter has advantages such as high voltage gain,low device stress,high conversion efficiency,simple control,and wide input voltage range,achieving a good balance between voltage gain,device stress,and power loss.The proposed converter is well-suited for renewable energy systems and holds theoretical significance and practical value in renewable energy applications.It provides an effective solution to the issue of low output voltage in renewable energy power generation systems.

Performance Study of a Quadratic Boost Converter

Energy is the driving force behind all economic and industrial development. Africa is the least advanced continent in terms of energy consumption and production. Paradoxically, it is the sunniest continent, which is why our objective is to exploit this energy potential in order to produce and use sufficient energy. To achieve this, we are carrying out a series of studies aimed at developing a device capable of converting solar photovoltaic energy into electrical energy. This device is a two-stage converter, the first of which is a quadratic boost and the second a full bridge. Initially, this paper is devoted to studying the performance of the quadratic boost.

Analysis of Modeling the Influence of Electromagnetic Fields Radiated by Industrial Static Converters and Impacts on Operators Using Maxwell’s Equations

The study of Electromagnetic Compatibility is essential to ensure the harmonious operation of electronic equipment in a shared environment. The basic principles of Electromagnetic Compatibility focus on the ability of devices to withstand electromagnetic disturbances and not produce disturbances that could affect other systems. Imperceptible in most work situations, electromagnetic fields can, beyond certain thresholds, have effects on human health. The objective of the present article is focused on the modeling analysis of the influence of geometric parameters of industrial static converters radiated electromagnetic fields using Maxwell’s equations. To do this we used the analytical formalism for calculating the electromagnetic field emitted by a filiform conductor, to model the electromagnetic radiation of this device in the spatio-temporal domain. The interactions of electromagnetic waves with human bodies are complex and depend on several factors linked to the characteristics of the incident wave. To model these interactions, we implemented the physical laws of electromagnetic wave propagation based on Maxwell’s and bio-heat equations to obtain consistent results. These obtained models allowed us to evaluate the spatial profile of induced current and temperature of biological tissue during exposure to electromagnetic waves generated by this system. The simulation 2D results obtained from computer tools show that the temperature variation and current induced by the electromagnetic field can have a very significant influence on the life of biological tissue. The paper provides a comprehensive analysis using advanced mathematical models to evaluate the influence of electromagnetic fields. The findings have direct implications for workplace safety, potentially influencing standards and regulations concerning electromagnetic exposure in industrial settings.

Robust Nonlinear Current Sensorless Control of the Boost Converter with Constant Power Load

The boost converter feeding a constant power load (CPL) is a non-minimum phase system that is prone to the destabilizing effects of the negative incremental resistance of the CPL and presents a major challenge in the design of stabilizing controllers. A PWM-based current-sensorless robust sliding mode controller is developed that requires only the measurement of the output voltage. An extended state observer is developed to estimate a lumped uncertainty signal that comprises the uncertain load power and the input voltage, the converter parasitics, the component uncertainties and the estimation of the derivative of the output voltage needed in the implementation of the controller. A linear sliding surface is used to derive the controller, which is simple in its design and yet exhibits excellent features in terms of robustness to external disturbances, parameter uncertainties, and parasitics despite the absence of the inductor’s current feedback. The robustness of the controller is validated by computer simulations.

An Adaptive Control Strategy for Energy Storage Interface Converter Based on Analogous Virtual Synchronous Generator

In the DC microgrid,the lack of inertia and damping in power electronic converters results in poor stability of DC bus voltage and low inertia of the DC microgrid during fluctuations in load and photovoltaic power.To address this issue,the application of a virtual synchronous generator(VSG)in grid-connected inverters control is referenced and proposes a control strategy called the analogous virtual synchronous generator(AVSG)control strategy for the interface DC/DC converter of the battery in the microgrid.Besides,a flexible parameter adaptive control method is introduced to further enhance the inertial behavior of the AVSG control.Firstly,a theoretical analysis is conducted on the various components of the DC microgrid,the structure of analogous virtual synchronous generator,and the control structure’s main parameters related to the DC microgrid’s inertial behavior.Secondly,the voltage change rate tracking coefficient is introduced to adjust the change of the virtual capacitance and damping coefficient flexibility,which further strengthens the inertia trend of the DC microgrid.Additionally,a small-signal modeling approach is used to analyze the approximate range of the AVSG’s main parameters ensuring system stability.Finally,conduct a simulation analysis by building the model of the DC microgrid system with photovoltaic(PV)and battery energy storage(BES)in MATLAB/Simulink.Simulation results from different scenarios have verified that the AVSG control introduces fixed inertia and damping into the droop control of the battery,resulting in a certain level of inertia enhancement.Furthermore,the additional adaptive control strategy built upon the AVSG control provides better and flexible inertial support for the DC microgrid,further enhances the stability of the DC bus voltage,and has a more positive impact on the battery performance.

高增益耦合电感组合Boost-Sepic变换器

传统的DC/DC变换器由于其寄生损耗,在高占空比下提供的实际增益有限,对此,此处提出一种高增益耦合电感组合Boost-Sepic变换器。该变换器将耦合电感与开关电容相结合,构成耦合电感倍压单元实现变换器的高电压增益,同时开关电容中的二极管和电容作为无源电压箝位支路,回收耦合电感中漏感储存的能量,而且拓扑组合结构还保留了开关管的无源电压箝位支路,保证了开关管的低电压应力。此处详细分析了该新型Boost-Sepic变换器,包括工作模态、电压增益、开关器件电压应力及器件参数的选择,并与其他高增益变换器进行对比。最后,通过200 W实验样机验证了该变换器的可行性和优点。

Application of Power Electronics Converters in Renewable Energy

Against the backdrop of global energy shortages and increasingly severe environmental pollution,renewable energy is gradually becoming a significant direction for future energy development.Power electronics converters,as the core technology for energy conversion and control,play a crucial role in enhancing the efficiency and stability of renewable energy systems.This paper explores the basic principles and functions of power electronics converters and their specific applications in photovoltaic power generation,wind power generation,and energy storage systems.Additionally,it analyzes the current innovations in high-efficiency energy conversion,multilevel conversion technology,and the application of new materials and devices.By studying these technologies,the aim is to promote the widespread application of power electronics converters in renewable energy systems and provide theoretical and technical support for achieving sustainable energy development.

A Novel Topology of Single-Phase AC-DC Integrated Boost-SEPIC (IBS) Converter Using Common Part Sharing Method (CPSM) for High Step-Up Applications

A novel topology of Integrated Boost-SEPIC (IBS) AC-DC converter using common part sharing method (CPSM) has been proposed in this paper. Conventional boost converters with bridge rectifier configuration are inefficient due to limited voltage step-up ratio which may not be applicable for high step-up applications as in the case of micro generators. The proposed IBS topology is based on the common part sharing method capable of operating both for positive and negative half cycle of the input signal. Result and simulation were conducted using PSIM environment. The proposed AC-DC IBS topology eliminates the requirement of bridge rectifier achieving high efficiency (about 99%), improved power factor (0.75, leading) and lower THD (about 38.8%) which is within IEEE standard.

可拓展增压单元的高增益耦合电感组合Buck-Boost-Sepic变换器原理与设计

提出一种适用于光伏系统、可扩展倍压单元的高增益耦合电感组合Buck-Boost-Sepic变换器。此变换器是由Buck-Boost变换器与Sepic变换器组合,并将储能电感设计成耦合电感并构成倍压单元。变换器不仅得到了理想的电压增益,而且复用电容与二极管形成了无源钳位支路,将漏感能量吸收,阻止了与开关管寄生电容一起引发的谐振,抑制了开关管电压尖峰,降低了开关管的电压应力。分析了变换器的工作原理,给出了变换器的各项性能参数和扩展倍压单元的变换器一般拓扑结构。最后,变换器理论设计的正确性由一台搭建的200 W实验样机得到了验证。

Overview of Precious Metal Content Analysis Methods in Automotive Catalytic Converter

With the increasing awareness of environmental protection, people’s concern of pollution issues arising. Vehicles, as the most important means of transportation, its exhaust emission has received considerable attention. The catalytic converter is able to purify harmful substances in exhaust gas. The absolute content of precious metals in the catalytic converter dominates the exhaust gas purification effect. Accurate detection of precious metal content is of great significance for controlling the cost of catalysts, ensuring catalytic performance and recovering precious metals from spent catalysts. We herein summarized several instruments for precious metals content exploration, such as X-ray fluorescence spectrometer (XRF), atomic absorption spectrometer (AAS), inductively coupled plasma emission spectrometer (ICP) and spectrophotometer. In this thesis, the feasibility of using various devices for characterizing precious metal content in catalytic converters is analyzed and their strengths or weaknesses are elaborated.

Multifunctional polarization converter based on multilayer reconfigurable metasurface

In the modern wireless communication system,the manipulation for polarization of electromagnetic wave plays a important role in improving the capacity and reliability of communication.In this paper,a multifunctional polarization converter(MFPC)based on the multilayer reconfigurable metasurface is proposed,which can assist the source antenna to transmit and receive multiple polarization signals.The MFPC consists of a grating which can filter out the undesired polarization and four layers of metasurfaces incorporated with PIN diodes.The functions of the MFPC include LTC and LTL polarization conversions,co-polarization transmission and reflection for arbitrary polarization.By changing the states of PIN diodes,the functions of MFPC can be dynamically switched.Loaded on the aperture of source antenna,the proposed MFPC can serve as a transmissive array with multiple polarization channels,and can also provide EM protection for source antenna by reflecting the incoming interference waves.Cascading of the metasurfaces produces Fabry-Perot resonance in the MFPC,and it contributes to the realization of LTC and LTL polarization conversions.To verify the performance of the proposed MFPC,the prototype is fabricated and tested.The measured results show that the fractional bandwidths of four functions are all higher than 31.9% with transmission or reflection coefficients higher than-2 d B.The frequency band of each function is mainly concentrated in S-band.The measured data are in agreement with the simulated results.

Large-areaβ-Ga_(2)O_(3) Schottky barrier diode and its application in DC-DC converters

We demonstrate superb large-area verticalβ-Ga_(2)O_(3)SBDs with a Schottky contact area of 1×1 mm^(2)and obtain a high-efficiency DC-DC converter based on the device.Theβ-Ga_(2)O_(3)SBD can obtain a forward current of 8 A with a forward volt-age of 5 V,and has a reverse breakdown voltage of 612 V.The forward turn-on voltage(VF)and the on-resistance(Ron)are 1.17 V and 0.46Ω,respectively.The conversion efficiency of theβ-Ga_(2)O_(3)SBD-based DC-DC converter is 95.81%.This work indicates the great potential of Ga_(2)O_(3)SBDs and relevant circuits in power electronic applications.

Fuzzy Based Interleaved Step-up Converter for Electric Vehicle

This work focuses on the fuzzy controller for the proposed three-phase interleaved Step-up converter(ISC).The fuzzy controller for the proposed ISC converters for electric vehicles has been discussed in detail.The proposed ISC direct current(DC-DC)converter could also be used in automobiles,satellites,industries,and propulsion.To enhance voltage gain,the proposed ISC Converter combines boost converter and interleaved converter(IC).This design also reduces the number of switches.As a result,ISC converter switching losses are reduced.The proposed ISC Converter topology can produce a 143 V output voltage and 1 kW of power.Due to the high voltage gain of this converter design,it is suitable for medium and high-power systems.The proposed ISC Converter topology is simulated in MATLAB/Simulink.The simulated output displays a high output voltage.But the output voltage contains maximum ripples.Fuzzy proposes an ISC Converter which makes closed loop responsiveness and reduces the output voltage ripple.The proposed ISC converter has the lowest ripple output voltage,which is less than 2%,because the duty cycle is regulated using the fuzzy logic controller.It offers high voltage gain,minimal ripple,and low switching loss.The performance of the proposed converter is compared to that of the fuzzy and Pro-portional Integral(PI)controllers implemented in MATLAB.