New Method to Restrain Pumping Voltage of Braking Procedure for Brushless DC Motor of Electric Armored Vehicle

In order to restrain the high pumping voltage of braking procedure which is harmful to the system of electric armored vehicle. Based on the analysis of pumping voltage of the braking procedure, the relation between pumping voltage and PWM ratio is derived and a new digital control method to restrain the pumping voltage by changing PWM ratio is put forward. Because the capacitance is decreased effectively, the volume of controller is reduced and the performance to price ratio is improved. The results of computer simulation and experiment proved that this method is feasible and valid.

Anti-reverse rotation startup method for sensorless brushless DC motor

In order to start up the brushless DC motor （BLDCM） without reverse rotation and smoothly switch the running state of the motor, a novel startup and smoothly switching method for a sensodess BLDCM is presented. Based on the saturation effect of the stator iron, six short voltage pulses are applied to determine the initial rotor position and the rotor can be found within 60°. After that, a series of short and long voltage pulses are used to accelerate the motor and the variation of the response current is utilized to detect the rotor position dynamically. When the motor reaches a certain speed at which the back-electromotive force （EMF） method can be applied, all the power devices are turned off and the running state of the motor is smoothly switched at the moment determined by the relationship between the terminal voltage waveform and the commutation phases. The experimental results verify the feasibility and validity of the proposed method.

EFFECTIVE DOUBLE LOOP CONTROL FOR A SQUARE WAVE BRUSHLESS DC MOTOR

A new type of brushless DC motor has been developed by using a square wave rare earth permanent magnet synchronous motor with its double loop control circuit. The double loop control scheme of the drive system yields a combination of desired characteristics including simplified control structure, small ripple torque, high speed accuracy, wide operating speed range, and fast dynamic response. Experimental results confirm excellent characteristics of the motor.

Simulation Research of Fault Model of Detecting Rotor Dynamic Eccentricity in Brushless DC Motor Based on Motor Current Signature Analysis

基于Ansoft／Maxwell设置动态偏心故障，建立求解电机电感和磁链的有限元模型，通过仿真，证明了将感应电机动态偏心故障的特征频率经过简化后，同样适用于无刷直流电动机。基于Ansoft／Simplorer建立无刷直流电动机系统的仿真模型。在电机稳态运行下，对定子电流进行傅里叶分析，研究并建立基于定子电流监测动态偏心故障的仿真模型：动态偏心故障与特征频率的关系、动态偏心故障程度与特征频率幅值的关系。进而研究了无刷直流电动机稳态运行时转速波动对偏心故障监测的影响。仿真结果表明，转子偏心程度加大，特征频率的幅值增加。

Robust Control Strategy for the Speed Control of Brushless DC Motor

Brushless DC motor ( BLDCM) speed servo system is multivariable,nonlinear and strong coupling. The parameter variation, the cogging torque and the load disturbance easily influence its performance. Therefore,it is difficult to achieve superior performance by using the conventional PID controller. To solve the deficiency,the paper represents the algorithm of active-disturbance rejection control ( ADRC) based on back-propagation ( BP) neural network. The ADRC is independent on accurate system and its extended-state observer can estimate the disturbance of the system accurately. However,the parameters of Nonlinear Feedback ( NF) in ADRC are difficult to obtain. So in this paper,these parameters are self-turned by the BP neural network. The simulation and experiment results indicate that the ADRC based on BP neural network can improve the performances of the servo system in rapidity,control accuracy,adaptability and robustness.

Comparative Study between the PID Regulator and the Fuzzy Regulator Applied to the Operation of a Brushless DC Motor

This paper presents the results of research on speed regulation of a brushless DC motor. This is mainly a comparative study between a PID regulator and a fuzzy regulator applied to the operation of this type of engine in order to find the best control. The BLDC engine must operate under various speed and load conditions with improved performance and robust and complex speed control. Because of this complexity, the traditional PID command encounters difficulties in controlling the speed of a BLDC. Another control technique is currently developing and is producing good results. This is the fuzzy controller that handles process control problems, that is, managing a process based on a given set point per action on the variables that describe the process. To achieve the desired results, the brushless DC machine model will be studied. With the model obtained, both types of regulator will be tested. A synthesis of the observed comparison results will enable a conclusion to be drawn on the performance of the two types of regulators driving a BLDC (Brushless DC).

A neural network-based commutation optimization strategy and drive system design for brushless DC motor

An optimized commutation method based on backpropagation(BP)neural network is proposed to resolve the low stability and high-power consumption caused by inaccurate commutation point prediction in conventional commutation strategy during acceleration and deceleration.This article also builds a complete brushless DC motor drive system based on the GD32F103 micro control unit(MCU),with an Artix-7 XC7A35T field programmable gate array(FPGA)to meet the performance requirements of neural network calculation for real-time motor commutation control.Experimental results show that the proposed optimization strategy can effectively improve the system stability during system acceleration and deceleration,and reduce the current spikes generated during speed chan-ges.The system power consumption is reduced by about 11.7%on average.

Design and implementation of a position sensorless control method for brushless DC motors

Because brushless direct current(BLDC) motors have the advantages of a compact size, high power density, high efficiency, and long operating life time, they are widely used in many industrial products and electric traction systems. It is known that the BLDC motors have no brushes for commutation. They are commutated with electronically commutation. So, the rotor position information of the BLDC motors must be known to understand which winding will be energized according to the energizing sequence. In most of the existing BLDC motor drivers, rotor position information is detected by Hall effect sensors. This kind of mechanical position sensors will bring additional connections and costs, reliability decrease and noise increase. In order to improve the control performance and extend the range of speed regulation for BLDC motors, a position sensorless control method is proposed in this paper. In the proposed control method, rotor position information of the BLDC motors is detected from the back electromagnetic forces(back-EMFs) which are estimated by an unknown-input observer with line to line currents and line to line voltages. For the purpose of verifying the effectiveness of the proposed control method, a model is built and simulated on the Matlab/Simulink platform. The simulation results show that the speed regulation performance of BLDC motors is improved compared with using Hall effect sensors. At the same time, the reliability of the BLDC motors is improved and the costs of them are reduced because the position sensor is eliminated.

High temperature brushless DC motor system and its operation mode control

The high temperature (175 ℃) operation of a motor spells out special requirements for control algorithms, materials and elements. The stability of motor characteristic is guaranteed by the digital control strategy. Constant velocity operation is achieved by phase locked loop (PLL), and constant power operation is achieved by a current restricting circuit. A motor for constant speed and constant power operation has been built and the speed control system is tuned by MATLAB simulation. Experimental and simulation results for operation mode control of brushless DC motor are presented.

Sensorless Control of Four-Switch Inverter for Brushless DC Motor Drive and Its Simulation

The major function of this proposed research is to control the speed of the brushless DC motor with sensor less control for four-switch three phase inverter. This proposed system is simplified the topological structure of the conventional six-switch three phase inverter. In this proposed method, a new structure of four-switch three phase inverter [1] with reduced number of switches for system is introduced to reduce the mechanical commutation, switching losses that occur in the six-switch method. The proposed inverter fed brushless DC motor used in sensorless control schemes which is used for sensing positioning signals. To improve sensor less control performance, four-switch electronic commutation modes based proportional intergral controller scheme is implemented. In this four-switch three phase inverter reduction of switches, low cost control and saving of hall sensor were incorporated. The feasibility of the proposed sensor less control four-switch three phase inverter fed brushless DC motor drive is implemented, analysed using MATLAB/SIMULINK, effective simulation results have been validated out successfully.

Solar PV System for Energy Conservation Incorporating an MPPT Based on Computational Intelligent Techniques Supplying Brushless DC Motor Drive

This paper proposes an effective Maximum Power Point Tracking (MPPT) controller being incorporated into a solar Photovoltaic system supplying a Brushless DC (BLDC) motor drive as the load. The MPPT controller makes use of a Genetic Assisted Radial Basis Function Neural Network based technique that includes a high step up Interleaved DC-DC converter. The BLDC motor combines a controller with a Proportional Integral (PI) speed control loop. MATLAB/Simulink has been used to construct the dynamic model and simulate the system. The solar Photovoltaic system uses Genetic Assisted-Radial Basis Function-Neural Network (GA-RBF-NN) where the output signal governs the DC-DC boost converters to accomplish the MPPT. This proposed GA-RBF-NN based MPPT controller produces an average power increase of 26.37% and faster response time.

Highly Effective Brushless DC Motor in Which Unidirectional Current Flows in

Authors developed a highly effective brushless DC motor with a simple operation principle. If the operation principle of the motor is simple, a drive circuit will also become simple and its production cost will be lower. From the above fact, Minato motor was noticed. In this motor, a unidirectional current flows in the electromagnets. In other words, unidirectional windings are used. In this motor, only strong repulsive force is utilized when a permanent magnet of a rotor and an electromagnet of a stator are adjacent. Hence, torque constant becomes higher and the efficiency of the motor is high. However, an effective value of the electromagnetic current increases because a large current flows in a short period. Therefore, copper loss increases and the efficiency of the motor decreases. In order to solve above defects, a new motor is proposed. From the experiment, it is clarified that the efficiency of the proposed motor is higher than that of the commercial motors.

Steady-State Performance Analysis of Brushless DC Propulsion Motor

The brushless DC motor can be used in the marine electric propulsion system for its excellent control characteristics and large thrust. In order to estimate the operating performances of the brushless DC motor for the high-power shipping during the design stage, the steady-state analysis is as important as the dynamic analysis generally. A mathematical model of the brushless DC propulsion motor is established according to the state-space method for the dynamic and steady-state performance analysis. The state-space mathematical model is a set of linear differential equations, so the steady-state currents of the armature windings can be gained directly by the symmetrical boundary conditions and the eigenvalues of the system matrix. The steady-state simulation results are compared with the dynamic ones to validate the correctness of this eigenvector method.

Properties of Brushless DC Machine Induced by Permanent Magnets Applied to a Traction Drive

The paper presents a mathematical model ofbrushless DC machine induced by permanent magnets. Its construction uses the classical model of permanent magnet synchronous machine and induced model of power inverter using the serraphil form. The results of the computer simulation were presented for such states： startup, work under active constant load and the behavior of the machine in terms of exponential and stepping change of the power inverter＇s control angle.

An Advance Commutation Control Method for Low Torque Ripple of Brushless DC Motors

该文给出一种优化的无刷直流电动机变母线电压六拍控制方法。既解决了传统六拍控制策略中由于绕组电感所造成的电流滞后问题,又改善了由于换相所造成的电流脉动问题。该方法是通过在每两拍之间插入一小段缓冲区来实现的,该缓冲区使下一拍将要切入的电流提前切入,同时使当前拍将要切出的电流延迟切出。通过确定缓冲区的起始位置,即超前换相角的大小,保证每一拍所对应的相电流的中心和反电动势的中心重合。通过选取缓冲区开关器件PWM调制的占空比,降低电机运行过程中的换相转矩脉动。该文方法只需根据负载大小选取超前换相角,一旦选定适用于所有转速。文中给出了该方法的理论推导过程和实验验证波形,从实验结果可以发现,电流滞后被消除,换相电流脉动显著减小,电机的利用率得到提高。

Analysis of torque-current characteristic of brushless DC motor driven by three-phase H-bridge

Presents the simulation and analysis of the steady state characteristic of a brushless DC motor studies the torque current characteristic of the motor as well and discusses the design of a current measure circuit for torque controlling.

Analysis of the Magnetic Flux Density, the Magnetic Force and the Torque in a 3D Brushless DC Motor

As permanent magnet motors and generators produce torque, vibration occurs through the small air gap due to the alternating magnetic forces created by the rotating permanent magnets and the current switching of the coils. The magnetic force can be calculated from the flux density by finite element methods and the Maxwell stress tensor in cy-lindrical coordinates. In this paper the magnetic flux density, the magnetic force and the torque of a real three dimen-sional brushless DC motor are simulated using Maxwell 3 D V 11.1.

Temperature Research of Permanent Magnet Brushless DC Motor for Electric Balanced Vehicle

A power system structure composed of a brushless DC motor and a cycloidal reducer for electric balanced vehicle has been proposed, and the temperature of important components in this structure would be discussed. The loss generated by the cycloid reducer is negligible, it’s only need to analyze the thermal field of motor. Since the temperature change will affect the material properties of the target motor, the electromagnetic and temperature fields, involved in the motor, are selected for coupling calculation to determine whether the final temperature distribution can meet the requirements of vehicle for use.

基于模糊BP神经网络的智能轮椅BLDCM控制

现阶段多数轮椅电机仍使用传统PID控制,该控制方式存在控制精准度较低、超调量较大以及抗扰动能力差等问题。为解决以上问题,通过对无刷直流电机进行研究,在分析了其控制方法后,提出一种基于模糊BP神经网络的BLDCM控制方法。首先,研究了BLDCM结构并搭建数学模型。其次,在模型基础上构建了模糊BP神经网络PID控制器。最后,在Matlab/Simulink中搭建整个电机控制系统进行三种不同工况下的运动控制仿真,并与传统PID控制算法进行对比。实验结果表明:模糊BP神经网络PID控制策略能获得更好的PID控制参数,具有良好的抗扰动能力,有效的改善了整个轮椅控制系统的动态性能。

Design of Electrical/Mechanical Hybrid 4-Redundancy Brushless DC Torque Motor

This article presents a novel electrical/mechanical hybrid 4-redundancy brushless DC torque motor （BLDCM）, which has found applications in direct drive actuators （DDA） of aerial vehicles. This motor is characteristic of electrical/mechanical hybrid 4-redundancy by securing two stators along with two rotors on the same shaft. Each stator contains two sets of windings embed- ded in separated slots. Furthermore, compared to the scheme of two electrical dual-redundancy BLDCMs linked by a mechanical transmission, the proposed motor has lower volume and lighter weight, eliminates the nonlinearity caused by the gap of the me- chanical transmission, moderates the requirement for the torque balance between redundancies and reduces the cogging torque by shifting the magnets. Both magnetic circuit calculation and the finite element analysis （FEA） of the electromagnetic field are conducted to optimize the design process. A prototype motor has been produced and tested. The results indicate that its perform- ances comply with the requirements presented by designers. Moreover, the position frequency response of the prototype in the DDA＇s unloaded situation has also demonstrated the fulfillment of desired dynamic characteristics.