Evaluation of the Impact of Refined Quality Control Management Model on the Qualified Rate of Disinfection and Sterilization of Surgical Instruments in the Sterilization Supply Center

Objective:To evaluate the application value of a refined quality control management model for a sterilization supply center.Methods:A retrospective analysis was conducted on the work situation of the sterilization supply center from January 2021 to January 2023.The work situation before January 31,2022,was classified as the control group;a routine quality control management model was implemented,and the work situation after January 31,2022,was classified as the observation group.The quality of medical device management and department satisfaction between the two groups were compared.Results:The timely recovery and supply rate,classification and cleaning pass rate,disinfection pass rate,packaging pass rate,sterilization pass rate,and department satisfaction score in the observation group were all higher than those of the control group(P<0.05).Conclusion:Implementing a refined quality control management model in the sterilization supply center can improve the quality management level of medical devices and department satisfaction and is worthy of promotion.

Refined mathematical model for the breaching of concrete-face sand-gravel dams due to overtopping failure

Overtopping is one of the main reasons for the breaching of concrete-face sand-gravel dams(CFSGDs).In this study,a refined mathematical model was established based on the characteristics of the overtopping breaching of CFSGDs.The model characteristics were as follows:(1)Based on the Renormailzation Group(RNG)k-εturbulence theory and volume of fluid(VOF)method,the turbulent characteristics of the dam-break flow were simulated,and the erosion surface of the water and soil was tracked;(2)In consideration of the influence of the change in the sediment content on the dam-break flow,the dam material transport equation,which could reflect the characteristics of particle settlement and entrainment motion,was used to simulate the erosion process of the sand gravels;(3)Based on the bending moment balance method,a failure equation of the concrete face slab under dead weight and water load was established.The proposed model was verified through a case study on the failure of the Gouhou CFSGD.The results showed that the proposed model could well simulate the erosion mode of the special vortex flow of the CFSGD scouring the support body of the concrete face slab inward and reflect the mutual coupling relationship between the dam-break flow,sand gravels,and concrete face slabs.Compared with the measured values,the relative errors of the peak discharge,final breach average width,dam breaching duration,and maximum failure length of the face slab calculated using the proposed model were all less than 12%,thus verifying the rationality of the model.The proposed model was demonstrated to perform better and provide more detailed results than three selected parametric models and three simplified mathematical models.The study results can aid in establishing the risk level and devising early warning strategies for CFSGDs.

Refinement of Bouguer anomalies derived from the EGM2008 model,impact on gravimetric signatures in mountainous region:Case of Cameroon Volcanic Line,Central Africa

Global geopotential models have not included the very high frequencies of the Earth’s external gravity field.This is called omission error.This omission error becomes more important in mountainous areas(areas with highly variable topography).The work reported here consists in reducing the omission error in measurements of Bouguer gravity anomalies,by refining the global geopotential model EGM2008 using the spectral enhancement method.This method consists in computing the residual terrain effects and then coupling them to the gravimetric signal of the global geopotential model.To compute the residual terrain effects,we used the Residual Terrain Model(RTM)technique.To refine it required a reference surface(ETOPO1)developed up to degree 2190(the maximum degree of the EGM2008 model)and a detailed elevation model(AW3D30).Computation was performed with the TC program of the GRAVSOFT package.The topography of the study area was assumed to have a constant density of 2670 kg/m3.For the inner and outer zones,the respective integration radii of 10 km and 200 km have been chosen.We obtained very important RTM values ranging from−53.59 to 34.79 mGal.These values were added to the gravity anomalies grid of the EGM2008 model to improve accuracy at high frequencies.On a part of the Cameroon Volcanic Line and its surroundings(mountainous area),we made a comparison between the residual Bouguer anomalies before and after refinement.We report differences ranging from−37.40 to 26.40 mGal.We conclude that the impact of omission error on gravimetric signatures is observed especially in areas with high variable topography,such as on the Cameroon Volcanic Line and around the localities of Takamanda,Essu,Dumbo,and Ngambe.This finding illustrates the great influence that topography has on accurate measurement of these gravity anomalies,and thus why topography must be taken into account.We can conclude that in preparing a global geopotential model,a high resolution DTM must be used to decrease the omission error:the degree of expansion has to increase in order to take the higher frequencies into account.The refined Bouguer anomalies grid presented here can be used in addition to terrestrial gravity anomalies in the study area,especially in mountainous areas where gravimetric data are very sparse or nonexistent.

Model Refinement for Offshore Platforms： Experimental Study

Offshore jacket platforms are widely used in offshore oil and gas exploitation.Finite element models of such structures need to have many degrees of freedom(DOFs) to represent the geometrical detail of complex structures,thereby leading to incompatibility in the number of DOFs of experimental models.To bring them both to the same order while ensuring that the essential eigen-properties of the refined model match those of experimental models,an extended model refinement procedure is presented in this paper.Vibration testing of an offshore jacket platform model is performed to validate the applicability of the proposed approach.A full-order finite element model of the platform is established and then tuned to meet the measured modal properties identified from the acceleration signals.Both model reduction and modal expansion methods are investigated,as well as various scenarios of sensor arrangements.Upon completion of the refinement,the updated jacket platform model matches the natural frequencies of the measured model well.

Hybrid Neural Network Model for RH Vacuum Refining Process Control

A hybrid neural network model,in which RH process(theoretical)model is combined organically with neural network(NN)and case-base reasoning(CBR),was established.The CBR method was used to select the operation mode and the RH operational guide parameters for different steel grades according to the initial conditions of molten steel,and a three-layer BP neural network was adopted to deal with nonlinear factors for improving and compensating the limitations of technological model for RH process control and end-point prediction.It was verified that the hybrid neural network is effective for improving the precision and calculation efficiency of the model.

Modelling of an hydraulic excavator using simplifiedrefined instrumental variable(SRIV)algorithm

Instead of establishing mathematical hydraulic system models from physical laws usually done with the problems of complex modelling processes, low reliability and practicality caused by large uncertainties, a novel modelling method for a highly nonlinear system of a hydraulic excavator is presented. Based on the data collected in the excavator＇s arms driving experiments, a data-based excavator dynamic model using Simplified Refined Instrumental Variable （SRIV） identification and estimation algorithms is established. The validity of the proposed data-based model is indirectly demonstrated by the performance of computer simulation and the.real machine motion control exoeriments.

ARTIFICIAL NEURAL NETWORK MODELLING OF A WOOD CHIP REFINER

1 INTRODUCTIONWood chip refining is the most critical step in mechanical pulping.Commercical experi-ences have been gained for years.Modelling and control of chip refiners,however,pose a challenge mainly because of the stochastic nature of the process.Some attemptshave been made to employ factor analysis technique[1]in the modelling andsimulating of refiner operation[2,3].Strand[2]used common factors as links betweenintrinsic fibre properties and pulp quality.He believed that a qualitative concept onthe physical nature of these common factors could be arrived at,and thus would helpto understand what refining variables need to be controlled or adjusted in order to im-prove pulp quality.However,the linear model used in factor analysis is based on theassumption that the interactions among the system variables are linear,which,ofcourse,is not true in practice.

Physical Modeling of the Vacuum Circulation Refining Process of Molten Steel

The available studies in the literature on physical modeling of the vacuum circulation (RH, i.e. Ruhrstahl Heraeus) refining process of molten steel have briefly been reviewed. The latest advances made by the author with his research group have been summarized. Water modeling was employed to investigate the flow and mixing characteristics of molten steel under the RH and RH KTB (Kawasaki top blowing) conditions and the mass transfer features between molten steel and powder particles in the RH PTB (powder top blowing) refining. The geometric similarity ratio between the model and its prototype (a multifunction RH degasser of 90 t capacity) was 1:5. The effects of the related technological and structural factors were considered. These latest studies have revealed the flow and mixing characteristics of molten steel and the mass transfer features between molten steel and powder particles in these processes, and have provided a better understanding of the refining processes of molten steel.

Effect of Ca addition on grain refinement of Mg–9Li–1Al alloy

The as-cast and as-extruded Mg–9Li–1Al–xCa alloys(x=0,0.2;wt%)were prepared by a simple alloying process followed by hot extrusion with an extrusion ratio of 28.2.The microstructures of the as-cast and as-extruded Mg–9Li–1Al–xCa alloys were observed to investigate the effect of calcium(Ca)element on the Mg–9Li–1Al(LA91)alloy,and the crystallographic calculations between Al_(2)Ca and the matrix(α-Mg andβ-Li phases)were examined on the basis of the edge-to-edge matching model.The experimental results indicate that the addition of 0.2 wt%Ca into LA91 alloy reduce the size of theα-Mg phases in the as-cast alloy and that ofβ-Li phases in the as-extruded alloy due to the Al_(2)Ca particles distributed inside the matrix.Crystallographic calculation results suggested that there is a good crystallographic matching between the matrix and Al_(2)Ca,which confirmed that Al_(2)Ca particles can act as a heterogeneous nucleation site for bothα-Mg andβ-Li phases and were effective grain refiners for LA91 alloy.

Mathematical Modeling of the Vacuum Circulation Refining Process of Molten Steel

The available studies in the literature on mathematical modeling of the vacuum circulation (RH) refining process of molten steel have briefly been reviewed. The latest advances obtained by the author with his research group have been summarized. On the basis of the mass and momentum balances in the system, a new mathematical model for decarburization and degassing during the RH and RH KTB refining processes of molten steel was proposed and developed. The refining roles of the three reaction sites, i.e. the up snorkel zone, the droplet group and steel bath in the vacuum vessel, were considered in the model. It was assumed that the mass transfer of reactive components in the molten steel is the rate control step of the refining reactions. And the friction losses and drags of flows in the snorkels and vacuum vessel were all counted. The model was applied to the refining of molten steel in a multifunction RH degasser of 90 t capacity. The decarburization and degassing processes in the degasser under the RH and RH KTB operating conditions were modeled and analyzed using this model. Besides, proceeded from the two resistance mass transfer theory and the mass balance of sulphur in the system, a kinetic model for the desulphurization by powder injection and blowing in the RH refining of molten steel was developed. Modeling and predictions of the process of injecting and blowing the lime based powder flux under assumed operating modes with the different initial contents of sulphur and amounts of powder injected and blown in a RH degasser of 300 t capacity were carried out using the model. It was demonstrated that for the RH and RH KTB refining processes, and the desulphurization by powder injection and blowing in the RH refining, the results predicted by the models were all in good agreement respectively with data from industrial experiments and practice. These models may be expected to offer some useful information and a reliable basis for determining and optimizing the technologies of the RH and RH KTB refining and desulphurization by powder injection and blowing in the RH refining and for controlling the processes.

Semiparametric Regression and Model Refining

This paper presents a semiparametric adjustment method suitable for general cases.Assuming that the regularizer matrix is positive definite,the calculation method is discussed and the corresponding formulae are presented.Finally,a simulated adjustment problem is constructed to explain the method given in this paper.The results from the semiparametric model and G_M model are compared.The results demonstrate that the model errors or the systematic errors of the observations can be detected correctly with the semiparametric estimate method.

On well-posedness of two-phase nonlocal integral models for higher-order refined shear deformation beams

Due to the conflict between equilibrium and constitutive requirements,Eringen’s strain-driven nonlocal integral model is not applicable to nanostructures of engineering interest.As an alternative,the stress-driven model has been recently developed.In this paper,for higher-order shear deformation beams,the ill-posed issue(i.e.,excessive mandatory boundary conditions(BCs)cannot be met simultaneously)exists not only in strain-driven nonlocal models but also in stress-driven ones.The well-posedness of both the strain-and stress-driven two-phase nonlocal(TPN-Strain D and TPN-Stress D)models is pertinently evidenced by formulating the static bending of curved beams made of functionally graded(FG)materials.The two-phase nonlocal integral constitutive relation is equivalent to a differential law equipped with two restriction conditions.By using the generalized differential quadrature method(GDQM),the coupling governing equations are solved numerically.The results show that the two-phase models can predict consistent scale-effects under different supported and loading conditions.

The Refinement Algorithm Consideration in Text Clustering Scheme Based on Multilevel Graph

To construct a high efficient text clustering algorithm the multilevel graph model and the refinement algorithm used in the uncoarsening phase is discussed. The model is applied to text clustering. The performance of clustering algorithm has to be improved with the refinement algorithm application. The experiment result demonstrated that the multilevel graph text clustering algorithm is available. Key words text clustering - multilevel coarsen graph model - refinement algorithm - high-dimensional clustering CLC number TP301 Foundation item: Supported by the National Natural Science Foundation of China (60173051)Biography: CHEN Jian-bin(1970-), male, Associate professor, Ph. D., research direction: data mining.

Refined Aerodynamic Test of Wide-Bodied Aircraft and Its Application

The large dual-channel wide-bodied aircraft has a long range and a high cruise Mach number.Therefore,its aerodynamic design requires a high level ofwind tunnel test refinement.Based on the requirements of aerodynamic design for the future wide-bodied aircraft and the characteristics of high-speed wind tunnel tests,the error theory is introduced to analyze the factors affecting the accuracy of the test data.This study carries out a series of research on the improvement of refined aerodynamic test technology in an FL-26 wind tunnel,including design and optimization of the support system of wide-bodied aircraft,model attitude angle measurement,Mach number control accuracy,measurement and control system stability,test data correction and perfection,high-precision force balance and standard model development.In addition,the effect of the standard specification of the refined aerodynamic test is investigated to improve the data quality.The research findings have been applied in the standard model test and subsequent models of wide-bodied aircraft.The results show that whenMach numbers are less than 0.9,the control accuracy of Mach numbers in the FL-26 wind tunnel is smaller than 0.001 and the measurement error of attack angle is smaller than 0.01°.Therefore,it has the ability to correct the data influenced by factors,such as support/wall interference,model deformation,floating resistance and airflow deflection angle.The repeatability accuracy of the standard model’s comparison test shows that the lift coefficient is less than or equal to 0.0012,the drag coefficient is less than or equal to 0.00004,pitching moment coefficient is less than or equal to 0.0004.The bending resolution of the model’s deformation measurement is less than 0.2 mm,and the tensional deformation is smaller than 0.04°.The revised aerodynamic data and model deformation measurement results have good agreement with that of the ETW wind tunnel.The results demonstrate that the improved technology presented in this paper can significantly enhance the refined aerodynamic test of wide-bodied aircraft.

Refinement and Quantification of Terrain-Induced Effects on Global Gravity Data

The geodetic and geophysical applications of Earth Gravity Field parameters computed from Global Geopotential Models (GGMs) are quite on the increase despite the inherent commission and omission errors of these models. In view of this, this study focuses on refining and quantifying terrain-induced effects on Bouguer gravity anomalies computed directly from a total of seven recent GGMs. In the study, the Residual Terrain Model (RTM) technique was used to estimate the residual terrain effects that were added to the GGM-computed Bouguer gravity anomalies at the sixty test points in Enugu State, Nigeria. The computed residual terrain effects range from -24.6 to 37.5 mgal while the percentage of the omission errors of the GGMs based on their Root-Mean-Square (RMS) differences ranges from 7.8% to 44.7%. It can be concluded that GGM-refined Bouguer gravity anomalies are better in accuracy than the unrefined GGM-computed Bouguer gravity anomalies and hence there is need for accurate height information in the development of GGMs. We, therefore, recommend that refined Bouguer gravity anomalies obtained from HUST-Grace2016s, EIGEN-6C4 and GECO that gave best improvement amongst the seven GGMs under consideration should be used to supplement the available terrestrial Bouguer anomalies for geodetic and geophysical applications within the study area.

Modeling Operational Parameters of a Reactive Electro-Dialysis Cell for Electro-Refining Anodic Scrap Copper

This work will create an electro-dialysis cell model that has the purpose of refining anodic scrap copper—an element that currently must be returned to the copper conversion process. The cell modeling is based on Ohm’s Law, while the resulting copper deposit morphology is studied through the thickness of the layer deposited on the surface and the electric current lines traced from the anode to the cathode. The use of the model demonstrated that it is possible to effectively predict the specific energy consumption required for the refinement of the anodic scrap copper, and the morphology of the cathode obtained, with a margin of error of 9%.

Combined back-analysis method of ground stress based on refined geological modeling

A new back-analysis method of ground stress is proposed with comprehensive consideration of influence of topography, geology and nonlinear physical mechanical properties of rock on ground stress. This method based on non-uniform rational B-spline (NURBS) technology provides the means to build a refined three-dimensional finite element model with more accurate meshing under complex terrain and geological conditions. Meanwhile, this method is a back-analysis of ground stress with combination of multivariable linear regression model and neural network (ANN) model. Firstly, the regression model is used to fit approximately boundary loads. Regarding the regressed loads as mean value, some sets of boundary loads with the same interval are constructed according to the principle of orthogonal design, to calculate the corresponding ground stress at the observation positions using finite element method. The results (boundary loads and the corresponding ground stress) are added to the samples for ANN training. And on this basis, an ANN model is established to implement higher precise back-analysis of initial ground stress. A practical application case shows that the relative error between the inversed ground stress and observed value is mostly less than 10 %, which can meet the need of engineering design and construction requirements.

铝合金细化剂细化行为研究现状与展望

晶粒细化处理能够显著改善铝合金的综合性能,对拓展其应用领域意义重大。本文基于异质形核,探讨了点阵错配模型、边边匹配模型以及自由生长模型,肯定了边边匹配模型在筛选潜在晶粒细化剂方面的高效性;根据自由生长模型关于异质相尺寸、形态、分布等对晶粒细化效果影响的理论研究,归纳了物理、化学方法调控第二相进而优化细化效果的研究进展,并且对第二相尺寸影响细化效果的原因进行了理论阐述,最后对优化晶粒细化剂的方向做了展望。

基于CAPE-OPEN标准的简捷炼油过程建模及常减压蒸馏流程在线模拟

简捷炼油过程模型广泛应用于运行监测、在线计算、实时优化等领域,但大多数模型只是将输入、输出变量进行关联,无法计算出各组分流量组成,难以集成在模拟软件中进行全流程模拟。本研究简化了炼油分离过程,开发了基于CAPE-OPEN标准的简捷炼油塔模型。首先,将炼油过程简化为连续的分离单元,根据实际产品数据校正模型参数,实现某一实际工况流程模拟;其次,将模型参数与实际工况操作变量数据相结合,采用径向基函数插值确定操作变量对模型参数的影响关系,实现多种工况流程模拟;最后,通过常减压蒸馏工业装置实例的3种工况进行验证。结果表明:各工况模拟结果与Aspen计算结果相比,初馏塔塔顶油馏出温度点偏差大多在2%以内,常减压蒸馏塔各侧线油的馏出温度点平均偏差在3%以内;与实际结果相比,平均误差都在5%以内,符合工程允许误差范围要求。所建模型的计算速度快,各塔均在0.2 s左右完成计算,适用于在线生产、调度等。